i / iii
INSTALLATION & USER MANUAL
Auto Tracking / High Speed PTZ Camera
ii / iii
Thank You for Choosing Our PTZ Camera!
When you open the box:
Check that the packing and the contents are not visibly damaged. Contac t the retailer immediately if any parts are
either missing or damaged.
Make sure if the contents are all included as per the packing list.
Do not attempt to use the device with missing or damaged parts. Send the product back in its original packing if it is
damaged.
The information contained in the document is subject to change without notice.
iii / iii
Table of Contents
1. Safety Notes --- Important!!! ............................................................................................................................. 1
2. About The Product ............................................................................................................................................ 2
2.1. Features .................................................................................................................................................. 2
2.2. Functions ................................................................................................................................................. 2
2.3. Technical Parameters .............................................................................................................................. 4
2.3.1. SONY Modules & Veilux Modules ............................................................................................... 4
3. Installation ......................................................................................................................................................... 5
3.1. DIP Switch Setting ................................................................................................................................... 5
3.2. Installation ............................................................................................................................................... 5
3.2.1. Wall Mount Installation ................................................................................................................. 5
3.2.2. In-ceiling Mount Installation.......................................................................................................... 7
3.2.3. Surface Mount Installation.......................................................................................................... 10
3.2.4. Pole Mount Installation............................................................................................................... 11
4. Operation Guide .............................................................................................................................................. 12
4.1. Operation At Power Up .......................................................................................................................... 12
4.2. How To Use Our Control Keyboard ....................................................................................................... 12
4.2.1. Control Keypad Password And Access...................................................................................... 12
4.2.2. Control Keypad Command Syntax ............................................................................................. 12
4.2.3. Control Keypad Command Types .............................................................................................. 13
4.3. Select A Camera ................................................................................................................................... 13
4.4. Camera Motions .................................................................................................................................... 13
4.4.1. Pan And Tilt ............................................................................................................................... 13
4.4.2. Zoom.......................................................................................................................................... 14
4.4.3. Focus ......................................................................................................................................... 14
4.4.4. IRIS Opening ............................................................................................................................. 14
4.4.5. Preset Positions Programming and Recalling ............................................................................ 15
4.5. Function Program Menu ........................................................................................................................ 15
4.5.1. Product Information.................................................................................................................... 16
4.5.2. Display Setup ............................................................................................................................. 16
4.5.2.1. Label Position ................................................................................................................... 17
4.5.3. Main Programming Menu (Dome Settings 1) ............................................................................. 17
4.5.3.1. Camera ............................................................................................................................. 18
4.5.3.2. Motion ............................................................................................................................... 20
4.5.3.3. Power Up .......................................................................................................................... 22
4.5.3.4. Presets.............................................................................................................................. 22
4.5.3.5. Patterns ............................................................................................................................ 23
4.5.3.6. Zones ................................................................................................................................ 24
4.5.3.7. Clear Set........................................................................................................................... 24
4.5.3.8. Preset Number.................................................................................................................. 25
4.5.4. Secondary Programming Menu (Dome Settings 2).................................................................... 25
4.5.4.1. Alarm Submenu ................................................................................................................ 25
4.5.4.2. Address setting................................................................................................................. 26
4.5.4.3. Password .......................................................................................................................... 27
4.5.4.4. Windows Blanking ............................................................................................................ 28
4.5.4.5. Heater Setting ................................................................................................................... 30
4.5.4.6. Cruise Setting ................................................................................................................... 30
4.5.4.7. Tracking Setting ................................................................................................................ 31
4.5.5. Dome Label................................................................................................................................ 33
4.6. Special Control Panel Commands ......................................................................................................... 34
5. Trouble Shooting............................................................................................................................................. 35
6. Annex ............................................................................................................................................................... 36
6.1. DIP Switch Chart ................................................................................................................................... 36
6.2. OSD Menu Diagram .............................................................................................................................. 41
1 / 43
1. SAFETY NOTES --- IMPORTANT!!!
The following important notes must be followed carefully to run the PTZ camera and respective accessories in total safety.
The camera and relative accessories are called video system in this section.
Use the instructions correctly and fully
Read all safety rules and instructions carefully before starting to run the video system.
Follow the instructions in the instruction manual. Pay attention to all warnings on the camera and in the instruction manual.
Keep the safety notes and instructions for future reference.
Attachments & Accessories
Do not use attachments other than those recommended in the instruction manual because this could cause risks to the
products. Only use the recommended accessories for the camera for installation and operation.
Protect the video system
To protect the camera, avoid installing and using it in direct sunlight or any source of bright light. Bright light, like that from
a spotlight, can cause dimming and blurs. A vertical line may appear on the screen. This does not indicate a problem.
Keep it away from rain and dust. Do not touch the zoom lens with your fingers. If needed, use a soft cloth and methylated
spirit to remove traces of dust. Apply a specific cap to protect the zoom lens when the camera is not in use.
Install the camera away from video interference. The pictures could present interference if the leads are arranged near a
TV set or other device. Either move the leads or re-install the device to solve the problem.
Do not use any part of the video system near water, i.e. bathtubs, wash basins, sinks, tubs, on damp surfaces, near
swimming pools, etc. Do not insert objects of any kind through the camera openings to avoid touch live parts: fire and
electrocution risk. Do not pour any kind of liquid on the device.
A switch for performing maintenance operations on the camera must be included. Connect the camera only to the
electrical power supply shown on the ratings plate. Contact your retailer if in doubt.
Lay the power wires keeping them from being trodden on or squeezed by objects plac ed on top of them. Pay particular
attention to leads near plugs, screws and the product outlet.
Disconnect the power lead and the wiring to protect the camera during electrical storms or when it is left unattended and
not used for a long time. This will prevent damage to the video system in the event of lightening or electrical line overload.
Do not overload the electrical power and the extensions to prevent the risk of fire or electrocution.
Do not place the camera near or over radiators or sources of heat. Check that the area is suitably ventilated before
installing the camera inside partially closed areas (such as recesses, bookshelves and shelves).
Do not position the camera on unsteady trolleys, stands, brackets or tables. The camera could fall and severely injury
adults and children in addition to seriously damaging the product.
