VERITAS T-302, T-602, T-1002, T-2001, T-3001 Instruction Manual

SPECIFICATIONS

Model number Capacity Division

T 302 300g 0.01g

T -602 600g 0.01g
T -1002 1000g 0.01g
T -2001 2000g 0.1g
T -3001 3000g 0.1g
T -5201 5200g 0.1g

Platter 136x140mm

Net/gross weight 3.5lb/4.5lb

Package

Standard carton: 33.5×23×14(cm

3

)

6 Units in one box: 48.5×39.5×46(cm

3

)

Operating Temperature

0-40℃(32-104℉)

Power source

6XAAor AC/DC

Adapter 12V/500mA

ERROR CODE

COMPACT SCALE

/BALANCE

INSTRUCTION MANUAL

Error
Code

Reason Trouble Shooting

Err-O Overload Use within capacity.
Err-Z 1).Exceeded the zero

tracking range when
powering on.

2).Forgot to install pan
when performing
linearity calibration.

1). Pan should be empty on power up.
Remove any weight from pan.

2). Install pan and then recalibrate scale
（linearity calibration）.

Err-S Inner code unstable

when powering on.

1) Make sure the scale is stable when
powering on.

2) Low battery , ch a ng e or cha rg e ba tter y.

3) Allow for longer warm up period.

Err-L Calibrating without a

weight or the weight
is not the correct value.

Place a calibration weight of the value
shown on the display and then press
calibration button.

Err-P Counting setting error. Place the correct size parts sample when

setting up counting mode.

SAFETY PRECAUTIONS

All safety messages are identified by the following the words "WARNING" and
"CAUTION". These words mean the following:

△WARNING

Important information to alert you to a situation that
might cause serious injury and damage to your
property if instructions are not followed.

△CAUTION

Important information that tells how to prevent damage
to equipment.

When using the scale/balance, the following safety precautions should always be

followed.

△ WARNING

Use only the AC adaptor with the scale/balance. Other adaptor may cause
damage. (AC adaptor is optional)

△ CAUTION

 Avoid installing the scale/balance in direct sunlight, this may cause

discoloration or malfunctions.

 Keep scale at room temperature, away from heat sources.

 Avoid shock impact and loading over capacity. Do not keep heavy object

permanently on the platform.

 If scale is not used for an extended period, keep it clean and stored in

plastic package.

 Matter charged by static electricity will influence the weighing.

1

CALIBRATION

When to calibrate

1. Press [ON/OFF] to turn the power on for 15 minutes for warm up.

2. With scale turned off, press [ON/OFF] to turn the power on.

3. Display will show flashing digits and then “--------”,

4. Press [ZERO], the display will show “CAL”.

5. Press [ZERO] again , the display will show “X0000 g” where X is the
flashing digit,

6. Press [UNIT] key to move the flashing digit to the right.

7. Press [PCS] key to increase the flashing digit. (X is the calibration
weight which can be set according to your requirement – we
recommend a minimum of 50% balance capacity).

8. Press the [ZERO] key, the display will show a series of digits known as
the A/D value, these numbers will continuously move, once the display
shows the stable indicator (please see page 16 for help locat ing the
stable indicator), press the [UNIT] key, the display will then show --------,
then “X00.00” or “X000.0” depending on the model and capacity.

9. Place the calibration weight on the center of the platform.

10. Press [ZERO] key to return to weighing mode.

11. Now the Calibration is completed.

12. Press [ON/OFF] to turn off the power.

13. Press [ON/OFF] to turn on the power again.

14. Place the weight on the platform to make sure weighing is correct, if not,
repeat above steps.

6