Venitem RIALTO L, RIALTO LSX, RIALTO LS, RIALTO X, TRIADE L User & Installation Manual

MA-SE-RTL0-03-01 Manuale Rialto Triade Lido Eng rev1 Page 1 of 8

INSTALLATION MANUAL

SOUNDER MODELS

RIALTO L – LS – X – LSX

TRIADE L – LS – QL – QLS

LIDO L – X – LS – LSX

DESCRIPTION

L models description: self-powered 12 Vdc sounder with high-brightness low-consumption LED flashing unit - double reed

tamper against sounder opening and against any attempts of removing the sounder from the wall – programmable sounds and
timings – alarm counting – optical and acoustic signaling of System ON/OFF (arming/disarming) - electronic circuit protected
against polarity inversion and tropicalized by resin immersion – microprocessor self-check of recharge, battery and speaker –
flash reset input – internal cover made of 10/10 zinc-plated steel (Aluzinc system) – outside cover made of painted ABS or 10/10
zinc-plated steel (Aluzinc system) or shiny stainless steel according to the model chosen.

LS models description: technical features as per L models, with patented double micro anti-foam anti-shock device against hard
hits (patent no. 00238576).

MA-SE-RTL0-03-01 Manuale Rialto Triade Lido Eng rev1 Page 2 of 8

CONNECTION SCHEME

A) CONNECTION USING THREE WIRES.

Connect 13.8 Volt power supply coming from the control panel to the corresponding terminals:

-RIC negative; +RIC positive; +C positive-missing trigger.

NOTE: DIP-SWITCH no. 2 is set by the manufacturer in OFF position, POSITIVE-MISSING TRIGGER.

B) CONNECTION USING TWO WIRES

Connect 13.8 Volt power supply coming from the control panel to the corresponding terminals:

-RIC negative; +RIC positive. (make a jumper between +C and +RIC).

NOTE: DIP-SWITCH no.2 is set by the manufacturer in OFF position, POSITIVE-MISSING TRIGGER

C) BLS TERMINAL, NEGATIVE INPUT FOR SOUND BLOCK

It activates the sound interruption trigger by taking a negative (0V) to terminal no. 4.

D) STI TERMINAL, SYSTEM STATUS NOTICE (PERMANENT/MOMENTARY ALARM SYSTEM ON/OFF)

DIP 3 in OFF position

 Giving a positive to terminal no. 5, all LEDs of the flashing unit flash 3 times (ON). Anomalies are reset to zero.
 Taking away the positive, all LEDs stay lighted up steady for 5 seconds (OFF) and the complete sounder test is launched. In

case of anomalies, they are duly notified.

PONT 1 (R74) – UNTOUCHED (STANDARD SETTING): Momentary ON-OFF signaling and 1 LED keeps on flashing in intermittent mode

until there is positive signal to terminal no. 5.

PONT 1 (R74) – CUT: Momentary ON-OFF signaling

GND 0V

+13.8Vdc and SOUNDER TRIGGER

TAMPER LINE

CONTROL PANEL

GND 0V

+13.8V

OUTDOOR SOUNDER TRIGGER

TAMPER LINE

CONTROL PANEL

MA-SE-RTL0-03-01 Manuale Rialto Triade Lido Eng rev1 Page 3 of 8

DIP 3 in ON position

 Giving a negative (0V) to terminal no. 5, all LEDs of the flashing unit flash 3 times (ON). Anomalies are reset to zero.
 Taking away the negative, all LEDs stay lighted up steady for 5 seconds (OFF) and the complete sounder test is launched.

In case of anomalies, they are duly notified.

Activated sounds: To activate sounds (three BEEPs while arming and a long BEEP while disarming) set DIP 4 in ON position.

E) RES TERMINAL, NEGATIVE INPUT OF FLASHING UNIT RESET

When set (through PONT no. 2), it stops the flashing activity of the flashing unit by taking terminal no. 6 to 0V for one second.