Maintenance & Repairs
Always contact a qualified service technician to repair the camera (or any other part o f the video system). Unauthorized
opening or removing the lids may cause fire and electrocution risk and other dangers.
Disconnect all electrical parts from the mains before cleaning.
Uses spare parts specified by the manufacturer or spare parts with equivalent characteristics when replacements
required. Unauthorized replacements can cause fires, electrical shocks and other dangers.
After any servicing intervention or repair to the video system, ask the technician to run a safety check to ensure that
everything is working safely.
Damage requiring professional assistance
Disconnect the video system from the power mains and call qualified service personnel in the following cases :
If the power lead or plug is damaged.
If liquid or foreign objects accidentally penetrate inside the device.
If the device was exposed to rain or water.
If the device was dropped, subjected to heavy shocks or if the camera packaging was damaged.
If the device performance changes considerably.
2 / 43
2. ABOUT THE PRODUCT
The tracking PTZ is based on our unique motion tracking technology with high position resolution, high speed, low price
and selectable communication protocols. It is widely used in surveillance system as unattended CCTV device.
2.1. FEATURES
Auto tracking of moving object (auto PTZ) based on our motion tracking technology;
0.01Lux of module specifications;
360º horizontal rotation at maximum speed of 240º /sec;
Auto cruise function with 256 preset positions;
Built-in OSD Menu, to change dome parameter, achieve auto scan, and pattern etc;
Features password protection to prevent unauthorized changes to the dome setting;
Windows blanking and tracking boundary for privacy purpose;
EasyClip installation features;
The feature of defining specific activity when the dome parks;
Auto-flip to follow object and surveillance of any subject that is constant and continuous;
The speed can be adjusted automatically according to zooming times;
Auto focus lens and auto white balance, BLC function;
Multi protocol compatible (Pelco-P, Pelco-D etc);
Alarm input, Alarm output, Alarm action.
2.2. FUNCTIONS
Object Tracking
In auto tracking mode, the camera can track a moving object in the target area with auto pan, tilt and zoom which realizes
smart unattended surveillance.
Tracking Cruise
The tracking function can be activated during cruise. At a preset of the cruise list, the camera can track moving objects
automatically.
Soft Address
The camera address can be programmed with built-in OSD menu, and the user does not need to dismount the camera
from field or do any screw work.
Wide Dynamic Range (WDR)
A camera is intended to provide clear images even under back light circumstances where intensity of illumination can
vary excessively, when there are both vary bright and vary dark areas simultaneously in the field of view. W DR enables
the capture and display of both bright areas and dark areas in the same frame, in a way that there are details in both
areas, i.e. bright areas are not saturated, and dark areas are not too dark. Please note that WDR function is not available on
all models.
Day/Night Function
The IR cut filter of camera module inside the camera can be removed by sending special command, so that the camera
can change from color to mono. The picture is clear even if the illumination is as low as 0.01Lux.
Wide Dynamic Range (WDR) and Day/Night function are based on the relative modules. Please refer to technical
parameters.
Proportional Pan
Proportional pan automatically reduces or increases the pan and tilt speeds in proportion to the zooming times. At
telephoto zoom settings, the pan and tilt speeds will be slower for a given amount of joystick deflection than at wide zoom
settings. This keeps the image from moving too fast on the monitor when there is a large amount of zoom.
Auto Flip
When the camera tilts downward and goes just beyond the vertical angle, the camera rotates 180º. W hen the camera
rotates (flips), the camera starts moving upward as you continue to hold joystick in the down position. Once you let go of
the joystick after the dome rotates, joystick control returns to normal operation. The auto-flip feature is useful for following
a person who passes directly beneath the camera.
Save/Call Preset
Preset function is that dome saves current horizontal angle and title angle of pan/tilt, zoom and position parameters into
3 / 43
memory. W hen necessary dome calls these parameters and adjusts Pan/Tilt and camera to that position. User can save
and call presets easily and promptly by using keyboard controller or infrared controller. The camera supports up to 256
presets.
Lens Control
1) Zoom control
User can adjust zoom wide or tele by controller to get desired image.
2) Focus control
System defaults Auto Focus mode, that is, the lens and camera will automatically adjust the focus to get the best image.
Focus can also be controlled manually from the controller if required. Press Focus Near or Focus Far key to manually
focus. Focus can be manual via keyboard or matrix, please refer to control keyboard or matrix operation manual for
detailed operation. W hen adjusting position is set with focus status, it goes back to auto focus.
The camera will NOT auto focus in the following status.
Target is not in the center of image.
Targets are in near and far at the same time.
Target is of strong light object. Such as spotlight etc.
Target is behind the glass with water drop or dust.
Target moves too fast.
Large area target such as wall.
Target is too dark or vague.
3) IRIS control
System defaults Auto IRIS. Camera can adjust immediately according to the alteration of back ground illumination so that
a lightness steady image can be achieved.
You may adjust IRIS by controller to get required image brightness, and call back Auto IRIS by controlling the joystick.
Auto White Balance
Camera can automatically adjust white balance (W B) according to the alteration of background lightness to give a true
color image.
Back Light Compensation (BLC)
If a bright backlight presents, the subjects in the picture may appear dark or as a silhouette. Backlight compensation
enhances objects in the center of the picture. The camera uses the center of the picture to adjust the IRIS. If there is a
bright light source outside this area, it will wash out to white. The camera will adjust the IRIS so that the object in the
sensitive area is properly exposed.
Auto Cruise
The preset position is programmed to be recalled in sequence. This feature is called auto cruise. Up to 30 presets can be
saved in each cruise tour.
Patterns
A pattern is a saved, repeating, series of pan, tilt, zoom and preset functions that can be recalled with a command from a
controller or automatically by a programmed function (alarm action or park action or power-up action).
Auto, Random and Frame Scan
Auto Scan: Make the camera scan 360º ranging from the current position.
Random Scan: Make the camera random scan 360º ranging from the current position.
Frame Scan: This feature freezes the scene on the monitor when going to a preset. This allows for smooth transition from
one preset scene to another.
Zones Setting
A zone is a pan area, defined by a left and right limit, on the 360º pan plane. The camera has eight zones, each with a
6-character label.
