Verilink 5650 User Manual

i

WANsuite® 5650
Reference Manual

May 2002
34-00314.E

ii

WANsuite 5650

Copyright Notice

Copyright © 2002 Verilink Corporation. All rights reserved. No part of this publication may be

reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language

in any form by any means without the written permission of Verilink.

Manual Reorder # 34-00314.E

May 2002

Verilink® and WANsuite® are registered trademarks of Verilink Corporation. FrameStart™ and

ServiceAware™ are trademarks of Verilink Corporation.

All other brand and pr oduct nam es used herei n are trademark s or registe red trademarks of their

respective manufacturers.

This document doe s no t c reat e any ex pre ss or imp l ied war ra nt y a bout Verilink or about its prod-

ucts or services. The end-user documentation is shipped with Verilink’s products. Verilink has

made reasonable efforts to verify that the information contained herein is accurate, but Verilink

assumes no responsibility for its use or for any infringement of patents or other rights of third

parties that may result. The customer is solely responsible for verifying the suitability of Ver-

ilink’s products for its use. Specifications are subject to change without notice.

Verilink’s policy for product returns is provided in the Preface of this document.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to EN 55 022. Th ese li mits a re d esig ned to pr ovid e reaso nab le prote ction ag ainst ha rm-

ful interference when the eq uipment is operated in a commercial environ ment. This equipment

generates, uses, and can radiat e radio frequency energy and if not installed and use d in accor-

dance with the instruction manual, may cause harmful interference to radio communications.

This device must also acc ept any interference received, in cluding interference that may cause

undesired operation.

W ARNING:

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital

apparatus set out in the Rad i o In ter feren ce Regu lat ions o f t he C an adian D epart ment of Co mmu -

nications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites appli-

cables aux appareils numériques (de la class B) prescrites dans le Règlement sur le brouillage

radioélectrique edi cté par le ministère des Communications du Cana da.

When handling this equipmen t, follow t hese basi c safety pr ecautions t o reduce the risk of elec-

tric shock and injury:

•

Follow all warnings and instructions marked on the product and in the manual.

•

Unplug the hardware from t he wall outlet before cleaning. Do not use liquid cleaners or

aerosol cleaners. Use a slightly damp cloth for cleaning.

•

Do not place this product on an unstable cart, stand, or table. It may fall, causing serious

damage to the pro duct.This produc t should be operat ed only fr om the ty pe of power so urce

indicated on the mark ing label and manual. If you ar e unsure of the type of power supply

you are using, consult your dealer or local power company.

•

Do not allow anything to rest on the power cord. Do not locate this product where the cord

interferes with the f re e mo ve m e nt of pe op le .

•

Do not overload wall outlets and extension cords, as this can result in fire or electric shock.

•

Never push objects of any kind into the unit. They may touch dangerous voltage points or

short out parts that could result in fire or electric shock. Never spill liquid of any kind on

this equipment.

•

Unplug the equipment from the wall outlet and re fer servicing to qualified service personnel

under the following conditions:

Trademarks

Documentation Disclaimer

Product Returns
Emissions

Requirements

Canadian Emissions Requirements

Safety Precaut ions

Changes or modifications to this unit not expressly approved by the party

responsible for complianc e could voi d the user ’s authority to operate the
equipment.

iii

When the power supply cord or plug is damaged or frayed.

If liquid has been spilled into the product.

If the product has been exposed to rain or water.

If the product has been d ropped or i f the hous ing has be en damaged.

Safety Certifications

IEC 60950 CB Scheme:

The WANsuite 5650 from Verilink was tested to the International

Electrotechnical Commissio n (IEC) CB Scheme (IEC 60950 ) which is recogn ized by more than

30 participating countries. This allows Verilink customers around the world to feel confident

that Verilink products comply with their relevant international standards.

•

•

•

•

iv

WANsuite 5650

v

Table of Contents

Preface

About this Manual

...............................................................................................................................

-ix

Manual Organization

.....................................................................................................................

-ix

Typographic Conventions

..............................................................................................................

-x

Customer Service and Technical Support

.............................................................................................

-x

Support from Your Network Supplier

............................................................................................

-x

Support from Verilink

....................................................................................................................

-x

Telephone

................................................................................................................................

-x

E-mail

................................................................................................................................

.....

-xi

Internet

................................................................................................................................

....

-xi

Returning a Unit to Verilin k

................................................................................................................

-xi

Chapter 1

About the WANsuite 5650

Introduction

................................................................................................................................

.........

1-1

Features of the WANsuite 5650

.........................................................................................................

1-1

Flexible Us er Interfaces

...............................................................................................................

1-1

Simple Installation, Management and Troubleshooting

..............................................................

1-2

Features Summary

..............................................................................................................................

1-2

Front Panel

................................................................................................................................

..........

1-3

Front Panel Buttons

......................................................................................................................

1-3

Port Select Button

..................................................................................................................

1-3

Local Loop/Error Inject Button

.............................................................................................

1-4

Remote Loop Button

.............................................................................................................

1-4

BERT Button

.........................................................................................................................

1-4

LED Indicators

.............................................................................................................................

1-4

Rear Panel Connections

......................................................................................................................

1-6

Power Connection

.......................................................................................................................

1-6

Power Failure

.........................................................................................................................

1-6

Supervisory Port

...........................................................................................................................

1-7

Serial Interface

.............................................................................................................................

1-7

G.703 Port

................................................................................................................................

....

1-7

SHDSL Port

................................................................................................................................

.

1-7

Chapter 2

Installation

Unpacking and Inspection

.................................................................................................................

2-1

Supplied Materials

..............................................................................................................................

2-1

vi

WANsuite 5650

Chapter 3

VT100 Interface

Introduction

................................................................................................................................

.........

3-1

Accessing the VT100 Interface

...................................................................................................

3-1

Screen Components

......................................................................................................................

3-1

Cursor Controls

............................................................................................................................

3-2

Field Types

................................................................................................................................

...

3-2

Main Menu and Menu Structure

..................................................................................................

3-3

System Screen

................................................................................................................................

.....

3-4

Download App Code

....................................................................................................................

3-5

Maintenance Reset--TDM

............................................................................................................

3-5

Save and Restart

...........................................................................................................................

3-6

Interfaces Screen

................................................................................................................................

.

3-7

SHDSL Screen

................................................................................................................................

....

3-7

Configuration Profiles Scree n

....................................................................................................

3-10

Configuration Detail s Scre en

...............................................................................................

3-10

Alarm Profiles Screen

................................................................................................................

3-12

Alarm Profi le Details Screen

...............................................................................................

3-13

Span Endpoints Screen

...............................................................................................................

3-14

Span Endpoint Details Screen

.............................................................................................

3-14

Span Endpoint Maintenance Screen

....................................................................................

3-16

Span Endpoint Performance Screen

....................................................................................

3-17

15-Minute and 1-Day Intervals Screens

..............................................................................

3-18

G.703 Screen

................................................................................................................................

.....

3-18

Serial Screen

................................................................................................................................

.....

3-23

Supervisory Screen

...........................................................................................................................

3-27

Service Table Screen

........................................................................................................................

3-28

Service Details Screen

................................................................................................................

3-29

TDM Service Details Screen

......................................................................................................

3-30

Applications

................................................................................................................................

......

3-31

Diagnostics Screen

.....................................................................................................................

3-31

Test Details Screen

..............................................................................................................

3-31

Trap Log Screen

.........................................................................................................................

3-32

Chapter 4

Front Panel Interface

Introduction

................................................................................................................................

.........

4-1

Description of Front Panel

...........................................................................................................

4-1

Front Panel Buttons

............................................................................................................................

4-1

Port Select Button

........................................................................................................................

4-1

Local Loop/Error Inject Button

....................................................................................................

4-2

Remote Loop Button

....................................................................................................................

4-2

BERT Button

................................................................................................................................

4-2

LED Indicators

................................................................................................................................

....

4-3

vii

Appendix A

Specifications

Data Interfaces

................................................................................................................................

...

A-1

SHDSL Port

................................................................................................................................

A-1

G.703 Port

................................................................................................................................

...

A-1

Serial Interface

............................................................................................................................

A-1

Management Interfaces

......................................................................................................................

A-1

EOC (Embedded Operations Channel)

.......................................................................................

A-1

Supervisory Port

..........................................................................................................................

A-2

Power

................................................................................................................................

.................

A-2

Mechanical

................................................................................................................................

.........

A-2

Environmental

................................................................................................................................

....

A-2

Alarms

................................................................................................................................

................

A-2

Industry Listings

................................................................................................................................

A-2

Diagnostics

................................................................................................................................

........

A-2

Ordering Information

.........................................................................................................................

A-6

Optional Equipment

...........................................................................................................................

A-6

Connector Pin Assignments

...............................................................................................................

A-7

Serial Interface Pin Assignmen ts (DCE Mode)

..........................................................................

A-7

SHDSL Interface Pin Assignments

.............................................................................................

A-8

G.703 Connector Pin Assignments

.............................................................................................

A-8

Supervisory Port Pin Assignments

..............................................................................................

A-8

viii

WANsuite 5650

About this Manual

This reference guide for the Verilink WANsuite 5650 network termination unit
(NTU) describes unit features and specifications, configuration, and cabling. It

not

is

a users guide containing step-by-step procedures. Rather, this manual is
designed to be used as a reference regarding commands, interface ports,
configuration parameters, and other specific information about the Verilink
WANsuite 5650 unit.

Manual Organization

The chapters and appendices in this manual are arranged for quick reference
when you need it. You do not have to read previous chapters to understand
the subsequent chapters. Appendices are designed to complement the main
chapters.

Chapter 1, About the WANsuite 5650

•

features and capabiliti es.

Chapter 2, Installation

•

powering information.

C

– This chapter describes product

– This chapter descri bes unit port connections and

REFACE

0

P

HAPTER

Chapter 3, VT100 Interface

•

configuration parameters accessed through the VT100 interface.

