BBlluueettooootthh PPrreesseenntteerr
VVPP--11000000
BBuuttttoonn FFuunnccttiioonn ::
20F-1, No.77, Sec.1 , Hsin Tai Wu Rd., Hsi-Chih, Taipei Taiwan R.O.C.
Tel. No.:+886-2-2698-3608 Fax No.:+886-2-2698-3648
1/3
Dec.19”2007 V1.0
BBlluueettooootthh PPrreesseenntteerr
VVPP--11000000
QQuuiicckk SSttaarrtt
1. Power On/Off
Press Blank and Start key together, and then Blue LED will flash. Now, VP-1000 is
powered On.
Press Blank and Start key together again, then VP-1000 will be powered Off.
2. Pairing
Press Start and Page Up key together, and then Blue and Red LED flash alternative.
Now, VP-1000 is under pairing mode.
Step 1. Set VP-1000 under pairing mode
Step 2. Follow the pairing process of PC to search & pair with VP-1000
Step 3. After pairing is complete, VP-1000 will connect automatically. When VP-1000 is
connected, Blue LED will light on.
3. Connect
VP-1000 will auto connect to the paired device when powering on.
You also can press any key to connect to the paired device when Bluetooth link is
disconnect.
4. Auto Disconnect/Power Off
VP-1000 will auto disconnect with PC, if no any key be pressed for 20 minutes.
VP-1000 will auto powering off, if VP-1000 is under disconnect state for 20 minutes.
5. Laser Pointer
In view of safety consideration, laser pointer initially is Off when VP-1000 is power on.
To press Blank key and hold for 2 seconds, then laser point er will be enable. To press
Blank key and hold for 2 seconds again, then laser pointer will be disable.
When laser pointer is under disable state, the Blue LED will quick flash as you press
laser pointer key.
20F-1, No.77, Sec.1 , Hsin Tai Wu Rd., Hsi-Chih, Taipei Taiwan R.O.C.
Tel. No.:+886-2-2698-3608 Fax No.:+886-2-2698-3648
2/3
Dec.19”2007 V1.0
BBlluueettooootthh PPrreesseenntteerr
VVPP--11000000
6. Low Battery
The LED indicator will change from Blue to Red, when battery is low.
Please plug-in charging cable/adapter to charge battery, when Red LED flash.
7. Charge Battery
The Green LED will light on, when plug-in charging cable/adapter an d battery in under
charging.
The Green LED will off, when battery is charged complete.
20F-1, No.77, Sec.1 , Hsin Tai Wu Rd., Hsi-Chih, Taipei Taiwan R.O.C.
Tel. No.:+886-2-2698-3608 Fax No.:+886-2-2698-3648
3/3
Dec.19”2007 V1.0
FCC ID: VHVBTVP1000
FCC Compliance and Advisory Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:(1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
according to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential inst allatio n. This equipment generates,
uses and can radiate radio frequency energy and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try correct the interference b y one or more
of the following measures:
1.Reorient the receiving antenna.
2.Increase the separation between the equipment and receiver.
3.Connect the equipment into and outlet on a circuit different from that to which the receiver is
connected.
4.Consult the dealer or an experienced radio/TV technician for help.
Any special accessories needed for compliance must be specified in the instruction manual.
Warning: A shielded-type power cord is required in order to meet FCC emission limits and
also to prevent interference to the nearby radio and television reception. It is essential that
only the supplied power cord be used. Use only shielded cables to connect I/O devices to this
equipment.
CAUSION: Any changes or modifications not expressly approved by the party re sponsible for
compliance could void your authority to operate the equipment.
Loading...