Verifone NURIT8000SWD User Manual

NURIT 8000

Wireless Palmtop

Solution

Installation Manual

Copyright Notice

Copyright© Lipman Electronic Engineering Ltd.
All rights reserved.

The content of this publication is for
informational purposes only and is subject to
change without notice. It does not represent a
commitment on the part of Lipman Electronic
Engineering Ltd.

No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval
system, or translated to any language in any
form by any means without the prior written
permission of Lipman.

Trademark Information

NURIT® is a registered trademark of Lipman
Electronic Engineering Ltd. All other product
and brand names contained in this manual are
trademarks of their respective owners.

Catalog Number

DOC00222 Orig.

Print Date

February 2004

Foreword

Thank you for purchasing the NURIT 8000
Wireless Palmtop Solution. You now own
one of the most advanced electronic point­of-sale (POS) terminals manufactured
today.

This manual provides basic installation
instructions. To fully utilize the features of
your NURIT 8000, and for general safety
purposes, it is recommended that you
familiarize yourself with this manual, the
terminal and any peripheral equipment or
accessories.

Figure 1 NURIT 8000 - General View

Installation Manual iii

Note

All graphic images in this manual
are for illustrative purposes only.
Different models of this terminal
may exist and may vary in
appearance according to country
of use or particular customer
requirements.
The basic installation procedure
is the same for most units.
The operation of the terminal is
application-dependent.

It is recommended that you store this
manual in a safe place for future reference.

Document Conventions

Note - Helpful hints and other important

information that will help you get better
use from your NURIT.

Caution

that, if not observed, could result in
damage to the NURIT or other equipment.

War ning - Failure to follow specific

procedures and practices may result in
personal injury.

- Information about procedures

iv Installation Manual

Tabl e o f C o n ten t s

Copyright Notice ........................................ ii

Trademark Information ................................. ii

Catalog Number ......................................... ii

Print Date................................................. ii

Foreword............................................. iii

Document Conventions ................................ iv

Product Regulatory Information ....................... 1

FCC Compliance Statement............................ 1

FCC Part 15 Requirements ............................. 1

FCC Part 68 Requirements ............................. 2

FCC Part 90 Requirements ............................. 4

In Canada: ................................................ 4

EU Directives Compliance Statement ................ 4

General Safety Instructions.......................... 5

Radio Frequency Energy Emission .................... 9

Safety Precautions for Medical Devices............. 10

Pacemakers .............................................10

Other Medical Devices.................................10

Safety Precautions for Other Electronic Devices ..11

Specifications ....................................... 12

Initial Setup .........................................13

Unpacking the Box .....................................13

Contents Checklist .....................................14

Selecting a Point-Of-Sale Location ..................17

Optional Accessories ...............................19

General Features ................................... 23

Installation Manual v

Installing the Battery Pack........................ 26

Battery Pack Maintenance ............................28

Connecting the NURIT 8000 to an AC Power Outlet. 30

Installing the External Modem.................... 32

Connecting the Car Adapter

Loading Paper in the Printer ...................... 35

Installing the Keypad Privacy Shield ............. 37

Installing a SIM or SAM Card

Installing the SIM/SAM Cardholder Compartment Cover .. 43

Installing a SIM Card in the TEL SIM Slot............ 45

Connecting Peripheral Devices....................... 47

Connecting a Cellular Headset ................... 49

General Care and Maintenance ..................... 50

Cleaning the NURIT 8000..............................50

Cleaning the Printer ...................................51

Maintenance Recommendations .....................52

Technical Assistance ...................................52

Shipping the NURIT 8000 .............................. 53

Troubleshooting.....................................54

Appendix A Using the Magnetic Card Reader....... 60

Appendix B

Installation Notes...................................63

Using the Smart Card Reader

........................ 33

.........................39

.......... 61

vi Installation Manual

List of Figures

Figure 1 NURIT 8000 - General View iii
Figure 2 Secure Device Label 13
Figure 3 NURIT 8000 – Box Contents 16
Figure 4 NURIT 8000 - Optional Accessories 19
Figure 5 NURIT 8000 - Top View 25
Figure 6 NURIT 8000 - Bottom View 25
Figure 7 Battery Pack Installation 26
Figure 8 Battery Pack Removal 27
Figure 9 AC Power Connection 30
Figure 10 External Modem Installation 32
Figure 11 Car Adapter Connection 33
Figure 12 Loading Paper in the Printer 36