Chapter 4, Front Panel Interface

•

indicators and control buttons associated with the WANsuite 5650’s front
panel interface.

Appendix A, Specifications

•

WANsuite 5650. In additi on, this section pr ovide s order ing inf ormati on (par t
numbers) and all th e co nnecto r pin a ssignmen ts for the i nte rfac es on th e back
of the WANsuite 5650 unit.

−

This chapter describes the menu screens and

−

This chapter describes the LED status

– This appendix defines the spec if ications for the

Preface ix

Typographic Conventions

The following table lists the graphic conventions used throughout this guide.

Verilink provides easy access to customer support information through a

variety of services. This section describes these services.

If assistance is required, contact your network supplier. Many suppliers are

authorized Verilink service partners who are qualified to provide a variety of

services, including network planning, installation, hardware maintenance,

application training, and support services. When you contact your network

supplier for assistance, have the following information ready:

Diagnostic error messages

A list of system hardware and software, including revision levels

Details about recent configuration changes, if applicable

If you are unable to receive support from your network supplier or want to

contact us directly, Verilink offers worldwide customer support by telephone,

e-mail, and through Verilink’s Internet Web site.

Customer support is available by telephone 24 hours a day, seven days a

week. To speak directly with a Verilink customer service representative, you

may dial one of the following toll-free numbers:

Sales and Marketing:

800-VERILINK (837-4546)

Technical Support

:

800 -285-2755

Convention

Description

A

calls attention to important features or instructions.

A

alerts you to serious risk of data loss or other

results that may cause you or the unit trouble if the warning

is not heeded.

A

alerts you to the risk of serious damage to the

unit or injury and possible death to the end user.

Notice

Caution

Warning

Customer Service and Technical Support

Support from Your Network Supplier

•

•

•

Support from Verilink

Telephone

•

•

x WANsuite 5650

If these toll-free numbers are not supported in your dialing area, you may call

Verilink by direct dialing 1-256-327-2001.

E-mail

You can request sales and marketing information or pose a technical support

question about your Verilink product by contacting us at the e-mail addresses

provided below. Verilink will respond to e-mailed requests for support during

regular business hours (8

A.M

.

–5 P.M.

CST, Monday–Friday) .

Sales and Marketing: [e-mail]

Technical Support: [e-mail]

Access the lat est networki ng informati on on Veril ink’s Internet Web site by

entering our URL into your Internet browser:

http://www.verilink.com/

This service features information about Verilink products, customer service,

technical support, latest news releases, and more.

If for any reason the Buyer must return a Verilink product, it must be returned

to the factor y, shipping prepaid, and pac kage d to the be st comm ercial s tanda rd

for electronic equipment. Verilink will pay shipping charges for delivery on

return. The Buyer is responsible for mode and cost of shipm ent to Verilink.

The Buyer mus t have a Retu rn Mate rial Aut horiza tion (RMA ) numbe r marked

on the shipping package. Products sent to Verilink without RMA numbers will

be returned to the sender, unopened, at the sender's expense.

A product sen t directly to Verilink for r epair must fi rst be assigne d a Return

Material Authorization (RMA) number. The Buyer may obtain an RMA

number by calling the Verilink Customer Service Center at 1.800.926.0085,

extension 2282 or 2322. When calling Verilink for an RMA, the Buyer

should have the following information available:

Model number and serial number for each unit

Reason for return and sympto ms of problem

Purchase order number

Name and phone number of person to contact if Verilink has questions

about the unit(s).

A return address will be provided at the time the RMA number is issued. The

standard delivery method for return shipments is Standard Ground for

domestic returns and International Economy for international returns (unless

otherwise specified).

•

•

Internet

Returning a Unit to Verilink

•

•

•

•

Preface xi

xii WANsuite 5650

C

HAPTE

R

1

C

Verilink’s

WANsuite 5650

High Speed Network Interface –

BOUT THE

1

A

HAPTER

Introduction

The telecommunications network service m arket is rapidly changing, where
network monitoring, control, and higher performance in packet processing are
not only expected, but demanded, at competitive price points.

is a feature-r ich network t ermination u nit (NTU) for
managing multiple applications and m ixed-mode packet-based services −
including high-speed Internet access − at price points expected of single­function devices.

The WANsuite 5650 is a G.shdsl/TDM network termination unit (NTU)
equipped with a network port, an asynchronous supervisory port, a user­selectable multi-protocol serial interface, a G.703 port, nine status LEDs, and
four input control buttons.

Features of the WANsuite 5650

Subscriber Line) provides synchronous line rates that will adapt from

2.312 Mbps to 192 kbps. Its spectral compatibility with other DSL services
and extended reach and rate capabilities make G.shdsl the preferable
broadband service delivery mechanism over copper lines for today's service
provider. By extending the addressable market, more end users than ever
before will now be able to obtain true broadband services.

WAN

G.shdsl (Single pair, High-spe ed Digi tal

SUITE

5650

Flexible User Interfaces

The WANsuite 5650 is equipped with two end-user interfaces: a multi­protocol DCE port and a G.703 port. The multi-protocol serial interface can
be easily set by the end user for V.35, V.36, or X.21 to meet your specific
data communications needs. The G.703 port provides you up to 2.048 Mbps
(E1) of bandwidth for your telecommunications equipment. Maximum

About the WANsuite 5650 1-1

flexibility or utilization of the SHDSL pipe is achieved by allowing for the

assignment of the individual timeslots to the desired end-user port.

Simple Installation, Management and Troubleshooting

The WANsuite 5650 has been designed for simple installation, management

and troubleshooting. Power and communications interfaces are easily

accessed on the rear panel. The nine tri-color LEDs on the front panel

provide quick and easily recognizable status indications of unit operation.

The WANsuite 5650 supports the full set of standard EOC commands

allowing for remote management of the NTU from the DSLAM/switch. The

local supervisory port can also be utilized for management of the unit in

conjunction with a comprehensive set of VT100 screens. The four input

control buttons on the front panel of the WANsuite 5650 provide a simplified

means of troubleshooting by accessing unit diagnostic loops.

A powerful core architecture

Three data ports: SHDSL, G.703/704, and multi-protocol

x64k

SHDSL WAN interface

Multi-protocol

x64k serial port soft ware-configurable for V.35, V.36 or

X.21

PowerPC™ platform with 8 Mbytes of RAM

G.703 port supports framed and unframed modes

HDB3 and AMI line coding

A suite of performance monitoring tools

Fully supports standard EOC commands

Local management port for on-site management, monitoring and

troubleshooting

Nine LED status indicators

Front panel control buttons to simplify troubleshooting

Programmable alarm thresholds

Features Summary

•

•

•

•

•

•

•

N

N

•

•

•

•

•

•

1-2 WANsuite 5650

Front Pane l

The front panel of the WANsuite 5650 has four user-activated input control

buttons and nine LED status indicators that provide access to unit diagnostics

loops for the data ports.

The following sections describe the functions of the LED indicators and the

control buttons.

The WANsuite 5650’s front panel control buttons are described in the

following paragraphs.

The WANsuite 5650’s ports are defined as SHDSL, G.703, and (serial)

x64k

port interfaces. The

PORT SELECT

button is used to cycle through and select

from the available ports. When a particular port is selected using the

PORT

SELECT

button, the port’s corresponding LED will flash. The status of the

LLOOP

, and

RLOOP

LEDs will be the summary of the test states for the port

interfaces.

The

PORT SELECT

button cycles through the following port options on each

successive press:

No port selection

Nx64k (serial interface) port

G.703 port

SHDSL port

When the

Nx64k (serial interface)

port is selected, the LED labeled

Nx64

flashes as an indication. The

LOCAL LOOP/ERR INJ

and

REMOTE LOOP

buttons

Figure 1.1

Front Panel Buttons

Port Select Button

Front Panel of WANsuite 5650

N

NOTICE:

When PORT SELECT is set to "No Selection" (as indicated by no
flashing port LEDs), the LLOOP, RLOOP and BERT buttons are
disabled.

•

•

•

•

About the WANsuite 5650 1-3

initiate/terminate tests and the corresponding LEDs indicate the status of tests

on this port only.

When on the G.703 port selection, the

G.703

port LED flashes as an

indication. If there is only a single service on the G.703 port then the

LOCAL

LOOP/ERR INJ

and

REMOTE LOOP

buttons initiate/terminate tests and the

corresponding LEDs indicate the status of tests on this port only.

When on the SHDSL port selection, the

SHDSL

port LED flas hes as an

indication. The

LOCAL LOOP/ERR INJ

and

REMOTE LOO P

buttons initiate/

terminate tests and the corresponding LEDs indicate the status of test s on this

port only. These tests are on the aggregate SHDSL payload.

The

REMOTE LO OP

button will invoke a G.SHDSL Network Side Transparent

Loop (see fi gure A.1).

Either the G.703 port or the Serial interface Nx64 will have transparent loop

with the

LOCAL LOO P

button (see figure A.2 or figure A.3).

Default: E nabled.

Default: E nabled.

Default: E nabled.

LED Indicators

The table below describes the WANsuite 5650’s front panel LED indicators.

SHDSL

G.703

Nx64

Nx64

G.703

SHDSL

NOTICE:

PORT SELECT will not operate if any l ocally initiated tests are in
progress.

Local Loop/Error Inject Button

Remote Loop Button

BERT Button

NOTICE:

NOTICE:

NOTICE:

1-4 WANsuite 5650

The
port select button

When no port is selected (indicated by none of the port LEDs flashing),
only the PORT SELECT button is enabled.

When no port is selected, the LL and RL LEDs display a summation of
the test states of the

,

, and

(serial interface),

port LEDs will flash when selected by the

, and

ports.

Table 1.1

LED Label

Off

Green

Amber

Red

POWER

No Power

Power applied to unit

Unit in test mode.

