How it Works
Velodyne
Loading...
VA-907.2
User Manual
6 pgs104.52 Kb0

Velodyne VA-907.2 User Manual

Download
Page 1
"It delivered room-shaking bass and dramatically demonstrated the effectiveness of a single subwoofer placed to one side of the room"
- Julian Hirsh Stereo Review, January 1997
"If you want the absolute-deepest, most feel it-in-your-tushy BASS under a grand, look no farther than the Velodyne . . ."
- Corey Greenberg
Home Theater, February 1995
Velodyne Acoustics, Inc.
1070 Commercial St. Suite #101
San Jose, CA 95112
907.2
Owner's Manual
408.436.7270 voice
408.436.7276 fax
Web Site: http//www.velodyne.com
E-mail: velodyne@earthlink.net
Printed on recycled paper.
Audio/Video Subwoofer System
Page 2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Caution
To reduce the risk of electric shock, do not remove back panel. No user-serviceable parts inside. Refer servicing to qualified service personnel.
The lighting flash with arrowhead symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the subwoofer.
1. Read Instructions -- All safety and operating instructions should be read before the subwoofer is operated.
2. Retain Instructions -- The safety and operating instructions should be retained for future reference.
3. Heed Warnings -- All warnings on the subwoofer and in the operating instructions should be adhered to.
4. Follow Instructions -- All operating and use instructions should be followed.
5. Water and Moisture -- The subwoofer should not be used near water -- for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, near a swimming pool or the like.
6. Wall or Ceiling Mounting -- The subwoofer should be mounted to a wall or ceiling only as recommended by the manufacturer.
7. Ventilation -- The subwoofer should be situated so that its location or position does not interfere with its proper ventilation. For example, the subwoofer should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or placed in a built-in installation such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.
8. Heat -- The subwoofer should be situated away from heat sources such as radiators, heat registers, stoves, or other subwoofers that produce heat.
9. Power Sources -- The subwoofer should be connected to a power supply only of the type described in the operating instructions or as marked on the subwoofer.
10. Power-Cord Protection -- Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point at which they exit from the subwoofer.
11. "Caution: To prevent electrical shock, match wide blade of plug to wide slot, fully inserted." "Attention: Pour eviter les chocs electriques, introduire lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu' au fond".
12. Cleaning -- The subwoofer should be cleaned only as recommended by the manufacturer.
13. Nonuse Periods -- The power cord of the subwoofer should be unplugged from the outlet when left unused for a long period of time.
14. Object and Liquid Entry -- Care should be taken so that objects do not fall and liquids are not spilled onto the enclosure.
15. Damage Requiring Service -- The subwoofer should be serviced by qualified service personnel when: a. The power-supply cord or plug has been damaged. b. Objects have fallen or liquid has been spilled into the subwoofer. c. The subwoofer has been exposed to rain. d. The subwoofer does not appear to operate normally or exhibits a marked change in performance. e. The subwoofer has been dropped or damaged.
16. Servicing -- The user should not attempt to service the subwoofer beyond what is described in the operating instructions.
All other servicing should be referred to qualified service personnel.
SPECIFICATIONS VA-907.2
Cabinet - including legs 14.5"x14.5"x14.5" (H,W,D)
Frequency Response 35 -120 Hz, +/- 3 dB
High Pass Crossover Passive 85 Hz, 6dB/octave slope
Low Pass Crossover 40 - 120 Hz, active-adjustable
Amplifier 100 watts, 250 watts peak, Class A/B
Woofer 8" forward firing
Passive Radiator 10" downward firing
Magnet 55 oz.
Voice Coil 2" diameter
Inputs/Outputs Line and speaker level
Warranty Two years (parts & labor)
Weight 45 lbs. (approx.)
Specifications are subject to change without notice.
FOR YOUR RECORDS. . . DATE PURCHASED __________________________________ DEALER ______________________________________________ SERIAL # _____________________________________________
*NOTE: Please complete and return your warranty card within ten (10) days.
1 10
☞
Page 3
continuously without any problems. The unit is equipped with a signal sensing turn on/off that will automatically turn on the unit when a signal is present at the inputs and turn off the unit after several minutes when there is no longer any signal at the inputs.
Congratulations!
If you plan to leave the VA-907.2 unused for an extended period of time, we recommend that you turn off the unit by the master power switch on the rear panel.
Troubleshooting & Service
Before seeking service for your VA-907.2 subwoofer, please re­check all systems. Following is a simple troubleshooting guide to assist you.
1. Verify unit is plugged in and power outlet used is active.
2. Is power switch on?
3. Is auto turn on/off set properly?
4. Is unit receiving an input signal from your source?
5. Have all controls on subwoofer (volume, crossover, phase,
etc.) been properly set?
6. If unit has been running at high levels, one of the protection
circuits may be engaged.
