Verifone NURIT8000SSQ, NURIT8000SS4 User Manual
NURIT 8000
Wireless
Palmtop Solution
Installation Manual
Copyright
Copyright© Lipman Electronic Engineering Ltd.
All rights reserved.
The content of this publication is for informational purposes
only and is subject to change without notice. It does not
represent a commitment on the part of Lipman Electronic
Engineering Ltd.
No part of this publication may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated to any
language in any form by any means without the prior written
permission of Lipman.
Trademark Information
NURIT® is a registered trademark of Lipman Electronic
Engineering Ltd. All other product and brand names contained
in this manual are trademarks of their respective companies.
Catalog Number
DOC095EN02-A
Print Date
November 2005
Foreword
Thank you for purchasing the NURIT 8000 Wireless Palmtop
Solution. You now own one of the most advanced electronic
point-of-sale (POS) terminals manufactured today.
This manual provides basic installation instructions. To fully
utilize the features of your NURIT
purposes, it is recommended that you familiarize yourself with
this manual, the terminal and any peripheral equipment or
accessories.
It is recommended that you store this manual in a safe place for
future reference.
All graphic images in this manual are for
illustrative purposes only.
Different models of this terminal may exist and
may vary in appearance according to country of
use or particular customer requirements.
The basic installation procedure is the same for
most units.
The operation of the terminal is applicationdependent.
Document Conventions
War nin g - Failure to follow specific procedures and practices
may result in personal injury.
Caution - Failure to follow specific procedures and practices
may result in damage to the NURIT device or other equipment.
Note - Helpful hints and other important information about the
use of the NURIT device.
8000, and for general safety
Note
Installation Manual iii
Table of Contents
Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Document Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . iii
1. Product Regulatory Information. . . . . . . . . . . . . . . . . . . . 1
2. General Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . 4
Radio Frequency Energy Emission. . . . . . . . . . . . . . . . . . . . 6
Safety Precautions for Medical Devices . . . . . . . . . . . . . . . . 7
3. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4. Initial Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Unpacking the Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Contents Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Selecting a Point-Of-Sale Location . . . . . . . . . . . . . . . . . . .12
Wireless LAN (WiFi) Terminals . . . . . . . . . . . . . . . . . . . . . .13
5. Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . .14
6. General Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
7. Installing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . .18
Battery Pack Maintenance. . . . . . . . . . . . . . . . . . . . . . . . .19
8. Connecting the NURIT 8000 to an AC Power Outlet . . . . . . .20
Battery Pack Charge Status . . . . . . . . . . . . . . . . . . . . . . . .20
9. Installing the External Modem. . . . . . . . . . . . . . . . . . . . .21
10. Connecting the Car Adapter . . . . . . . . . . . . . . . . . . . . . .22
11. Loading Paper in the Printer . . . . . . . . . . . . . . . . . . . . . .23
12. Installing the Keypad Privacy Shield . . . . . . . . . . . . . . . . .24
13. Installing a SIM, SAM, or SD/MMC Card . . . . . . . . . . . . . . .25
Electronic Cards Configurations . . . . . . . . . . . . . . . . . . . . .26
Installing SIM and SAM Cards in the
Electronic Cards Compartment: . . . . . . . . . . . . . . . . . . . . .27
Installing a SIM Card in the TEL SIM Slot. . . . . . . . . . . . . . . .28
Installing an SD/MMC Card . . . . . . . . . . . . . . . . . . . . . . . .30
Installing the Electronic Cards Compartment Cover . . . . . . . . 31
14. Connecting Peripheral Devices . . . . . . . . . . . . . . . . . . . .33
15. Connecting a Cellular Headset . . . . . . . . . . . . . . . . . . . .34
16. Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . .35
Technical Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Installation Manual v
Cleaning the NURIT 8000 . . . . . . . . . . . . . . . . . . . . . . . . . 36
Cleaning the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Shipping the NURIT 8000 . . . . . . . . . . . . . . . . . . . . . . . . . 37
17. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Appendix A: Using the Magnetic Card Reader . . . . . . . . . . 42
Appendix B: Using the Smart Card Reader . . . . . . . . . . . . 43
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . 44
vi Installation Manual
List of Figures
Figure 4-1 Secure Device Label . . . . . . . . . . . . . . . . . . . . . 9
Figure 4-2 NURIT 8000 - Box Contents. . . . . . . . . . . . . . . . .11
Figure 5-1 NURIT 8000 - Optional Accessories. . . . . . . . . . . .14
Figure 6-1 NURIT 8000 - General Features . . . . . . . . . . . . . .17
Figure 7-1 Battery Pack Installation . . . . . . . . . . . . . . . . . .18
Figure 7-2 Battery Pack Removal . . . . . . . . . . . . . . . . . . . .18
Figure 8-1 AC Power Connection . . . . . . . . . . . . . . . . . . . .20
Figure 9-1 External Modem Installation. . . . . . . . . . . . . . . .21
Figure 10-1 Car Adapter Connection . . . . . . . . . . . . . . . . . .22
Figure 11-1 Loading Paper in the Printer. . . . . . . . . . . . . . . .23
Figure 12-1 Keypad Privacy Shield Installation . . . . . . . . . . . .24
Figure 13-1 Electronic Cards Configurations . . . . . . . . . . . . .26
Figure 13-2 SIM/SAM Cardholder Locking-Clasp . . . . . . . . . . .27
Figure 13-3 SIM/SAM Card Installation . . . . . . . . . . . . . . . . .28
Figure 13-4 SIM Cardholder Ejection . . . . . . . . . . . . . . . . . .29
Figure 13-5 SIM Card Installation . . . . . . . . . . . . . . . . . . . . .29
Figure 13-6 SIM Cardholder Insertion . . . . . . . . . . . . . . . . . .29
Figure 13-7 Positioning the SD/MMC Card . . . . . . . . . . . . . . .30
Figure 13-8 Inserting the SD/MMC Card. . . . . . . . . . . . . . . . .31
Figure 13-9 Installing the Electronic Cards Compartment Cover 32
Figure 13-10 Void Label Installation . . . . . . . . . . . . . . . . . . .32
Figure 14-1 Peripheral Device Connection. . . . . . . . . . . . . . . 33
Figure 15-1 Cellular Headset Connection . . . . . . . . . . . . . . .34
Figure A-1 Magnetic Card Reader . . . . . . . . . . . . . . . . . . . .42
Figure B-1 Smart Card Reader . . . . . . . . . . . . . . . . . . . . . .43
Installation Manual vii
1. Product Regulatory Information
Note
The following product regulatory information
and compliance statements apply to all models
of the NURIT 8000x, where x represents a
suffix, such as S, SVP, or Secure, designating the
specific security features of a particular model.
Caution
Changes or modifications to this device that are
not expressly approved by the party responsible
for compliance could void the user's authority to
operate the equipment.
FCC Compliance Statement
Manufacturer: Lipman Electronic Engineering Ltd.
Model: NURIT 8000
FCC Part 15 Requirements
This equipment has been tested and found to comply with the
limits for Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
installed and operated in a commercial environment.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his/her own expense.
Installation Manual 1
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult your dealer or an experienced technician for help.
Connection of peripherals to this unit requires the use of
grounded, shielded cables to ensure compliance with the
class
B limits.
FCC Part 68 Requirements
[Applicable when using optional NURIT 8000 docking station or
8000 external modem]
NURIT
The FCC has established rules permitting this device to be
directly connected to the telephone network. Standardized FCC
Part 68 compliant telephone line cords and modular jacks are
used for these connections. This equipment should not be used
on party or coin lines.
If this device is malfunctioning, it may be causing harm to the
telephone network; this device should be disconnected until the
source of the problem can be determined and until repair has
been made. If this is not done, the telephone company may
temporarily disconnect service.
The telephone company may make changes in its technical
operations and procedures; if such changes affect the
compatibility or use of this device, the telephone company is
required to give adequate notice of the changes. You will be
advised to file a complaint with the FCC.
If the telephone company requests information on what
equipment is connected to their lines, inform them of:
• The telephone number to which this unit is connected
• The AC Ringer Equivalence Number: 00B
• The USOC jack required: RJ-11C
• The FCC Registration number: O2SNURIT8000SSQ
2 Installation Manual
The Ringer Equivalence Number (REN) is used to determine
how many devices can be connected to your telephone line.