SHDSL

Mains Power Off

Trained with good

signal quality

Trained with marginal

signal quality

Training or attempting

to train with poor

signal quality and/or a

major network port

alarm is active

G.703

Service not configured

Service configured and

interface is operating

normally

Service is configured

and has minor alarms:

RAI; Slip

Service configured and

interface is not

operating normally:

LOS; LOA; AIS.

Nx64

Service not configured

Service configured and

interface is operating

normally

Service configured and

interface is not

operating normally or

port mismatch

RTS/C

Nx64k service not

configured

RTS/C

control line is OFF

"RTS" or "C" control

line (from DTE) is ON

RLSD/I

Nx64k service not

configured

RLSD/I

control line is OFF

"RLSD" or "I" control

line (from DTE) is ON

LLoop

No loop present

A local loop is active

on the selected

customer port

(button controlled)

A local loop is active on

the selected customer

port

A local loop is active

on the SHDSL port

RLoop

No loop present

A remote loop is active

on the selected

customer port

(button controlled)

A remote loop is active

on the selected

customer port

A remote loop is active

on the SHDSL port

BERT

not applicable

not applicable

not applicable

not applicable

LED Indicators

or

or

About the WANsuite 5650 1-5

Rear Panel Connections

The rear panel of the WANsuite 5650 has five connectors. From left to right

(as shown in Figure 1.2 below) these connectors are the power port,

supervisory port, serial interface (Nx64k), G.703 port, and SHDSL port. The

connectors are described in detail in the following paragraphs.

The

POWER

port

is a standard grounded three-prong connector. This 100-240

VAC power receptacle is rated at 47–63 Hz. To apply power to the unit,

simply plug the supplied power cord into the unit’s

POWER

port and then

connect the wall plug to an appropriate electrical outlet. The unit has no

power switch.

When power is applied to the unit, the front panel indicators flash for

approximately 10 to 15 seconds as the unit initializes. The green

POWER

LED on the front panel will remain illuminated as long as the unit receives

power. This LED turns amber when the unit is in test mode.

If the

POWER

indicator does not illuminate, check the power connections and

the primary A C circuit brea ker.

The WANsuite 5650 provides nonvolatile memory retention of the unit

configuration in case of a power failure. This feature allows the unit to

automatically restore normal service following a power loss.

Figure 1.2

Power Connection

WANsuite 5650 Rear Panel

1-6 WANsuite 5650

CAUTION:

Always connect the power cord to a grounded electrical outlet.

Power Failure

NOTICE:

Because the WANsuite 5650 does not employ an internal battery or time
chip, the unit will not retain time and date information in the event of a
power failure. The unit marks time beginning at 00:00 with each power
cycle.

Supervisory Port

The

SUPERVISORY P ORT

is a DB-9 female DCE connector configured for 8

bits, no parity, and 1 stop bit. Bit rates are configured through the unit’s

VT100 interface. The Supervisory port speed can be set to 1200, 2400, 4800,

9600, 19200, 38400, 57600, or 115200 bps. The initial default rate of the

Supervisory port is 38400 bps.

On power-up, the Supervisory port sends out diagnostic messages at the bit

rate of 115.2 kbps until the supervisory service acquires the Supervisory port,

after which the port speed is changed to the setting in the Supervisory

interface screen.

The

SERIAL INTERFACE

located on the rear of the WANsuite 5650 is a multi-

protocol interface presented physically as a DB-25 connection. The protocols

supported by this inte rface are V.35, V.36, and X.21.

Cables that adapt the DB-25 interface to the 34-pin V.35 interface are

available. These cables are optional equipment and their part numbers are

listed in

on page A-6. DB-25-to-DB-25 cables are also

available if your installation requires them. Refer to

on

page A-6 for details. Pin assignments for the serial interface are also listed in

Appendix A, "

.

FC C rule s requ ire tha t interco nn ectin g ca bles ca rryin g high -spe ed d ata

be appropriately shielded to minimize radio frequency interference.

The

G.703

port connection on the rear panel of the WANsuite 5650 is a

standard eight- pin modular jack with a receive signal level of -27 dB that

terminates a s 120 ohms. To view the pinout assignments for these interf aces,

refer to

on page A-8.

The

SHDSL

port connection on the rear panel of the WANsuite 5650 is a

standard eight- pin modular jack with a receive signal level of -24 dB that

terminates a s 135 ohms. To view the pinout assignments for this interfa ce,

refer to

on page A-8.

Serial Interface

G.703 Port

NOTICE:

Ordering Information

CAUTION:

For information on pinout assignments for this con nector, refer to
"Supervisory Port Pin Assignments" on page A-8. See "Ordering
Information" on page A-6 for information on cables for this connector.

Ordering Information

Specifications"

G.703 Connector Pin Assignments

SHDSL Port

SHDSL Interface Pin Assignments

About the WANsuite 5650 1-7

1-8 WANsuite 5650

C

HAPTE

R

2

This chapter describes the contents of your WANsuite 5650 shipment and
provides information on connecting and installing the unit.

Unpacking and Inspection

The WANsuite 5650 is shipped in cardboard cartons with foam inserts for
shock and vibration protection. When your shipment arrives, inspect the
shipping container and contents, and compare all items w ith those on the
packing list.

If the contents of the shipment are incomplete or if there is mechanical
damage or defect, notify Verilink. (Refer to
If the ship ping conta iner or c ushioning material is damage d, notify the carrie r
and Verilink immediately and make a notation on the delivery receipt that the
container was damaged. (If possible, obtain the signature and name of the
person making delivery.) Retain the packaging material until the contents of
the shipment have been checked for completeness and the unit has been
checked both mechanical ly and electric ally.

NSTALLATION

C

2

I

HAPTER

Support from Verilink

on page x.)

Supplied Materials

The WANs uite 5650 ship s with the follow ing standard items:

•

WANsuite 5650 unit

•

Power cable

•

Network cable

•

Supervisory cable

•

End user documentation

For specific applications, see Appendix A,
and adapters. For further assistance, contact Verilink Technical Support (800­285-2755 or 256-327-2255).

Specifications

, for additional cables

Installation 2-1

2-2 WANsuite 5650

C

HAPTE

R

3

Introduction

This chapter describes the menus and options associated with the WANsuite
5650’s VT100 interface. The screens displayed throughout this chapter were
accessed through the Supervisory port.

Accessing the VT100 Interface

You can access the VT100 inte rface locally via the Supervisory port. To
access the VT 100 screens, verify that the Supervisory type is “tty” a nd that
the Supervisory port speed is set to 38400 bps (the unit’s default port speed).

Screen Components

The VT100 terminal screens have several components common to all screens
(see Figure 3.1 below). These components include the device type (Verilink
WANsuite 5650), which is centered on the screen, the software and hardware
revision nu mbe rs (up per left ), th e ti me ( uppe r rig ht), the menu tit le ( “Main ” in
the figure below), and the serial number under which the unit is operating.

C

3

VT100 I

HAPTER

NTERFACE

Figure 3.1

NOTICE:

VT100 Terminal Screen Components

Because the WANsuite 5650 does not employ an internal time chip, the
unit cannot display the actual time of day. Rather, the “Time”
displayed on-screen represents the amount of time that the unit has been
operating since its last power cycle or reset. The unit marks time
beginning at 00:00 with each power cycle.

VT100 Interface 3-1

Cursor Controls

The VT100 interface uses a blinking cursor to select various menus and then

to select sub-menus and/or fields w ithin those menus. You can navigate using

this cursor in different ways, depending on the program you use. Most

programs allow use of the “Tab” key; others allow use of the arrow keys.

For keyboards that don’t have these standard keys or have only some of them,

an alternative set of cursor control commands is provided. Perform each

command by pressing a letter key while holding down the “Ctrl” key. You

may use the alternative commands (listed in the table below) and keyboard

commands interchangeably at your discretion.

You can navigate further within a menu as descri bed below.

Each menu screen is composed of fields. The two basi c field types are user-

selectable (most of these are in brackets or parentheses) and display-only (no

brackets or parentheses). If you can move the highlighted cursor to a field,

that field is user-selectable; all other fields are display-only. User-selectable

fields are those in which you can make changes or execute commands. To

save changed parameters, in most cases you will “Esc” out of the current

menu after cha nging th e paramet ers. In som e cases, you will pres s the “Ent er”

key to save new parameters.

Fields enclosed in brackets [ ] offer a list of selections from which to choose.

The selections may be made by pressing your Spacebar to “toggle” between

choices. Each time the Spacebar is pressed, a new item appears. When the

item you wish to choose is displayed, press the “Esc” key to save it.

Fields enclosed in parentheses ( ) are manipulated by one of two methods.

The first method is to press the “Enter” key to simply execute the defined

function. The second m ethod requires typing input. The most common type

of field in parentheses accepts typed input in the form of letters and/or

numbers. Typing characters when the field is highlighted causes the current

Keyboard Command

Alternate Command

Left Arrow

Ctrl+S

Right Arrow

Ctrl+D

Up Arrow

Ctrl+E

Down Arrow

Ctrl+X

Backspace

Ctrl+H

Delete

Ctrl+Z

NOTICE:

If you are not able to use your arrow keys, you may need to change the
settings within your terminal emulation program.

Field Types

3-2 WANsuite 5650

entry to be replaced by the new characters. To edit an existing entry rather

than replace it, press the right arrow key to move the cursor to the point that

needs editing. You may insert characters or delete them. Typed data must

always be inserted rather than typed over. If the field is full, you must first

delete at least one character before you can add another.

Table (column) headings enclosed with braces < > indicate that any entry in

that column is selectable. (See Figure 3.7

on page 3-10 for an example.)

NOTICE:

The Main Menu screen (shown in Figure 3.2) lists the functional user-

accessible menus. To activate a specific menu, tab to it (or use your arrow

keys) and press “Enter.” To exit this or any subsequent menu, press the “Esc”

key. If you exit the Main menu, th e terminal interf ace program ter minates.

