Page 1
"If you know subwoofers, you know about Velodyne."
"... it's safe to say that when it comes to woofin' done right,
Velodyne's bigger models are probably the safest bet there is."
"... we just sat there marvelling at the sheer power and majesty of
this junior varsity Velodyne."
-Corey Greenberg
Home Theater Technology/February 1995
Face Off: Comparison of five subwoofers
Model Tested: VA-1012X
Velodyne Acoustics, Inc.
1070 Commercial St. Suite #101
San Jose, CA 95112
806/907
Owner's Manual
P/N: 63-610
408.436.7270 voice
408.436.7276 fax
Web Site: http//www.velodyne.com
E-mail: velodyne@earthlink.net
Printed on recycled paper.
Audio/Video Subwoofer System
Page 2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Caution
To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside.
Refer servicing to qualified service personnel.
The lighting flash with arrowhead symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point symbol is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the subwoofer.
1. Read Instructions -- All safety and operating instructions should be read before the subwoofer is operated.
2. Retain Instructions -- The safety and operating instructions should be retained for future reference.
3. Heed Warnings -- All warnings on the subwoofer and in the operating instructions should be adhered to.
4. Follow Instructions -- All operating and use instructions should be followed.
5. Water and Moisture -- The subwoofer should not be used near water -- for example, near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, near a swimming pool or the like.
6. Carts and Stands -- The subwoofer should be used only with a cart or stand recommended by the manufacturer.
7. Wall or Ceiling Mounting -- The subwoofer should be mounted to a wall or ceiling only as recommended by
the manufacturer.
8. Ventilation -- The subwoofer should be situated so that its location or position does not interfere with its proper
ventilation. For example, the subwoofer should not be situated on a bed, sofa, rug, or similar surface that may
block the ventilation openings; or placed in a built-in installation such as a bookcase or cabinet that may impede
the flow of air through the ventilation openings.
9. Heat -- The subwoofer should be situated away from heat sources such as radiators, heat registers, stoves,
or other subwoofers that produce heat.
10. Power Sources -- The subwoofer should be connected to a power supply only of the type described in the
operating instructions or as marked on the subwoofer.
11. Power-Cord Protection -- Power-supply cords should be routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience
receptacles, and the point at which they exit from the subwoofer.
12. "Caution: To prevent electrical shock, match wide blade of plug to wide slot, fully inserted." "Attention: Pour eviter
les chocs electriques, introduire lame la plus large de la fiche dans la borne correspondante de la prise et
pousser jusqu' au fond."
13. Cleaning -- The subwoofer should be cleaned only as recommended by the manufacturer.
14. Nonuse Periods -- The power cord of the subwoofer should be unplugged from the outlet when left unused for
a long period of time.
15. Object and Liquid Entry -- Care should be taken so that objects do not fall and liquids are not spilled onto the
enclosure.
16. Damage Requiring Service -- The subwoofer should be serviced by qualified service personnel when:
a. The power-supply cord or plug has been damaged.
b. Objects have fallen or liquid has been spilled into the subwoofer.
c. The subwoofer has been exposed to rain.
d. The subwoofer does not appear to operate normally or exhibits a marked change in performance.
e. The subwoofer has been dropped or damaged.
17. Servicing -- The user should not attempt to service the subwoofer beyond what is described in the operating
instructions.
SPECIFICATIONS VA-806 VA-907
Cabinet (incl. legs) 13"x12.8"x12.8" (H,W,D) 15"x15"x15"
Frequency Response 39hz-200hz +/- 3 dB...............................................
High Pass Crossover 85hz (6 dB/octave) ................................................
Low Pass Crossover 50hz - 150hz (6 dB/octave, 24 dB ultimate)..........
Amplifier Class A/B, 70 watts, Class A/B, 80 watts,
200 watts peak 200 watts peak
Woofer 6" forward firing 8" foward firing
Magnet 25 oz......................................................................
Voice Coil 1.5"........................................................................
Passive Radiator 8" downward firing 10" downward firing
Inputs Line-level & speaker-level.....................................
Outputs Line-level & speaker-level....................................
Warranty One year (parts & labor).......................................
Weight 38 lbs. (approx.) 44 lbs. (approx.)
Specifications are subject to change without notice.
FOR YOUR RECORDS. . .
DATE PURCHASED _______________________________
DEALER ________________________________________
SERIAL# ________________________________________
*NOTE: Please complete and return your warranty card within ten (10) days.
All other servicing should be referred to qualified service personnel.
1 10
☞
Page 3
signal sensing turn on/off that will automatically turn on the unit
when a signal is present at the inputs and turn off the unit after
several minutes when there is no longer any signal at the inputs.
Congratulations!