Alarms Input
The camera has four alarm inputs, which can be programmed as high, medium or low priority. W hen an alarm is received,
an input signal to the camera triggers the user-defined action (go to preset, run pattern, etc.) programmed for the alarm.
Auxiliary Output
An auxiliary output is a programmable signal from the camera back box that can trigger another device to operate. An
auxiliary output is programmable to trigger from an alarm or from a controller.
Password Protection
The camera features password protection to prevent unauthorized changes to the camera settings. You can open the
System Information and Display Setup Screens, but cannot access any of the camera Settings menus.
Windows Blanking
A set window can be saved so that it is the only blanked tilt area of the scene. All other parts of the tilt area of the scene
will be visible.
Windows blanking is only available for Sony Modules at present.
2.3. TECHNICAL PARAMETERS
2.3.1. SONY & VEILUX MODULES
Model # VP-F18X (18X) VP-AT18X (18X) VP-ATDN18X (18X)
Module Brand Sony Sony Sony
Signal Format PAL/NTSC PAL/NTSC PAL/NTSC
Image Sensor ¼ inch color CCD ¼ inch color CCD ¼ inch color CCD
H. Resolution 550 TVL 550 TVL 550 TVL
Video Out 1.0±0.2VP-P 1.0±0.2VP-P 1.0±0.2VP-P
P/T Speed
Pan:0.05º～240º/sec
;Tilt:0.03º～160º/sec
Pan:0.05º～240º/sec;Tilt:0.03º～160º/sec Pan:0.05º～240 º/sec;Tilt:0.03º～160º/sec
S/N Ratio ≥50DB ≥50DB ≥50DB
AGC Auto/Manual Auto/Manual Auto/Manual
BLC Auto/Manual Auto/Manual Auto/Manual
IR cut Filter Yes Yes Yes
(WDR) No No No
Optical Zoom 18X 18X 18X
Digital Zoom 12X 12X 12X
Model # VP-FDN27X (27X) VP-ATDN27X (27X) VP-ATDN36X (36X)
Module Brand Veilux Veilux Sony
Signal Format PAL/NTSC PAL/NTSC PAL/NTSC
Image Sensor ¼ inch color CCD ¼ inch color CCD ¼ inch color CCD
H. Resolution 580 TVL 580 TVL 520 TVL
Video Out 1.0±0.2VP-P 1.0±0.2VP-P 1.0±0.2VP-P
P/T Speed
Pan:0.05º～240º/sec
;Tilt:0.03º～160º/sec
Pan:0.05º～240º/sec;Tilt:0.03º～160º/sec Pan:0.05º～240 º/sec;Tilt:0.03º～160º/sec
S/N Ratio ≥50DB ≥50DB ≥50DB
AGC Auto/Manual Auto/Manual Auto/Manual
BLC Auto/Manual Auto/Manual Auto/Manual
IR cut Filter Yes Yes Yes
(WDR) No No Yes
Optical Zoom 27X 27X 36X
Digital Zoom 10X 10X 12X
Table 1: Sony Modules
The specifications are subject to change without
4no/t4ic3
e.
5 / 43
3. INSTALLATION
This section contains detailed instructions for installing the camera. These instructions assume that the installer has a
good knowledge of installation techniques and is capable of adopting safe installation methods.
3.1. DIP SWITCH SETTING
Before installing the camera drive, check the DIP switches; configure the receiver address, communication protocol, and
baud rate setting. Pic. 1 shows switches position and default settings. SW 1 switches (1bit) and SW 2 switches (1, 2, and 7
bit) are set to the ON position. For normal user, setting switches to default position is enough.
Pic. 1 Switch Position
The camera can be controlled via various communication protocols by setting SW 1 switches(1, 2, 3,and 4) and operate at
1200bps, 2400bps, 4800bps, 9600bps and 19200bps baud rate by setting SW 1 switches(5, 6, 7, and 8). Do not set the
switches to reserved position. Pic. 2 shows the default settings for the DIP switches.
Pic. 2 Default settings of DIP switches
Please refer to Table 28: SWITCH1 SETTING and Table 29: SWITCH2 SETTING in Section 6.1 to set baud rate, and
communication protocol type and camera address.
Always use the “PELCO P” or “PELCO D” protocols.
Do not use address “0” with the “PELCO P” or “PELCO D” protocols.
3.2. INSTALLATION
The camera has four types of mountings: wall mount, in-ceiling mount, surface mount, and pole mount. Please make sure
which type you are installing.
3.2.1. WALL MOUNT
Step 1. Install the power box on wall
INSTALLATION
(WITH POWER BOX)
Pic. 3
Install the power box to the wall with 4 screws.
When installing outdoors, make sure installation is properly sealed to keep moisture out.
6 / 43
Pic. 6.
e back box. Take out hole of pin. Screw the me
To install the ptz camera with no power box, install the bracket directly onto the wall and then go to Pic 6.
Pic. 4
Pull the cables (of video, alarm, control etc.) through the cable hole of the power box and do necessary connections. The
cables are supplied by user.
Pic. 5
Refer to the instructions supplied with the bracket. Take out cables for the dome through the bracket. And install the
bracket to the power box. See Pic. 5
Press the thumb fas tener and open the hinged door to th tal cover into the
bracket. See
Connect cables to hole of pin. Insert the pin inside the back box. W hen finished, close the door to the back box and turn
on the power. The LED will light up. See Pic. 7.
If the LED does not light up, refer to Section 5: Trouble Shooting.
Step 2. Install dome drive
Pic. 6
Pic. 7
7 / 43
Pic. 8
Set the DIP switches for SW1 and SW 2 at the bottom of the dome drive for the appropriate receiver address,
communication protocol, and baud rate. Refer to the labels on the dome drive or DIP SWITCH SET at the beginning of
this manual.
Remove cover of camera and sponge. See Pic. 8.
Pic. 9
Line up link card and faucet of the back board of the dome. Push the dome drive in. See Pic. 9.
Step 3. Install lower dome.
Pic. 10
Take out a screw from lower dome. Link cables, screw, and lower dome. See Pic. 10.
Pic. 11
Line up the mounting screw holes, and install the two mounting screws. Push the lower dome inside the back box. See
Pic. 11.
Pic. 12
Screw the two mounting screws, and screws in the bracket. See Pic. 12.