F) OUT ANM TERMINAL AND ANOMALY LED

The sounder is managed by a microcontroller able to check if the battery recharging process is going on properly, if the battery
status is good, if the speaker is good or faulty and if the power amps are in good condition. In case of anomaly, the open­collector terminal OUT ANM opens and LD1 LED on the sounder board shows the fault type by making a certain number of
flashes followed by a short pause.
The microprocessor automatically performs the battery current test every 4 hours. Moreover, it continuously performs other
tests. If the sounder is correctly supplied, the anomaly output (terminal no. 7) usually stays at 0V (max consumption 50mA). If
any of the tests performed fails, the anomaly output disconnects from ground and becomes free.
When the sounder receives power supply for the first time (13V or battery), to make installation easier, anomalies are
automatically reset to zero when their cause disappears. After the first alarm trigger, anomalies are reset to zero only
through +C, RES or a command to STI.
To launch the remote test, take terminal no. 5 (STI) to 12V for 10 seconds, then take away the voltage from the terminal.
These steps launch the test which will last 60 seconds. During the test, the sounder verifies its own functioning and notifies
any anomalies both through the anomaly output (OUT ANM) and the anomaly LED, as indicated in the chart below. To reset

the anomaly to zero, remove its cause first, then wait 10 seconds and take terminal no. 5 (STI) to 12V for at least 10
seconds. When the command is taken away from terminal +C for a very short time lapse, all anomalies are reset to zero
with the exception of those concerning the battery. After 4 hours from battery restore, the sounder performs the tests
once again and updates the anomaly notices, including battery anomaly.

In case any anomaly appears, the flashing unit LEDs flash faster and the acoustic notice at arming becomes a single BEEP.

ANOMALY NOTICE CHART

ANOMALY red LED

ANOMALY OUTPUT (OUT NO. 7)

SPEAKER INTERRUPTION (test performed every 10 s)

1 FLASH

OUTPUT OPEN (OPEN COLLECTOR OFF)

NO RECHARGE CURRENT (recharge current is lower than 11.5V)
(test performed every 10 s)

2 FLASHES

OUTPUT OPEN (OPEN COLLECTOR OFF)

BATTERY IS DISCONNECTED, IS LOWER THAN 2.5 V
(test performed every 4 hours)

3 FLASHES

OUTPUT OPEN (OPEN COLLECTOR OFF)

BATTERY IS INSUFFICIENT, IS LOWER THAN 10 V
(test performed every 4 hours)

4 FLASHES

OUTPUT OPEN (OPEN COLLECTOR OFF)

INTERNAL BATTERY RESISTOR > 3.5 OHM
(test performed every 4 hours)

5 FLASHES

OUTPUT OPEN (OPEN COLLECTOR OFF)

SPEAKER POWER AMPs ARE INTERRUPTED
(test performed every 10 seconds)

6 FLASHES

OUTPUT OPEN (OPEN COLLECTOR OFF)

SOUNDER IS NOT POWERED OR SOUNDER MICROPROCESSOR IS
FAULTY

OFF

OUTPUT OPEN (OPEN COLLECTOR OFF)

NO ANOMALIES

OFF

OUTPUT TO GROUND, 0V
(OPEN COLLECTOR IS ACTIVE)

G) ANTI-OPENING AND ANTI-REMOVAL TAMPER

CONNECTION

Connect TAMPER terminals no. 8 and no. 9 to the
tamper line coming from the control panel.

H) BATTERY CONNECTION

Connect the 12V battery to the corresponding
connector faston.

MA-SE-RTL0-03-01 Manuale Rialto Triade Lido Eng rev1 Page 4 of 8

SETTING

Chart 5: ALARM SYSTEM ON/OFF NOTICE, TERMINAL no. 5

DIP 3

NOTICE (sound)

OFF (default setting)

STI is open = alarm system is disarmed (OFF), STI 12V = alarm system is armed (ON).
Flashes as per PONT 1

ON

STI is open = alarm system is disarmed (OFF), STI 0V = alarm system is armed (ON). Flashes as per PONT 1

Chart 2: ALARM TIMING

DIP 1

Alarm timing

OFF (default setting)

3 minutes

ON

8 minutes

Chart 4: ALARM INPUT POLARITY OF SOUNDER COMMAND, TERMINAL no. 3

DIP 2

Terminal 3

OFF (default setting)

Positive-missing (alarm if disconnected or 0V)

ON

Negative-missing (alarm if disconnected or +12V)

Chart 6: TONE SELECTION

DIP 4

TONE

FREQUENCY LIMITS (Hz)

OFF (default setting)
CERTIFIED

Increasing-Continuous-Decreasing­Continuous

1.400 ÷ 1.800
ON

Increasing-Decreasing (NFC 48-265)

1.400 ÷ 1.600

SOUND IS ACTIVATED ON STI TERMINAL (3 BEEPs while arming and a long BEEP while disarming)

Chart 9: DAILY ALARMS COUNTING

PONT 3 (R85)

