Verifone NURIT8000SWM User Manual

NURIT 8000

Wireless Palmtop

Solution

Installation Manual

Copyright Notice

Copyright© Lipman Electronic Engineering Ltd. All
rights reserved.

The content of this publication is for informational
purposes only and is subject to change without
notice. It does not represent a commitment on the
part of Lipman Electronic Engineering Ltd.

No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval
system, or translated to any language in any form
by any means without the prior written permission
of Lipman.

Trademark Information

NURIT® is a registered trademark of Lipman
Electronic Engineering Ltd. All other product and
brand names contained in this manual are
trademarks of their respective owners.

Catalog Number

DOC00222 Orig.

Print Date

February 2004

Lipman Electronic Engineering Ltd.
11 Haamal Street, Park Afek, Rosh Haayin, Israel 48092
Tel: +(972)-3-9029730 Fax: +(972)-3-9029731
E-mail: [e-mail]

Web Site: www.lipman.biz

Foreword

Thank you for purchasing the NURIT 8000
Wireless Palmtop Solution. You now own one
of the most advanced electronic point-of-sale
(POS) terminals manufactured today.

This manual provides basic installation
instructions. To fully utilize the features of
your NURIT 8000, and for general safety
purposes, it is recommended that you
familiarize yourself with this manual, the
terminal and any peripheral equipment or
accessories.

Figure 1 NURIT 8000 - General View

Installation Manual iii

Note

All graphic images in this manual
are for illustrative purposes only.
Different models of this terminal
may exist and may vary in
appearance according to country
of use or particular customer
requirements.
The basic installation procedure is
the same for most units.
The operation of the terminal is
application-dependent.

It is recommended that you store this
manual in a safe place for future reference.

iv Installation Manual

Table of Contents

Copyright Notice ........................................ ii

Trademark Information................................. ii

Catalog Number ......................................... ii

Print Date ................................................ ii

Foreword............................................. iii

Product Regulatory Information ....................... 1

FCC Compliance Statement............................ 1

FCC Part 15 Requirements ............................. 1

FCC Part 68 Requirements ............................. 2

FCC Part 90 Requirements ............................. 4

In Canada: ................................................ 4

EU Directives Compliance Statement ................ 4

Document Conventions ................................. 5

General Safety Instructions.......................... 7

Radio Frequency Energy Emission ...................11

Safety Precautions for Medical Devices............. 12

Pacemakers .............................................12

Other Medical Devices.................................12

Safety Precautions for Other Electronic Devices .. 13

Specifications ....................................... 14

Initial Setup .........................................15

Unpacking the Box .....................................15

Contents Checklist .....................................16

Selecting a Point-Of-Sale Location ..................19

Optional Accessories ...............................21

General Features ................................... 25

Installation Manual v

Installing the Battery Pack........................ 28

Battery Pack Maintenance ............................30

Connecting the NURIT 8000 to the AC Power Supply32

Installing the External Modem.................... 34

Connecting the Car Adapter

Loading Paper in the Printer...................... 37

Installing the Keypad Privacy Shield............. 39

Installing a SIM or SAM Card

Installing the SIM/SAM Cardholder Compartment Cover .. 45

Installing a SIM Card in the TEL SIM Slot............47

Connecting Peripheral Devices.......................50

Connecting a Cellular Headset ................... 52

General Care and Maintenance .....................53

Cleaning the NURIT 8000..............................53

Cleaning the Printer ...................................54

Maintenance Recommendations .....................55

Technical Assistance...................................55

Shipping the NURIT 8000 .............................. 56

Troubleshooting.....................................57

Appendix A Using the Magnetic Card Reader ......64

Appendix B

Installation Notes...................................67

Using the Smart Card Reader

........................ 35

.........................41

.......... 65

vi Installation Manual

List of Figures

Figure 1 NURIT 8000 - General View iii
Figure 2 Secure Device Label 15
Figure 3 NURIT 8000 – Box Contents 18
Figure 4 NURIT 8000 - Optional Accessories 21
Figure 5 NURIT 8000 - Top View 27
Figure 6 NURIT 8000 - Bottom View 27
Figure 7 Battery Pack Installation 28
Figure 8 Battery Pack Removal 29
Figure 9 AC Power Supply Connection 32
Figure 10 External Modem Installation 34
Figure 11 Car Adapter Connection 35
Figure 12 Loading Paper in the Printer 38