3.2.2. IN-CEILING MOUNT INSTALLATION
8 / 43
Step 1. Prepare In-ceiling
Locate the center point of the in-ceiling mounting location. Insert the compass tool into the hole. Draw a circle on the
ceiling using the compass tool and a pencil. See Pic. 14 (Left).
Pic. 13
Cut the circle out of the ceiling tile. See Pic. 14 (Right).
Put the reinforcing metal plate (see following pic.) on top of the ceiling (behind the ceiling) with the two circles aligned
vertically.
Step 2. Install back box
Pic. 14
Pic. 15
Pic. 16
Take out bracket from back box. Insert the back box into ceiling. See Pic. 16.
Install a safety chain/cable (not supplied) that can stand up to 32 pounds (14.6kg). Press the thumb fastener and open the
hinged door to the back box. Take out hole of pin. See Pic. 17
9 / 43
Pull Cables into the back box throughthe plastic panel. Cannect cables to hole of pin. See Pic. 18
Pic. 17
Pic. 18
Insert the hole of pin inside the back box. When finished, close the door to the back box and turn on the power. The LED
will light up. See Pic. 19.
Pic. 19
If the LED does not light up, refer to Section 5: Trouble Shooting.
Step 3. Install dome drive
Set the DIP switches for SW1 and SW 2 at the bottom of the camera drive for the appropriate receiver address,
communication protocol, and baud rate. Refer to the labels on the camera drive or DIP SW ITCH SET in this manual.
Remove cover of camera and sponge. See Pic. 20
Pic. 20
Line up link card and faucet of the back board of the dome. Push the dome drive in. See Pic. 21
10 / 43
r dome
Step 4. Install lowe
Pic. 21
Take out a screw from lower dome. Link cables, screw, and lower dome. See Pic. 22.
Pic. 22
Pic. 23
Line up the snaps on trim ring with the mounting screws on the back box. Snap the trim ring into the plastic snap washers
on the mounting screws. See Pic. 23.
3.2.3.
SURFACE
MOUNT INSTALLATION
Step 1. Install back board of surface mount
Pic. 24
Locate the back board of the camera location. Drill a hole in the ceiling using a drill. Insert the screw and back board into
the hole. See Pic. 24
Pic. 25
Press the thumb fastener and open the hinged door to the back box. Take out hole of pin. See Pic. 26.
11 /
Pull cables into the back box into the plastic panel. Connect cables to hole of pin. Insert the hole of pin inside the back
board. W hen finished, close the door to the back board and turn on the power. The LED will light up. See Pic. 26.
Pic. 26
If the LED does not light up, refer to Section 5: Trouble Shooting.
Step 2. Install dome drive
Set the DIP switches for SW1 and SW 2 on the bottom of the dome drive for the appropriate receiver address,
communication protocol, and baud rate. Refer to the labels on the dome drive or DIP SW ITCH SET in this manual.
Pic. 27
Line up link card and faucet of the back board of the dome. Push the dome drive in. See Pic. 27.
Step 3. Install dome flange
Snip a flake piece. Keep three flanges away from two clamps on the back board. See Pic. 28.
Pic. 28
Push the flange of dome into the back board. Take out the membrane on the clarity flake of the dome drive. See Pic. 29.
Pic. 29
3.2.4. POLE MOUNT INSTALLATION
See Section 3.2.1 W all Mount Installation.
12 / 43
4. OPERATION GUIDE
4.1. OPERATION AT POWER UP
The camera employs the default settings the first time it is switched on. Changes to the settings will be permanently
stored and will be made available the next time the camera is switched on. You can return to the default settings by
means of the appropriate menu option at any time.
The camera will work as follows when it is switched on.
The camera will run a calibration procedure and a message showing the following information will appear on the video
output OSD (On Screen Display): protocol, communication parameters, camera address and software version.
PROTOCOL: PELCO-D
COM: 9600, N, 8, 1
ADDR: 1
SOFTWARE VERSION V4.3.3
Check that the data are suitable for op eration. Otherwise, refer to the section in this document that shows how to install
the camera correctly.
At the end of the calibration step, the camera will switch to stand-by as programmed (POWER UP ACTION in DOME
SETTINGS1 > POWER UP). The camera will continue working this way until any command is received from the keypad.
The camera during this phase can be pointed to a fixed point or pan across the field. Refer to the detailed described in the
POWER UP ACTION menu section for more details.
4.2. HOW TO USE OUR CONTROL KEYBOARD
The camera is ready to receive commands from our control keyboard (see figure below) after connecting.
4.2.1. CONTROL KEYPAD PASSWORD AND ACCESS
The system will wait for the password to be entered after being switched on.
The control panel requires a 6-digit password.
The entered digits will be replaced by a “*” symbol on the screen for privacy.
Access to the menu is gained after entering all the digits correctly.
Refer to the corresponding manual for using the control panel.
The default user password is “000000”.
It is advisable to change the default password to prevent intrusions.
Do not lose or forget the programmed password.
Take note of the new password and keep it in a safe place.
4.2.2. CONTROL KEYPAD
Controls can use the joystick, single keys or key combinations. The key command syntax is shown below.
COMM
AND SYNTAX
zoom. If the option is ON, the maximum rotat
Key command syntax
The syntax used in this manual for controls using keys consists of various elements (words and three digit numbers).
Each command is always in braces and each element is separated by commas. Each word or decimal digit used in the
syntax is identified by a corresponding key on our control panel. Words can be enclosed in round brackets, square
brackets or no brackets. Three digit decimals are never enclosed in brackets.
The following words only can be used: CALL, ESC, OPEN, CLOSE, NEAR, FAR, ZOOM OUT, ZOOM IN, CAM, MON, SCAN, ENTER
The decimal digits are: 0, 1, 2, 3, 4, 5, 6, 7, 8,
and 9. Some application examples of controls are shown in detail below.
Using the joystick
A command can also be given simply by moving the joystick because this generates actions on the camera or OSD (On
Screen Display) menu.
Using a single key
Pressing a single key can cause camera action. For example, the following command will zoom out of the frame.
Underling indicates the key is in use.
