TRANSPORT
®
1060A Broadcast Card
Configuration Guide
45-00118
1.00
321
4 5 6
B
N
®
TRANSPORT
STATUS
1060A
Broadcast
ACO
A
FORCED
ACO SW
Front Panel Description
1 Status: Green LED illuminates when the unit is powered and operation is normal. The red LED illuminates when an alarm exceeding
thresholds is detected or for other unit failure.
2 ACO: Amber LED illuminates when the ACO (alarm cutoff) switch is placed in the left (On) position. It indicates that the alarm relay
contacts are forced to the
3 ACO SW: The alarm cutoff switch controls the alarm relay circuitry. When the switch is placed in the left (On) position, this circuitry is
deactivated. The ACO indicator still functions as usual.
4 Forced: Amber LED illuminates indicating that the
5 A / B: Either the A or B green LED illuminates indicating which input is being broadcast to the ports. Even if both Port A and Port B have
input, Port A will be selected and the A indicator illuminates.
6 Force Switch: This switch is used to force the input to either the A or B input.
No Alarms
condition.
Force
switch is in either the A or B direction.
TRANSPORT
®
General
The TxPORT 1060A Broadcast card (part num ber F1060-100A-111) is used to expand a single T1 input to
14 T1 inputs w here bridging m ay not be po ssible or
practical.
The inputs are redundant , switching from the Port A
to Port B or Port B to Port A on receipt of an alarm indication signal (AIS) or on a loss of signal (LOS). AIS
occurs on the r eceipt o f 8192 consec utive ones. LO S
occurs on the receipt of 175 consecutive zeros.
Installation
The 1060A card is designed to be installed in a single
unit housing module for standalone desktop use or for
wall mounting.
Operation
The card has t wo input choices - A or B. The gr een
LEDs indicate w hich si de is sup ply in g the in put . The
unit alarms on a loss o f signal (LOS) or on an al arm
indication signal (AIS).
The manual force switch is used to select the input to
either side A or the side B. The
ber) indicates that the force switch is out of th e
mal) position. The unit will stay in the selected input
mode unless an alarm condition is detected on the selected input. The unit will not switch from the selected
input if an alarm condition exists on the other input.
The unit has a Bridge or Term option on both inputs al-
lowing more than one input to be tied together with
the last one terminated.
FORCED
LED (am-
N
(nor-
Specifications
Input (A/B): Impedance terminated 100 Ω (± 2%)
Unterminated 1000 Ω
Output: Per 62411 waveform into 100 Ω
Power
DC Power: - 48 VDC (± 10%), 50 mA max
2.5 Watts, 8.5 BTU maximum
Connection: Terminal block
Mechanical
Mounting: Desktop
Wall
Horizontal or vertical rack
Vertical nest mount
Dimensions: 1.72 in (4.37 cm) Wide
6.8 in (17.27 cm) High
10.5 in (26.67 cm) Deep
Weight: 4.0 lbs (1.81 kg)
Industry
FCC Compliance: Part 15 Subpart B, Cla s s A
FCC Part 68 Reg:
Standards
1
1060A Broadcast Card Rear Panel
81
81
EXPAND
AB
Expand:
1818
1 2 3 4 5
These two 8-pin modular jacks are used for jumping the A or B inputs together to provide additional inputs.
T1 IN
AB
UNTERM
26 50
A
251
Alarm / Power
TERM
B
Rear Panel Description
Alarm /
Power Pinout
Pin Function
148 VDCReturn
2 Alarm Common
48 VDC
180 mA
61
3 -48 VDC
4 Frame Ground
5 Normally Close d
6 Normally Open
2
T1 IN:
These two 8-pin modular jacks are used for the T1 input signal as well as the output of each input. These 2 connectors output AIS
with no input.
3
Terminate/Unterminate:
These two slide switches are used for setting the A or B input. They are recessed and can be moved with a
screwdriver. Terminate is used when the expansion connector is not used. Unterminate is used when the expansion connector is daisy
chained.
4
T1 Broadcast Port:
This 50-pin female connector is used for the expanded outputs of either the A or B inputs. Refer to the pinout table
below.
5
Alarm:
This 6-pin connector is used as follows for the alarm connection. Th e alarm connection is made on pins 2 and 5 to operate in a
normally closed mode (NC - opens on alarm) or on pins 2 and 6 to operate in a normally open mode (NO - closes on alarm). The contacts
are rated at 1.0 Amp AC or 1.0 Amp DC. 18- to 20-gauge wire is recommended.
5
Power:
This 6-pin connector i s used as follows for the power connection. The unit requires a -48 VDC power source that is capable of
supplying 50 mA current. Connect a chassis ground lead to pin 4. Connect the -48 VDC lead to pin 3. Connect the return lead to pin 1. 18to 20-gauge wire is recommended.
T1 Broadcast Port Pinout
Tip Ring Function
1 26 Output # 1
2 27 Output # 2
3 28 Output # 3
4 29 Output # 4
5 30 Output # 5
6 31 Output # 6
7 32 Output # 7
8 33 Output # 8
9 34 Output # 9
10 35 Output # 10
11 36 Output # 11
12 37 Output # 12
13 38 Output # 13
Tip Ring Function
14 39 Output # 14
15 40 Not Used
16 41 Not Used
17 42 Not Used
18 43 Not Used
19 44 Not Used
20 45 Not Used
21 46 Not Used
22 47 Not Used
23 48 Not Used
24 49 Not Used
25 50 Frame Gnd
Expand / T1 In Pinout
Pin EXPAND T1 IN
1 Data Out Data In
2 Data Out Data In
3 Not Used Not Used
4 Not Used Data Out
5 Not Used Data Out
6 Not Used Not Used
7 Chassis Gnd Chassis Gnd
8 Chassis Gnd Chassis Gnd
TRANSPORT
127 Jetplex Circle
Madison, Alabama 35758
Sales and Marketing
800-926-0085
205-772-3770
info@txport.com
Technical Support
800-285-2755
205-772-3770
support@txport.com
Returns/RMA
800-926-0085, ext. 2227
®
Loading...