Installation Guide
Temperature
TG
TD
NOTICE
• This product is not intended for life or safety applications.
• Do not install this product in hazardous or classied locations.
•
Read and understand the instructions before installing this product.
• Turn o all power supplying equipment before working on it.
• The installer is responsible for conformance to all applicable codes.
If this product is used in a manner not specied by the manufacturer, the protection
provided by the product may be impaired. No responsibility is assumed by the
manufacturer for any consequences arising out of the use of this material.
TD/TF/TG Series
TF
Product Overview
TD, TF, and TG temperature sensors monitor the temperature of the air inside a duct. The probe is available in
multiple lengths to suit multiple applications. All models have standard resistive outputs compatible with building
control systems, and all models are warranted for a period of ve years.
Product Identication
Enclosure Probe Length
T
D = Duct
F = Duct w/
mounting box
G = Duct w/ water
resistant housing
Duct Mounted Temperature Sensors
B = 4" (102 mm)
C = 6" (152 mm)
D = 8” (203 mm)
E = 12” (305 mm)
F = 18” (457 mm)
K = 36” (914 mm)
Sensor Type Output
RØ
B = 100R platinum, RTD
C = 1k platinum, RTD
D = 10k T2, Thermistor
E = 2.2k, Thermistor
F = 3k, Thermistor
H = 10k T3, Thermistor
I = 1k Balco (Nickel-iron) RTD
J = 10k Dale, Thermistor
K = 10k w/11k shunt, Thermistor
M = 20k NTC, Thermistor
N = 1800 ohm, Thermistor
T = 100k, Thermistor
W = 10k T2 high accuracy, Thermistor
Y = 10k T3 high accuracy, Thermistor
= Resistive
Cal Certificate
0 = None
2 = 3-point NIST calibration
TM
Specications
Wiring 22 AWG; 2-w ire RTD/Thermistor
Housing Stainl ess Steel
Mounting Location Not suitable f or wet locations. For ind oor use only.
WARRANTY
Limited Warranty 5 years
COMPLIANCE INFORMATION
Agency Approvals CE
Z205467-0F Page 1 of 2 0319
Find Quality Products Online at: sales@GlobalTestSupply.com
Alta Labs, E nercept, Ensp ector, Hawkeye, Trus tat, Aerospo nd, Veris, and th e Veris ‘V’ log o are tradema rks or regist ered tradem arks of Veris Ind ustries, L. L.C. in the USA and /or other count ries.
Other companies’ trademarks are hereby acknowledged to belong to their respective owners.
www.GlobalTestSupply.com
TD/TF/TG Series Installation Guide
TM
Dimensions
2"
(51 mm)
(74 mm)
2.9"
1.5"
(38 mm)
(18 mm)
0.7"
1.1"
(28 mm)
3.88”
(98.60 mm)
TD Model
TF Model
4.20”
(106.68 mm)
TG Model
0.25"Dia.
(6 mm)
L
Available in 4”, 6”,
12” and 18”
probe lengths
1.78”
(45.18mm)
Installation
Foam Gasket
2.5" x 2.5"
(64 mm x 64 mm)
4.6"
(117 mm)
2.0"
(51 mm)
L
0.25"Dia.
(6.3 mm)
1. Drill a 3/8” diameter hole into a duct for the sensor probe.
2. Insert the probe into the duct.
3. Secure the junction box housing (TF/TG) or the mounting ange (TD) to the outer surface of the duct using the self-tapping
screws provided.
4. Wire as shown.
Thermistor
RTD
Z205467-0F Page 2 of 2 0319
Alta Labs, E nercept, Ensp ector, Hawkeye, Trus tat, Aerospo nd, Veris, and th e Veris ‘V’ log o are tradema rks or regist ered tradem arks of Veris Ind ustries, L. L.C. in the USA and /or other count ries.
Find Quality Products Online at: sales@GlobalTestSupply.com
Other companies’ trademarks are hereby acknowledged to belong to their respective owners.
www.GlobalTestSupply.com
Loading...