This is a valid way to end a session. When you exit any menu other than the

Main menu, you will be returned to the previous screen.

The VT100 screens are automatically refreshed every 5 seconds.
However, you may also press Ctrl+U to refresh data on any screen.

Main Menu and Menu Structure

Figure 3.2

VT100 Main Menu Screen

CAUTION:

If you do not enter a keystroke for 10 minutes, the terminal interface
logs off automatically.

VT100 Interface 3-3

System Screen

The first option on the Main menu screen is the System screen (Figure 3.3).

This screen lets you view and set specific information about the unit in

service.

The System screen displays the fields shown in the table below.

The System screen displays the user-selectable prom pts listed in the table

below and described in detail in the paragraphs that follow.

Field

Description

Contact

Read/write field used to store the name of a point-of-contact for

system failu re.

Name

Read/write field that holds the unit’s name.

Location

Read/write field that holds the unit's location.

New Password

Read/write field used to change the unit’ s passw ord. Acceptable

characters for use in a password are digits 0–9 and letters A–Z

and a–z, for a total of 62 distinct characters.

Prompt

Function

Download App Code

Initiates the downloading of new application code.

Save and Restart

Saves the current configuration and restarts.

Maintenance Reset --

TDM

Resets unit to its default TDM configuration.

Figure 3.3

System Screen

3-4 WANsuite 5650

Download App Code

Use the “Download App Code” field to upgrade the software in your

WANsuite 5650 unit. The revision level for the software your unit is currently

using is displayed in the top line of the VT100 screens. After installing a

software upgrade, the new revision level will be displayed on this line.

To reprogram your WANsuite 5650 unit with new software:

Select the “

” field and press the “Enter” key. A

confirmation screen similar to the one shown in Figure 3.4 will display.

Select “

” to continue with the procedure. The screen will clear and the

message “

” will appear at the bottom.

After a short amoun t of time, the scree n will di splay the messages “

”

and “

.” At this point the software upgrade file must be

transferred to the unit.

A series of “

’s” will be displayed at the bottom of the screen while the

system waits for the file to begin downloading. Once it has begun, the

entire download process may take several minutes.

Set your teminal emulation program’s Protocol selection to “1K Xmodem.”

Use your terminal emulation program to select the a ppropriate

file for

uprading the software and begin sending the file. (If using HyperTerminal,

choose “Transfer/Send File...”.)

At the completion of the download, your system’s screen should display:

The unit will now update the application program flash, during which the

BERT LED will flash on and off. Once the flash has been updated, the unit

will reboot. After the unit reboots you should see the new software revision

level displayed in the top line of the VT100 screens.

Select this prompt to perform a Maintenance Reset to the unit’s default TDM

configuration. Any existing configurat ions will be lost and the unit will be set

back to its factory defaults. Selecting the Maintenance Reset prompt will

display a confirmation screen (Figure 3.4) where you will choose either to

proceed with the maintenance reset or abandon the procedure.

CAUTION:

1

2

Do not allow power to be removed from the unit while its memory is
being reprogrammed.

Download App Code

Yes

FILLING MEMORY WITH FFF

3

START UPLOAD

4

C

5
6

7

 

FILLED

Maintenance Reset--TDM

VT100 Interface 3-5

Figure 3.4

Selecting “Save and Restart” will display a confirmation menu similar to that

shown in Figure 3.4. Select “YES” to save the current configuration settings

and then restart the unit, or select “NO” to abandon the procedure.

Confirmation Screen

Save and Restart

NOTICE:

Performing a “Maintenance Reset” or a “Save and Restart” will
terminate communications with the unit. Refresh (by pressing
“Ctrl+U”) after approximately 10 seconds to restore communications .

3-6 WANsuite 5650

Interfaces Screen

The Interfaces screen displays a list of all the unit’s available interfaces as

shown in Figure 3.5.

From the Interfaces screen, you may choose from the following: SHDSL,

G.703, Serial, or Supervisory. Selecting an interface will display an initial

configuration screen for that interface. Each of these interfaces is described

below.

The SHDSL screen (Figure 3.6) lets you view and make changes to the

SHDSL interface's configuration as described below. In addition, this screen

displays the activity status and alarm values for the SHDSL interface.

Figure 3.5

Interfaces Screen

SHDSL Screen

VT100 Interface 3-7

Figure 3.6

Unit Type

Selects the unit type. T U-R repre sents a CP E termina l unit; TU- C represen ts a

CO terminal unit. The TU-C mode is for back-to-back operation needed for

E1 replac ement ap plication s.

Values:

TU-R, TU-C

Default:

TU-R

Timing (T x/Rx)

Sets the transmit and receive timing source to synchronize the unit’s internal

timing gener ators. In all cas es, slips are co ntrolled to oc cur on frame

boundaries at the network port when timing synchronization is lost. Choices

are as follows:

Internal –

The unit’s internal frequency standard is used for all timing.

SHDSL –

Timing is derived from the network recovered clock. Most

applications use this selection. (Default)

Serial –

The Transmit clock is sourced from the Nx64k and the Receive clock

is the SHDSL port recovered clock.

G.703 –

The Transmit clock is sourced from G.703 and the Receive clock is

the SHDSL por t recovered clock.

Valid Timing options depend on the selected unit type:

For STU-C:

Values:

Internal/Internal, G.703/G.703, Serial/Serial

Default:

Internal/Inter nal

For STU-R:

Values:

SHDSL/SHDSL

Default:

SHDSL/SHDSL

SHDSL Screen

3-8 WANsuite 5650

Expected R epeaters

This field is used to provision the number of repeaters in the selected span.

Values:

0, 1, 2, 3, 4, 5, 6, 7, 8

Default:

0 (zero)

Span Configuration

This value in this field represents a span configuration profile in the Span

Configurat ion Profile Table, which a pplies to this sp an. By defaul t, this

object will have the value “DEFVAL” (the index of the default profile).

Values:

User Span Profile 1, User Span Profile 2, DEFVAL (Default

Value)

Default:

DEFVAL

Span Alarm

Configuration

This value in this field represents an Alarm configuration profile in the

Endpoint Alarm Configuration Profile Table. The alarm threshold

configuration in the referenced profile will be used by default for all segment

endpoints in this span. Individual endpoints may override this profile by

explicitly specifying some other profile in the table. By default, this object

will have the value 'DEFVAL' (the index of the default profile).

Values:

User Alarm Profile 1, User Alarm Profile 2, User Alarm

Profile 3, DEFVAL (Default Value)

Default:

DEFVAL

The following paragraphs describe the display-only fields of the SHDSL

configuration screen.

Status

Provides overall st atus information of the span.

Detail Status

Displays current activity status of the network.

EOC In

Displays the EOC (Embedded Operations Channel) In.

EOC Out

Displays the EOC (Embedded Operations Channel) Out.

Discovered Repeaters

Displays the number of discovered repeaters on this span.

Line Rate

Displays the actual negoti ated line rate .

Maximum Line Rate

Displays the maximum physical line rate.

Transmission Mode

Displays the actual transmission mode (Annex-A or Annex-B).

In addition to the user-configurable and display-only fields, the SHDSL

screen has four function fields that lead to additional configuration screens.

These fields are Channels, Configuration Profiles, Alarm Profiles, and Span

Endpoints. To access these screens, simply move the cursor to one of these

fields and press the “Enter” key.

Selecting the “Channels” option from the SHDSL screen will display a TDM

Service Details screen. This screen is described in detail on page 3-30.

VT100 Interface 3-9

Configuration Profiles Screen

Selecting the Configuration Profiles function field from the SHDSL screen

will displa y the followin g screen:

This screen is used to view the available SHDSL span configuration profiles

(by profile name) and their established parameters. Each of the three

available configuration profiles

represents a span configuration profile in the

Span Configuration Profile Table, which applies to this span

.

Displayed parameters for each span configuration profile include the

following:

Configuration N am e

Displays the name of the defined span configuration profile.

Rate (Min)

Displays the minimum attai nable line rate in the span.

Rate (Max)

Displays the maximum attain able line rate in the span.

Remote

Shows whether the option to span remote is enabled or disabled.

Power Feeding

Shows whether support for optional power feeding in a SHDSL line is

enabled or disabled.

The user may view and change the details for a configuration profile by

moving the cursor to the desired profile name and pressing the “Enter” key.

(A Configuration Details screen like the one in Figure 3.8 will be displayed.)

The Configuration Details screen (

Figure 3.8

) is accessed by selecting a

profile name from the Configuration Profiles screen and pressing the “Enter”

key.

Figure 3.7

Configuration Profiles Screen

Configuration Details Screen

3-10 WANsuite 5650

Figure 3.8

This screen allows the user to view and change various parameters of the

selected Configuration Profile, which include the following:

Wire Mode

Displays the type of wire interface used by the span (always Two-Wire).

PSD Type

Used to confi gure the use of s ymmetric/a symmetric P SD (Power Spe ctral

Density) ma sk for the assoc iated line.

Values:

Symmetric, Asymmetr ic

Default:

Symmetric

Data Rate (M in)

This field is us ed to set the min imum attainab le line rate in the span.

D ata R a te (Max )

This field is us ed to set the maxi mum attainab le line rate in th e span.

Remote

This field enables/disables support for remote management of the units in a

SHDSL line from the STU-R vi a the EOC.

Values:

Enabled, Disabled

Default:

Enabled

Power Feeding

This field ena bles/disab les support fo r optional pow er feeding in a SHDSL

line; however, this version of the WANsuite 5650 supports only wetting

current. Other values will have no effect.

Values:

No Power, Power Feeding, Wetting Current

Default:

No Power

Transmission Mode

Used to set the regional setting of the span.

