Vent-Axia ATQ 400-14C, ATQ 200-12C, ATQ 125-12C, ATQ 100-12C, ATQ 250-12C Installation And Wiring Instructions
...
ACOUSTIC TWIN FAN
Installation and Wiring Instructions
Stock Ref. N°
ATQ 100-12C ATQ 200-12C ATQ 400-14C
ATQ 125-12C ATQ 250-12C ATQ 500-14C
ATQ 150-12C ATQ 315-12LC
ATQ 160-12C ATQ 315-14HC
220-240V/1/50Hz
READ INSTRUCTIONS IN CONJUNCTION WITH ILLUSTRATIONS
READ AND SAVE THESE INSTRUCTIONS
Installation and Wiring Instructions for ATQ Acoustic Fan
IMPORTANT:
READ THESE INSTRUCTIONS BEFORE COMMENCING THE INSTALLATION
DO NOT install this product in areas where the following may be present or occur:
• Excessive oil or a grease laden atmosphere.
• Corrosive or flammable gases, liquids or vapours.
• Ambient temperatures higher than 50°C or less than –15°C.
• Relative humidity above 95%
• Possible obstructions which would hinder the access or removal of the fan.
• Sudden ductwork bends or transformations close to the fan.
SAFETY AND GUIDANCE NOTES
A. All wiring must be in accordance with the current I.E.E. Regulations, or the appropriate standards of your country.
B. The fan should be provided with a local double pole isolator switch having a contact separation of at least 3mm.
C. Ensure that the mains supply (Voltage, Frequency and Phase) complies with the rating label.
D. The fan should only be used in conjunction with the appropriate Vent-Axia products.
E. It is recommended that the connection to the terminal box is made with flexible cable/conduit.
F. The fan should not be sited within 600mm horizontally of/or 2250mm vertically of a bath/shower tray, in
accordance with the current I.E.E. Regulations for bathrooms.
G. When the fan is used to remove air from a room containing a fuel-burning appliance, ensure that the air
replacement is adequate for both the fan and the fuel-burning appliance.
H. If the fan is used to supply air into a room, the installer must ensure that the fan intake is located a minimum of
600mm from any flue outlet.
I. This fan is designed as an inline duct fan to be positioned between lengths of ducting. Short duct runs terminating
within 1.5m must incorporate suitable guards unless the fan is mounted higher than 2.3m.
J. This fan should not to be used where it is liable to be subject to direct water spray from hoses etc.
K. Where ducted fans are used to handle moisture-laden air, a condensation trap should be fitted. Horizontal ducts
should be arranged to slope slightly downwards away from the fan.
L. Certain applications may require the installation of sound attenuation material to achieve the sound levels
required. An auto transformer speed controller is also recommended.
INSTALLATION
FAN MOUNTING
1. The fan is only suitable for mounting horizontally.
2. The fan may be mounted for bottom access by making the following modifications to the shutters:
a). Remove the lid of the fan and the retaining screws of the outer shutter brackets.
b). Move the nylon bushes to the vacant holes in all shutter brackets.
c). Reassemble the shutter flaps into the nylon bushes.
d). Refit the retaining screws of the outer brackets and refit the lid of the fan.
3. Securely mount the fan using the holes in the flanges and use the appropriate drop rods, bolts, anti-vibration
mounts etc.
4. Flexible connections should be used at the fan inlet and outlet.
5. Ensure that there is adequate clearance for accessing the fan and removal of the access panel if appropriate.
WIRING
WARNING: THE FAN AND ANCILLARY CONTROL EQUIPMENT MUST BE ISOLATED FROM
THE POWER SUPPLY DURING THE INSTALLATION / OR MAINTENANCE.
THE EQUIPMENT MUST BE EARTHED
1. Select and follow the appropriate wiring diagram (Figs. 2-5).
2. Check that all connections have been made correctly. Ensure that all terminal screws and cable clamps are
securely fastened.