ZOOM OUT
Key combinations
Pressing a key combination in rapid sequence extents the command set. For example, the foll owing command (select
camera address 1) is performed by pressing the following keys:
1 + CAM
4.2.3. CONTROL KEYPAD
There are four command types:
Select camera,
Move camera (tilt and pan, zoom, adjust focus and IRIS opening, go to preset positions),
Adjust camera operation mode using menus,
Various quick controls operable from the control panel.
The method for accessing these controls will be shown in detail in the following paragraphs.
4.3. SELECT A CAMERA
The camera to be controlled must be selected first. For example, the following command selects camera 1:
1 + CAM
After this operation, the message CAM 1 will appear on the control panel display.
4.4.
CAMERA
MOTIONS
After selecting a camera, it can be moved either directly using the control panel as described below:
Panning (horizontal) and tilting (vertical).
Zooming, focusing and IRIS opening.
Preset positions programming and recalling.
These functions can be directly accessed using a single key or joystick or a simple key combination.
4.4.1. PAN AND TILT
The camera may be moved using our keyboard controller. Move the joystick vertically to tilt the camera and horizontally to
pan it.
The maximum pan span is from 0º to 360º with continuous rotation. The maximum tilt span is from -5º (camera in vertical
position) and 92º.
The panning and tilting speed can be modulated by operating the joystick appropriately.
Note that the maximum speed that can be obtained by operating the joystick is not always equal to that programmed in
the working settings. This in fact depends on the value of the PROPORTIONAL PAN setting in the MOTION menu and the
COMM
AND TYPES
ion speed which can be obtained using the joystick is proportional to the
14 / 43
15 / 43
magnification used to obtain the best frame.
Panning (horizontal)
Tip the joystick rightwards to turn the camera horizontally clockwise and tip it leftwards to turn it anticlockwise.
If no advanced options are set (e.g. range limits set enabled), the camera can be turned continuously without
interruptions.
The pan span may be limited between two angles in DOME SETTING1 > MOTION > MANUAL LIMIT.
Tilting (vertical)
Tip the joystick upwards to turn the camera vertically upwards and tip it downwards to turn the camera downwards. The
camera rotation is limited upwards by the horizontal plane or downwards by the vertical axis.
Performance will change considerably near the vertical axis according to whether the AUTO FLIP is on or not (default
setting is on).
With AUTO FLIP off, the camera will stop in perfectly vertical position and will stop turning when the joystick is tipped
downwards.
With AUTO FLIP on, the camera will proceed over the vertical axis when the joystick is tipped do wnwards. This is
because, when the vertical axis is reached, the camera flips automatically by 180 degrees and resumes the initial
trajectory.
The AUTO FLIP function can be used to follow a subject arriving in a certain direction passes under the camera and
continues in a straight line. To do this, hold the joystick tipped downwards following the movement of the subject. Observe
that in this case the joystick performance after the camera passes over the vertical axis opposite to the normal axis
because tipping the joystick downwards will turn the camera upwards.
Normal operation of the joystick will be resumed as soon as the downward tip is interrupted (also only for an instant). At
this point, to follow the subject in the same direction, you will need to tip the joystick upwards, as you would normally.
4.4.2. ZOOM
The camera frame may be adjusted by using the ZOOM IN and ZOOM OUT commands. Use ZOOM IN to zoom
into the detail; use ZOOM OUT to zoom out.
Zoom can be set as per the zoom specifications of relative modules, combined between optical zoom and digital zoom.
Refer to the specific section for programming the function.
4.4.3. FOCUS
The camera focus may be adjusted manually using the NEAR and FAR controls.
As the auto focus function is always on, a manual setting made using NEAR and FAR will be kept only until a pan,
tilt or zoom command is used. In this case, auto focus will adjust focus automatically again.
Refer to the specific section for additional details on focusing and on the various options.
The auto focus function cannot work correctly in the following cases:
4.4.4. IRIS OPENING
The object to be focused on is not in the middle of the image.
There are far and near objects in the frame.
Bright light is shining on the subject.
The subject is behind a glass pane covered in drops or dust.
The subject is moving very quickly.
The subject is not well lit.
The subject is too big.
The IRIS opening may be controlled manually using the OPEN and CLOSE commands.
The manual setting made using OPEN and CLOSE will be kept only until a pan, tilt or zoom command is used if the
16 / 43
automatic IRIS opening option is enabled (the default setting is on). In this case, the opening will be controlling
automatically again.
Refer to the specific section for additional details on IRIS opening adjustment
4.4.5. PRESET
POSITIONS PROGRAMMING
AND RECALLING
The camera can store up to 256 panning, tilting and zooming configurations (called preset positions) which can be
recalled at any time. The manual focusing and IRIS opening settings cannot be stored.
When storing presets, it is important to remember that some are reserved and cannot be either stored or used for
positioning the camera. Presets from 80 to 99, Presets from 100 to 103, 170 to 173
The following examples show how to program the free Presets and recall them.
Example: programming preset number 32
1) Position the camera in a certain pan, tilt and zoom configuration.
2) Enter the command 32 + HOLD DOWN THE SHIFT KEY + 32.
From this moment on, simply enter the command 32 + CALL to move the camera to the preset position.
The saved value will be written over if the setting is reprogrammed.
The Presets are saved in a permanent memory area of the camera where they are maintained also when power
is disconnected. However, RESTORE FACTORY DEFAULT will delete all preset values.
Press 83 + CALL to delete all the saved presets.
The Presets store the coordinates according to an angular reference system. Therefore, the reference system
zero point may become misaligned with the camera mechanics after prolonged use of the tilting and panning
functions. Minor inaccuracies in preset positions may occur. In this case, calibrate the angular coordinate system
using the REBOOT SYSTEM command. This calibration is automatically run when the camera is switched on.
4.5. FUNCTION PROGRAM MENU
Use the following control panel command to access the function programming menu.
95 + CALL
At this point, if no password is required for access, the following first level menu will appear on the screen:
MAIN MENU
Otherwise, if a password is required, the following prompt will appear.
< SYSTEM INFORMATION >
< DISPLAY SETUP >
< DOME SETTINGS 1 >
< DOME SETTINGS 2 >
< DOME LABEL >
RESET CAMERA
REBOOT SYSTEM
LANGUAGE ENGLISH
EXIT
Screen 1: Main Menu
PLEASE INPUT PASSWORD
PASSWORD
1 2 3 4 5 6 7 8 9 0
▲
CLEAR
ENTER
EXIT
Screen 2: Password Protection
The password is a numeric combination (max. 4 digits).