ALARMS NUMBER DURING THE 24 HOURS AFTER THE FIRST ALARM

CONNECTED (default setting)

Infinite alarms

CUT

MAX 4 DAILY ALARMS (each alarm is counted only if it lasts at least 30 seconds)
IN CASE MORE THAN 4 DAILY ALARMS OCCUR, THE SOUNDER FLASHES WITH NO SOUND
(STI resets alarm counting)

Terminal 5

Anomaly output.
Open-collector at 0V = no anomaly

MA-SE-RTL0-03-01 Manuale Rialto Triade Lido Eng rev1 Page 5 of 8

INSTALLATION/MAINTENANCE ADVICES:

In case the sounder does not work properly, verify if the LED located on the main board is flashing.
If it flashes, check the ANOMALY NOTICE CHART above.

MOUNTING:

1. Screw the sounder on the wall and check if the tamper works properly;

2. Insert the connection cables through the holes localed on the sounder base;

3. If necessary, modify the default settings acting on the DIPSWITCHES as indicated in the charts here above;

4. Connect the battery and the power supply to the control panel;

5. Close both internal and external covers using the screws provided;

6. Battery must have UL94-HB flammability rate;

7. Power supply must be of SELV type.

Attention: not to have condensation in the sounder, it is important to avoid any air flow inside the duct. To such purpose, once the
sounder is connected, seal the hole using some silicon or any other plaster. This operation prevents condensation from forming inside the
sounder; condensation mostly appears in winter and it is usually caused by warm and humid air coming out of the wall where the sounder
is installed and passing through the holes located on the sounder base.

117.1 dB (Rialto LSX)

115.0 dB (Triade L/Lido LS)

115.5 dB (Rialto LS)

Diagram 1

MA-SE-RTL0-03-01 Manuale Rialto Triade Lido Eng rev1 Page 6 of 8

TECHNICAL FEATURES

WARRANTY:

All Venitem products are granted against factory or material defects. In order to improve design and quality of the products,
Venitem reserves the right to modify the products without prior notice. All faulty or defective products must be returned to the
supplier.

Voltage

Nominal power supply voltage

13.8 Vdc

Minimum – maximum command limits

4 Vdc – 5.4 Vdc; 10.8Vdc – 11.9Vdc;

0.51Vdc – 1.55Vdc

Minimum power supply

10.5 Vdc

Maximum power supply

15.5 Vdc

Current

Sound consumption from battery

1.3 A +100/-300 mA

Maximum continuous recharge

700 mA  100 mA

Flashing unit consumption

80 mA  10 mA

Consumption in stand-by

15mA

Consumption from control inputs

+0.5 mA @Vc=12V; -0,3 mA @Vc=0V

Open collector

-10mA max

LED flashing unit life

1,000,000 flashes

Timing

3 minutes, settable at 8 minutes

Battery capacity

12V 2.0 Ah

Switch tamper range

N.C.

0.2 A max.

Fundamental frequency

All models (DIP 4 in OFF position, CERTIFIED TONE)

1435 Hz

Sound pressure dB (@) at 1 m

All models

SEE DIAGRAM

Mechanics

External cover

TRIADE L – TRIADE LS – TRIADE QL – TRIADE QLS

Painted ABS

RIALTO L – RIALTO LS
LIDO L – LIDO LS

Painted steel

RIALTO X – RIALTO LSX
LIDO X - LIDO LSX

Stainless steel
Internal cover

Zinc-plated steel

Flashing unit lens

Polycarbonate

Protection degree

IP 44

Environmental class

IV (outdoor)

Operating Temperature

From -25°C to +55°C

Size
RIALTO

206 x 206 x 97 mm (H x L x P)

TRIADE

245 x 250 x 97 mm (H x L x P)

LIDO

252 X 206 X 110 mm (H x L x P)

Weight
RIALTO

2,564 g

TRIADE

2,082 g

LIDO

2,951 g

Standards compliance

Certifying body
(IMQ-SISTEMI DI SICUREZZA)

EN50131-4:2019
Security degree

L, LS and LSX models

Degree 3

MA-SE-RTL0-03-01 Manuale Rialto Triade Lido Eng rev1 Page 7 of 8

NOTE

MA-SE-RTL0-03-01 Manuale Rialto Triade Lido Eng rev1 Page 8 of 8

Via del Lavoro, 10 - 30030 Salzano (VE) Tel. [phone] – Fax [phone] Web site www.venitem.com E-mail [e-mail]