Figure 13 Keypad Privacy Shield Installation 37
Figure 14 SIM/SAM Cardholder Locking-Clasp 41
Figure 15 SIM/SAM Card Installation 42
Figure 16 SIM/SAM Cardholder Compartment

Cover Installation 44

Figure 17 Void Label Installation 44
Figure 18 SIM Cardholder Ejection 45
Figure 19 SIM Card Installation 46
Figure 20 SIM Cardholder Insertion 46
Figure 21 Barcode Reader Connection 48

Figure 22 Cellular Headset Connection 49
Figure 23 Magnetic Card Reader 60
Figure 24 Smart Card Reader 61

Installation Manual vii

Product Regulatory
Information

Note

The following product regulatory
information and compliance
statements apply to all models of
the NURIT 8000x, where x
represents a suffix, such as S,
SVP, or Secure, designating the
specific security features of a
particular model.

Caution

Changes or modifications to this
device that are not expressly
approved by the party
responsible for compliance could
void the user's authority to
operate the equipment.

FCC Compliance Statement

Manufacturer: Lipman Electronic Engineering Ltd.
Model: NURIT 8000

FCC Part 15 Requirements

This equipment has been tested and found to
comply with the limits for Class B digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference when the
equipment is installed and operated in a
commercial environment.

Installation Manual 1

This equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation.

Operation of this equipment in a residential area
is likely to cause harmful interference in which
case the user will be required to correct the
interference at his/her own expense.

If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:

•

Reorient or relocate the receiving antenna.

• Increase the separation between the
equipment and the receiver.

• Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.

• Consult your dealer or an experienced
technician for help.

Connection of peripherals to this unit requires
the use of grounded, shielded cables to ensure
compliance with the class B limits.

FCC Part 68 Requirements

[Applicable when using optional NURIT 8000
docking station or NURIT 8000 external modem]

The FCC has established rules permitting this
device to be directly connected to the telephone
network. Standardized FCC Part 68 compliant
telephone line cords and modular jacks are used
for these connections. This equipment should not
be used on party or coin lines.

2 Installation Manual

If this device is malfunctioning, it may be causing
harm to the telephone network; this device
should be disconnected until the source of the
problem can be determined and until repair has
been made. If this is not done, the telephone
company may temporarily disconnect service.

The telephone company may make changes in its
technical operations and procedures; if such
changes affect the compatibility or use of this
device, the telephone company is required to
give adequate notice of the changes. You will be
advised to file a complaint with the FCC.

If the telephone company requests information
on what equipment is connected to their lines,
inform them of:

• The telephone number to which this unit is
connected

• The AC Ringer Equivalence Number: 00B

• The USOC jack required: RJ-11C

•

The FCC Registration number: (See the
underside of the unit and/or applicable unit
documentation for this number.)

The Ringer Equivalence Number (REN) is used
to determine how many devices can be
connected to your telephone line. In most areas,
the sum of the RENs of all devices on any one
line should not exceed five (5). If too many
devices are attached, they may not ring properly.
To be certain of the number of devices that may
be connected to the line, as determined by the
total RENs, contact the telephone company to
determine the maximum REN for the calling
area.

Installation Manual 3

FCC Part 90 Requirements

This device may contain a radio transceiver
module, (FCC ID number is located on the
bottom of the terminal), operating under Part 90
of the FCC rules in a licensed part of the radio
spectrum. Qualified personnel must perform
service or repairs to the radio portion of this
device. Any unauthorized modification to the
radio module, shielding, or antenna system may
void the user’s authority to operate this device.

This device has been tested and meets RF
exposure guidelines for hand held operation
pursuant to FCC OET Bulletin 65 Supplement C
ed. 01-01, IEEE 1528/D1.2 (2003) and Industry
Canada RSS-102 (1999).

In Canada:

This digital apparatus does not exceed the class
B limits for radio noise emissions from digital
apparatuses set forth in the Radio Interference
Regulations of the Canadian Department of
Communications.

Cet appareil numérique n'émet pas de bruits
radioélectriques dépassant les limites applicables
aux appareils de la classe B, déterminée par la
Réglementation d’Interférence Radio du
Ministère canadien des Communications.

EU Directives Compliance Statement

This product complies with the requirements of
applicable EU Council Directives.