If you plan to leave the VA-806/907 unused for an extended period
of time, we recommend that you turn off the unit by the master power
switch on the rear panel.
Troubleshooting & Service
Before seeking service for your VA-806/907 subwoofer, please recheck all systems. Following is a simple troubleshooting guide to
assist you.
1. Verify unit is plugged in and power outlet used is active.
2. Is power switch on?
3. Is auto turn on/off set properly?
4. Is unit receiving an input signal from your source?
5. Have all controls on subwoofer (volume, crossover, phase,
etc.) been properly set?
The following conditions require service by a qualified technician:
1. The power cord has become damaged.
2. The unit does not appear to operate normally or exhibits a
marked change in performance.
3. The unit has been exposed to water.
4. Some part of the cabinet or circuitry is physically damaged.
Congratulations on your purchase of a Velodyne VA-806/907
subwoofer system. This system represents the state of the art in
accurate low frequency reproduction. Read and follow the instructions below to insure safe and proper system operation.
Warning!
To prevent fire or shock hazard, do not expose this equipment to
rain or moisture. To avoid electrical shock, do not open speaker
enclosure or amp chassis cover. Please observe all warnings on the
equipment itself. There are no user serviceable parts inside. Please
refer all service questions to your authorized Velodyne dealer.
Prior to installation
Please unpack the system carefully. Remove all staples used to
seal the carton as they can scratch the cabinet. Please save the
carton and all packaging materials for future use. Record the serial
number in the space provided on the warranty card for future
reference.
Product Features & Controls
● Built in power amplifier
● Adjustable (50 to 150hz) low-pass crossover
● 85hz high-pass crossover
● Line-level inputs & outputs
● Speaker-level inputs & outputs with spring clips
● Signal sensing auto turn on/off with bypass option
● Variable volume control
● selectable phase control (0 or 180 degrees)
● Magnetically shielded for video use
Thank you for purchasing a Velodyne!
9
☞
continued. . .
2
☞
Page 4
Installation
Your new VA-806/907 subwoofer system provides for a number of
installation options. Read all the installation information below in
order to determine which installation option is best for your system.
Remember to perform all installation procedures with system
power turned off.
Inputs
Your new VA-806/907 subwoofer is equipped with both speakerlevel and line-level inputs. Use the LINE-IN jacks when connecting
your subwoofer to a pre-amp, signal processor, or line-level crossover. The FROM AMPLIFIER jacks connect directly to the speaker
outputs of a integrated amplifier or receiver. Your amplifier section
will notice no additional loading effects when you use these inputs
because of their high impedance.
Note
Do not use both LINE-IN and FROM AMPLIFIER inputs simultaneously.
Volume control
This control allows you to balance the output from the subwoofer to
the main speakers in your system. To adjust the volume, start with
the volume knob indicator at the "MIN" setting. With your other
speakers playing, rotate the knob clockwise until you create a
volume balance with your speakers. In most cases this will be
somewhere between the "10 o'clock" and "2 o'clock" positions on
the dial.
When using a pair of VA-806/907 subwoofers in stereo, it is
preferable to place each subwoofer adjacent to the satellite of the
same channel.
Keep in mind that frequency response and output level can be
drastically influenced by placement depending on the acoustic
properties of the listening room. Typically the VA-806/709 will
sound louder when placed next to a wall or in a corner.
Caution!
The VA series subwoofers have amplifiers built into the cabinet. Do
not place the cabinet next to sources of heat such as furnace
registers, radiators, etc. The power cord should be routed in such
a way that it will not be walked on, pinched, or compressed in any
way.
Regardless of where you install your VA-806/907 subwoofer, it
must remain in an upright position (passive radiator facing downward). Using, shipping, or otherwise storing the VA-806/907 subwoofer in any other position for an extended period of time may
result in damage to the unit not covered by warranty.
The VA-806/907 Subwoofer is magnetically shielded to reduce
magnetic emission from its cabinet to increase the number of
possible locations available for placement. However, this shielding
may not be adequate for all installations. Certain types of televisions
are particularly sensitive to stray magnetic fields. If your television
produces distorted colors after installation of your VA-806/907
subwoofer, simply increase the distance between your television
and the VA-806/907 until normal color and operation is returned.
Care of your subwoofer
Warning - Turning the volume to "MAX" setting may dam-
age the subwoofer with certain source material.
Low-pass crossover
Both sets of inputs sum the left and right channels together and the
resulting signal is passed through an adjustable low-pass crossover
before being amplified. The crossover control allows you to adjust
the upper limit of the subwoofer's frequency response from 50 to
3
☞
Do not use any harsh detergents or chemicals to clean the cabinet.
Abrasives, detergents, or cleaning solutions may damage the finish
on the cabinet. We recommend using a damp cloth to clean the
cabinet.