Has the built-in amplifier overheated? Has the speaker's voice coil started to heat up?
If the protection circuitry is active, the unit may cycle on and off until operating parameters return to normal. Under more serious condi­tions, the unit may shut off completely. Normal operation will return upon cooling, but you may be required to turn the power off and then on again to reset the unit.
The following conditions require service by a qualified technician:
1. The power cord has become damaged.
2. The unit does not appear to operate normally or exhibits a
marked change in performance.
3. The unit has been exposed to water.
4. Some part of the cabinet or circuitry is physically damaged.
Thank you for purchasing a Velodyne!
9
☞
Congratulations on your purchase of a Velodyne VA-907.2 sub­woofer system. This system represents the state of the art in accurate low frequency reproduction. Read and follow the instruc­tions below to insure safe and proper system operation.
Warning!
To prevent fire or shock hazard, do not expose this equipment to rain or moisture. To avoid electrical shock, do not open speaker enclosure or amp chassis cover. Please observe all warnings on the equipment itself. There are no user serviceable parts inside. Please refer all service questions to your authorized Velodyne dealer.
Prior to installation
Please unpack the system carefully. Remove all staples used to seal the carton as they can scratch the cabinet. Please save the carton and all packaging materials for future use. Record the serial number in the space provided on the warranty card for future reference.
Product Features & Controls
● Built-in 100 watt (RMS) power amplifier
● Subwoofer Direct - switchable crossover bypass
● Adjustable (40 to 120 Hz) low-pass crossover
● Passive (85 Hz fixed) high-pass crossover
● Line-level inputs & outputs
● Speaker-level inputs & outputs
● Signal sensing auto turn on/off with bypass option
● Variable volume control
● Selectable phase control (0 or 180 degrees)
● Anti-clipping circuitry
● Magnetically shielded for video use
● Dual staggered low-pass crossover; 12dB/octave initial,
24dB/octave ultimate
● Gain compression circuit to protect woofer from over excursion
● Input overload protection
2
continued. . .
☞
Page 4
Installation
Your new VA-907.2 subwoofer system provides for a number of installation options. Read all the installation information below in order to determine which installation option is best for your system.
Remember to perform all installation procedures with system power turned off.
Inputs
Your new VA-907.2 subwoofer is equipped with both speaker-level and line-level inputs. Use the LINE-IN jacks when connecting your subwoofer to a pre-amp, signal processor, or line-level crossover. The FROM AMPLIFIER jacks connect directly to the speaker outputs of a integrated amplifier or receiver. Your amplifier section will notice no additional loading effects when you use these inputs because of their high impedance.
Note
Do not use both LINE-IN and FROM AMPLIFIER inputs simulta­neously.
Caution!
Polarity is critical when using speaker level inputs. Reversing the polarity of speaker level inputs can damage the unit.
Volume control
This control allows you to balance the output from the subwoofer to the main speakers in your system. This control should be set to achieve similar volume level from both the main speakers and subwoofer.
Low-pass crossover
Both sets of inputs sum the left and right channels together and the resulting signal is passed through an adjustable low-pass crossover before being amplified. The crossover control allows you to adjust the upper limit of the subwoofer's frequency response from 40 to 120 Hz. The subwoofer's response will begin rolling off above the frequency you set this control to.
enced by placement, depending on the acoustic properties of the listening room. Typically, the optimum location for a subwoofer is tucked away in a corner of your listening room. This location will usually offer the greatest output levels and optimum low frequency extension. The worst location for a subwoofer is typically far away from any walls, and close to the center of your room. Avoid these locations when possible. When using a pair of Velodyne subwoof­ers in stereo, it is preferable to place each subwoofer by the satellite of the same channel.
CAUTION!
The VA series subwoofers have amplifiers built into the cabinet. Do not place the cabinet next to sources of heat such as furnace registers, radiators, etc. The power cord should be routed in such a way that it will not be walked on, pinched, or compressed in any way.
Regardless of where you install your VA-907.2 subwoofer, it must remain in an upright position (passive radiator facing downward). Using, shipping, or otherwise storing the VA-907.2 subwoofer in any other position for an extended period of time may result in damage to the unit not covered by warranty.
Care of your subwoofer
Do not use any harsh detergents or chemicals to clean the cabinet. Abrasives, detergents, or cleaning solutions may damage the finish on the cabinet. We recommend using a damp cloth to clean the cabinet.
During normal conditions, the VA-907.2 subwoofer may be left on
continued. . .
3
☞
8
☞
Page 5
Figure 2: Installation using speaker-level (from amplifier) inputs
LEFT
RIGHT
POWER
MADE IN USA
CAUTION!CAUTION!CAUTION!CAUTION!
CAUTION!