Values:

Annex-A

, Annex-B

Default:

Annex-B

Configuration Details Screen

(ITU-T G.991.2)

(ITU-T G.991.2)

VT100 Interface 3-11

Alarm Profiles Screen

Selecting the “Alarm Prof iles” option on the SHDSL scr een will displa y the

following screen:

The Alarm Profiles screen displays the current status of endpoint alarms.

Information is displayed for the following alarm parameters:

Alarm Profile N am e

This field displays the unique index associated with this Endpoint Alarm

profile. The values are obtained from the alarm configuration profile

referenced by this objec t.

Loop A tten

This field indicates the loop attenuation threshold

SNR M argin

This field indicates the SNR margin threshold.

ES

This field indicates the errored seconds threshold.

SES

This field indicates the severely errored seconds threshold.

CRC

This field indicates the CRC anomalies threshold.

LOSWS

This field indicates the LOSW second threshold.

UAS

This field indicates the unavailable seconds threshold.

The parameters for each Alarm Profile can be changed by moving the cursor

to the desired Profile name and pressing the “Enter” key; this will display an

Alarm Profil e Details scre en (Figure 3.10 ) for the selecte d profile. The

available configuration parameters are described below.

Figure 3.9

Alarm Profiles Screen

3-12 WANsuite 5650

Alarm Profile Details Screen

The Alarm Profile Details screen (Figure 3.10) is accessed by moving the

cursor over a profile name in the Configuration Profiles screen and pressing

the “Enter” key. This screen is used to configure the alarm threshold values

to be used for the selected segment endpoint.

P ro file N a me

This field displays the unique index associated with this Alarm profile.

Loop Attenuation

This field configures the loop attenuation alarm threshold. When the current

value exceeds this threshold, a crossing trap will be generated.

SNR M argin

This field configures the SNR margin alarm threshold. When the current

value drops below this threshold, a crossing trap will be generated.

ES

This field configures the threshold for the number of errored seconds (ES)

within any given 15-minute performance data collection interval. If the value

of errored seconds in a particular 15-minute collection interval reaches/

exceeds this value, a tr ap will b e generat ed. One tr ap will be sent per interval

per endpoint.

SES

This field configu res the th reshol d for the number o f seve rely err ored sec onds

(SES) within any given 15-minute performance data collection interval. If the

value of severely errored seconds in a particular 15-minute collection interval

reaches/exceeds this value, a trap will be generated. One trap will be sent per

interval per endpoint.

CRC

This field configur es the threshold for the number of CRC anomalies within

any given 15-minute performance data collection interval. If the value of

CRC anomalies in a particular 15-minute collection interval reaches/exceeds

this value, a tr ap will be genera ted. One trap wi ll be sent per inte rval per

endpoint.

Figure 3.10

Alarm Profile Details Screen

VT100 Interface 3-13

LOSWS

This field configur es the threshold for the number of Loss of Sync Word

(LOSW) Seconds within any given 15-minute performance data collection

interval. If the value of LO SW in a partic ular 15-mi nute collec tion interva l

reaches/exceeds this value, a trap will be generated. One trap will be sent per

interval per endpoint.

UAS

This field configur es the threshold for the number of unavailable seconds

(UAS) within any given 15-minute performance data collection interval. If

the value of UAS in a particular 15-minute collection interval reaches/exceeds

this value, a tr ap will be genera ted. One trap wi ll be sent per inte rval per

endpoint.

Span Endpoints Scree n

Selecting the “Span Endpoints” field on the SHDSL screen will display the

screen seen in Figure 3.11. The Span Endpoints screen displays each unit of

the span. User-selectable prompts are provided to view the Span Endpoint

Details (page 3-14), Span Endpoint Maintenance (page 3-16), Alarm Profiles

(page 3-12), and Span Endpoint Performance (page 3-17) screens. If the

SHDSL link is not up, only the local side of the span will be displayed.

Moving the cursor to an entry in the Unit column of this screen and pressing

the “Enter” key will display the span endpoint details for that unit. (See

on page 3-14.)

The Span Endpoint Detail s screen (Figure 3.12) is accessed by moving the

cursor to a Unit identifier in the Span Endpoints screen and pressing the

“Enter” key. This screen supports retrieval of unit inventory information

available v ia the EOC from units in a SHDS L line.

Endpoint Details Screen

Span

Figure 3.11

Span Endpoints Screen

Span Endpoint Details Screen

3-14 WANsuite 5650

Figure 3.12

This screen provides details on the following span endpoint parameters:

Ve n dor ID

Displays the Vendor ID.

Model Number

Displays the Vendor model number.

Serial Num ber

Displays the Vendor serial number.

EOC Software Version

Displays the Vendor EOC version.

Standard Version

Displays the version of the SHDSL standard implemented.

List Num ber

Displays the Vendor list number.

Issue N u m b er

Displays the Vendor issue number.

Software Version

Displays the Vendor software version.

Equipment Code

Displays the equipment code conforming to ANSI T1.213, Coded

Identifica tion of Equipm ent Entities.

Transmission Mode

C a p a b ility

Displays the transmissi on mode capabi lity of the SH DSL unit.

Endpoint Side

The endpoint side will always be “Network” when unit type is TU-R.

Wire Pair

Wire pair will always be “Wire Pair 1.”

Vendor Other

Displays other vendor information. For a WANsuite 5650 unit, this field

displays hardware revision (2 digits), manufacturing date (6 digits) and

software checksum (4 digits).

In addition to the displayed endpoint details, this screen also provides function

fields that are used to access the Span Endpoint Maintenance screen (Figure

Span Endpoint Details Screen

VT100 Interface 3-15

3.13), Span Endpoint Performance Screen(s) (Figure 3.14), and the Alarm

Profiles screen (Figure 3.9).

Span Endpoint Maintenance Screen

The Span Endpoint Maint enance sc reen (Fi gure 3.13 ) is ac cessed by mov ing the

cursor to the “Maintenance” field in the Span Endpoint Details screen and

pressing the “Enter” key. This screen supports maintenance operations (e .g.,

loopbacks) to be performed on segment endpoints.

The Span Endpoint Maintenance parameters are described as follows:

Loopback Type

This field controls configuration of loopbacks for the associated segment

endpoint.

Values:

No Loopback, Normal Loopback, Special Loopback

Default:

No Loopback

Loopback Tim eout

This field configures the timeout value in minutes for loopbacks initiated at

segments endpoints contained in the associated unit. A value of 0 (zero)

disables the timeout.

Tip Ring

This field indicates the state of the tip/ring pair at the associated segment

endpoint.

Pow er B ack off

This field configures the receiver at the associated segment endpoint to

operate in default or enhanced power backoff mode.

Values:

Default, Enhanced

Default:

Default

Figure 3.13

Span Endpoint Maintenance Screen

NOTICE:

3-16 WANsuite 5650

Only the Normal Loopback option has been implemented for the
WANsuite 5650.

Power Source

This field indicates the DC power source being used by the associated unit.

Restart Endp oint

This field enables the manager to trigger a soft restart of the SHDSL line at

the associated segment endpoint. The manager may only set this object to the

“restart” value to i nitiate a restart. The agen t will pe rform a restart af ter

approximately 5 seconds, and restore the object to the “ready” state.

Values:

Ready, Restart

Default:

Ready

Span Endpoint Performance Screen

The Span Endpoint Performance screen (Figure 3.14) is accessed by moving

the cursor to the “Performance” field in the Span Endpoint Details screen and

pressing the “Enter” key. This screen displays information on the

performance and error status of the span endpoints. This information is

provided in a summary form for complete totals as well as that for current 15-

minute and 1-day intervals.

Tim e Elapsed

Total elapsed time (in seconds) in the current 15-minute and 1-day intervals.

ES

Count of Errored Seconds (ES) on this endpoint since the unit was last

restarted.

CRC

Count of CRC anomalies on this endpoint since the unit was last restarted.

LOSWS

Count of Loss of Sync Word (LOSW) Seconds on this endpoint since the unit

was last rest arted.

SES

Count of Severely Errored Seconds (SES) on this endpoint since the unit was

last restarte d.

UAS

Count of Unavailable Seconds (UAS) on this endpoint since the unit was last

restarted.

Figure 3.14

Span Endpoint Performance Screen

VT100 Interface 3-17

Also included on the Span Endpoint Performance screen are options to view

the span endpoint performance summaries for 15-minute inte rvals and for 1-

day intervals. These screens display only a summary of the errors (ES, SES,

CRC, LOSWS, UAS) that have occurred on the span during the interval

selected.

The 1-Day Intervals screen also includes the status of monitored seconds

(MoniSec), which is defined as the amount of time in a one-day interval over

which the monitoring information is actually counted. This value will be the

same as the int erval durati on except in si tuations whe re, for any reas on,

performance monitoring data could not be collected.

The 15-Minute Intervals table provides one row for each endpoint

performance data collection 15-minute interval. The 1-Day Intervals screen

provides one row for each endpoint performance data collection 24-hour

interval.

G.703 Screen

The G.703 Configuration screen (Figure 3.15)

lets you view and make

changes to the G.703 interface's configuration as described below. In addition,

this screen provides a table that displays the error status values for the G.703

interface.

Line Coding

Sets the G.703 port line coding.

Values:

HDB3, AMI

Default:

HDB3

15-Minute and 1-Day Intervals Screens

Figure 3.15

G.703 Screen

3-18 WANsuite 5650

CRC4 Mode

Used to disable or enable CRC-4 detection/generation towards the SHDSL

network. When less than 32 timeslots are configured on the G.703 port, CRC-

4 detection/generation is based on filling the unused timeslots with a fixed

pattern configurable via the management interface. This CRC-4 detection/

generation is also require d for multirat e (single or sim ultaneous serv ices)

where less than 31 G.704 timeslots are carried over the SHDSL line.

Values:

Disable, Enable

Default:

Disable

Frame Type

Sets the type of framing used by the G.703 port.

Values:

Framed, Unframed

Default:

Framed

E Bit Generation

In framed mode,this is used to configure the CRC-4 detection/generation via

the manage ment inte rface.

