Veris SD User Manual

QUICK START GUIDE

S D s e r i e s

SD – Spot Detector

1. Installation

Determine a location. Ram set 6/32 threaded studs in floor on 2.5 inch (63.5mm) centers. Place SD over studs and

secure. Adjust the sense probes to desired height. Connect the white/red and black leads to the FMS, F-Series or

LDRA6 panel. A 24VAC power supply is required for use with a Falcon RA1x2. Test the SD by placing water

under the sense probes.

24 VDC

( Polarity is

Not important )

NC Reset

Push Button

White/Red (+)

Black (-)

SD Diagram 1

EXTERNAL

TB1

VDC

+ -

TB2 Input 1-4

24VDC

Ch1

Ch2

Ch3

+ -

Black

+ -

Ch4 + -

+ +

+ -

White/Red

SD Diagram 2: Falcon Wiring

SD-Z – Zone Spot Detector

1. Installation

Determine a location. Ram set 6/32 threaded studs in floor on 2.5 inch (63.5mm) centers. Place SD-Z over studs

and secure. Adjust the sense probes to desired height. Connect the SD-Z to the LDZ control panel by connecting

the two cable connectors to SeaHawk Water Leak Detection Cable (SC), or SeaHawk Non-Sensing Cable (NSC), or

an end terminator (EOL) as shown in SD-Z Diagram 2. Test the SD-Z by placing water under the sense probes.

SD-Z simulates 50 feet (15.24m) of SC cable: 25 feet in and 25 feet out (7.62m in/out) from device.

SD-Z Diagram 1: Pins

S D S D - Z S D - R O 1

Once triggered, latches on, until

power is removed (VDC)

TB3 Input 5-8

Ch5

Ch6

+ -

Ch7 + -

EXTERNAL Ch8 + -

GND

- -

RELAY 1 NC NO C

TB4

RELAY 2 NC NO C

Specifications

SD-Z Diagram 2: Basic Installation Components

SD-RO1 – Spot Detector with Relay Output

1. Installation

Determine a location. Ram set 6/32 threaded studs in floor on 2.5 inch (63.5mm) centers. Place SD-RO1 over

studs and secure. Adjust the sense probes to desired height. Connect the white (N/O) and green (Com) or blue

(N/C) leads to the alarm device. Connect the black (-) and red (+) leads to the power source. Test the SD-RO1

by placing water under the sense probes.

24 VAC / DC

Reset Push Button

VDC applications only)

(Normally Closed

Red (+)

Black (-)

White (N.O .)

Green (Com )

Blue (N. C.)

Brown (Not Used )

SD-RO1 Diagram 1: Basic Wiring

Once triggered, latches on, until

power is removed (VDC)

Power SD, SDZ SDRO1

Outputs Solid State SD SDZ, SDRO1 Relay SD, SDZ SDRO1

Leader Cable (Non-sensing) Length SD, SDRO1 SDZ Connector SD, SDRO1 SDZ

Operating Environment Temperature Humidity Altitude

Storage Environment -4° to 158°F (-20° to 70°C)

Dimensions 1.55”W x 2.0”H x 1.0”D (39.37mmW x 50.8mmH x 25.4mmD)

Weight SD SDZ SDRO1

Certifications CE; RoHS compliant

N/A 24VAC/VDC ± 10%, 0.1A max.; requires power supply: WA-DC-24 or WA-DC-24-ST (not included)

12-36VAC @ 0.01A min., 0.1A max.; 18-36VDC @ 0.01A min., 0.1A max. N/A

N/A Dry Contact, Form C; 1A @ 24VDC, 0.5A resistive @ 120VAC

14ft (4.27m) 10in (0.25m); quantity 2

N/A 1 Male, 1 Female; 4 pin, 0.96in (24.38mm) diameter; connects to SeaHawk SC Cable or Non-Sensing Cable

32° to 122°F (0° to 50°C) 5% to 95% RH, non-condensing 15,000ft (4,572m) max.

4 oz. (113g) 3 oz. (85g) 7 oz. (198g)

S D S D - Z S D - R O 1

FORT COLLINS CO

970 484-6510

970 484-6650 FAX WWW.RLETECH.COM

lthough the information contained in this document is believed to be accurate and correct, RLE Technologies assumes no responsibility, and disclaims all liability, for any damages resulting from the use of this information or any error or omission in this document. RLE Technologies does not warrant, guarantee, or make any representations as to the performance, fitness for use, safety, or reliability of any existing or future wiring, equipment, additions or modifications to equipment, or any other component of the original or modified system.