Veris Industries HX30 SERIES, HX40 SERIES, HX50 SERIES Data Sheet

Minimize Installed Cost

Current Monitoring | Current Switches with Relay: Fixed Trip Point

HX30/40/50 SERIES

On/Off Status and Control in One Package

H730 H930

On/off status

On/off status and command relay
in a single labor and space saving
device

TM

Detect belt loss

Cost-effectively monitor start/stop,
unit vents, fan coils,
exhaust fans, and other loads
where belt loss is not a concern

SPDT command
relay

H740 and H940 feature a SPDT
command relay

No tubing
necessary

Easier to install than differential
pressure switches

Easy setup

No calibration required…easy
setup and operation

APPLICATIONS

Maximize Reliability

The Hawkeye Relay Combination Series combines an on/off status
sensor and command relay in one package, saving the labor, wire runs,
and space required to mount a separate relay. The switch and relay
(not electrically connected) are in the same housing, saving space and
cost. It is ideal for monitoring and controlling motors where belt loss is
not a concern.

SPECIFICATIONS

Sensor Power Induced from monitored conductor

Insulation Class 600 Vac RMS

Frequency Range 50/60 Hz

Temperature Range -15 to 60 °C (5 to 140 °F)

Humidity Range 10 to 90% RH non-condensing

Terminal Block Wire Size 24 to 14 AWG (0.2 to 2.1 mm2)

Terminal Block Torque 3.5 to 4.4 in-lbs (0.4 to 0.5 N-m)

WARRANTY

Limited Warranty 5 years

AGENCY APPROVALS

Agency Approvals

UL 508 open device listing, CAT III, Pollution
Degree 2, basic insulation

• Monitoring direct drive units,
exhaust fans, and other
fixed loads

RELAY CONTACT RATINGS

Hx30, Hx50 (SPST, N.O.)

Resistive 10 A @ 250 Vac, 30 Vdc

Inductive 5 A @ 250 Vac, 30 Vdc

Hx40 (SPDT)

Resistive 8 A @ 250 Vac, 30 Vdc

Inductive 3.5 A @ 250 Vac, 30 Vdc

TYPICAL COIL PERFORMANCE

Voltage AC DC

24V 10 mA 10 mA

Pull In Voltage

Hx30 20.1 Vdc

Hx40 20 .1 Vdc

Hx50 8.4 Vdc

Drop Out Voltage

Hx30 5.2 Vdc

Hx40 5.2 Vdc

Hx50 3.0 Vdc

• Monitoring on/off status of
electrical loads

• Starting/stopping motors

Note: Do not use the LED status indicators as evidence of applied voltage.

TM

HQ0001759.F 0117

Current Monitoring | Hx30/40/50 SeriesCurrent Monitoring | Current Switches with Relay: Fixed Trip Point

H730/740/750

Dimensional Drawing

Removable/Adjustable Mounting Bracket

0.9"

 0.7"

(19 mm)

4.2"

(106 mm)

2.8"

(68 mm)

3.8"

(95 mm)

0.2” x 0.15”
slot (2x)

* Terminal block may extend up to 1/8” over the height dimensions shown.
** Slide switch may extend up to 1/4” over the height dimensions shown.

(23 mm)

3.0" **

(75 mm)

1.1" *

(27 mm)

H930/940/950

Dimensional Drawing

Removable Mounting Bracket

Bracket can
be mounted
on three sides
for added
installation
flexibility.

3.1”**

(79 mm)

1.1”

(26 mm)

0.8”

(21 mm)

1.0”

(25 mm)

START/STOP MONITORING
OF FAN/PUMP MOTORS

Wiring Diagram

CONTACTOR

Motor

RELAY CONTROLLED DIREC TLY
BY STATUS CONTACTS

Wiring Diagram

Fan or Pump

CONTROLLER

Digital Output
(Relay Coil)

Digital Input
(Status)

CONTROL

POWER

Relay Coil
Power Source

Self-gripping Iris

2.8”

(70 mm)

Ø 0.3”

(8 mm)

2.5”

(64 mm)

3.0”

(76 mm)

* Terminal block may extend up to 1/8” over the height dimensions shown.

1.4”*

(36 mm)

RELAY LOAD

ORDERING INFORMATION

MODEL

H730 0.5 to 200 A

H740 0.5 to 200 A 0.5 A or less SPDT 24 Vac/d c Solid-core • •

H750 0.5 to 200 A 0.5 A or less SPST, N.O. 12 Vdc nom. Solid-core • •

H930 1.5 to 200 A 1.5 A or less SPST, N.O. 24 Vac/d c Split-core • •

H940 1.5 to 200 A 1.5 A or less SPDT 24 Vac/dc Split-core • •

H950 1.5 to 200 A 1.5 A or less SPS T, N.O. 12 Vdc nom. Split-core • •

AMPE RAG E

RANGE

STATUS OUTPUT

(MAX.)

N.O. 1.0 A @ 30 Vac/dc

TRIP

POINT

0.5 A or less SPST, N.O. 24 Vac/d c Solid-core • •

RE LAY

RE LAY

COIL

HOUSING

RE LAY

POWER LED

UL

HQ0001759.F 0117

TM