Figure 13 Keypad Privacy Shield Installation 39
Figure 14 SIM/SAM Cardholder Locking-Clasp 43
Figure 15 SIM/SAM Card Installation 44
Figure 16 SIM/SAM Cardholder Compartment

Cover Installation 46

Figure 17 Void Label Installation 46
Figure 18 SIM Cardholder Ejection 47
Figure 19 SIM Card Installation 48
Figure 20 SIM Cardholder Insertion 48
Figure 21 Barcode Reader Connection 51

Figure 22 Cellular Headset Connection 52
Figure 23 Magnetic Card Reader 64
Figure 24 Smart Card Reader 65

Installation Manual vii

Product Regulatory
Information

Note

The following product regulatory
information and compliance
statements apply to all models of
the NURIT 8000x, where x
represents a suffix, such as S,
SVP, or Secure, designating the
specific security features of a
particular model.

Caution

Changes or modifications to this
device that are not expressly
approved by the party responsible
for compliance could void the
user's authority to operate the
equipment.

FCC Compliance Statement

Manufacturer: Lipman Electronic Engineering Ltd.

Model: NURIT 8000

FCC Part 15 Requirements

This equipment has been tested and found to
comply with the limits for Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment
is installed and operated in a commercial
environment.

Installation Manual 1

This equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation.

Operation of this equipment in a residential area is
likely to cause harmful interference in which case
the user will be required to correct the interference
at his/her own expense.

If this equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.

•

Increase the separation between the
equipment and the receiver.

•

Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.

• Consult your dealer or an experienced
technician for help.

Connection of peripherals to this unit requires the
use of grounded, shielded cables to ensure
compliance with the class B limits.

FCC Part 68 Requirements

[Applicable when using optional NURIT 8000
docking station or NURIT 8000 external modem]

The FCC has established rules permitting this
device to be directly connected to the telephone
network. Standardized FCC Part 68 compliant
telephone line cords and modular jacks are used
for these connections. This equipment should not
be used on party or coin lines.

2 Installation Manual

If this device is malfunctioning, it may be causing
harm to the telephone network; this device should
be disconnected until the source of the problem
can be determined and until repair has been made.
If this is not done, the telephone company may
temporarily disconnect service.

The telephone company may make changes in its
technical operations and procedures; if such
changes affect the compatibility or use of this
device, the telephone company is required to give
adequate notice of the changes. You will be advised
to file a complaint with the FCC.

If the telephone company requests information on
what equipment is connected to their lines, inform
them of:

• The telephone number to which this unit is
connected

• The AC Ringer Equivalence Number: 00B

• The USOC jack required: RJ-11C

• The FCC Registration number: (See the

underside of the unit and/or applicable unit
documentation for this number.)

The Ringer Equivalence Number (REN) is used to
determine how many devices can be connected to
your telephone line. In most areas, the sum of the
RENs of all devices on any one line should not
exceed five (5). If too many devices are attached,
they may not ring properly. To be certain of the
number of devices that may be connected to the
line, as determined by the total RENs, contact the
telephone company to determine the maximum
REN for the calling area.

Installation Manual 3

FCC Part 90 Requirements

This device may contain a radio transceiver
module, (FCC ID number is located on the bottom
of the terminal), operating under Part 90 of the
FCC rules in a licensed part of the radio spectrum.
Qualified personnel must perform service or repairs
to the radio portion of this device. Any
unauthorized modification to the radio module,
shielding, or antenna system may void the user’s
authority to operate this device.

This device has been tested and meets RF exposure
guidelines for hand held operation pursuant to
FCC OET Bulletin 65 Supplement C ed. 01-01,
IEEE 1528/D1.2 (2003) and Industry Canada RSS­102 (1999).

In Canada:

This digital apparatus does not exceed the class B
limits for radio noise emissions from digital
apparatuses set forth in the Radio Interference
Regulations of the Canadian Department of
Communications.