Values:

Disable, Enable

Default:

Disable

RAI Generation

The RAI (Rem ote Alarm In dication) det ection shal l be in accordan ce with

ITU-T I.431 sec 3.4.1.2 and ITU-T G.704 Table 5A.

Values:

Disable, Enable

Default:

Enable

Sa4, Sa5, Sa6, Sa7, Sa8

Displays the status of special spare bits found in Timeslot 0.

Error Status and Alarm Thresholds Table

The unit can be programmed to generate an alarm condition based on a

specific level of performance degradation. The G.703 screen presents a table

that provides current error status and alarm threshold information.

Acceptable alarm thresholds are set for periods of 15 minutes (900 seconds).

The error types listed in the following paragraphs can be preset to a value

between 0 and 900 seconds. Setting a threshold field to “0” (zero) disables the

alarm on that statis tic. To effectively disa ble al arm rep ortin g, set all thres holds

to “0” (zero).

The 15-minute time fram e is a time window based on the accumulated counts

over the previous 15 one-minute intervals. In all cases, if the number of actual

network errored seconds in the previous 15 minutes reaches the preset

threshold for the specified error type, an alarm condition is declar ed.

The four columns of the status table are as follows:

•

Status

: Displays the current status of the network port.

Alarm

: Displays the alarm value of the network port. The unit declares an

alarm as soon as the count exceeds the threshold set.

Count

: Displays the number of events or occurrences of this statistic that

have been detected.

Threshold

: Displays a read/write field that can be set to a desirable

threshold.

•

•

•

VT100 Interface 3-19

3-20 WANsuite 5650

The table prov ides error st atus and alarm threshold in formation fo r the

following e rror para meters:

ES

Sets the Errored Seconds (ES) threshold. An ES is a 1-second period in which

at least one logic error occurred. The default threshold is 45 seconds.

SES

Sets the Severely Errored Seconds (SES) threshold. An SES is a 1-second

period in which at least 320 CRC errors or one Out- of-Frame (OOF) error

occurred. The default threshold is 5 seconds.

LOSS

Sets the Loss of Signal Seconds (LOSS) threshold. A LOSS is 1-second

period in which the E1 received signal is interrupted. The default threshold is

5 seconds.

UAS

Sets the Unavailable Seconds (UAS) threshold. A UAS is a 1-second period

in which consecutive severely errored seconds cause an unavailable state. The

threshold is 0 (zero) seconds (Disabled).

CSS

Sets the Controlled Slip Seconds (CSS) threshold. The default threshold is 0

(zero) seconds (Disabled).

BPVS

Sets the Bipolar Violation Errored Seconds (BPVS) threshold. A BPVS is a 1-

second period in which at least one bipolar violation occurred. The default

threshold is 0 (zero) seconds (Disabled).

OOFS

Sets the Out of Frame Seconds (OOFS) threshold. An OOFS is a 1-second

period in which a frame sync loss occurred. The default threshold is 5

seconds.

AISS

Sets the Alarm Indication Signal Seconds (AISS) threshold. An AIS is a 1-

second period when unframed all ones are received. The default threshold is 0

(zero) seconds (Disabled).

RAS

Sets the Remote Alarm Seconds (RAS) threshold. An RAS is generated by

the terminal equipment when an improper signal is received from the facility

(or upon receipt of unframed all ones). The default threshold is 0 (zero)

seconds (Disabled).

Reset Tim er

The status table also provides an option for setting the Reset Timer threshold.

This field is the contiguous number of seconds that an alarm parameter must

be clear before the alarm is reset. Applicable values range from 000 through

900. A value of “000” means the alarm will never be reset. The default value

is 30 seconds.

The G.703 configuration screen provides the user-selectable prompts

described i n the ta ble below.

Performance

The Performance prompt near the bottom of the G.703 configuration screen

displays a 24-hour performance summary screen (Figure 3.16), which

provides a summary of the error events that have occurred on the G.703

interface during each interval of the past 24 hours.

CAUTION:

To view a screen showing performance details for only a given 15-minute

period in the current 24-hour statistics, use the cursor to highlight the desired

period (Summary, Current, or Interval

) and press the “Enter” key. A screen

like the one below (Figure 3.17) will be displayed.

Prompt

Function

Clear Alarms

Resets the alarm conditions and counts to zero.

Performance

Displays a current count of the number of error events that have

occurred over the past 24 hours.

Channels

Displays the TDM Service Details screen (Figure 3.24

on

page 3-30), show in g e ach chan ne l by in dex num be r . Ea ch

channel’s service (by number) is displayed and can be changed

through user input.

Performance data will be lost upon power cycle or after performing a
Maintenance Reset/Restart.

Figure 3.16

G.703 Performance 24-Hour Screen

x

VT100 Interface 3-21

Figure 3.17

Select the “Performance 30 Day” prompt from the G.703 Performance 24

Hour screen to see a detailed summary of the error events that have occurred

during each interval of the past 30 days (shown below in Figure 3.18).

To view a screen showing performance details for only a given 24-hour period

in the current 30-day statistics, use the cursor to highligh the desired period

(Summary, Current, or Interval

) and press the “Enter” key. A screen like

the one below (Figure 3.19) will be displayed.

G.703 Performance 24-Hour Details Screen

Figure 3.18

G.703 Performance 30 Day Screen

x

3-22 WANsuite 5650

Serial Screen

The Serial screens let you view and make changes to the unit’s Serial

interface configurations as described in the paragraphs below. To make

changes to any Serial parameter, simply set the parameter to the desired

selection and press the “Esc” key.

Figure 3.19

G.703 Performance 30 Day Details Screen

Figure 3.20

Serial Scr een

VT100 Interface 3-23

Typ e

This parameter selects the type of interface (based on its electrical signal

characteristics) used by the equipment connected to the Serial port.

Values:

V.35, V.36, X.21

Default:

V.35

NOTICE:

Mode

By default, the Serial port serves as a DCE port in non-Packet modes.

If the Serial port connects to a DTE device (such as a FRAD or a router), the

Mode parameter must be set to “DCE.”

Values:

DCE

B u n d lin g

Selects whether the DTE channel assignment is made as a “Contiguous”

group or as “Alternate” channels. Selecting “Alternate” ensures ones density.

Because the unit allows individual channels to be configured for a service, a

value of “A rbitrary” will be r eturned fo r this p arameter if the cur rent chan nel

allocation is not contiguous or Alternate. The “Arbitrary” value can only be

supplied by the unit – it cannot be set by the user.

Values:

Contiguous, Alternate, Arbitrary

Default:

Contiguous

Start Channel

Selects the sta rting channe l in the 32-chan nel G.703 bi t stream. Starti ng with

the specifie d channe l, the un it automa tically as signs the channels that fol low.

Values:

1 through 32

Default:

1

# of Channels

Specifies t he number of ch annels to be as signed to the D TE.

Values:

0 through 31

Default:

31

Channel Rate

The unit can operate at any data rate that is a multiple of 64 kbps.

Values:

x64K

Inve rt C lock

In DTE Packet mode, this parameter changes the clock edge of the transited

data. The Invert Clock parameter is only available for use in DTE mode.

Values:

Disable, Enable

Default:

Disable

Tx Clock

Selects the clock the unit uses to sample the data transmitted from the DTE.

When set to “Internal,” the data is sampled directly with the transmit data

All multiple protocol cables (V.35, V.36 and X.21) are optional
equipment and must be ordered thro ugh Verilink or de signed to the
appropriate specifications. Refer to Appendix A, "Specifications‚" for
ordering information and cable specifications.

N

NOTICE:

3-24 WANsuite 5650

Start Channel, Number of Channels, and Channel Rate cannot be
changed if Bundling is not also changed from “Arbitrary.”

clock that is also supplied to the DTE as Transmit Clock. The “External”

option uses the external clock from the DTE.

Values:

Internal, E xternal

Default:

Internal

LL

The Local Loopback parameter can be set to “Permanent Off” or “DTE

Driven.” S electing “Perman ent Off” me ans no lo cal loop request s will be

accepted via this line. Selecting “DTE Driven” means the line can accept

local loop requests.

Values:

Permanent Off, DTE Driven

Default:

Permanent Off

V54

Selecting “Enable” allows the unit to respond to in-band V.54 loop codes. If

you select “Disable,” the unit ignores these codes.

Values:

Disable, Enable

Default:

Disable

CTS

The Clear To Send parameter can be set to “Permanent On,” “Permanent

Off,” or “DTE Dr iven.” If this parame ter is set to “Pe rmanent On,” th e CTS is

always “o n” no ma tter wha t the sta te of RTS. If set to “Perm anent O ff,” CTS

is always “o ff” no ma tter w hat t he state of RTS. If set t o “DT E Drive n,” C TS

follows RTS. In addition, when RTS and CTS are off, a pattern of all 1’s

(ones) is transmitte d.

Values:

Permanent On

, Permanent Off, DTE Driven

Default:

Permanent On

DSR

Data Set Ready can be set to “Permanent On,” or “Permanent Off.”

Values:

Permanent On

, Permanen t Off

Default:

Permanent On

DCD

The Data Ca rrier Det ect param eter can b e set to “Permane nt On,” “Perman ent

Off,” or “DTE Driven.”

Values:

Permanent On

, Permanent Off, DTE Driven

Default:

Permanent On

RTS

The Request To Send parameter determines the source from which the unit

reads the RTS signal stat us. If set to “DT E Driven,” the unit gets RTS from

the DTE on the Serial interface. If set to “Permanent On,” RTS is always

perceived as “on.”

Values:

DTE Driven, Permanent On

Default:

DTE Driven

RTS/CTS D elay

The Request To Send/Clear To Send parameter determines how long the unit

waits before it changes the level of CTS to match RTS when the CTS

parameter is set to “DTE Driven.”

