Velleman К8058 User Manual

8 Channel RF transmitter

K

n

a

m

e

l

l

e

V

h

t

i

w

e

s

u

r

o

F

e

s

s

e

r

d

a

Total solder points: 63
Difficulty level: beginner 1 2  3 ⌧ 4  5  advanced

w

o

l

l

a

s

u

e

h

t

n

o

f

o

e

s

o

o

r

e

8
m
m

0

e

l

p

i

t

l

u
.

v

i

e

c

e

r

n

i

s

r

e

8

,

d

r

a

c

y

a

l

e

r

6

5

K8058

K8058

ILLUSTRATED ASSEMBLY MANUAL H8058IP-1

Features & specifications

Features:

 Works together with the K8056 relay card.
 8 addresses allow the use of multiple receivers.
 'all clear'- function.
 Toggle or momentary mode for each key.
 Open-field range up to 50m.
 Rubber keypad.

Specifications:

• 433MHz operation

• LED function/mode indication

• Power supply: 3 AAA batteries (not included).

• Dimensions: 150 x 58 x 20mm (5.9" x 2.3" x 0.8")

Schematic diagram.

C1
100n

GND+V

2

RA5/T1CKI/OSC1/CLKIN

RA0/CIN+/ICSPDAT

3

RA4/T1G/OSC2/CLKOUT

RA2/COUT/T0CKI/INT

4

RA3/MCLR/Vpp

5

RC5

6

RC4

7

RC3

GND

C3
56p

L2

COIL PCB 433

C2
1p

L1

COIL 1T 433

C4
4p7

GND

GND

R1
47

T1
MPSH10

R6
220

GND

R2
33K

X1
SAW433

GND

C5
100p

R4
33KR533K

J1
J2

Address selecti o n

GND

LED3RL
LD1

GND

+V+V

33K

R3

1K

470

R7

+V

1

VDD

IC1

RA1/CIN-/ICSPCLK

RC0

RC1

RC2

VSS

PIC16F630-I/P

14

GND

13
12
11

10

SW1

1

9

SW4

4

8

SW5

7

SW2

SW6

SW7

2

5

8

SW3

SW8

SW9

SHIFT

SW10

SHIFT

3

6

2

Assembly hints

0

.

0

0

0

1. Assembly (Skipping this can lead to troubles ! )

Ok, so we have your attention. These hints will help you to make this project successful. Read them
carefully.

1.1 Make sure you have the right tools:

• A good quality soldering iron (25-40W) with a small tip.

• Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to

give it a wet look. This is called ‘thinning’ and will protect the tip, and enables you to
make good connections. When solder rolls off the tip, it needs cleaning.

• Thin raisin-core solder. Do not use any flux or grease.

• A diagonal cutter to trim excess wires. To avoid injury when cutting excess

hold the lead so they cannot fly towards the eyes.

• Needle nose pliers, for bending leads, or to hold components in place.

• Small blade and Phillips screwdrivers. A basic range is fine.

For some projects, a basic multi-meter is required, or might be handy

1.2 Assembly Hints :

leads,

⇒ Make sure the skill level matches your experience, to avoid disappointments.
⇒ Follow the instructions carefully. Read and understand the entire step before you perform each

operation.

⇒ Perform the assembly in the correct order as stated in this manual
⇒ Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.
⇒ Values on the circuit diagram are subject to changes.
⇒ Values in this assembly guide are correct*
⇒ Use the check-boxes to mark your progress.
⇒ Please read the included information on safety and customer service

⇒ * Typographical inaccuracies excluded. Always look for possible last minute manual updates,

indicated as ‘NOTE’ on a separate leaflet.

3

Assembly hints

1.3 Soldering Hints :

1- Mount the component against the PCB surface and carefully

solder the leads

2- Make sure the solder joints are cone-shaped and shiny

3- Trim excess leads as close as possible to the solder joint

REMOVE THEM FROM THE TAPE ONE AT A TIME !

AXIAL COMPONENTS ARE TAPED IN

THE CORRECT MOUNTING SEQUENCE !

Velleman hereby certifies that the device K8058 meets the essential requirements and all other relevant

For the complete conformity declaration check out :http ://www .velleman.be/downloads/doC/CE_K8058.pdf

stipulations of directive 1999/5/EG and 1995/5/EC.

4