3. The cable entry must be made using a suitable grommet or cable gland.
4. Switch the mains supply on and check the system is operating correctly.
2
ROUTINE INSPECTION AND MAINTENANCE
ISOLATE THE UNIT FROM THE POWER SUPPLY AND ENSURE THAT IT CANNOT BE ACCIDENTALLY SWITCHED BACK ON
1. At intervals appropriate to the installation, the fan should be inspected and cleaned to ensure there is no build up
of dirt or other deposits on the impeller or the motor (Caution – do not dislodge any balance weights which may
be fitted to the impeller). If the fan is handling dust laden air, it is recommended that a filter is installed.
2. All Vent-Axia acoustic fan motors are fitted with sealed for life bearings and do not require lubrication.
OVERHEATING PROTECTION
The fan motor is fitted with Standard Thermal Overload Protection. This will automatically switch the fan Off in the
event of a fault condition. If this occurs, isolate the fan, check for any obstruction, leave the fan for a short time for
the motor to cool before reconnecting the power supply. If the fault reoccurs, isolate the power supply and call a
service engineer.
Fig. 1
DIMENSIONS (mm)
ATQ100-12C
ATQ125-12C
ATQ150-12C
ATQ160-12C
ATQ200-12C
ATQ250-12C
ATQ315-12LC
ATQ315-14HC
ATQ400-14C
ATQ500-14C
A
BC E
312
312
312
312
362
362
477
517
517
672
635
635
635
770
770
880
1100
1100
1300
171635
171
171
171
203
233
258
295
253
357
510
510
510
610
610
760
810
810
Ø
E
20
FLANGE
20
FLANGE
PLAN
= =
A
B
97510
122
147
157
197
247
312
312
397
4971060
Kg
(approx)
25
25
25
25
35
40
50
70
75
120
D
ELEVATION
3
Fig. 2
ATQ ACOUSTIC SINGLE PHASE FAN WIRING DETAILS
STOCK REFERENCE NUMBERS:
ATQ 100-12C, ATQ 125-12C, ATQ 150-12C, ATQ 160-12C, ATQ 200-12C
ATQ 250-12C, ATQ 315-12LC, ATQ 315-14HC, ATQ 400-14C.
1 Phase Supply
(220-240V 50Hz)
L3
TK
TK
L
N
U1
U2
N
L1
L2
L3
E
TK
TK
TK
TK
L
N
U1
U2
E
N
L1
L3
L2
TK
TK
L2
L1
240V
N
LN
~
E
E LN
ABDCE
INPUT
FAN 2
OUTPUT
240V
INPUT
24V AC
(ITC-DS ONLY)
INSERT LINK FOR
ITC (Stk Ref 103 14 200)
ITC-DS (Stk Ref 103 14 210)
24HR CHANGE OVER
FAN 1
OUTPUT
LK1
CONTROLLER
CONNECTIONS
REMOTE VISUAL
LED 1
FAIL
FAN 1
FAIL
FAN 2
A
LED 2
K
K
A
FS
FG
SENSOR
S1
CONNECTIONS
SG
EXTRA LOW VOLTAGE
WIRING UP TO 25m LONG.
NOTE: The ITC and ITC-DS controller operate by detecting the current flowing to the fan. If it is necessary to switch
the fan On/Off for any reason; e.g. fan Off at night, this switch operation must be done via the ITC and ITC-DS
controller by making or breaking a contact connected across S1-SG. Otherwise a fan failure will be registered.
4
Fig. 3
ATQ ACOUSTIC SINGLE PHASE FAN AND AN AUTO-TRANSFORMER WIRING DETAILS
STOCK REFERENCE NUMBERS:
ATQ 100-12C, ATQ 125-12C, ATQ 150-12C, ATQ 160-12C, ATQ 200-12C
ATQ 250-12C, ATQ 315-12LC, ATQ 315-14HC, ATQ 400-14C.
L
N
U1
U2
TK
TK
N
L1
L2N1
Fuse
L
~
N
(220-240V).