Values:

0 (zero) ms, 1 (one) ms

Default:

0 ms

VT100 Interface 3-25

3-26 WANsuite 5650

DTR Alarm Control

Lets you set DTR Alarm Control parameters.

Values:

Permanent On, DTE Driven

Default:

Permanent On

DTR Alarm Status

Lets you view the curr ent DTR Alarm status.

Supervisor y Screen

The Supervisory Configuration screen (Figure 3.21) displays the current speed

of the Superv isory port inte rface. This sc reen is access ed by selecti ng

“Superviso ry” from the Interf aces scr een.

The Supervisory screen lets you view and change the Supervisory port speed

used by PPP and VT100. The Supervisory port only supports asynchronous

character for mats.

Speed

Changes the Supervisory port speed (in bits per second).

Values:

1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200

Default:

38400

Figure 3.21

Supervisory Config Screen

VT100 Interface 3-27

Service Table Screen

Selecting the “Services” option from the Main screen will display the Service

Table screen shown below (Figure 3.22). The Service Table screen provides a

view of the unit’s defined services and displays the Interface, Type, and Pair

parameters for each service.

The Service Table screen displays the available services listed by Index

number. From the Service Table screen, you can navigate:

to a Service Details screen (Figure 3.2 3) from the <Index> column;

to an Interface Details screen (Figure 3.24) from the <Interface> column

(when applicable);

or to a Type Details screen from the <Type> column (when applicable).

The prompts displayed on this screen are described in the following table:

Prompt

Function

Index

Opens the Service Details screen (Figure 3.23

on page 3-29).

Interface

Opens the Details screen for the Interface of the currently selected

service.

Type

Opens the Details screen for the Type of the currently selected service.

Figure 3.22

•

•

Service Table Screen

3-28 WANsuite 5650

•

Service Details Screen

This screen al lows the user to select and ch ange the serv ice paramete rs listed

below. The new parameters are saved when you press the “Esc” key and

return to the pr evious screen .

Interface

Selecting one of the available options provided in the “Interface” field will set

the interfac e parame ter for t he curren t service.

Typ e

Selecting one of the available options provided in the “Type” field will set the

type paramete r for the current service.

Pair

User-assigne d i nt eg er fie ld th at sp ec if ies w h er e to ro u te the tr af fi c fr om thi s

service. If the s er vi ce is ter min a ted by t he unit , set this va lue to “0 ” (zero ) .

Figure 3.23

Service Details Screen

VT100 Interface 3-29

TDM Service Details Screen

Selecting the Channels function field from the SHDSL screen will display the

TDM Service De tails screen (F igure 3.24).

This screen is used to view and set the TDM service parameters. Each

channel (0–31) is listed along with its configured Service number, Pair, and

Idle Pattern. (Use the PageUp or PageDown commands to view channels not

displayed.) The user can change the values for a channel’s Service or Idle

Pattern by navigating to the desired field and entering the appropriate value.

Service

This field is used to provisi on the service number of the selected cha nnel.

Values:

0, 3, 4, 7, 8

Idle Pattern

This field is used to provision the idle pattern of the selected channel. Values

are represented in hex format.

Values:

0 (zero) to FF

Figure 3.24

TDM Service Details Screen

3-30 WANsuite 5650

Applications

Accessed from the Main menu, The Applications screens describe diagnostics

and traps for Layer 3 and above that do not map to a specific service or

interface.

The Diagnostics screen (Figure 3.25) provides a table for viewing the current

settings for the test and maintenance functions performed on the available

interfaces . This screen sho ws an upper- level view of al l the interface s so you

can see if any port is under test. You may change Diagnostic parameters on

the Test Details screen (Figure 3.26), which is accessed by selecting the

appropriate interface under the <Description> column. The properties of the

Diagnostics table are described in the paragraphs below.

Descriptio n

Describes the type of interface selected for testing.

Loop Type

Describes the type of loop test (if any) performed on the selected interface.

The Test Details screen (Fi gure 3.26) is used to set the ty pe of test (if an y)

performed on the selected interface. Use the Spacebar to scroll through the

available c hoices.

Diagnostics Screen

Figure 3.25

Diagnostics Screen

NOTICE:

Diagrams explaining the diagnostic loops can be found in Appendix A.

Test Details Screen

VT100 Interface 3-31

Figure 3.26

Loop Type

Describes the type of loop test (if any) performed on the selected interface.

Values:

No Test (Loop Down), Dual Loop, Network Side Transparent,

Network Side Non-transparent, Customer Side Transparent,

Customer Side Non-transparent,

Default:

No Test (Loop Down)

The Trap Log screen (Figure 3.27) shows a collection of all the traps that

have been generated. A trap is a mechanism that permits a device to send an

alarm for certain network events to an SNMP management station.

Test Details Screen

Trap Log Screen

Figure 3.27

Trap Log Screen

3-32 WANsuite 5650

The table shown in this screen lists each trap by its Index number, and

displays th e type of error c aptur ed by th e trap ( Trap Number ) and the date an d

time that the trap was stored (Time Stamp).

VT100 Interface 3-33

3-34 WANsuite 5650

C

HAPTE

R

4

C

Introduction

This chapter describes the LED status indicators and control buttons
associated with the WANsuite 5650’s front panel interface.

Description of Front Panel

The front panel of the WANsuite 5650 is shown below. It features nine LED
status indicators and four user-activated control buttons.

HAPTER

4

F

RONT

ANEL INTERFACE

P

Figure 4.1

The following sections describe the functions of the LED indicators and the
control buttons.

Front Panel Buttons

The WANsuite 5650’s front panel control buttons are described in the
paragraphs below.

Po rt Select Button

The WANsuite 5650’s ports are defined as SHDSL, G.703, and (serial) Nx64k
port interfaces. The
from the available ports. When a particular port is selected using the

Verilink WANsuite 5650 Front Panel

PORT SELECT

button is used to cycle through and select

PORT

Front Panel Interface 4-1

SELECT

button, the port’s corresponding LED will flash. The status of the

and

LEDs will be the summary of the test states for the port

interfaces.

The

button cycles through the following port options on each

successive press:

No port selection

Nx64k (serial interface) port

G.703 port

SHDSL port

When the

Nx64k (serial interface)

port is selected, the LED labeled

flashes as an indication. The

and

buttons initiate/terminate tests, and the corresponding LEDs indicate the status

of tests on this port only.

When on the G.703 port selection, the

port LED flashes as an

indication. The

and

buttons in itiate/

terminate tests, and the corresponding LEDs indicate the status of tests on this

port only.

When on the SHDSL port selection, the

port LED flashes as an

indication. The

and

buttons initiate/

terminate tests, and the corresponding LEDs indicate the status of tests on this

port only. These tests are on the aggregate SHDSL payload.

If a port is sele cted, pressin g the

button will place or

remove a local loop on the selected port.

If a port is sele cted, pressin g the

button will place or remove

a remote loop on the selected port.

This button is not applicable.

LLOOP

PORT SELECT

•

•

•

•

RLOOP

LOCAL LOOP/ERR INJ

LOCAL LOOP/ERR INJ

LOCAL LOOP/ERR INJ

Nx64

REMOTE LOOP

G.703

REMOTE LOOP

SHDSL

REMOTE LOOP

NOTICE:

Port select will not operate if any locally initiated tests are in progress.

Local Loop/Error Injec t Button

Remote Loop Button

BERT Button

LOCAL LOOP/ERR INJ

REMOTE LOOP

4-2 WANsuite 5650

LED Indicators

The table below describe the WANsuite 5650’s front panel LED indicators.

LED Label

Off

Green

Amber

Red

No Power

Power applied to unit

Unit in test mode.

Mains Power Off

Trained with good

signal quality

Trained with marginal

signal quality

Training or attempting

to train with poor

signal quality and/or a

major network port

alarm is active

Service not configured

Service configured and

interface is operating

normally

Service is configured

and has minor alarms:

RAI; Slip

Service configured and

interface is not

operating normally:

LOS; LOA; AIS.

Service not configured

Service configured and

interface is operating

normally

Service configured and

interface is not

operating normally or

port mismatch

Nx64k service not

configured

RTS/C

control line is OFF

"RTS" or "C" control

line (from DTE) is ON

Nx64k service not

configured

RLSD/I

control line is OFF

"RLSD" or "I" control

line (from DTE) is ON

No loop present

A local loop is active

on the selected

customer port

A local loop is active on

the selected customer

port

A local loop is active

on the SHDSL port

No loop present

A remote loop is active

on the selected

customer port

A remote loop is active

on the selected

customer port

A remote loop is active

on the SHDSL port

not applicable

not applicable

not applicable

not applicable

Table 4.1

POWER

SHDSL

G.703

Nx64

RTS/C

LED Indicators

NOTICE:

or

SHDSL, G.703

The
the port select button

, and

Nx64

port LEDs will flash when selected by

RLSD/I

LLoop

RLoop

BERT

or

Front Panel Interface 4-3

4-4 WANsuite 5650

A

PPENDIX

A

Data Interfaces

Line Rate:

200 kbps–2056 kbps

Line Framing:

Aligned 2.048 Mbps (G.991.2 E7)

Line Code:

Trellis Coded Pulse Ampl itude Modulation

Connection:

8-pin modular jack at 135 Ohms

Line Rate:

2.048 Mbps (±50 ppm)

Line Framing:

Framed or Unfra med

Line Code:

AMI or HDB3

Input Signal:

E1, +1 to -27 dB (ALBO)

Connection:

8-pin modular jack at 120 Ohms

Output Signal:

3.0 V ±10% base–peak into 120 Ohms with protection

Jitter Control:

per G.823 Sections 2.1 and 3.0

Ones Density:

HDB3, alternate fill; complies with G.701 and G.703

Connection:

DB-25 female

DTE Ports:

Selectable V.35, V.36, or X.21

Data Rate:

Synchronous,

x64 kbps (where

= 1–32)

Embedded messaging to enable management of the customer ports and services.