Cet appareil numérique n'émet pas de bruits
radioélectriques dépassant les limites applicables
aux appareils de la classe B, déterminée par la
Réglementation d’Interférence Radio du Ministère
canadien des Communications.

EU Directives Compliance Statement

This product complies with the requirements of
applicable EU Council Directives.

Caution

Any unauthorized modification of
the equipment may void the user’s
authority to operate this device.

4 Installation Manual

Document Conventions

Note - Helpful hints and other important

information that will help you get better use
from your NURIT.

Caution

if not observed, could result in damage to the
NURIT or other equipment.

Warning - Failure to follow specific

procedures and practices may result in
personal injury.

- Information about procedures that,

Installation Manual 5

General Safety Instructions

Warning

Failure to observe these
instructions may result in severe
personal injury or damage to the
NURIT 8000 or other equipment.

Note

These safety instructions are
based in general on those provided
by Underwriters Laboratories (UL)
Inc. U.S.A.

When using the NURIT 8000 or any
associated device, the following basic safety
precautions should always be observed to
reduce the risk of fire, electric shock, or
personal injury:

•

Read and make sure you understand all
instructions.

• Follow all warnings and instructions
marked on the device and in this manual.

• Disconnect the device from the power
supply and any peripherals before
cleaning.

• Do not use liquid or aerosol cleaners. Use a
damp cloth for cleaning and/or a soft
brush.

•

Do not use the device near water,
especially when using the AC/DC Power
Adapter or external modem.

• Never spill any liquid on the device.

Installation Manual 7

•

Place the device in a stable position on a
solid surface. When operated hand-held,
grasp the device securely. Serious damage
may result if the device falls.

• The optimal operational position for the
terminal is hand-held at an angle of

o

approximately 30

. The terminal is also
designed for optimal tabletop usage. Keep
the terminal a short distance from your
body.

• Do not cover slots and openings of the
device. They may be provided for
ventilation and protection against
overheating. Never place the device near
radiators, or in a place where proper
ventilation is not provided.

•

Use only the power source as marked on
the device. If you are not sure of the type of
the power supplied to your location,
consult your dealer or local power
company.

• Do not place objects on the power cord.
Install the device where no one can step on
the cord.

• Do not overload wall outlets and extension
cords as this can result in the risk of fire or
electric shock.

• Never push objects into the device through
slots (other than those specifically intended
for the stylus, magnetic stripe or smart
cards, or SAM/SIM cards), as this may
result in fire or electric shock.

8 Installation Manual

•

To reduce the risk of electric shock, do not
disassemble any of the equipment or
accessories referred to in this manual. If
required, take the equipment to a qualified
service representative. Opening or
removing covers may expose you to
dangerous voltages or other risks. Incorrect
reassembly can cause electric shock.

• Disconnect the device from the power
supply and any peripherals and refer to
qualified service personnel under the
following conditions:

• The power supply cable or plug is

damaged or frayed.

• Liquid has been spilled into the

device.

• The device has been exposed to rain

or water.

• The device does not work normally,

when following the operating
instructions.

• The device has been dropped or

damaged.

•

The device exhibits a distinct
change in performance.

• When using the NURIT 8000 optional
docking station and/or external modem
during thunderstorms, disconnect the
telephone line, if possible. There may be a
remote risk of electric shock from lightning.

• Never install telephone wiring during a
lightning storm.

Installation Manual 9

•

Never install telephone jacks in wet
locations unless the jack is specifically
designed for wet locations.

• Never touch non-insulated telephone wires
or equipment unless the telephone line has
been disconnected at the network interface.

• Use caution when installing or modifying
telephone lines.

• When in the vicinity of a gas leak, do not
use the NURIT 8000, a standalone
telephone or a telephone connected to a
POS terminal or docking station to report
the leak.

• Take care when installing an internal
battery pack. If installed incorrectly, it may
explode. Use only a Lipman supplied
battery pack. Discard used battery packs
according to local regulations.

10 Installation Manual

Radio Frequency Energy Emission

Your NURIT 8000 may contain a transmitter
and receiver that emit radio frequency (RF)
energy. The actual frequency range used by
the NURIT 8000 is radio-modem dependent
according to the specific model. Digital
modulation techniques are used.