In most areas, the sum of the RENs of all devices on any one
line should not exceed five (5). If too many devices are
attached, they may not ring properly. To be certain of the
number of devices that may be connected to the line, as
determined by the total RENs, contact the telephone company
to determine the maximum REN for the calling area.
FCC Part 24 Requirements
This device may contain a radio transceiver module, (FCC ID
number is located on the bottom of the terminal), operating
under Part 24 of the FCC rules in a licensed part of the radio
spectrum. Qualified personnel must perform service or repairs
to the radio portion of this device. Any unauthorized
modification to the radio module, shielding, or antenna system
may void the user's authority to operate this device.
This device has been tested and meets RF exposure guidelines
for hand held operation pursuant to FCC OET Bulletin 65
Supplement C ed. 01-01, IEEE 1528/D1.2 (2003) and Industry
Canada RSS-102 (1999).
In Canada
This digital apparatus does not exceed the class B limits for
radio noise emissions from digital apparatuses set forth in the
Radio Interference Regulations of the Canadian Department of
Communications.
Cet appareil digital n'émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils de la classe B,
déterminée par la Réglementation d'Interférence Radio du
Ministère Canadien des Communications.
IC: 4804A-N8000SSQ
EU Directives Compliance Statement
This product complies with the requirements of applicable EU
Council Directives.
Installation Manual 3
2. General Safety Instructions
War nin g
Failure to observe these instructions may result
in severe personal injury or damage to the
NURIT 8000 or other equipment.
Note
These safety instructions are based in general
on those provided by Underwriters Laboratories
(UL) Inc. U.S.A.
When using the NURIT 8000 or any associated device, the
following basic safety precautions should always be observed to
reduce the risk of fire, electric shock, or personal injury.
• Read and make sure you understand all instructions.
• Follow all warnings and instructions marked on the device
and in this manual.
• Disconnect the device from the power supply and any
peripherals before cleaning.
• Do not use liquid or aerosol cleaners. Use a damp cloth for
cleaning and/or a soft brush.
• Do not use the device near water, especially when using
the AC/DC Power Adapter or external modem.
• Never spill any liquid on the device.
• Place the device in a stable position on a solid surface.
When operated hand-held, grasp the device securely.
Serious damage may result if the device falls.
• The optimal operational position for the terminal is hand-
held at an angle of approximately 30°. The terminal is also
designed for optimal tabletop usage. Keep the terminal a
short distance from your body.
• Do not cover slots and openings of the device. They may
be provided for ventilation and protection against
overheating. Never place the device near radiators, or in a
place where proper ventilation is not provided.
• Do not place objects on the power cord. Install the device
where no one can step on the cord.
4 Installation Manual
• Use only the power source as marked on the device. If you
are not sure of the type of the power supplied to your
location, consult your dealer or local power company.
• Do not overload wall outlets and extension cords as this
can result in the risk of fire or electric shock.
• Never push objects into the device through slots (other
than those specifically intended for the stylus, magnetic
stripe or smart cards, SAM/SIM cards, or SD/MMC card),
as this may result in fire or electric shock.
• To reduce the risk of electric shock, do not disassemble
any of the equipment or accessories referred to in this
manual. If required, take the equipment to a qualified
service representative. Opening or removing covers may
expose you to dangerous voltages or other risks. Incorrect
reassembly can cause electric shock.
• Take care when installing an internal battery pack. If
installed incorrectly, it may explode. Use only a Lipman
supplied battery pack. Discard used battery packs
according to local regulations.
• Disconnect the device from the power supply and any
peripherals and refer to qualified service personnel under
the following conditions:
• The power supply cable or plug is damaged or frayed.
• Liquid has been spilled into the device.
• The device has been exposed to rain or water.
• The device does not work normally, when following
the operating instructions.
• The device has been dropped or damaged.
• The device exhibits a distinct change in performance.
• When using the NURIT 8000 optional docking station and/
or external modem during thunderstorms, disconnect the
telephone line, if possible. There may be a remote risk of
electric shock from lightning.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the
jack is specifically designed for wet locations.
• Use caution when installing or modifying telephone lines.