17 / 43
Select the password digits by moving the joystick in the horizontal direction. Symbol “▲” indicates the digit which will be
Option
Value
Explanation
SYSTEM INFORMATION
Product information menu (refer to Section 4.5.1).
DISPLAY SETUP
Display menu (refer to Section 4.5.2).
DOME SETTINGS 1
Main programming menu (refer to Section 4.5.3).
DOME SETTINGS 2
Secondary programming menu (refer to Section 4.5.4).
DOME LABEL
Menu for associating the text to be associated to the camera (refer
to Section 4.5.5).
RESET CAMERA
This function reset the device without clearing the settings
performed by the user. Resets the camera menu settings, except
for the password.
REBOOT SYSTEM
This function restarts the device without clearing the settings
performed by the user. The camera is repositioned.
LANGUAGE
ENGLISH
Menus in English.
entered.
Press OPEN to enter the selected digit.
The entered numbers will be replaced by a “*” symbol on the screen for privacy.
Select ENTER and press OPEN to access the first level menu after entering all the digits correctly.
The default password is “0000”.
It is advisable to change the default password to prevent intrusions.
Do not lose or forget the programmed password.
Take note of the new password and keep it in a safe place.
Simply move the joystick vertically to scroll the menu and point the cursor to the menu item to be selected: at th is point,
select OPEN to access the selected second level.
Simply press BACK and use OPEN to go back to the previous level menu.
To completely exit a menu on any level, simply select EXIT and use the OPEN command.
4.5.1. PRODUCT
INFORM
Table 2
ATION
In the first level menu, select SYSTEM INFORMATION to display information concerning the protocol, the camera address,
the presetting number, the language of use and the measured temperature.
SYSTEM INFORMATION
COM 2400,N,8,1
ADDRESS 1
PROTOCOL PELCO-D
PRESETS 256
LANGUAGE ENGLISH
TEMPERATURE 36°C
SOFTWARE VERSION V4.3.3
BACK
EXIT
Screen 3: System Information
The information in this menu cannot be edited.
4.5.2. DISPLAY SETUP
The DISPLAY SETUP menu is used to enable the labels to be displayed for the various camera functions.
18 / 43
Option
Value
Explanation
PRESET LABEL
ON/OFF
Show or hide presetting labels (max. 64).
ZONE LABEL
ON/OFF
Show or hide zone labels.
ZOOM
ON/OFF
Show or hide zoom labels.
P/T DEG
ON/OFF
Show or hide camera pan/tilt degrees. The coordinates refer to the
monitor center.
DOME LABEL
ON/OFF
Show or hide dome labels.
LABEL POSITION
Label positioning submenu (refer to Section 4.5.2.1)
TEMPERATURE
ON/FF
Show or high the camera temperature.
DISPLAY SETUP
PRESET LABEL ON
ZONE LABEL ON
ZOOM ON
P/T DEG ON
DOME LABEL ON
<LABEL POSITION>
TEMPERATURE OFF
BACK
Screen 4: Display Menu
Table 3
4.5.2.1. LABEL POSITION
The labels may be positioned where required on the screen.
ZONE DOME PRESET
SAVE
P/T DEG ZOOM
RESET
Screen 5: Label Position
To establish a position:
1) Point the cursor to the label to be moved by moving the joystick vertically.
2) Press OPEN
3) Symbol “■” will appear.
4) Position the entire label in the chosen position using the joystick.
5) Press OPEN.
6) Repeat this operation for each label.
7) Point the cursor “►” to SAVE and press OPEN.
4.5.3. M AIN
PROGRAMMING
MENU (DOME
SETTINGS
1)
In the first level menu, select <DOME SETTINGS 1> and the corresponding submenus to access the main menus.
DOME SETTINGS1
<CAMERA>
<MOTION>
<POWER UP>
<PRESETS>
<PATTERNS>
<ZONES>
<CLEAR SET>
TOTAL PRESETS NUMBER 256
BACK
19 / 43
Option
Value
Explanation
CAMERA
Camera parameter programming submenu (refer to Section
4.5.3.1)
MOTION
Camera motion parameter programming submenu (refer to Section
POWER UP
Power up parameter submenu (refer to Section 4.5.3.3)
PRESETS
Preset parameter submenu (refer to Section 4.5.3.4)
PATTERNS
Pattern parameter submenu (refer to Section 4.5.3.5)
ZONES
Zone parameter programming submenu (refer to Section 4.5.3.6)
CLEAR SET
Clear settings submenu (refer to Section 4.5.3.7)
TOTAL PRESET NUMBER
40/64/256
Maximum number of Presets. Always enter 256 (refer to Section
Screen 6: Dome Settings 1
20 / 43
Option
Value
Explanation
DIGITAL ZOOM
ON/OFF
Switch digital zoom ON or OFF.
BACK LIGHT COMP
ON/OFF
Switch back light compensation ON and OFF. The BACK LIGHT
COMPENSATION function is useful for improving visibility when the
background light is very bright.
PROGRAM AE MODE
Automatic exposure submenu (see below)
ADDITIONAL
Additional settings submenu (see below).
WIDE DYNAMIC RANGE
ON/OFF
Activate W DR feature of the camera. This is only available on related
optical modules. This option is not supported by the any of 18X models.
Option
Value
Explanation
AE MODE
AUTO
In this mode:
- The shutter opening time cannot be set and is
automatically adjusted.
- Auto IRIS opening is automatically adjusted.
- Gain control is automatic (AGC ON).
Table 4
4.5.3.1. CAMERA For Veilux Model #'s VP-F18X, VP-AT18X, VP-ATDN18X, VP-ATDN36X, & VP-FDNC36X Only!
The first level of this menu contains the following options grouped as shown in the following table.
Please note that the camera menu below is for the following Veilux model #'s VP-F18X, VP-AT18X, VP-ATDN18X,
VP-ATDN36X, VP-FDNC36X.
To edit the value, simply select the required menu item using the joystick with vertical movements and the OPEN
button. Then edit as required. Select BACK/EXIT to close the item.