~
Serial # Label
VOLUME
FROM AMPLIFIER
RIGHT
CROSSOVER
LEFT
LOW-PASS
TO SPEAKERS
RIGHT LEFT
IN OUT
You should set the crossover frequency to obtain a smooth and seamless transition from the subwoofer to the main speakers in your system. If your main speakers are smaller units with limited low frequency output, you may wish to choose a higher frequency (such as 100-120 Hz) than you would with larger speakers which have greater low frequency output. With larger speakers, you might start with this control set lower, such as 80 Hz.
A bypass switch is also provided if you wish to use an external crossover. If you are not using an external crossover, we recom­mend that you use the one provided within the unit for optimum performance.
MAIN OUTPUTS (speaker-level)
INTEGRATED AMP / RECEIVER
SATELLITE SPEAKERS
Interconnect cables
When installing your VA-907.2 using the line-level inputs/outputs, you should use standard shielded phono cables. Always keep the lines as short as practical to minimize noise.
When using the speaker-level inputs/outputs, use the same quality speaker cable to your subwoofer as you run to your satellites.
Placement
7
☞
Phase adjustment
This control allows you the ability to compensate for having the subwoofer in a different location than the main speakers. Ideally, you will have the sound from the subwoofer reach the listening position the same time as the sound from the main speakers. However, if the distance from the listening position to the subwoofer and the distance from listening position to the main speakers differs, the sound from each will reach your ears at a different time.
This control allows the signal to be delayed 180 degrees so the output of the subwoofer will blend in to that of your main speakers without any cancellation.
Auto turn on switch
The auto turn on switch allows the user to bypass the auto turn on function if desired. When set in the "auto" mode with main power on, the VA-907.2 will turn itself on when an input signal is present. If no signal is present, after several minutes the unit will shut itself off. When set in the "on" mode, the auto turn on/off function is bypassed and the unit will be on whenever the main power switch is on.
Power switch
The master power switch is located on the right half of the unit. This rocker style switch is the main on/off for the unit. This switch should be set to position 1 for on (up), 0 for off (down).
continued. . .
4
☞
Page 6
Line-level connection
mance you should bypass the internal crossover in your Velodyne subwoofer, the Subwoofer Direct feature.
Figure 1 shows connection to a pre-amplifier's main outputs and returning them to your amplifier inputs.
When installed in this fashion, your satellite speakers will be crossed over at 85Hz which removes the lower bass from your amplifier and speakers, enabling them to do a better job reproduc­ing high frequencies. By utilizing this method, you will have a bi­amplified system, gaining improved power and headroom for your system.
A word about subwoofer outputs
The Velodyne subwoofer is designed to operate using the full range audio signal for input when using the built-in crossover. Some surround sound processors/receivers, including the Dolby AC3 system with their .1 channel output, have a "subwoofer out" jack that
Figure 1: Installation using line-level (line in) inputs
VOLUME
FROM AMPLIFIER
RIGHT
PRE-AMP
MAIN OUTPUTS
RIGHT LEFT
CROSSOVER
LEFT
LOW-PASS
TO SPEAKERS
RIGHT LEFT
IN OUT
POWER
MADE IN USA
LEFT
~
RIGHT
MAIN INPUTS
RIGHT LEFT
CAUTION!CAUTION!CAUTION!CAUTION!
CAUTION!
Serial # Label
AMPLIFIER
MAIN OUTPUTS
RIGHT LEFT
To bypass the crossover within the subwoofer, simply locate the switch marked "out / in" on the back panel of the subwoofer and set to the "out" position. This will eliminate the internal crossover function.
Note
If not using an external crossover, you should use the built-in crossover for optimal performance.
Subwoofer out from A/V Processor
From the low pass output of your signal processor Install into right or left RCA line in connector in the back of the subwoofer or use a "Y" connector adapter into both right and left RCA line in connectors in the back of the subwoofer, and switch the crossover switch to "out".
Speaker-level connection
Figure 2 shows an easy way to connect your VA-907.2 subwoofer directly to your receiver or integrated amplifier.
When connected in this fashion, your satellite speakers will be crossed over at 85 Hz, which removes the lower bass from your speakers thus, enabling them to do a better job reproducing high frequencies.
You may also connect your satellites directly to your receiver or amplifier along with the subwoofer if you wish to bypass the internal high-pass crossover.
TO SATELLITE SPEAKERS
is already crossed over and designed to be used with a conventional amplifier and speaker. Combining both an external crossover and the one internal to the subwoofer may result in low output and increased noise. In these cases, to optimize your subwoofer perfor-
5
☞
Caution!
To avoid damage to your main amplifier, be sure to maintain correct polarity when making all connections. Red (positive) to red, and black (negative) to black. Be sure that all connections are tight, and that there are no loose strands or frayed wires.
continued. . .
6
☞
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use