Caution

Any unauthorized modification of
the equipment may void the
user’s authority to operate this
device.

4 Installation Manual

General Safety Instructions

Warning

Failure to observe these
instructions may result in severe
personal injury or damage to the
NURIT 8000 or other equipment.

Note

These safety instructions are
based in general on those
provided by Underwriters
Laboratories (UL) Inc. U.S.A.

When using the NURIT 8000 or any
associated device, the following basic
safety precautions should always be
observed to reduce the risk of fire, electric
shock, or personal injury:

• Read and make sure you understand all
instructions.

• Follow all warnings and instructions
marked on the device and in this manual.

•

Disconnect the device from the power
supply and any peripherals before
cleaning.

• Do not use liquid or aerosol cleaners. Use
a damp cloth for cleaning and/or a soft
brush.

•

Do not use the device near water,
especially when using the AC/DC Power
Adapter or external modem.

• Never spill any liquid on the device.

Installation Manual 5

•

Place the device in a stable position on a
solid surface. When operated hand-held,
grasp the device securely. Serious
damage may result if the device falls.

•

The optimal operational position for the
terminal is hand-held at an angle of
approximately 30

o

. The terminal is also
designed for optimal tabletop usage.
Keep the terminal a short distance from
your body.

•

Do not cover slots and openings of the
device. They may be provided for
ventilation and protection against
overheating. Never place the device near
radiators, or in a place where proper
ventilation is not provided.

•

Use only the power source as marked on
the device. If you are not sure of the type
of the power supplied to your location,
consult your dealer or local power
company.

• Do not place objects on the power cord.
Install the device where no one can step
on the cord.

• Do not overload wall outlets and
extension cords as this can result in the
risk of fire or electric shock.

•

Never push objects into the device
through slots (other than those
specifically intended for the stylus,
magnetic stripe or smart cards, or
SAM/SIM cards), as this may result in
fire or electric shock.

6 Installation Manual

•

To reduce the risk of electric shock, do
not disassemble any of the equipment or
accessories referred to in this manual. If
required, take the equipment to a
qualified service representative. Opening
or removing covers may expose you to
dangerous voltages or other risks.
Incorrect reassembly can cause electric
shock.

• Disconnect the device from the power
supply and any peripherals and refer to
qualified service personnel under the
following conditions:

• The power supply cable or plug is

damaged or frayed.

• Liquid has been spilled into the

device.

•

The device has been exposed to
rain or water.

• The device does not work

normally, when following the
operating instructions.

•

The device has been dropped or
damaged.

• The device exhibits a distinct

change in performance.

• When using the NURIT 8000 optional
docking station and/or external modem
during thunderstorms, disconnect the
telephone line, if possible. There may be
a remote risk of electric shock from
lightning.

• Never install telephone wiring during a
lightning storm.

Installation Manual 7

•

Never install telephone jacks in wet
locations unless the jack is specifically
designed for wet locations.

• Never touch non-insulated telephone
wires or equipment unless the telephone
line has been disconnected at the
network interface.

• Use caution when installing or modifying
telephone lines.

• When in the vicinity of a gas leak, do not
use the NURIT 8000, a standalone
telephone or a telephone connected to a
POS terminal or docking station to report
the leak.

• Take care when installing an internal
battery pack. If installed incorrectly, it
may explode. Use only a Lipman supplied
battery pack. Discard used battery packs
according to local regulations.

8 Installation Manual

Radio Frequency Energy Emission

Your NURIT 8000 may contain a transmitter
and receiver that emit radio frequency (RF)
energy. The actual frequency range used by
the NURIT 8000 is radio-modem dependent
according to the specific model. Digital
modulation techniques are used.

During radio communication, the local radio
system handling the actual communication
controls the actual power transmission
output level. This output level may typically
vary (relative to the distance between the
user location and the cell transmission
sites).

• When used properly, the design of this
hand-held wireless terminal complies
with U.S., Canadian, European and other
standards for protection from public
exposure to radio frequency (RF)
magnetic signals.

• This device has been tested and meets
RF exposure guidelines for hand held
operation pursuant to FCC OET Bulletin
65 Supplement C ed. 01-01, IEEE
1528/D1.2 (2003) and Industry Canada
RSS-102 (1999).

