Velopex Intra-X, Intra-XE User Manual
Intra - X
Intra - XE
Automatic X-Ray Film Processor
USER GUIDE
Operation and
Maintenance manual
WARNING:
Do not plug into the electrical mains power supply before
reading this manual – or before filling the machine with
liquids
Register your machine by returning the Warranty Card
to enable full customer support.
Machine serial number to be
quoted on all correspondence:
Introduction
Thank you for purchasing your automatic film processor from
Velopex, we certainly appreciate your business.
In order to maintain the quality of our product and your
processing it is important that you pay close attention to the
following instructions contained in this user’s manual. This will
ensure a long life for your processor.
This manual is to be used with the following Velopex processors:
Intra-X, Intra-XE.
Warranty may be voided if the processor is incorrectly installed
or maintained outside the guidelines set forth in this manual.
Caution: Use assistance when unpacking and
positioning the machine.
VELOPEX INTRA-X
User Guide
ii
Contacts
EUROPE
MEDIVANCE INSTRUMENTS LTD.
Barretts Green Road . Harlesden
London . NW10 7AP . UK
Tel.: +44 (0)20 8965 2913
Fax: +44 (0)20 8963 1270
www.velopex.com
USA
VELOPEX INTERNATIONAL INC.
105 East 17th Street . St. Cloud
Florida . 34769 . USA
Tel.: 888 - 835 - 6739
Fax: (407) 957 - 3927
www.velopexusa.com
iii
Velopex Processor - Exterior
6
3
2
4
5
7
9
1
1 Velopex X-Ray Film Processor - Left Side
Film Collector
2
Endo Slide
3
On/Off Power Switch
4
‘Run’ Button
5
10
Viewer Cover
6
Daylight Loader viewing Window
7
Hand entry port/Glove
8
Daylight Loader - Left Side
9
Film Entry Guide
10
8
Machine Accessories and Extras Supplied
12
13
14
15
16
Transport Module
11
17
8
11
18
12 Silicone Grease
13 Film Collecting Tray
14 Cleaning Brush
15 Turning Tool
16 UK - Electricity Supply Cord
17 USA - Electricity Supply Cord
18 Continental - Electricity Supply Cord
Table of Symbols
Symbol Description
Alternating Current
Off (Power: Disconnect from the mains)
On (Power: Connect to the mains)
Type ‘b’ equipment
VELOPEX INTRA-X
User Guide
iv
‘RUN’ Button / Process switch
Protective Earth (Ground)
Symbols used within Manual
Tip
Attention / Warning
Contents
Specification ................................................................. 2
Installation* .................................................................. 3
Pre Installation Instructions .............................................. 3
Daylight Loader Installation (when required) ............... 5
Filling with Chemicals ........................................................ 8
Operation ...................................................................... 11
Maintenance .................................................................. 15
Trouble Shooting .......................................................... 19
1
INSTALLATIONOPERATIONTROUBLE SHOOTING MAINTENANCE
Service Log .................................................................... 24
© June 2005 Medivance Instruments Limited
All rights reserved.
Issue 6 OM13 I/LIT3601M
Specification
(W)
Width (W) 290mm / 11½”
(H)
(D)
VELOPEX INTRA-X
User Guide
2
Depth (D)
Inc. Loader
Height (H) 315mm / 12½”
Weight:
Empty
Full Tanks
Tank Capacity 1.4litres / 2½Imp Pints each
Standard Supply
Voltage
Warm-up time 10 min. approx.
Film Feed Speed 470mm / 18½” per min.
Max film width 65mm / 2½”
Processing time:
Dry
Wet-Endodontic
435mm / 17”
635mm / 25”
12.1Kg / 26½lb
13.9Kg / 30½lb
220-240v 50Hz
110-120v 60Hz
4 min. approx.
2 min. approx.
Pre Installation Instructions
VELOPEX INTRA-X
User Guide
3
INSTALLATION
• Unpacking the VELOPEX
NOTE: For unpacking and lifting the machine into position it is important to have
assistance.
The machine comes in a single carton containing:
Machine, Operator’s Manual, Silicone Grease, Electrical Cord, Transport Module
Turning Tool, Cleaning Brush, Chemical Change Chart and a box of Cleaning Tablets
(UK only), and Daylight Loader (as required).
1. Familiarise yourself with the layout of the machine by referring to the images
as you progress through the manual.
2. Lift the machine from the carton and position on counter top. Remove outer
and inner packaging. The transport modules are protected by internal
packing pieces: these must be discarded.
VELOPEX INTRA-X
User Guide
Pre Installation Instructions (cont.)
• Siting of the VELOPEX
When using the machine in daylight or a darkroom, avoid sources of intense light.
Do not mount the unit under a window, fluorescent light or flood lamp.
4
IMPORTANT NOTE: A well ventilated position is mandatory.
The ambient temperature must be below 80oF (27oC).
Prevent siting the machine above or near other electrical or mechanical equipment.
Surfaces susceptible to water or chemical damage should be avoided, such as
carpeted areas.
1. COUNTER
a. Use a stable and level counter that will support a weight of at least
100 lbs. (50 Kg.).
b. When the machine is filled with chemicals, make sure the stand does not
rock or shake. NEVER move the machine with chemicals in the tanks.
2. ELECTRICAL SUPPLY
a. 115Vac 60Hz, 10A, 1150W (USA)/230Vac 50Hz, 10A, 1150W (World Wide).
b. The power source must be within three (3) feet (1m) of the machine. It
should be easily accessible for operation and maintenance.
WARNING: X-ray radiation can be harmful to patient, technician and dentist.
Inadequate lead shielding of the darkroom or film storage area will also cause
fogging from exposure of films to stray x-ray radiation. Consult your local
codes, Health Department or Dental Equipment Dealer for proper construction
of darkroom or placement of film processing equipment in the vicinity of x-ray
radiation sources.
INSTALLATION
Daylight Loader Installation (as required)
Bring the Lid to the upright
position.
1.
TIP: The Lid can be kept in the upright
position while the machine is open, or
lifted away.
Remove Side Panel by Sliding it
Upwards in its Runners.
2.
VELOPEX INTRA-X
User Guide
5
INSTALLATION
3a.
Remove All Packing / Wrapping
Material and Modules.
TIP: Start with the Dryer Module, then
the Water Module followed by the Fixer
and Developer Modules. Those should be
removed by sliding the Tanks out.
Loading...