Veris PW2 Installation Instructions

VERIS INDUSTRIES

™

environmental SenSorS

NOTICE

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classiﬁed locations.

• Read and understand the instructions before installing this product.

• Turn oﬀ all power supplying equipment before working on it.

• The installer is responsible for conformance to all applicable codes.

2.2"

(57 mm)

(102 mm)

5.8"

(147 mm)

LOW HIGH

WET DIFFERENTIAL PRESSURE

inStallation GUiDe

PW2 SerieS PW2 SerieS

Wet Media Diﬀerential Pressure Transducer

Installer's Speciﬁcations

Media Compatibility 17-4 PH stainless steel Input Power 12 to 24VDC, 29mA max.; loop powered Output 2-wire transmitter; 4-20mA (clipped and cappe d)

Pressure Ranges:

0-50 psi (0-3.45 bar) 5/10/25/50 psid (0-0.34/0.69/1.72/3.45 bar) 0-100 psi (0-6.89 bar) 10/20/50/100 psid (0-0.69/1.38/3.45/6.89 bar) 0-250 (0-17.24 bar) 25/50/125/250 psid (0-1.72/3.45/8.62/17.24 bar) Proof Pressure 2x max. F.S. range Burst Pre ssure 5x max. F.S. range Accuracy at 2 5°C* Ranges A, B, C: ±1% F.S.**

available

Range D: ±2% F.S.** Surge Damping Electronic; 5-second averaging Temperature Compensated Range 0° to 50°C (32° to 122°F); TC Zero <1.5% of product F.S. per sensor; TC Span <1.5% of product F.S. per sensor Sensor Operating Range -20° to 85°C (-4° to 185°F) Long Term Stability ±0.25% per year Zero Adjust Pushbutton auto-zero Operating Environment -10° to 55°C (14° to 131°F); 10-90% RH noncondensing Fittings 1/8” NPT female, stainless steel 17-4 PH Physical White powder-coated aluminum

ProDuct iDentification

Local Display

PW2

L = LCD Display

X = No Display

* IMPORTANT! Select operationa l range according to maximum gauge p ressure, NOT d iﬀerential pressure. Example: High gauge p ressure=90 psig, Select 100 psig model (04).

NIST

Operational Range

N = NIST

X = None

03 = 0-50 psig

04 = 0-100 psig

05 = 0-250 psig

US or EU

S = Standard

C = CE

Dimensions

To conform to EMC Standards, use shielded cabling. Technical information is avai lable from the factory on request o r on our website (www.veris.com/ce)

* Accuracy combines linearit y, hys teresis, and repeatabilit y. ** F.S. is deﬁned as full span of selected rang e in bidirectional mode.

The PW2 Series sensor is designed to accept high diﬀerential pressure. Install the sensor on a duct or pipe across a pump, ﬁlter, heat exchanger, compressor, or other non-corrosive wet media. The dual sensor design eliminates the need for a bypass valve, and the bi-directional capability reduces installation errors. A pushbutton allows easy zero adjustment.

quick install

Mount sensor on a duct or pipe, across the pump, ﬁlter, or other pressure 1.

diﬀerential.

Wire as shown (see page 2).2.

Conﬁgure the jumpers (see page 2).3.

Alta Labs, Enercep t, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘ V’ logo are trademark s or registered tradema rks of Veris Industries, L.L .C. in the USA and/or othe r countries.

VERIS INDUSTRIES

™

DIGITAL CONTROL

Digital Output

4-20mA IN

POWER SOURCE

12 to 24 VDC

Port Swap/Norm Bi-Dr/Normal Slow Avg/Fast Norm Analog Rev/Norm Bar/PSI

ZERO

A-High B-Mid High C-Mid Low D-Low

REMOTE

ZERO

4-20mA

Pressure Range

Settings

Polarity

Insensitive

Default Settings in bold. Insert jumper to activate other features.

Model PW2-03 PW2-04 PW2-05

100 250

B 25 50

125

C 10 20 50

5 10 25

Model PW2-03 PW2-04 PW2-05

3.45

6.89

17.24

1.72

3.45

8.62

0.69

1.38

3.45

0.34

0.69

1.72

Range (PSI)

Range (bar)

HI PORT

100 psi 100 psi 50 psi 50 psi 0 psi

LO PORT

0 psi 50 psi 50 psi 100 psi 100 psi

4-20mA

+100 psi +50 psi 0 psi

-50 psi

-100 psi

Bidirectional Operation

Input Conditions Result Outputs Read

20mA 16mA 12mA 8mA 4mA

Wiring

Note: Use of a

housing grounding

screw is required

for CE applications

PW2 SerieS

inStallation GUiDe

Output is mA only. Example: PW2-04

Optional: Connect Zero terminals to digital output (contact closure) of control system.

Caution: Zero input is for dry-contact only. Do not apply voltage to the Zero terminals.

configuration

Jumper Notes

Port Swap/Norm Reverses polarity of the pressure ports (i.e. makes the LO port

Bi-Dr/Normal Normal: 0 to F.S. pressure

Slow Avg/Fast Norm Slow mode provides 5 second averaging for surge damping.

Analog Rev/Norm Normal: output increases as pressure increases;

Bar/PSI Select output units.

oPeration

Auto-Zero: Press and hold the Zero button for 2 seconds or provide contact closure on the auxiliary ‘Remote Zero’ terminal to reset the output to zero pressure. To protect the device from accidental zeroing, this feature is only enabled when the detected pressure is within 5% of fac tory calibration.

Alta Labs, Enercep t, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘ V’ logo are trademark s or registered tradema rks of Veris Industries, L.L .C. in the USA and/or othe r countries.

operate as the HI port and vice versa); used when the sensor is incorrectly plumbed.

Bidirectional: -F.S. pressure to +F.S. pressure; output reads ½ when

pressure is zero.

Reverse: output is maximum when pressure diﬀerential is zero and

decreases as pressure increases.

Range: Use the Range switch to select F.S. diﬀerential pressure.