Venmar C700 Series, CC700 Series, CIC700 Series, CIS700 Series Installation Instructions Manual
09530 Rev. A
GLASS PANEL
INSTALLATION INSTRUCTIONS
APPLIES TO THE FOLLOWING RANGE HOOD SERIES
C700, CC700, CIC700 AND CIS700
Venmar Ventilation Inc., 550 Lemire Blvd.
Drummondville QC J2C 7W9
1-800-567-3855
www.venmar.ca
- 2 -
•IT IS RECOMMENDED TO WEAR SAFETY GLASSES AND GLOVES WHILE PERFORMING THESE INSTRUCTIONS.
•HANDLE GLASS PANEL WITH CARE.
•ALL TEMPERED GLASS CAN EXPERIENCE SPONTANEOUS BREAKAGE. IFBROKEN, TEMPERED GLASS FALLS
OUTOFIT’S OPENING IN INTERLOCKING CLUMPS. TEMPERED GLASS CAN, ON OCCASION, BREAK INTO LARGE
SHARDS RATHER THAN THE CLASSIC TINY PIECE PATTERN.
•RISK OF ELECTRICAL SHOCK. BEFORE REPLACING THE GLASS PANEL, SWITCH POWER OFF AT SERVICE
PANEL AND LOCK SERVICE DISCONNECTING MEANS TO PREVENT POWER FROM BEING SWITCHED ON
ACCIDENTALLY.
WARNING
!
C700 SERIES
IF THE RANGE HOOD IS NOT INSTALLED YET, REFER TO STEP 4 OF THE HOOD INSTALLATION GUIDE.
IF THE RANGE HOOS IS ALREADY INSTALLED FOLLOW THESE STEPS:
To remove filters: Lift filters by pushing
them towards the back and rotate. Set the
filters aside.
Remove the bottom panel 10 retaining
screws and set aside.
NOTE: Both light assemblies will have to
be disconnected in order to
remove the bottom panel (see
step 3).
Slightly pull the bottom panel out.
Press on tabs and pull to disconnect both
light assemblies electrical harenesses
from light connectors.
Slide bottom panel out and set aside.
Remove new glass panel nuts from both studs and set aside.
1
HO0174
HO0181
SCREW
LOCATIONS
HO0176
2
3
4
AFTER A POWER FAILURE OR DURING THE RANGE HOOD POWER UP, A 5-SECOND BOOTING SEQUENCE IS
EXECUTED. WAIT FOR THE CONTROL BACKLIGHTING TO TURN OFF BEFORE USE.
CAUTION
- 3 -
If need be, remove current glass panel
retaining nuts from both studs. Discard
glass panel and nuts.
Insert new glass panel studs in hood front
holes.
While holding glass panel, pre-tighten
previously removed nuts by hand. Ensure
glass panel is flush with top of hood and
centered from side-to-side.
Then, using a 3/8" socket, tighten nuts
completely.
Insert bottom panel in the back of the hood and reconnect each light assembly electrical
harness to its light connector.
Secure bottom panel to the hood, using the 10 previously removed screws.
Reinstall baffle filters.
CIC700 SERIES
IF THE RANGE HOOD IS NOT INSTALLED YET, REFER TO STEP 6 OF THE HOOD INSTALLATION GUIDE.
IF THE RANGE HOOS IS ALREADY INSTALLED FOLLOW THESE STEPS:
To remove filters: Lift filters by pushing
them towards the back (opposite control
side) and rotate. Set the filters aside.
Remove new glass panel nuts from both studs and set aside.
If need be, remove current glass panel
retaining nuts from both studs. Discard
glass panel and nuts.
Insert new glass panel studs in appropriate
hood holes.
NOTE:Install the glass panel with the
control pictogram on the front of
the hood.
While holding glass panel, pre-tighten
previously removed nuts by hand. Ensure
glass panel is centered.
Then, using a 3/8" socket, tighten nuts
completely.
Reinstall baffle filters.
GLASS PANEL STUD
NUT
5
678
HO0195
1
2
HD0438
GLASS
PANEL STUD
NUT
3
4
HD0440
Loading...