Vencer BTVK1000 User Manual

VVKK--11000000 AAPPPP QQuuiicckk GGuuiiddee

Getting Started

z Turning the VK-1000 On or Off

To turn the VK-1000 on

Long press button 3 seconds will turn on the VK-1000. Once VK-1000
be turned on Green LED will flash twice.

To turn the VK-1000 off

When VK-1000 on active mode, long press button 3 seconds will turn
off the VK-1000. Once VK-1000 be turned off Red LED will flash four
times.

z Pairing.

Long press button 6 seconds will turn on the VK-1000 and enter pairing
mode. Once VK-1000 enter pairing mode the Red and Green LED will
flash interlaced.

z Low Battery.

Once low battery, Red LED will flash twice each minute.

20F-1, No.77, Sec.1 , Hsin Tai Wu Rd., Hsi-Chih, Taipei Taiwan R.O.C.

Tel. No.:[phone] Fax No.:[phone]

1/10

VVKK--11000000 AAPPPP QQuuiicckk GGuuiiddee

z Working with iPhone 4S

 Make sure the Bluetooth radio has been enabled of iPhone4S.

Press Setting

Select General

20F-1, No.77, Sec.1 , Hsin Tai Wu Rd., Hsi-Chih, Taipei Taiwan R.O.C.

Tel. No.:[phone] Fax No.:[phone]

2/10

VVKK--11000000 AAPPPP QQuuiicckk GGuuiiddee

Turn on the Bluetooth setting.

 Back to the main screen and run Vencer BLE Phone Finder APP.

20F-1, No.77, Sec.1 , Hsin Tai Wu Rd., Hsi-Chih, Taipei Taiwan R.O.C.

Tel. No.:[phone] Fax No.:[phone]

3/10

VVKK--11000000 AAPPPP QQuuiicckk GGuuiiddee

 Long Press VK-1000 Button for 6 seconds to enter the pairing mode for

VK-1000. Red/Green LED will flash alternative.

 Press search button to search the BLE device.

 APP start to searching.

20F-1, No.77, Sec.1 , Hsin Tai Wu Rd., Hsi-Chih, Taipei Taiwan R.O.C.

Tel. No.:[phone] Fax No.:[phone]

4/10

VVKK--11000000 AAPPPP QQuuiicckk GGuuiiddee

 Found VK-1000 BLE device.

 Click VK-1000 to establish the connection.

20F-1, No.77, Sec.1 , Hsin Tai Wu Rd., Hsi-Chih, Taipei Taiwan R.O.C.

Tel. No.:[phone] Fax No.:[phone]

5/10

VVKK--11000000 AAPPPP QQuuiicckk GGuuiiddee

 VK-1000 connected with iPhone4S and go to setting page.

 Press back button to back to previous page.

20F-1, No.77, Sec.1 , Hsin Tai Wu Rd., Hsi-Chih, Taipei Taiwan R.O.C.

Tel. No.:[phone] Fax No.:[phone]

6/10

VVKK--11000000 AAPPPP QQuuiicckk GGuuiiddee

 Press search button again to search 2nd device.

 Click second VK-1000 to establish the connection

20F-1, No.77, Sec.1 , Hsin Tai Wu Rd., Hsi-Chih, Taipei Taiwan R.O.C.

Tel. No.:[phone] Fax No.:[phone]

7/10

VVKK--11000000 AAPPPP QQuuiicckk GGuuiiddee

 Both two VK-1000 devices connected with iPhone4S.

 Alert setting.

20F-1, No.77, Sec.1 , Hsin Tai Wu Rd., Hsi-Chih, Taipei Taiwan R.O.C.

Tel. No.:[phone] Fax No.:[phone]

8/10

VVKK--11000000 AAPPPP QQuuiicckk GGuuiiddee

z Battery indicator: Indicator the power status.
z Device signal strength: The right side signal higher than left side.
z User setting for alert signal: (-70) means the signal strength less

than -70 the alert will be enable.

z Alert level setting: Setting the alert method that user preferred.

 High: Continuously beep 100 times.
 Middle: Continuously Red LED flash 100 times.
 No any alert.

z Once the link loss (VK-1000 disconnect with iPhone4S), also will

follow this setting to alert user.

 Find me.

z Fine tag: User can press this tag to find tag. Tag will alert once user

press this button.

z Find phone alert setting. Once user presses the button on VK-1000

when connected can make iPhone vibration or play a sound 9 second
based on that user selected.

 If VK-1000 disconnected with iPhone4S by link loss or power off. Once

the VK-1000 enters the distance of connection or power on, the APP will
automatically connect with VK-1000.

20F-1, No.77, Sec.1 , Hsin Tai Wu Rd., Hsi-Chih, Taipei Taiwan R.O.C.

Tel. No.:[phone] Fax No.:[phone]

9/10

VVKK--11000000 AAPPPP QQuuiicckk GGuuiiddee

This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

Part 15B compliance statements for digital devices:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equi pme nt and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

20F-1, No.77, Sec.1 , Hsin Tai Wu Rd., Hsi-Chih, Taipei Taiwan R.O.C.

Tel. No.:[phone] Fax No.:[phone]

10/10