During normal conditions, the VA-806/907 subwoofer may be left on
continuously without any problems. The unit is equipped with a
continued. . .
8
☞
Page 5
Figure 2: Installation using speaker-level (from amplifier) inputs
PHASE
FREQUENCY
+ -
CAUTION!CAUTION!CAUTION!CAUTION!
CAUTION!
WARNING:
AVIS:
+ R - - L +
MAIN OUTPUTS
(speaker-level)
INTEGRATED AMP / RECEIVER
VOLUME
+ -
SATELLITE SPEAKERS
150 hz. The subwoofer's response will begin rolling off above the
frequency you set this control to.
You should set the crossover frequency to obtain a smooth and
seamless transition from the subwoofer to the main speakers in
your system. If your main speakers are smaller units with limited low
frequency output, you may wish to choose a higher frequency (such
as 100-120hz) than you would with larger speakers which have
greater low frequency output. With larger speakers, you might start
with this control set lower, such as 80hz.
Phase adjustment
This control allows you the ability to compensate for having the
subwoofer in a different location than the main speakers. Ideally,
you will have the sound from the subwoofer reach the listening
position the same time as the sound from the main speakers.
However, if the distance from the listening position to the subwoofer
and the distance from listening position to the main speakers differs,
the sound from each will reach your ears at a different time.
This control allows the signal to be delayed 180 degrees so the
output of the subwoofer will blend in to that of your main speakers
without any cancellation.
Interconnect cables
When installing your VA-806/907 using the line-level inputs/outputs, you should use standard shielded phono cables. Always keep
the lines as short as practical to minimize noise.
When using the speaker-level inputs/outputs, use the same quality
speaker cable to your subwoofer as you run to your satellites.
Placement
The VA-806/907 operates at very low frequencies which are primarily non-directional. While it is recommended that the subwoofer be
placed on the same plane as the satellite speakers, room and
system conditions often dictate otherwise. See your dealer for help
in placement.
7
☞
Auto turn on switch
The auto turn on switch allows the user to bypass the auto turn on
function if desired. When set in the "auto" mode with main power on,
the VA-806/907 will turn itself on when an input signal is present. If
no signal is present, after several minutes the unit will shut itself off.
When set in the "on" mode, the auto turn on/off function is bypassed
and the unit will be on whenever the main power switch is on.
Power switch
The master power switch is located on the right half of the unit. This
slide style switch is the main on/off for the unit. This switch should
be set to up for on , down for off.
continued. . .
4
☞
Page 6
Line-level connection
Figure 1 shows connection to a pre-amplifier's main outputs and
returning them to your amplifier inputs.
When installed in this fashion, your satellite speakers will be
crossed over at 85hz, which removes the lower bass from your
amplifier and speakers thus, enabling them to do a better job
reproducing high frequencies. By utilizing this method, you will have
a bi-amplified system, gaining improved power and headroom for
your system.
A word about subwoofer outputs
The Velodyne subwoofer is designed to operate using the full range
audio signal for input when using the built-in crossover. Some
surround sound processors/receivers have a "subwoofer out" jack
that is already crossed over and designed to be used with a
conventional amplifier and speaker. If this is the case, you should
set the low pass crossover to 150Hz.
Note
If not using an external crossover, you should use the built-in
crossover for optimal performance.
Subwoofer out from A/V
Processor
WARNING:
AVIS:
PRE-AMP
MAIN OUTPUTS
RIGHT LEFT
Figure 1: Installation using line-level (line in) inputs
PHASE
FREQUENCY
AMPLIFIER
CAUTION!CAUTION!CAUTION!CAUTION!
CAUTION!
VOLUME
MAIN INPUTS
RIGHT LEFT
TO SATELLITE SPEAKERS
MAIN OUTPUTS
RIGHT LEFT
From the low pass output of your signal processor Install into right
or left RCA line in connector in the back of the subwoofer or use a
"Y" connector adapter into both right and left RCA line in connectors
in the back of the subwoofer.
Speaker-level connection
Figure 2 shows an easy way to connect your VA-806/907 subwoofer
directly to your receiver or integrated amplifier.
When connected in this fashion, your satellite speakers will be
crossed over at 85hz, which removes the lower bass from your
speakers thus, enabling them to do a better job reproducing high
frequencies.
You may also connect your satellites directly to your receiver or
amplifier along with the subwoofer if you wish to bypass the internal
high-pass crossover.
Caution!
To avoid damage to your main amplifier, be sure to maintain correct
polarity when making all connections. Red (positive) to red, and
black (negative) to black. Be sure that all connections are tight, and
that there are no loose strands or frayed wires.
continued. . .
5
☞
6
☞
Loading...