VD03
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Thank you for purchasing the Heritage™ Natural Spectrum
Lamp. Please read the following safety information before using. To reduce the
risk of fi re, electrical shock, or injury to persons:
• Do NOT dismantle.
• Do NOT alter power cord.
• Turn off/unplug and allow to cool before replacing bulb or cleaning.
• For indoor use only.
• The lamp is an electrical device. DO NOT USE NEAR WATER
®
Deluxe Desk
GENERAL PRECAUTIONS
• Before plugging in the lamp, check to make sure the voltage corresponds
with the main voltage of your location (120 volts).
• Do not use the lamp outside or in wet locations such as bathrooms. It is
intended for indoor, dry use only.
• Not for use with light dimmers, timers, motion detectors or extension cords.
• This product may cause interference with radios, cordless telephones,
or devices that use a wireless remote control, such as televisions. If
interference occurs, move the product away from the device, plug the
product or device into a different outlet, or move the lamp out of the line of
sight of the remote control receiver.
• The light bulb may become loose during transit. To reinstall the light bulb,
see the bulb installation instructions on page 8.
• Do NOT use lubricating agent in assembly; please see troubleshooting
section if you are having diffi culty assembling your lamp.
• Unplug from electrical outlet during lightning storms to ensure protection of
the electronics.
3
Main Parts & Controls
GETTING STARTED
A. Lamp Head
B. Switch
C. Lamp Head Swivel Knob
D. Lamp Arm
E. Center Swivel Knob
F. Counter Weight Arm
A
Close-up of Lamp Head
G. Vertical Shaft
H. Lamp Base
I. Power Cord
J. Power Supply (Ballast)
K. Optix
®
Glare Control Filter
L. Bulb
C
D
E
L
B
G
F
H
I
J
A
4
ASSEMBLY INSTRUCTIONS
Please Read Operating Instructions Carefully Before Using the
Heritage™ Desk Lamp:
1. Set lamp base on the desk and insert the counter weight arm (F)
onto the center swivel (E) and screw clockwise to tighten. (Fig.1)
2. To lift lamp head, loosen swivel knob (C), adjust head to desired
angle. Tighten swivel knob.
3. Attaching the Optix
• Remove glare control fi lter from protective plastic bag. Take care
to hold fi lter by the edges only.
• Insert tabs on bottom of fi lter into opening. (Fig. 2)
• Press into place using thumb tab.
Do not touch or press on the fi lter material itself.
®
glare control fi lter:
C
E
Fig. 1
F
Note: Do not
touch material
Fig. 2
5
ASSEMBLY INSTRUCTIONS cont.
4. Attach the ballast to the power
cord. Use care to align the 4-pin
plug properly. DO NOT FORCE
– the 4-pin plug was designed to
fi t in only one orientation. (Fig. 3)
5. Plug ballast into a standard 120V 50/60Hz
outlet. Turn lamp on. The green LED indicator
on center of the ballast should be illuminated.
(Fig. 4) If the LED indicator does not illuminate,
please refer to the troubleshooting section of
this manual. (See page 9)
6. If bulb does not illuminate instantly, please refer
to the troubleshooting section of this manual.
7. Adjust lamp brightness to the desired level (lowmedium-high).
Fig. 3
WARNING: Do not block vents on ballast. Vents
are necessary for proper function of the ballast;
blocking them may cause overheating of the
ballast and increase risk of fi re.
Attention!
Lift your lamp by the vertical shaft.
6
Vents
Fig. 4
ADJUSTING THE HERITAGE DESK LAMP
The Heritage™ Desk Lamp
adjusts several ways:
1. To adjust lamp height – hold lamp
arm with one hand, loosen center
swivel knob (E). Raise or lower lamp
arm (D) to desired height. Tighten
knob. (Fig. 5)
2. To adjust lamp head angle up
or down – loosen swivel knob
counterclockwise, place head at
desired angle, tighten swivel knob to
secure. (Fig. 6)
D
E
Fig.5
Swivel
Knob
Fig. 6
3. To tilt lamp head toward you or
away from you – simply move
head to desired position. (Fig. 7)
Fig. 7
7
BULB REPLACEMENT INSTRUCTIONS
Removal
1. Unplug lamp from power source.
2. To access the bulb, remove Optix
glare control fi lter by depressing the
thumb tab and lifting it out.
3. Firmly hold bulb base (B) and pull
bulb (C) from the socket (A) in an
outward motion. (Fig. 8)
Installation
1. Unplug lamp from power source.
2. Firmly hold base (B) and push bulb
(C) into the socket (A).
3. Be sure bulb is fi rmly seated in the
socket (see below) and snapped
into the metal bulb clip (D). (Fig. 9)
4. Replace Optix® glare control fi lter.
®
YES NO
No
gap
Notice
large gap
Correctly seated bulb Incorrectly seated bulb
8
TROUBLESHOOTING
Your Verilux® desk lamp uses advanced micro-electronics to power
the revolutionary Trucolite™ bulb. These electronics are housed in a
specially designed ballast located at the power plug. The LED indicator
light on the ballast allows you to troubleshoot any problems with the
lamp’s function. When replacing your Verilux
in the power cord properly. The 4-pin plug was designed to fi t in only
one orientation (See Assembly Instructions on page 5).
®
ballast, take care to plug
Before requesting service on your Verilux
®
lamp, please check the
following:
• Make sure all power connectors, cords, and plugs are inserted fully
and securely.
• Be sure the bulb is securely seated into the socket. (See page 8).
• Unplug the lamp for a few minutes (this allows the electronics in the
ballast to reset).
• Make sure there is power to the wall outlet or try another outlet.
WARNING: Do not block vents on ballast. Vents are necessary for
proper function of the ballast; blocking them may cause overheating of
the ballast and increase risk of fi re.
9
CARE & CLEANING
Your desk lamp is made from high quality materials that will last for
many years with minimum care. You may want to periodically clean the
lamp, using a mild non-abrasive cleaner and soft cloth. When cleaning,
make sure you have turned off and unplugged the unit, and allowed
suffi cient time for the unit to cool. All liquid should be properly wiped
away and dried prior to restoring power.
DO NOT USE SOLVENTS OR CLEANERS CONTAINING
ABRASIVES, OR AMMONIA BASED CLEANERS
Note: Do not use any cleaning agents, including window cleaner, on the
Optix glare control fi lter. If needed, dust with a clean, dry cloth.
10
Please visit our web site at: www.Verilux.com
340 Mad River Park, Waitsfi eld, VT 05673
1-888-544-4865
VD09-MAN-Rev3
© Copyright 2008 Verilux, Inc. All rights reserved.
Printed in China for Verilux, Inc.
Loading...