Verity Audio Tamino Monitor - Packing User Manual

1005 Saint-Jean-Baptiste, Suite 150
Quebec, QC G2E 5L1 Canada

Tamino

Monitor

Product Unpacking Instructions

Product Unpacking Instructions

Product Unpacking InstructionsProduct Unpacking Instructions

The packaging accessories are:

i. (1) 18" x 14" x 19" cardboard box;
ii. (1) Inner cardboard sleeve;
iii. (1) Accessory box;
iv. (2) Top / bottom protective foam covers;
v. (1) Speaker grille;
vi. (1) Package containing the owner’s manual and

registration card.

The accessory box contains:

i. (2) Connector posts.

1. Place one cardboard box on its back. See the printings on
the cardboard box;

2. Cut the two black straps;

3. Cut the packing tape that surrounds the cover;

4. Completely open the cover;

5. Extract the four wooden boards from each side;

6. Flip the cardboard in a manner to have the inner
cardboard sleeve on its upright position;

7. Gently take the inner cardboard sleeve and slide it
completely outside the main cardboard box;

8. Remove the loudspeaker grille and the owner’s manual
from the top protective foam board.

9. Cut the black straps fixed on the inner cardboard sleeve;

10. Gently take away the inner cardboard sleeve by sliding it
all the way up;

11. Remove the protective foam cover inserted on top of the
loudspeaker;

12. Detach the accessory box from the protective foam cover;

13. Carefully insert the hands inside the bottom protective
foam cover in order to take the bottom of the loudspeaker.
While lifting the loudspeaker, dislodge it from the bottom
foam cover.

14. Remove the plastic covering the monitor;

15. Screw the connector posts halfway at the rear of each
monitor;

16. For proper installation, please read the Installation
Chapter of the manual;

17. Place unused accessories inside the box and store it away.

2004.06.30

Tel: [phone]
Fax: [phone]

www.verityaudio.com

[e-mail]

1005 Saint-Jean-Baptiste, Suite 150
Quebec, QC G2E 5L1 Canada

Tamino

Monitor

Product Packing Instructions

Product Packing Instructions

Product Packing InstructionsProduct Packing Instructions

The packaging accessories are:

i. (1) 18" x 14" x 19" cardboard box;
ii. (1) Inner cardboard sleeve;
iii. (1) Accessory box;
iv. (2) Top / bottom protective foam covers;
v. (1) Speaker grille;
vi. (1) Package containing the owner’s manual and

registration card.

The Tamino Monitor loudspeaker is packed in a cardboard box
and provides space for:

i. (1) Tamino Monitor loudspeaker;
ii (1) Speaker grille;
iii. (1) Accessory box.

The accessory box contains:

i. (2) Connector posts.

1. Turn off the power amplifier(s);

2. Completely unscrew the two connector posts from the
Tamino Monitor loudspeaker and disconnect the speaker
cable;

3. Store two connector nuts in the accessory box;

4. Wrap the monitor with the plastic covering;

5. Lift and insert it into the bottom foam cover;

6. Place the top foam cover on top;

7. Cover the monitor with the inner cardboard box;

8. Strap the outside of the inner cardboard box in order to
hold together the bottom foam cover, the inner cardboard
box, and the top foam cover;

9. Open the main cardboard and place it in its vertical
position. Follow the directions printed on the main
cardboard box;

10. Gently slide the inner cardboard box inside the main
cardboard box, the front of the loudspeaker facing the
opening;

11. Carefully tilt and lay the main cardboard box on its back;

12. Place the four protective wooden boards inside the main
cardboard. One on each side.

13. Slide one grille between the top foam cover and the main
cardboard. The grille’s studs should be pointing towards
the speaker and plunged inside the foam;

14. Slide the owner’s manual between the wooden board and
the main cardboard box;

15. Close the cover of the box and tape it adequately;

16. Strap the box;

17. The Tamino Monitor is ready to be addressed and
shipped.

2004.06.30

Tel: [phone]
Fax: [phone]

www.verityaudio.com

[e-mail]