E
1 Phase Supply
L1
N
EE
L1NL2L3
N L
E
24V AC
E
L2
L3
TK
TK
FAN 2
OUTPUT
240V
INPUT
ABDCE
ITC (Stk Ref 103 14 200)
ITC-DS (Stk Ref 103 14 210)
CONTROLLER
CONNECTIONS
REMOTE VISUAL
LED 1
A
103-14-103
Transformer
1 Phase Auto
103-14-105
Speed Controller.
FAIL
103-14-113
103-14-107
FAN 1
FAN 2
FAIL
TK
L
N
U1
U2
TK
N
L1
(ITC-DS ONLY)
INSERT LINK FOR
24HR CHANGE OVER
LED 2
K
K
A
L2
FS
L3
FAN 1
FG
E
TK
TK
OUTPUT
LK1
SENSOR
CONNECTIONS
S1
SG
EXTRA LOW VOLTAGE
WIRING UP TO 25m LONG.
NOTE: The ITC and ITC-DS controller operate by detecting the current flowing to the fan. If it is necessary to switch
the fan On/Off for any reason; e.g. fan Off at night, this switch operation must be done via the ITC and ITC-DS
controller by making or breaking a contact connected across S1-SG. Otherwise a fan failure will be registered.
5
Fig. 4
ATQ ACOUSTIC SINGLE PHASE (WITHOUT TK CONNECTIONS) FAN WIRING DETAILS
STOCK REFERENCE NUMBER:
ATQ 500-14C.
96 must be fitted and the link
N.B. Links between terminals 1
to 95, 3 to 6, 5 to A2 and 23 to
between terminals 24 to 96 must
A suitable sized
fitted to provide motor
240 Volt D.O.L. Starter
overload relay must be
1 Phase Supply
(220-240V 50Hz)
E
REMOVED.
be
4
2
95
23
A1
E
protection.
L
~
N
E
6
96
24
1
3
5
A2
95
23
A1
E
N
L1
L2
L3
TK
TK
240V
INPUT
FAN 2
OUTPUT
240V
E LNL1NL2L3
INPUT
24V AC
ABDCE
ITC (Stk Ref 103 14 200)
ITC-DS (Stk Ref 103 14 210)
96
24
A2
INSERT LINK FOR
E
6
5
N
(ITC-DS ONLY)
24HR CHANGE OVER
L
N
U1
U2
U2
L1
L
N
U1
REMOVED.
N.B. Links between terminals 1
240 Volt D.O.L. Starter
TK
be
96 must be fitted and the link
to 95, 3 to 6, 5 to A2 and 23 to
between terminals 24 to 96 must
protection.
A suitable sized
fitted to provide motor
overload relay must be
4
2
1
3
L3
L2
TK
FAN 1
OUTPUT
LK1
CONTROLLER
CONNECTIONS
REMOTE VISUAL
LED 1
FAIL
FAN 1
FAIL
FAN 2
LED 2
K
K
A
A
FS
FG
SENSOR
S1
CONNECTIONS
SG
EXTRA LOW VOLTAGE
WIRING UP TO 25m LONG
NOTE: The ITC and ITC-DS controller operate by detecting the current flowing to the fan. If it is necessary to switch
the fan On/Off for any reason; e.g. fan Off at night, this switch operation must be done via the ITC and ITC-DS
controller by making or breaking a contact connected across S1-SG. Otherwise a fan failure will be registered.
6
Fig. 5
ATQ ACOUSTIC SINGLE PHASE FAN (WITHOUT TK CONNECTIONS) AND 5 STEP
AUTO-TRANSFORMER WIRING DETAILS
STOCK REFERENCE NUMBER:
ATQ 500-14C.
(220-240V).
