VF01
Dear Customer,
Thank you for purchasing the Verilux
®
Original Deluxe Natural
Spectrum® Floor Lamp. You have received a quality product,
backed by a three-year limited warranty. As a Verilux® customer,
your satisfaction means everything to us. We look forward to
serving you now and in the future.
Many other healthy lighting products are available
through our catalog and online. Please visit us on the web at
www.Verilux.com to learn about other great Verilux® products.
Have a Bright Day!
Nicholas Harmon
President and CEO
2
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Thank you for purchasing the Original Natural Spectrum
Please read the following safety information before using. To reduce the risk of
fi re, electrical shock, or injury to persons:
• Do NOT dismantle.
• Do NOT alter power cord.
• Turn off/unplug and allow to cool before replacing bulb or cleaning.
• For indoor use only.
• The lamp is an electrical device. DO NOT USE NEAR WATER
®
Deluxe Floor Lamp.
GENERAL PRECAUTIONS
• Before plugging in the lamp, check to make sure the voltage corresponds
with the main voltage of your location (120 volts).
• Do not use the lamp outside or in wet locations such as bathrooms. It is
intended for indoor, dry use only.
• Not for use with light dimmers, timers, motion detectors or extension cords.
• This product may cause interference with radios, cordless telephones,
or devices that use a wireless remote control, such as televisions. If
interference occurs, move the product away from the device, plug the
product or device into a different outlet, or move the lamp out of the line of
sight of the remote control receiver.
• The light bulb may become loose during transit. To reinstall the light bulb,
see the bulb installation instructions on page 8.
• Do NOT use lubricating agent in assembly; please see troubleshooting
section if you are having diffi culty assembling your lamp.
• Unplug from electrical outlet for extended periods of non-use or during
lightning storms to ensure protection of the electronics.
3
Main Parts & Controls
A. Lamp Head
B. Gooseneck
C. Shaft
D. Lamp Base
E. Power Cord
Close-up of Lamp Head
GETTING STARTED
F. Polarized Plug
G. Parabolic Grid Diffuser
H. Bulb
I. High/Off/Low Switch
A
H
G
Attention!
DO lift your lamp by the shaft. DO NOT lift the lamp by the gooseneck.
I
B
C
D
E
F
4
UNPACKING YOUR LAMP
1. Remove all pieces from box.
Locate 2 screws and tightening tool.
2. Detach red plastic pieces and store them in the event you need to
return the lamp.
3. Important: To avoid scratching the metal shaft, do not use a sharp
object to cut the plastic covering. The clear plastic covering on the
shaft is specially designed to tear away easily.
IMPORTANT NOTE:
Remove red plastic protective pieces prior to assembly.
5
ASSEMBLY INSTRUCTIONS
Read Instructions Carefully Before Assembly:
1. Remove lamp from box and packaging. Remove
red plastic protective pieces from lamp shaft.
NOTE: Please save original packaging for
repacking should you need to return the
product.
2. Set lamp base on the fl oor and insert
the lamp shaft over the base support
part until the screw holes line up as
shown in Fig.1. Insert the screw using
the tightening tool and turn clockwise to
tighten. We recommend assembling the
base fi rst before lamp head.
3. Attach the lamp head gooseneck to the
shaft, tucking the wire into the shaft, until
the screw holes line up as shown in Fig.1.
Insert the screw using the tightening tool
and turn clockwise to tighten. Should you
have diffi culty lining up the base or head
screw holes, refer to the troubleshooting
section of this manual.
Close-up of screw hole
in the lamp base
6
ASSEMBLY INSTRUCTIONS cont.
4. Attaching the Parabolic Grid Diffuser
• Remove grid diffuser from protective plastic bag
• Insert plastic pegs at bottom of grid diffuser into openings near bulb
socket
• Snap tab into place
5. Plug lamp into outlet and turn on; if bulb does not illuminate
instantly, please refer to the troubleshooting section of this manual.