SHDSL Port

G.703 Port

A

PECIFICATIONS

A

S

PPENDIX

Serial Interface

N

Management Interfaces

EOC (Embedded Operations Channel)

N

A-1

Connection:

DB-9 female

Data Rates:

(bps) 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200

(default: 38400 bps)

Protocols:

VT100

Power

Voltage Input:

100–240 VAC

Frequency:

50 or 60 Hz

Dissipation:

10 W maximum (34.15 BTU/hour)

Current:

200 mA maximum

Mounting:

Stand-alone

Weight:

2.13 lb. (0.97 kg)

Dimensions:

Width 8.36 in. (21.234 cm)

Height: 1.65 in. (4.191 cm)

Depth: 9.11 in. (23.139 cm)

Operating Temp:

32° to 122°F (0° to 50°C)

Storage Temp:

-13° to 158°F (-25° to 70°C)

Humidity:

96% maximum (non-condensing)

Activation:

Programmable thresholds on all interfaces

Reporting:

Via SHDSL EOC or local management port

Compliance:

CISPR 22 Class B

Safety:

EN 60950 (1992)

Performance:

15-minute and 30-day monitoring (sampled every second)

Network Loops:

Line loopback or maintenance loopback (see Figures A-1

and A-2)

Mechanical

Environmental

Supervisory Port

Alarms

Industry Listings

Diagnostics

NOTICE:

All the following loopback diagrams show the loops as if the unit is
configured as an STU-R. If the unit were configured as an STU-C, the
Network and Customer sides would be reversed.

A-2 WANsuite 5650

Network

Port

(G.SHDSL)

Network

Port

(G.SHDSL)

Network

Port

(G.SHDSL)

Figure A.1

G.SHDSL Loopback Diagrams

WANsuite 5650

Network

Framer

X

Internal Logic

G.SHDSL Maintenance Normal Loop

WANsuite 5650

Network

Framer

Internal Logic

G.SHDSL Network Side Dual Loop

WANsuite 5650

Network

Framer

Internal Logic

G.SHDSL Network Side Transparent Loop

X

X

G.703

Framer

Port

Logic

G.703

Framer

Port

Logic

G.703

Framer

Port

Logic

G.703

Port

Nx64

Port

G.703

Port

Nx64

Port

G.703

Port

Nx64

Port

Network

Port

(G.SHDSL)

Network

Port

(G.SHDSL)

Network

Port

(G.SHDSL)

WANsuite 5650

Network

Framer

AIS

AIS

Internal Logic

X

X

G.703

Framer

Port

Logic

G.SHDSL Network Side Non-Transparent Loop

WANsuite 5650

Network

Framer

X

Internal Logic

G.703

Framer

Port

Logic

G.SHDSL Customer Side Transparent Loop

WANsuite 5650

Network

Framer

X

AIS

AIS

Internal Logic

G.703

Framer

Port

Logic

G.SHDSL Customer Side Non-Transparent Loop

G.703

Port

Nx64

Port

G.703

Port

Nx64

Port

G.703

Port

Nx64

Port

A-3

Network

Port

(G.SHDSL)

Network

Port

(G.SHDSL)

Network

Port

(G.SHDSL)

Figure A.2

G.703 Loopba ck Diagrams

WANsuite 5650

Network

Framer

Internal Logic

G.703 Network Side Dual Loop

WANsuite 5650

Network

Framer

X

Internal Logic

G.703 Network Side Transparent Loop

WANsuite 5650

Network

Framer

AIS

X

Internal Logic

G.703 Network Side Non-Transparent Loop

G.703

Framer

Port

Logic

G.703

Framer

Port

Logic

G.703

Framer

Port

Logic

G.703

Port

Nx64

Port

G.703

Port

Nx64

Port

G.703

Port

Nx64

Port

Network

Port

(G.SHDSL)

Network

Port

(G.SHDSL)

A-4 WANsuite 5650

WANsuite 5650

Network

Framer

X

Internal Logic

G.703

Framer

Port

Logic

G.703 Customer Side Transparent Loop

WANsuite 5650

Network

Framer

X

AIS

Internal Logic

G.703

Framer

Port

Logic

G.703 Customer Side Non-Transparent Loop

G.703

Port

Nx64

Port

G.703

Port

Nx64

Port

Network

Port

(G.SHDSL)

Network

Port

(G.SHDSL)

Network

Port

(G.SHDSL)

Figure A.3

Nx64 Loopback Diagrams

WANsuite 5650

Network

Framer

Internal Logic

Nx64 Network Side Dual Loop

WANsuite 5650

Network

Framer

Internal Logic

Nx64 Network Side Transparent Loop

WANsuite 5650

Network

Framer

Internal Logic

Nx64 Network Side Transparent Loop

X

AIS

X

G.703

Framer

Port

Logic

G.703

Framer

Port

Logic

G.703

Framer

Port

Logic

G.703

Port

Nx64

Port

G.703

Port

Nx64

Port

G.703

Port

Nx64

Port

Network

Port

(G.SHDSL)

Network

Port

(G.SHDSL)

WANsuite 5650

Network

Framer

X

Internal Logic

G.703

Framer

Port

Logic

Nx64 Customer Side Transparent Loop

WANsuite 5650

Network

Framer

X

AIS

Internal Logic

G.703

Framer

Port

Logic

Nx64 Customer Side Non-Transparent Loop

G.703

Port

Nx64

Port

G.703

Port

Nx64

Port

A-5

Ordering Information

Each WANsuite 5650 unit is supplied with the following standard equipment:

*Verilink Technical Support: toll-free 800-285-2755, or direct 256-327-2255

The following optional equipment is available for the WANsuite 5650:

Part Number

Description

(call for part number*)

WANsuite 5650 unit

33-00209

Power cable

9-1001-023-010

Network Cable

33-00221

Serial (SUPV) Cable (DB9 male DB9 female)

45-00155

Verilink End User “Quick Start” Documentation

Part Number

Description

9-1001-127-010

Serial (DCE) Cable (DB25–Cisco DB60), 10 ft

9-3100-002-1

Rack Mount, 19 in., for single stand-alo ne unit

9-3100-002-2

Rack Mount, 23 in., for single stand-alo ne unit

9-1001-120-006

Serial (DCE) Cable (DB25–DB25, M/M, pin/pin) (EIA530/RS232), 6 ft

9-1001-094-005

Serial (DCE) Ca ble (DB25–Winchester 34-pin (V.35) M/M, pin/pin), 5 ft

9-1001-094-010

Serial (DCE) Cable (DB25–Winchester 34-pin (V.35) M/M, pin/pin), 10 ft

9-1001-124-005

Serial (DCE) Cable (DB25–V.35, M/F, pin/pin), 5 ft

9-1001-111-002

X.21 Cable (DB25/DB1 5 X.21, M/M), 2 ft)

Optional Equipment

A-6 WANsuite 5650

Connector Pin Assignments

The table below displays Serial Interface Pin Assignments for the DCE Mode.

Function

Abbrev.

Direction

DB-25*

V.35

V.36

X.21

Frame Ground

FG

n/a1A201

Transmit Data

TD

Input2P42

Receive Data

RD

Output

3 R 64Request to Send

RTS

Input4 C 73

Clear to Send

CTS

Output

5D 9

Data Set Ready

DSR

Output

6E11

Signal Ground

SG

n/a7 B 198

Data Carrier Detect

DCD

Output

8F13

5

Secondary Receiver Clock

(S)RC

Output

9X2613Secondary Dat a C arr ier Detect

(S)DCD

Output

103112

Secondary External Transmitter Clock

(S)ETC

Input11W357

Secondary Transmitter Clock

(S)TC

Output

12AA23

Secondary Clear to Se nd

(S)CTS

Output

13

27

Secondary Transmit Data

(S)TD

Input

14 S 22

9

Transmitter Clock

TC

Output

15Y5

Secondary Receive Data

(S)RD

Output

16 T 24

11

Receiver Clock

RC

Output

17V8

6

Local Loopback

Loop 3

Input18L10Secondary Requ es t to Se nd

(S)RTS

Input

19 2510

Data Terminal Ready

DTR

Input20H12Remote Loopback

Loop 2

Input21N14Secondary Data Set Ready

(S)DSR

Output

2229Secondary Data Terminal Ready

(S)DTR

Input2330

External Transmitter Clock

ETC

Input24U1714

Test Indicator

Output

25 NN18

Function

Abbrev.

Direction

DB-25*

V.35

V.36

X.21

Serial Interface Pin Assignments (DCE Mode)

A-7

SHDSL Interface Pin Assignments

The

interface is a standard eight-pin modular jack. The table below

displays the pinout assignments.

The

physical interface is a standard eight-pin modular jack. The table

below displays the pinout assignments.

The

interface is a standard DB-9, nine-pin modular

jack. The table below displays the pinout assignments.

Pin

DSL NET Interface

1, 2, 3

Not used

4

ANALOG Input/Output

5ANALOG Input/Output

6, 7, 8

Not Used

Pin

E1 Equipment Interface

Pin

Signal

1

Data Out

1

Data In

2

Data Out

2

Data In

3

Internally strapable to

Chassis return

3

Internally strapable to

Chassis return

4

Data In

4

Data Out

5

Data In

5

Data Out

6

Internally strapable to

Chassis return

6

Internally strapable to

Chassis return

7, 8

Not Used

7,8

Not Used

Pin

DCE Mode

DTE Mode

1

DCD out

LL out

2

Rx Data out

Tx Data out

3

Tx Data in

Rx Data in

4

DTR in

DSR in

5

Signal Ground

Signal Ground

6

DSR out

DTR out

7

RTS in

CTS in

8

CTS out

RTS out

9

No connect

No connect

SHDSL

G.703 Connector Pin Assignments

G.703

A-8 WANsuite 5650

Supervisory Port Pin Assignments

SUPERVISORY PORT