CAMERA
DIGITAL ZOOM OFF
BACKLIGHT COMP OFF
<PROGRAM AE MODE>
<ADDITIONAL>
WIDE DYNAMIC RANGE OFF
BACK
EXIT
Screen 7: Camera (Sub-Menu)
Table 5
PROGRAM AE CONTROL submenu - Automatic Exposure settings
PROGRAM AE CONTROL
AE MODE AUTO
LOW LIGHT MODE AUTO
LOW LIGHT LIMIT 1/50
IRIS LEVEL F2.0
AGC LEVEL 0DB
BRIGHT LEVEL 0DB/F2.0
SPOT AE OFF
BACK
EXIT
Screen 8: Program AE Control
21 / 43
SHUTTER
In this mode:
- The shutter opening time may be varied as programmed
in the “LOW LIGHT LIMIT” menu.
- Auto IRIS opening is automatically adjusted.
- Gain control is automatic (AGC ON).
IRIS
In this mode:
- The IRIS opening time is fixed to 1/50 second.
- The auto IRIS opening is manually varied in the “IRIS
LEVEL” menu.
- Gain control is automatic (AGC ON).
MANUAL
In this mode:
- The shutter opening time may be varied as programmed
in the “LOW LIGHT LIMIT” menu.
- The auto IRIS opening is manually varied in the “IRIS
LEVEL” menu.
- AGC gain control is variable as programmed in the “AGC
LEVEL” menu. All items may be accessed in this mode.
BRIGHT
In this mode:
- The IRIS opening time is fixed to 1/50 second.
- The auto IRIS opening is manually varied in the “BRIGHT
LEVEL” menu.
- Gain control is off (0 dB).
LOW LIGHT MODE
AUTO/MANUAL
This parameter is as follows:
- AUTO: uses a fixed maximum IRIS opening (1/50 second).
- MANUAL: increases camera sensitivity to the detriment of
refreshing frequency (frame rate) using the “LOW LIGHT
LIMIT” value.
These adjustments are possible only in “MANUAL” or
“SHUTTER” mode.
LOW LIGHT LIMIT
1/2, 1/3, 1/6, 1/12,
1/25, 1/50, 1/75,
1/100, 1/120, 1/150,
1/215, 1/300, 1/425,
1/600, 1/1000,
1/1250, 1/1750,
1/2500, 1/3500,
1/6000, 1/10000 OF
SECOND
This selects the maximum opening of the IRIS. It is used to
manually set the IRIS opening time.
These adjustments are possible only in “MANUAL” or
“SHUTTER” mode.
IRIS LEVEL
F2.0, F1.6, F1.4,
OFF, F22, F19, F16,
F14, F11, F 9.6,
F8.0, F6.8, F5.6,
F4.8, F4.0, F3.4,
F2.8, F2.4
Manual IRIS adjustment (parameter F).
It is used to manually set the IRIS opening time.
These adjustments are possible only in “MANUAL” or “IRIS”
mode.
AGC LEVEL
-3DB, 0DB, 2 DB, 4 DB,
6DB, 8 DB, 10 DB, 12
DB, 14 DB, 16 DB, 18
DB, 20 DB, 22 DB, 24
DB, 26 DB, 28 DB
It is possible to automatically control gain (AGC) to one of the
indicated values.
This selection is used to manually set the video signal gain.
These adjustments are possible only in “MANUAL” mode.
BRIGHT LEVEL
0DB ~ 28DB
This function adjusts the camera gain and the IRIS opening
using a special algorithm which may be programmed by the
user. Exposure is controlled by the gain in low light condition
and by the IRIS opening in bright light conditions.
The function may be used only if “AE MODE” is set to
“BRIGHT”.
SPOT AE
ON/OFF
If this function is on, the adjustments only use the middle part
of the image.
The following items cannot be accessed in if “AE MODE” is set to “AUTO”:
LOW LIGHT MODE (fixed to “MANUAL”)
Table 6
22 / 43
Option
Value
Explanation
IR SW MODE
AUTO/MANUAL
The opening and closing of the IR filter which adjusts the
Day & Night vision of the camera may be controlled in
MANUAL mode. The MANUAL option enables the possibility
to adjust the IR STATUS parameter (color, B/W ). In AUTO
mode, the switch is automatic according to the lighting.
IR STATUS
COLOR, B/W
Day & Night camera configuration.
AUTO IRIS
ON/OFF
The auto IRIS may operate automatically (ON) or at a
predetermined level in the “IRIS LEVEL” menu. If
enabled manually, this function will remain operative until
the camera performs an angular movement of less than
15 degrees. It will switch automatically.
SHARPNESS
ON/OFF
The sharpness of the image may be adjusted
automatically (ON) or to a level defined in the
“SHARPNESS LEVEL” menu.
SHARPNESS LEVEL
0 ~ 15
Sharpness can be programmed in the range from 1 to 15
(15 corresponds to maximum sharpness).
AUTO WHITE BALANCE
ATW
White Balance (W B) is performed in auto tracking mode
(Auto Tracking W hite). This mode automatically
balances the white level by analyzing a wide range of
colors, i.e. all those with temperatures comprised in the
range between 2000K and 10000K.
AUTO
This mode automatically adjusts the white balance by
analyzing a more restricted range with respect to the
previous option i.e. those with temperatures in the range
from 3000K and 7500K.
OUT
This function automatically balances the whites for
outdoor use.
IN
This function automatically balances the whites for indoor
use.
MAN
In this mode, white balancing may be performed by
manually selecting the amount of red (R GAIN) and blue
(B GAIN).
R GAIN
0 ~ 255
Adjust the red components using these values.
B GAIN
0 ~ 255
Adjust the blue components using these values.
LOW LIGHT LIMIT
IRIS LEVEL
AGC LEVEL
BRIGHT LEVEL
ADDITIONAL sub-menu - Other program settings.