7
Removal
BULB REPLACEMENT INSTRUCTIONS
1. Unplug lamp from power source.
2. To access to the bulb, remove grid
diffuser by depressing the tab and
lifting it out. (See page 7)
3. Firmly hold bulb base (B) and pull
bulb (C) from the socket (A) in
an outward motion.
Installation
1. Unplug lamp from power source.
2. Firmly hold base (B) and push bulb
(C) into the socket (A).
3. Be sure bulb is fi rmly seated in the
socket (see below) and snapped
into the metal bulb clip (D).
4. Replace grid diffuser.
YES NO
Fig. 10
A
A
B
B
C
C
No
gap
Correctly seated bulb Incorrectly seated bulb
large gap
8
Notice
TROUBLESHOOTING
Before Requesting Service on Your Verilux® Lamp, Please Read the
Following:
• Make sure all power connectors, cords, and plugs are inserted fully
and securely.
• Be sure the bulb is securely seated into the socket. (See page 8)
• Make sure there is power to the wall outlet or try another outlet.
9
CARE & CLEANING
Your lamp is made from high quality materials that will last for many
years with minimum care. You may want to periodically clean the lamp,
using a mild non-abrasive cleaner and soft cloth. When cleaning, make
sure you have turned off and unplugged the unit, and allowed suffi cient
time for the unit to cool. All liquid should be properly wiped away and
dried prior to restoring power.
DO NOT USE SOLVENTS OR CLEANERS CONTAINING
ABRASIVES, OR AMMONIA BASED CLEANERS
Note: All moisture should be properly wiped away and dried prior to
restoring power.
10
WARRANTY
Three-Year Limited Warranty
ATTENTION! ONCE OPENED, PLEASE DO NOT RETURN THIS PRODUCT TO THE
STORE WHERE IT WAS PURCHASED FOR REPAIR OR REPLACEMENT!
Many questions may be answered by visiting www.Verilux.com, or you may call our
customer service department at 1-888-544-4865.
This limited warranty is provided by:
Verilux, Inc., 340 Mad River Park, Waitsfi eld, VT 05673
Verilux® warrants this product to be free from defects in material and workmanship for a period of three years from
the date of the original retail purchase. During the limited warranty period, Verilux, Inc. will, at its option, repair or
replace defective parts of this product, at no charge to the customer, subject to the following limitations. This limited
warranty does not include any postage, freight, insurance or delivery fees. This warranty does not cover damage,
defect or failure caused by or resulting from accident, external destruction, alteration, modifi cation, abuse, misuse, or
misapplication of this product.
If, during the fi rst three years of ownership, this product fails to operate properly, it should be returned as
specifi ed below:
Please pack the defective product in its original protective packing and box, with a copy of your sales receipt, along
with $6.95 (check or money order to cover shipping and handling), and send to:
For U.S. Postal Service Only:
Verilux Warranty
Service Center, c/o WTB
P.O. Box 119, West Redding, CT 06896
32 Henry Street, Bldg 17A, Bethel, CT 06801
For Fed Ex & UPS Only:
Verilux Warranty
Service Center, c/o WTB
Please allow 4-6 weeks before you receive the repaired or replaced product.
ATTENTION: When returning a product, be aware that damage during shipping is the
responsibility of the purchaser and will void any warranty claim. We recommend that
you insure the shipment by shipper when returning this product or any parts. Be sure to
return product in original packaging.
Note: Verilux® recommends using a quality surge suppressor on all electronics equipment. Voltage variations
and spikes can damage electronic components in any system. A quality suppressor can eliminate the vast
majority of failures attributed to surges and may be purchased at electronics stores.
Due to ongoing improvements, actual product may have slight variations from the product described in this manual.
11
Please visit our web site at: www.Verilux.com
340 Mad River Park, Waitsfi eld, VT 05673
1-888-544-4865
VF01-MAN-Rev2
© Copyright 2007 Verilux, Inc. All rights reserved.
Printed in Taiwan for Verilux, Inc.
Loading...