During radio communication, the local radio
system handling the actual communication
controls the actual power transmission output
level. This output level may typically vary
(relative to the distance between the user
location and the cell transmission sites).

• When used properly, the design of this
hand-held wireless terminal complies with
U.S., Canadian, European and other
standards for protection from public
exposure to radio frequency (RF) magnetic
signals.

• This device has been tested and meets RF
exposure guidelines for hand held
operation pursuant to FCC OET Bulletin
65 Supplement C ed. 01-01, IEEE
1528/D1.2 (2003) and Industry Canada
RSS-102 (1999).

Installation Manual 11

Safety Precautions for Medical
Devices

For those persons using a pacemaker or
other medical device, please read the
following important safety notes:

• Though most electronic equipment and
critical medical devices are shielded against
radio-frequency signals, it is important to
realize the possibilities of potential
interference and to know the standard
precautions that may be taken.

Pacemakers

Industry standards recommend a minimum
separation of 15 cm (6 inches) between a
wireless phone-type device and a pacemaker
to prevent any potential problems.

Individuals using a pacemaker should:

• Always keep the NURIT more than 15 cm
(6 inches) from the pacemaker when using
the unit for cellular wireless
communication or when performing an
online transaction.

• Turn off the NURIT immediately and
disconnect it from the power supply if you
suspect any problem of interference.

Other Medical Devices

Consult the manufacturer of your medical
device to determine its level of shielding.
Depending on the proximity to certain
equipment, you may be asked not to use your
NURIT terminal or one of its accessories.

12 Installation Manual

Safety Precautions for Other
Electronic Devices

• Do not use your NURIT 8000 in an area of
potential explosive atmosphere, such as
fuel or chemical storage or transfer
facilities, or in any area where you would
be advised to turn off a vehicle’s engine.

•

Do not replace the battery pack or charge
the NURIT 8000 in an area of potential
explosive atmosphere.

• Do not use the NURIT 8000 in a known
blasting area.

•

Do not place the NURIT 8000 in the area
over a vehicle-equipped air bag.

• If the battery pack has been removed,
ensure that no metal objects come in
contact with its electrical contacts.

•

You are using a NURIT 8000 designed for
use with a built-in internal antenna. Do
not open the device with the intent of
tampering with the antenna system. Doing
so may damage the unit and violate FCC
(Ministry of Communications) regulations.

•

Radio frequency energy may affect
improperly installed or very sensitive
systems. Consult the specific device
manufacturer (or airline crew for possible
airborne operation) regarding typical
problems that may arise when using the
device. At the time of the publication of this
manual, it is known that use of all radio­type devices is prohibited while airborne.

Installation Manual 13

Specifications

Specification Details

Terminal: 8.4 VDC at 1.0 A

•

• AC/DC Adapter (Safety

Power

Dimensions

Paper Roll

Weight

Modem

Communication

Rate

Approvals

Approved)
Input: 100-240 VAC at
50/60 Hz (0.8 A)
Output : 8.4 VDC at 1.0 A

Height: 82 mm (3.23 in)

•

• Width: 108 mm (4.26 in)

• Depth: 230 mm (9.06 in)

• 57 mm x 38 mm

(2.25 in x 1.5 in)

• 10.5 mm (0.4 in) core diameter

• Terminal: 650 g (22.9 oz)

Including privacy shield,
battery pack and paper roll

• Shipping: 800g (28.2 oz.)
Not including this manual

• 56 Kbps (maximum)

• EMV Levels 1 and 2

• Visa PED (optional)

FCC Part 15 Class B

•

• CE

Note

Specifications are subject to
change without notice following
technological improvement of the
device and its components.

14 Installation Manual

Initial Setup

Unpacking the Box

To unpack the box:

1. Place the box right side up on a stable,

flat surface.

2. For secure models of the NURIT 8000,

verify that the Secure Device label that
seals the box is intact.

Figure 2 Secure Device Label

Caution

If the Secure Device label is
damaged or missing, do not open
the box. This could be an
indication of device tampering and
may affect the validity of the
warranty for the device. Notify
your Lipman distributor.

3. For secure models of the NURIT 8000,

peel off or cut through the Secure
Device label.

4. Open the front flap of the box.

Installation Manual 15