Verity Audio Rocco - Packing User Manual

1005 Saint-Jean-Baptiste, Suite 150
Quebec, QC G2E 5L1 Canada

ROCCO

Product Unpacking Instructions

The packaging contains :

i. (1) ATA approved flight case;
ii. (1) Power cord;
iii. (2) Speaker grilles;
iv. (1) Hardened glass;
v. (2) Accessory boxes;
vi. (1) Package containing the owner's manual.

One accessory box contains :

i. (4) Threaded spikes;
ii. (4) Threaded spikes locking nuts.

The other accessory box contains :

i. (9) Sorbothane bumpers.

WARNING: The Rocco’s module and its packaging are big and
heavy. Any operations that ask for moving, lifting or tilting will
require the assistance of a second person. Attempting to do it
alone could be hazardous, create injuries or permanent
damage to the loudspeaker.

1. Cut and remove the tie wrap which securely holds the
four (4) latches of the subwoofer;

2. Lift each of the latch’s handles, then twist
counterclockwise 180 degrees and pull to release;

3. Completely open and remove the upper shell of the flight
case;

4. Remove the power cord located inside the port;

5. Place the hands under the central section of the cabinet.
Lift the section and carefully lay it on the base of the flight
case;

6. Turn the subwoofer over on one speaker side;

7. Assemble the four (4) spike locking nuts with the four (4)
threaded spikes. Leave approximately half an inch
between the tip end and the nut;

8. Move the subwoofer back on its spikes;

9. Connect the power cord to the subwoofer and to the wall
outlet;

10. Connect the signal output to the selected Rocco input
panel. Adjust the subwoofer position and the control for
the best result. (See the owner’s manuaal for detailed
information.) This adjustment should be done without the
grilles and glass;

11. Place the nine (9) sorbothane bumpers on the Rocco
active subwoofer. Make a 3 X 3 array. Remove the
hardened glass at the bottom of the fight case and
carefully place it on the sorbothane bumpers;

12. Attach the grilles on each side;

13. Place unused accessories inside the fligh case and store it
away.

2004.06.30

Tel: [phone]
Fax: [phone]

www.verityaudio.com

[e-mail]

1005 Saint-Jean-Baptiste, Suite 150
Quebec, QC G2E 5L1 Canada

ROCCO

Product Packing Instructions

The complete packaging should include:

i. (1) ATA approved flight case;
ii. (2) Accessory boxes;
iii. (1) Package containing the owner's manual.

One accessory box contains :

i. (4) Threaded spikes;
ii. (4) Threaded spikes locking nuts.

The other accessory box contains :

i. (9) Sorbothane bumpers.

WARNING: The Rocco’s module and its packaging are big and
heavy. Any operations that ask for moving, lifting or tilting will
require the assistance of a second person. Attempting to do it
alone could be hazardous, create injuries or permanent
damage to the loudspeaker.

1. Turn off all audio and video equipment. Remove the
power cord and all the interconnects signal input cable
from the Rocco active subwoofer input. The power cord
can be stored inside the port;

2. Temporarily remove the subwoofer grilles;

3. Remove the glass and place it at the bottom of the flight
case;

4. Remove the nine (9) sorbothane bumpers and store them
in one accessory box;

5. Turn the subwoofer over on one speaker side. You should
do it on a soft surface (a clean carpet or a big cotton
cloth);

6. Remove the four (4) spike locking nuts and the four (4)
threaded spikes. Store them inside the other accessory
box;

7. Place the subwoofer back on its upright position;

8. Place the hands under the central section of the cabinet.
Lift the section and carefully lay it on the base of the flight
case;

9. Reinstall the two (2) speaker grilles;

10. Store the accessory boxes and the owner's manual inside
the provided space;

11. Carefully install the upper shell of the flight case by
matching the two black pop rivets;

12. Secure the cover in place by closing the four (4) latches.

Locking the latches with tie wraps is highly
recommended;

13. The Rocco active subwoofer is ready to be labeled and
shipped.

2004.06.30

Tel: [phone]
Fax: [phone]

www.verityaudio.com

[e-mail]