BG-N12
BAT T ERY GRIP
Designed for the Nikon
D3100/D3200/D3300 SLR Cameras
Introduction
Thank you for choosing Vello and congratulations
on your new BG-N12 bat tery grip purchase. Enjoy
the many benefi ts that a battery grip offers , such as
extended shooting time and more control and comfor t
when shooting in a vertical (portrait) orientation.
The Vello BG-N12 is compatible with the Nikon D3100/
D3200/D3300 DSLR camera s. The BG-N12 accepts
up to two Nikon EN-EL14 or EN-EL14a rechargeable
batteries (not included). The BG-N12 is equipped
with an alternate shu tter-relea se button that trig gers
the camera via the included shutter release cable for
shooting in a vertical position.
Please read through this
entire manual before using the BGN12 battery grip.
2
Precautions
1. The BG-N12 should only be used w ith compatible
devices specified in this manual.
2. Only use with batteries recommended in this
manual. The BG -N12 can not be used with other
battery holders.
3. Cover the power terminals with the contact cap
when the BG-N12 is not in use. This prevents
electrical shor ts caused by metal object s touching
the power terminals.
4. If you notice smoke, an unusual smell or noise from
the bat tery pack, discontinue use immedia tely.
Remove the batteries and take the device to a Vello
authorized reseller.
5. The BG-N12 does not have a power switch.
Instead, use the camera power switch to turn the
power on or off.
6. The battery level may not display properly if
batteries are inser ted before mounting the grip.
7. Remove bat teries from the grip when not in use .
8. Do not attempt to disassemble.
9. Avoid water or extreme humidit y and keep in a dry
and cool place.
10. Keep out of reach of children.
3
OVERVIEW INTRODUCTION
ASSEMBLY
Overview
7
1
6
5
2
11
3
4
10
8
9
12
4
1
Tripod Socket
Allows the camera to be mounted to a
tripod w hen the grip is mounted.
5
Attachment Wheel
Secures the grip to the camera’s
tripod socket.
9
Battery Chamber Cover
Secures up to two Nikon EN-EL14 or
EN-EL14a batteries.
2
Hand Strap Mount
Provides bottom mounting position
for the use of a hand str ap.
3
Shutter Release Button
Use as an alternate shutter release
button for shooting in ver tic al
(portrait) mode.
4
Camera Battery Door Holder
Stores the camer a’s battery chamber
door when the grip is mounted.
Power Sour ce Two Nikon EN- EL14 or EN-EL14a Rechar geable Batte ries
Operating Temperature 32 – 104 °F (0 – 4 0 °C)
Dimensions 5" × 3.1" × 4" (12.6 × 8 × 10 cm)
Weigh t 4.8 oz. (138 g ) excluding batte ries
6
Anti-Slip Rubber Grip
Provides secure and comfor table grip
when shooting vertically.
7
Contact Cap
Protects metal power contacts.
Keep this cap on when the grip is not
connected to the camera.
8
Power Contacts
Slides into the ca mera’s batter y
chamber and transmits power.
10
Cable Connecting Socket
Accepts sub mini connector of the
shutter release cable.
11
Mounting Screw
Connec ts to the camera’s tripod
socket.
12
Shutter Release Cable
Transmits shut ter release signal from
battery grip to the camera .
5
OVERVIEW INTRODUCTION
ASSEMBLY
Attaching The Grip
35º
1. Ensure that the power is
turned off on the camera .
2. Turn the camera upside
down and open the
camera battery chamber.
Pull gently at a 35º angle
until the chamber door
comes loose.
6
3. Slide the camera batter y
chamber door into the BGN12 chamber door holder
in order to avoid loss .
4. Insert the BG-N12 grip
GPS
power contacts into the
camera’s battery chamber
as shown. Make sure to
align the camera’s tripod
socket with the BG-N12
mounting screw.
5. Rotate the attachment
wheel in the direc tion
shown by the arrow until it
is firmly tightened.
6. Connect the shut ter release
cable from the socket on the
end of the ba ttery grip to the
remote release/GPS port on
the D3100 /D3200 /D33 00 body.
7. Turn the camer a on and check
the bat tery level on the LCD or
viewfinder.
When removing the grip, turn the
camera power off, remove batteries,
and replace the protective contact cap.
OVERVIEW INTRODUCTION
7
ASSEMBLY
ONE-YEAR LIMITED WARRANTY
This VELLO product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use
for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later. The warranty provider’s
responsibility with respect to this limited warranty shall be limited solely to repair or replacement, at the provider’s discretion, of any product
that fails during normal use of this product in its intended manner and in its intended environment. Inoperability of the product or part(s) shall
be determined by the warranty provider. If the product has been discontinued, the warranty provider reserves the right to replace it with a
model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse, improper installation or maintenance.
EXCEPT AS PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY IMPLIED
WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. This warranty provides you with specific legal rights, and you may also have additional rights that vary from state to
state.
To obtain warranty coverage, contact the Vello Customer Service Department to obtain a return merchandise authorization (“RMA”) number,
and return the defective product to Vello along with the RMA number and proof of purchase. Shipment of the defective product is at the
purchaser’s own risk and expense.
For more information or to arrange service, visit www.vellogear.com or call Customer Service at 212-594-2353.
Product warranty provided by the Gradus Group.
www.gradusgroup.com
VELLO is a registered trademark of the Gradus Group. © 2014 Gradus Group LLC. All Rights Reserved.
www.vellogear.com
All other trademarks are the property of their respective owners
© Copyright 2014 Gradus Group LLC
GG2
Loading...