Veris Industries HX09 SERIES Data Sheet

SPECIFICATIONS

E150462

Current Monitoring | Adjustable Trip Point, High Voltage Output

HX09 SERIES

Detect Belt Loss, Coupling Shear,
and Mechanical Failure

H709

H809

Maximize Reliability

Minimize Installed Cost

H609

H909

Low setpoint

The H809 has a low (0.75 A)
minimum setpoint…no need for
multiple wraps of the conductor
through the sensor, even on loads
as small as 1/5 HP

Small in size

H609 and H809 are small in size
to fit easily inside small starter
enclosures

Versatility

Removable mounting bracket
optimizes field versatility

APPLICATIONS

• Detecting belt loss, coupling
shear, mechanical failure, and
interlocking loads

• Verifying lighting circuit and
other electrical service run
times

Adjustable trip
point

Precise current trip point setting

Status LEDs

For easy setup and local
indication

Flexibility

Bracket on H909 can be installed
in three different configurations

• Monitoring status of industrial
process equipment

• Monitoring status of critical
motors (compressor, fuel, etc.)

• VFD output On/Off status

• Fan/pump status monitoring

Hawkeye x09 Series are high performance current switches, ideal for line
voltage loads. The devices are powered by the current being monitored.
They are ideal for monitoring performance on unit vents, exhaust fans,
recirculation pumps, and other fixed loads.

Sensor Power Induced from monitored conductor

Insulation Class 600 Vac RMS (UL), 300 Vac RMS (CE1)

Frequency Range 50/60 Hz

Temperature Range -15 to 60 °C (5 to 140 °F)

Humidity Range 10 to 90% RH non-condensing

Hysteresis 10% (typical)

Terminal Block Wire Size 24 to 14 AWG (0.2 to 2.1 mm2)

Terminal Block Torque 3.5 to 4.4 in-lbs (0.4 to 0.5 N-m)

WARRANTY

Limited Warranty 5 years

AGENCY APPROVALS

Agency Approvals UL 508 open device listing; CE: EN61010-1,

CAT III, Pollution Degree 2, basic insulation

DETECTS BELT LOSS/COUPLING SHEAR!

DETECTS BELT LOSS/COUPLING SHEAR!

Fan/pump

Calibrated

Trip Point

O O

Now you can easily detect when drive belts slip, break, or pump couplings shear.
In fact, a typical HVAC motor that loses its load has a reduction of current draw
of up to 50%. That’s why our sensors are the industry standard for status.

1. The CE mark indicates RoHS2 compliance. Please refer to the CE Declaration of
Conformity for additional details.

Note: Do not use the LED status indicators as evidence of applied voltage.
If using this switch in an application that includes an electronically commutated motor
(ECM), see Veris Application Note VN61, at www.veris.com.

Loss of Belt/Coupling Shear

On

Electrical
Failure

TM

HQ0001755.G 0117

Current Monitoring | Hx09 Series

H609

Dimensional Drawing

Removable Mounting Bracket

0.6"

(16 mm)

2.1"

(54 mm)

0.4” x 0.2”

(10 mm x 5 mm)

Slot (2x)

H709/H709HV

Dimensional Drawing

Removable/Adjustable Mounting Bracket

 0.7"

(19 mm)

0.5"

(13 mm)

2.1"

(54 mm)

2.9"

(74 mm)

0.7"

(18 mm)

3.5"

(89 mm)

1.2"

(31 mm)

Self-gripping Iris

0.9"
(23 mm)

2.5" *

(64 mm)

1.0"

(26 mm)

3.0" **

(75 mm)

H809

Dimensional Drawing

Removable/Adjustable Mounting Bracket

 0.7"
(18 mm)

0.4” x 0.2”
Slot (x2)

H909/H909HV

Dimensional Drawing

Removable Mounting Bracket

1.1”

(26 mm)

3.1”**

(79 mm)

1.7

(43 mm)

2.3"

(58 mm)

0.8”

(21 mm)

1.0”

(25 mm)

0.9"

(23 mm)

1.1" *

(27 mm)

2.8" *

(71 mm)

Bracket can
be mounted
on three sides
for added
installation
flexibility.

MONITORING FAN /PUMP MOTORS
FOR POSITIVE PROOF OF FLOW

Wiring Diagram

CONTACTOR

9

Motor

CONTROLLER

Digital

Input

Fan or Pump

Self-gripping Iris

4.2"

(106 mm)

2.8"

(68 mm)

3.8"

(95 mm)

1.1" *

(27 mm)

Ø 0.3”

(8 mm)

(70 mm)

3.0”

(76 mm)

2.8”

2.5”

(64 mm)

1.4”*

(36 mm)

0.2” x 0.15”
slot (2x)

* Terminal block may extend up to 1/8” over the height dimensions shown.
** Slide switch may extend up to 1/4” over the height dimensions shown.

ORDERING INFORMATION

MODEL

H609 1.25 to 50 A N.O. 0.2 A @ 120 Vac/dc 1.25 A or less • Split-core

H709 1 to 135 A N.O. 0.2 A @ 120 Vac/dc 1.0 A or less • Solid-core •

H709HV 1 to 135 A N.O. 1.0 A @ 250 Vac 1.0 A or less Solid-core

H809 0.75 to 50 A N.O. 0.2A @ 120 Vac/dc 0.75 A or less

H909 2.5 to 135 A N.O. 0.2 A @ 120 Vac/dc 2.5 A or less • Split-core •

H909HV 2.5 to 135 A N.O. 1.0A @ 250 Vac 2.5 A or less Split-core

1. Listed for use on 75°C insulated conductors.

AMPERAGE RANGE

@ 50/60 H Z ONLY

STATUS OUTPUT

(MAX.)

MIN. TRIP

POINT

STAT US

LED

• Solid-core

HOUSING UL CE

LEAD

FREE

1

•

1

•

•

•

•

•

HQ0001755.G 0117

TM