1 Phase Supply
N.B. Links between terminals 1
to 95, 3 to 6, 5 to A2 and 23 to
A suitable sized
240 Volt D.O.L. Starter
overload relay must be
~
NL
E
E
REMOVED.
be
96 must be fitted and the link
between terminals 24 to 96 must
96
95
23
24
A1
A2
E
protection.
fitted to provide motor
2
4
6
1
5
3
95
E
L3
N
L1
L2
L3
TK
L2
TK
E
6
96
23
24
A1
5
A2
N
L
N
U1
U2
U2
L1
L
N
U1
REMOVED.
N.B. Links between terminals 1
240 Volt D.O.L. Starter
TK
be
96 must be fitted and the link
to 95, 3 to 6, 5 to A2 and 23 to
between terminals 24 to 96 must
protection.
A suitable sized
fitted to provide motor
overload relay must be
4
2
1
3
L3
L2
TK
L2
N1
Fuse
N L1
N L N L1
E
FAN 2
OUTPUT
240V
INPUT
FAN 1
OUTPUT
EE
24V AC
LK1
(ITC-DS ONLY)
INSERT LINK FOR
24HR CHANGE OVER
LED 1
LED 2
SENSOR
CONNECTIONS
1 Phase Auto
ITC (Stk Ref 103 14 200)
CD B A
CONTROLLER
REMOTE VISUAL
FAN 1
CONNECTIONS
FAIL
E
Transformer
103 14 103
103 14 105
103 14 107
103 14 113
ITC-DS (Stk Ref 103 14 210)
Speed Controller.
FAN 2
FAIL
A
FS
FG
S1
SG
EXTRA LOW VOLTAGE
WIRING UP TO 25m LONG
K
K
A
NOTE: The ITC and ITC-DS controller operate by detecting the current flowing to the fan. If it is necessary to switch
the fan On/ Off for any reason; e.g. fan Off at night, this switch operation must be done via the ITC and ITC-DS
controller by making or breaking a contact connected across S1-SG. Otherwise a fan failure will be registered.
7
VENT-AXIA SALES CENTRES
ENGLAND & WALES NATIONAL CALL CENTRE
Newton Road, Crawley
West Sussex
RH10 9JA
Telephone: 01293 530202
Fax: 01293 565169
NORTHERN IRELAND
Telephone: 02890 402220
Fax: 01293 565169
SCOTLAND
Telephone: 0141 429 1166
Fax: 01293 565169
REPUBLIC OF IRELAND
Vent-Axia Ventilation Ltd.
921 Western Industrial Estate
Naas Road, Dublin 12.
Telephone: (01) 450 4133
Fax: (01) 450 4570
Did you find these instructions easy to use?
We value your comments, contact us via:
email: info@vent-axia.com
**********************************************************************
The Vent-Axia Guarantee
Applicable only to products installed and used in the United Kingdom. For details of the guarantee outside
the United Kingdom contact your local supplier.
Vent-Axia guarantees its products for two years from the date of purchase against faulty material or
workmanship. In the event of any part being found to be defective, the product will be repaired, or at the
Company's opinion replaced, without charge, provided that the product:
1) has been installed and used in accordance with the instructions given with each unit.
2) has not been connected to an unsuitable electricity supply (The correct electricity supply
voltage is shown on the product rating label attached to the unit).
3) has not been subjected to misuse, neglect or damage.
4) has not been modified or repaired by any person not authorised by the Company.
IF CLAIMING UNDER THE TERMS OF THE GUARANTEE
please return the complete product, carriage paid to your original supplier or nearest Vent-Axia Centre, by
post or in person. Please ensure that it is adequately packed and accompanied by a letter clearly marked
'Guarantee Claim' stating the nature of the fault and providing proof of date and source of purchase.
****************************************
**********************************************************************
As part of the policy of continuous product improvement Vent-Axia reserve the right to alter specifications without notice.
****************************************
Head Office:
Fleming Way, Crawley, West Sussex RH10 9YX
Tel: 01293 526062 Fax: 01293 551188
Internet site at: www.vent-axia.com
458713A 0103
8
Loading...