• Never touch non-insulated telephone wires or equipment
unless the telephone line has been disconnected at the
network interface.
Installation Manual 5
• When in the vicinity of a gas leak, do not use the
NURIT 8000, a standalone telephone or a telephone
connected to a NURIT 8000 docking station to report the
leak.
• Do not use the NURIT 8000 in an area of potential
explosive atmosphere, such as fuel or chemical storage or
transfer facilities, or in any area where you would be
advised to turn off a vehicle's engine.
• Do not replace the battery pack or charge the NURIT 8000
in an area of potential explosive atmosphere.
• Do not use the NURIT 8000 in a known blasting area.
• Do not place the NURIT 8000 in the area over a vehicle-
equipped air bag.
• If the battery pack has been removed, ensure that no
metal objects come in contact with its electrical contacts.
• The NURIT 8000 is designed for use with a built-in
internal antenna. Do not open the device with the intent of
tampering with the antenna system. Doing so may damage
the unit and violate FCC (Ministry of Communications)
regulations.
Radio Frequency Energy Emission
Your NURIT 8000 may contain a transmitter and receiver that
emit radio frequency (RF) energy. The actual frequency range
used by the NURIT 8000 is radio-modem dependent according
to the specific model. Digital modulation techniques are used.
During radio communication, the local radio system handling
the actual communication controls the actual power
transmission output level. This output level may typically vary
(relative to the distance between the user location and the cell
transmission sites).
RF energy may affect some electronic systems. Consult the
specific device manufacturer (or airline crew for possible
airborne operation) regarding permission to use this device
while airborne and associated problems. It is currently known
that use of all radio-type devices is prohibited while airborne.
• When used properly, the design of this handheld wireless
terminal complies with U.S., Canadian, European and
other standards for protection from public exposure to RF
magnetic signals.
6 Installation Manual
• This device has been tested and meets RF exposure
guidelines for hand held operation pursuant to FCC OET
Bulletin 65 Supplement C ed. 01-01, IEEE 1528/D1.2
(2003) and Industry Canada RSS-102 (1999).
War nin g
The NURIT 8000 must be located at least 20 cm
from all persons, and must not be co-located or
operated in conjunction with any other antenna
or transmitter.
Safety Precautions for Medical Devices
For those persons using a pacemaker or other medical device,
please read the following important safety notes:
• Though most electronic equipment and critical medical
devices are shielded against radio-frequency signals, it is
important to realize the possibilities of potential
interference and to know the standard precautions that
may be taken.
Pacemakers
Industry standards recommend a minimum separation of 15 cm
(6 inches) between a wireless phone-type device and a
pacemaker to prevent any potential problems.
Individuals using a pacemaker should:
• Always keep the NURIT 8000 terminal more than 15 cm
(6 inches) from the pacemaker when using the unit for
cellular wireless communication or when performing an
online transaction.
• Turn off the NURIT 8000 terminal immediately and
disconnect it from the power supply if you suspect any
problem of interference.
Other Medical Devices
Consult the manufacturer of your medical device to determine
its level of shielding. Depending on the proximity to certain
equipment, you may be asked not to use your NURIT terminal
or one of its accessories.
Installation Manual 7
3. Specifications
Specification Details
• Terminal: 8.4 VDC at 1.0 A
Power
Dimensions
Paper R oll
Weight
Modem
Communication
Rate
Approvals
Specifications are subject to change without
notice following technological improvement of
the device and its components.
• AC/DC Adapter (Safety Approved)
Input: 100-240 VAC at 50/60 Hz (0.8 A)
Output: 8.4 VDC at 1.0 A
• Height: 55 mm (2.17 in)
• Width: 91 mm (3.58 in)
• Depth: 210 mm (8.27 in)
• 57 mm x 38 mm (2.25 in x 1.5 in)
• 10.5 mm (0.4 in) core diameter
• Terminal: 600 g (21.2 oz)
Including privacy shield, battery pack and
paper roll
• Shipping: 800g (28.2 oz)
Not including this manual
• 56 Kbps (maximum)
• EMV Levels 1 and 2
• Visa PED (optional)
• FCC Part 15 Class B
• CE
Note
8 Installation Manual
Loading...