Installation Manual 9

Safety Precautions for Medical
Devices

For those persons using a pacemaker or
other medical device, please read the
following important safety notes:

• Though most electronic equipment and
critical medical devices are shielded
against radio-frequency signals, it is
important to realize the possibilities of
potential interference and to know the
standard precautions that may be taken.

Pacemakers

Industry standards recommend a minimum
separation of 15 cm (6 inches) between a
wireless phone-type device and a pacemaker
to prevent any potential problems.

Individuals using a pacemaker should:

• Always keep the NURIT more than 15 cm
(6 inches) from the pacemaker when
using the unit for cellular wireless
communication or when performing an
online transaction.

• Turn off the NURIT immediately and
disconnect it from the power supply if
you suspect any problem of interference.

Other Medical Devices

Consult the manufacturer of your medical
device to determine its level of shielding.
Depending on the proximity to certain
equipment, you may be asked not to use
your NURIT terminal or one of its
accessories.

10 Installation Manual

Safety Precautions for Other
Electronic Devices

• Do not use your NURIT 8000 in an area
of potential explosive atmosphere, such
as fuel or chemical storage or transfer
facilities, or in any area where you would
be advised to turn off a vehicle’s engine.

• Do not replace the battery pack or
charge the NURIT 8000 in an area of
potential explosive atmosphere.

• Do not use the NURIT 8000 in a known
blasting area.

• Do not place the NURIT 8000 in the area
over a vehicle-equipped air bag.

•

If the battery pack has been removed,
ensure that no metal objects come in
contact with its electrical contacts.

• You are using a NURIT 8000 designed for
use with a built-in internal antenna. Do
not open the device with the intent of
tampering with the antenna system.
Doing so may damage the unit and
violate FCC (Ministry of
Communications) regulations.

• Radio frequency energy may affect
improperly installed or very sensitive
systems. Consult the specific device
manufacturer (or airline crew for
possible airborne operation) regarding
typical problems that may arise when
using the device. At the time of the
publication of this manual, it is known
that use of all radio-type devices is
prohibited while airborne.

Installation Manual 11

Specifications

Specification Details

Terminal: 8.4 VDC at 1.0 A

•

• AC/DC Adapter (Safety

Powe r

Dimensions

Paper Rol l

Weight

Modem

Communication

Rate

Approvals

Approved)
Input: 100-240 VAC at
50/60 Hz (0.8 A)
Output : 8.4 VDC at 1.0 A

Height: 82 mm (3.23 in)

•

• Width: 108 mm (4.26 in)

• Depth: 230 mm (9.06 in)

• 57 mm x 38 mm

(2.25 in x 1.5 in)

• 10.5 mm (0.4 in) core diameter

• Terminal: 650 g (22.9 oz)

Including privacy shield,
battery pack and paper roll

• Shipping: 800g (28.2 oz.)
Not including this manual

• 56 Kbps (maximum)

• EMV Levels 1 and 2

• Visa PED (optional)

FCC Part 15 Class B

•

• CE

Note

Specifications are subject to
change without notice following
technological improvement of the
device and its components.

12 Installation Manual

Initial Setup

Unpacking the Box

To unpack the box:

1. Place the box right side up on a stable,
flat surface.

2. For secure models of the NURIT 8000,
verify that the Secure Device label
that seals the box is intact.

Figure 2 Secure Device Label

Caution

If the Secure Device label is
damaged or missing, do not open
the box. This could be an
indication of device tampering
and may affect the validity of the
warranty for the device. Notify
your Lipman distributor.

3. For secure models of the NURIT 8000,
peel off or cut through the Secure
Device label.

4. Open the front flap of the box.

Installation Manual 13

5. Open the top cover of the box.

6. Carefully remove the contents of the

box.

Note

It is recommended that you save
the box for future repacking or
moving of the terminal.

Carefully inspect the contents for any

7.

damaged or missing components.

Note

Lipman has taken all measures to
provide you with a complete
device. If shipping damage is
evident, file a claim with the
shipping company. Notify your
Lipman distributor concerning
this damage, and if any
components are missing.

Contents Checklist

The following items should be found inside
the box:

Note

Any one or more of the included
accessories may be already
attached to the terminal.

• NURIT 8000 Wireless Palmtop Solution

•

AC/DC Power Adapter (boxed)

•

Lithium-ion Battery Pack

• Paper Roll Spindle

• Thermal Paper Roll

14 Installation Manual