Ventrac ET200 Operator's Manual
OWNER/OPERATOR’S
MAN UAL & PARTS LIST
ET200
TURBINE BLOWER
Re vised 10/23/14
09.10006
Orrville, OH
www.ventrac.com
TO THE OWNER
Product Identification
If you need to contact an Authorized Ventrac Dealer for information on servicing your product,
always provide the Product Model and Serial numbers.
Please fill in the following information for future reference. See picture below to find the
location of the identification number. Record them in the spaces provided below.
Date of Purchase: Month _________________ Day ___________ Year ___________________
Dealer: _______________________________________________________________________
Dealer Address: ________________________________________________________________
________________________________________________________________
Dealer Phone Number: __________________________________________________________
Dealer FAX Number: ____________________________________________________________
Model # (A): _______________________
Serial # (B): ________________________
Affix Part/Serial Number label here
Venture Products Inc. reserves the right to make changes
in design or specifications without obligation to make like
changes on previously manufactured products.
ii
TABLE OF CONTENTS
INTRODUCTION SECTION A
Description and Specifications...........................A-1
SAFETY SECTION B
Safety Symbols ..................................B-1
Decals .....................................B-2&3
General Safety Procedures ............................B-4
Safety Operation & Techniques ..........................B-5
SETUP & OPERATION SECTION C
Attaching......................................C-1
Detaching .....................................C-1
Operating Tips ...................................C-2
MAINTENANCE/ADJUSTMENTS SECTION D
Maintenance ....................................D-1
Adjustment.....................................D-2
PARTS & ILLUSTRATED DRAWINGS SECTION E
Main Frame & Blower Drive ..........................E-1&2
Shields, Stand, & Wheel Mount ........................E-3&4
Hydraulic Motor ................................E-5&6
Blower Mount & Discharge Nozzle ......................E-7&8
WARRANTY
iii
INTRODUCTION
Product Description
ET200 Turbine Blower
The ET200 Turbine Blower is designed to blow a large volume of air using a radial fin
turbine design. Because of this design, the Turbine blower is much quieter than a
conventional leaf blower. It can be used effectively to blow leaves, light snow, and
debris from sidewalks, parking lots and other areas requiring debris removal. It can also
be used to remove standing water and to dry wet surfaces.
Blower Features:
Minute-MountTMhook up
•
360 degree continuous nozzle rotation
•
Nozzle rotation is hydraulicly controlled from the tractor seat
•
•
Easy connect hydraulic quick couplers
•
Single front caster wheel to provide smooth ground contour transitions
•
Front bumper to protect the nozzle from being damaged
•
Adjustable Jackstand for easy attaching and detaching
Ventrac ET200 Specifications
Overall Height ..........................34inches (86.5 cm)
Overall Length...........................76inches (193 cm)
Overall Width ...........................27inches (68.5 cm)
Weight .............................250pounds (113.5 kg)
Nozzle Size ..............................12-1/2” (32 cm)
Wind Speed at nozzle.......................125mph(201km/h)
A-1
SAFETY
ATTENTION:
This symbol identifies potential health and
safety hazards. It marks safety
precautions. Your safety and the safety of
others is involved.
SIGNAL WORD DEFINITIONS
Indicates an imminently hazardous
situation which, if not avoided, will result in
death or serious injury. This signal word is
limited to the most extreme cases.
Indicates a potentially hazardous situation
which, if not avoided, could result in death
or serious injury.
Indicates a potentially hazardous situation
which, if not avoided, may result in minor
or moderate injury and/or property
damage. It may also be used to alert
against unsafe practices.
B-1
SAFETY
The following decals must be maintained on your Ventrac turbine blower. If any decals
are faded or missing, contact your dealer promptly for replacements.
A
D
B
C
E
F G
H
B-2
SAFETY
Decal
A
B
C
D
E
F
G
H
Page &
Location
E-1, #29 Danger - Shield Missing 00.0062
E-1, #36
Warning - Do Not Reach 00.0219
E-3, #26
E-3, #16 (2) Warning Moving Parts 00.0216
E-3, #23 Read Owners Manual 00.0217
E-3, #24 General Safety 00.0220
E-7, #17 America & Safety First 07.22103
E-7, #18 Warning - Eye Protection 07.22107
E-7, #19 Warning - Ear Protection 07.22106
Description Part Number
B-3
Loading...