Venitem DOGE EV12, DOGE EV24, DOGE EV230 Installation Manual

Power supply, voltage, current

EV12V

From 10V to 15Vdc – Maximum current from +RC
700mA

EV24V

From 20V to 30Vdc – Maximum current from +RC
400mA

EV220V

230Vac +/- 10%

Current MAX speaker from
battery

1,4A (programmable – see chart)
Flashing light current

80 mA  10 mA

Fundamental frequency

See chart

Max decibel

106 dB @ 3m

LED flashing light duration

1.000.000 flashes

Water/dust protection level

IP 44

Environmental class

IV (outdoor)

Operating temperature

from –25°C to +55° C

Alarm duration

Programmable (see chart)

Activation trigger

See chart

Battery

12V 2Ah (for all models of Doge EV)

Size 330x210x115 (H x W x D)

Weight

1.980 gr

EVACUATION SOUNDER

DOGE EV12 – EV24 – EV230

INSTALLATION MANUAL

DESCRIPTION

3 input outdoor sounder with 10 sounds for evacuation alarms. Two sound power regulations.

Possibility to choose the trigger type among positive or negative missing or giving.
Connection for sound synchronism among all the sounders.
LED flashing light for anomalies signalization, for example: power supply shortage, battery fault, speaker not working.
The current consumed by the control panel or by the power supply is limited to 700mA for EV12 model and 400mA
for EV24 model.
Timed alarm sound duration.

TECHNICAL FEATURES

MA-SE-EVA1-01-00 Manuale Doge Evacuazione eng rev0 Page 1 of 4

Chart 1

Terminals

Connections

+ S1/RC (1)

12V battery recharge (EV12 and EV230)
or 24V (EV24)

- S1/RC (2)

Battery recharge 0V

+S2 (3)

Relay anomaly 100mA/ 48V MAX

R (4)

Relay anomaly 100mA/ 48V MAX

-S2 R (5)

Evacuation command 1 input

+ S3 (6)

+12V positive output used to trigger the
inputs

- S3 (7)

Evacuation command 2 input

(8)

Syncronism

(9)

Evacuation command 3 input

Terminals on TL1207

0 - 230

Power supply for Doge EV230

Table 2 DIP SWITCH

DIP

Function

DIP1

Alarm timing

DIP2

Alarm timing

DIP3

System status

DIP4

Consumed power and current

DIP5

Sounds group selection

DIP6

Sounds group selection

DIP7

Trigger polarity, positive or negative

DIP8

Transition giving or missing trigger

ON

OFF

J1 Battery and

speaker

Connection

J2 LED

Connection

NEGATIVE GIVING TRIGGER 3
SOUND CONNECTION

Connect the 12Vcc or 24Vcc power supply to the
recharging terminals S1/RC (Recharge) 1 and 2.
Connect inputs 5,7,9 with DIP7 = ON and DIP8 =
ON, as shown in the picture below

NEGATIVE GIVING TRIGGER AND
POLARITY INVERSION 3 SOUNDS
CONNECTION

Connect the 12Vcc or 24Vcc power supply to the
recharging terminals S1/RC (Recharge) 1 and 2.
Connect the end line resistance coming from the fire
control panel to the terminals 4 and 5. Connect in
polarity inversion the inputs 3, 5 to the fire control
panel. Connect 7 and 9 as shown in the picture below.
DIP7 = ON and DIP 8 = ON

CONNECTION SCHEME

ATTENTION: IN CASE THE SOUNDER IS SET WITH MISSING TRIGGER AND ONE OR MORE OF THE
THREE INPUTS ARE NOT USED, CONNECT THE INPUTS THAT ARE NOT USED TO THE
NEGATIVE/POSITIVE, FOLLOWING DIP 7

TERMINALS and DIP-SWITCH SETTING

MA-SE-EVA1-01-00 Manuale Doge Evacuazione eng rev0 Page 2 of 4