ADDITIONAL
IR SW MODE AUTO IR
STATUS COLOR
AUTO IRIS ON
SHARPNESS ON
SHARPNESS LEVEL 5
AUTO WHITE BALANCE AUTO
R GAIN 214
B GAIN 164
BACK
Screen 9: Additional Sub-Menu
Table 7
23 / 43
The Following is the OSD of the camera menu only under Dome setting 1 for the Veilux 27X Module
24 / 43
25 / 43
26 / 43
27 / 43
28 / 43
29 / 43
30 / 43
31 / 43
32 / 43
33 / 43
34 / 43
35 / 43
4.5.3.2. MOTION
Option
Value
Explanation
AUTO FLIP
ON/OFF
When this option is on, the movements of a subject moving
underneath the camera can be followed by moving the
joystick vertically only. This is possible because after
reaching vertical position, the camera will automatically pan
by 180 degrees to be repositioned and resume the tilt stroke.
PROPORTIONAL PAN
ON/OFF
If this mode is active, the pan and tilt speed applied by the
keypad is proportional to the set zoom so that the movement
speed decreases when the zoom increases.
PARK TIME
15 S ~ 12 H
With this function, the camera will resume the function defined
in ”PARK ACTION” by specifying a value (in 1s, 1m, 1h steps)
following a stop or interruption of the performed function after
the programmed time.
PARK ACTION
NONE
No action is performed at the end of the park time.
AUTO SCAN
The camera performs an auto scan at the end of the park
time: the camera performs a 360 horizontal scan operation.
RANDOM SCAN
The camera performs a random scan at the end of the park
time: the camera performs a random 360 degree scan
pausing for approximately 2” every 142°.
FRAME SCAN
The camera performs a frame scan at the end of the park
time: the horizontal scan is performed in the
SET SCAN
limits.
PRESET 1/PRESET 8
The camera goes to preset 1 or preset 8 at the end of the park
time.
PATTERN 1 ~ 4
The camera performs one of the 4 patterns at the end of the
park time (command sequence continuously performed).
CRUISE
The camera performs a cruise (preset sequence) at the end of
the park time: the camera runs a cycle of up to 30 preset
positions.
REPEAT LAST
The camera simply resumes the operation it was performing
before being interrupted at the end of the park time.
HOME N TRA
The camera goes to preset 1 and starts tracking at the end of
the park time.
CRUISE TRA
The camera performs a cruise with tracking on at the end of
park time.
SCAN SPEED <DEG/S>
1 ~ 32 DEG./S
This will specify the rotation speed for automatic horizontal
scans.
SET SCAN
This submenu set the limits for horizontal pan movements of
the camera. The limits are long applicable in FRAME SCAN
mode (see below).
MANUAL LIMIT
ON/OFF
If this option is ON, horizontal automatically scanning is
performed within the right and left scanning limits open.
To set the left and right scanning limit, position the camera at
the required pan angle and press OPEN to set.
A preset position may be called up outside these scanning
limits.
SET AZIMUTH ZERO
This sets the pan zero position (see below).
CLEAR AZIMUTH ZERO
This is used to delete the zero position settings (see below).
MOTION
AUTO FLIP ON
PROPORTIONAL PAN ON
PARK TIME 15S
PARK ACTION NONE
SCAN SPEED<DEG/S> 1
<SET SCAN>
<MANUAL LIMIT>
<SET AZIMUTH ZERO>
<CLEAR AZIMUTH ZERO>
BACK
Screen 10: Motion Sub-Menu
36 / 43
Table 8
Option
Value
Explanation
POWER UP ACTION
NONE
No action is performed at the end of power up.
AUTO SCAN
The camera performs an auto scan at the end of power up: the
camera performs a 360 horizontal scan operation.
RANDOM SCAN
The camera performs a random scan at the end of power up:
the camera performs a random 360° scan pausing for
approximately 2” every 142°.
FRAME SCAN
The camera performs a frame scan at the end of power up:
the horizontal scan is performed in the SET SCAN limits.
PRESET 1/ PRESET 8
The camera goes to preset 1 or 8 at the end of power up.
PATTERN 1 ~ 4
The camera performs one of the 4 patterns at the end of
power up.
CRUISE
The camera performs a cruise at the end of power up: the
camera runs a cycle consisting of up to 30 preset positions.
HOME N TRA
The camera goes to preset 1 and starts tracking at the end of
power up.
CRUISE TRA
The camera performs a cruise with tracking on at the end of
power up.
SET SCAN submenu
This includes a number of settings related to the programming of horizontal FRAME SCAN limits.
1) Press “►” on “SET SCAN STOPS”.
2) Press OPEN to confirm.
3) Go to the required position with the joystick to set the left scanning limit.
4) Press OPEN to confirm.
5) Go to the required position with the joystick to set the right scanning limit.
6) Press OPEN to confirm, Press CLOSE to cancel the operation.
7) Point the cursor “►” to “CLEAR SCAN STOPS” and press OPEN to delete the programmed positions.
SET AZIMUTH ZERO submenu
This includes the settings related to programming of the pan zero position.
1) Go to the required position with the joystick to set zero position.
2) Press OPEN to confirm; Press CLOSE to cancel the operation.
CLEAR AZIMUTH ZERO submenu
This includes the settings related to deleting the pan zero position.
1) Press OPEN to confirm.
2) Press CLOSE to cancel the operation.
4.5.3.3. POWER UP
POWER UP
POWER UP ACTION NONE
BACK
EXIT
Screen 11: Power UP Sub-Menu
4.5.3.4. PRESETS
The camera will start a scanning cycle when a presetting or pattern is recalled. This scanning cycle may be
interrupted simply by moving the joystick.
Table 9
37 / 43
PRESETS
Option
Value
Explanation
PRESET NUMBER
1-64
This option is used to select a presetting for entering a
descriptive label. This operation is allowed for up to 64
presets.
Press the OPEN button and use the joystick to set the
number of the presetting to be stored. Press OPEN to
EDIT PRESET LABEL
This submenu is used to access writing mode for associating
a label to a presetting (see below).
EDIT PRESET POSITION
This submenu is used to position and save the current
position.
CLEAR CURRENT PRESET
The submenu is used to delete the current preset.
Option
Value
Explanation
PATTERN NUMBER
1 ~ 4
This option is used to select a pattern.
PROGRAM PATTERN
This submenu is used to program a pattern (see below)
CLEAR CURRENT PATTERN
This submenu is used to delete current pattern.
PRESET NUMBER 1
…PRESET NOT DEFINED…
<EDIT PRESET LABEL>
<EDIT PRESET POSITION>
<CLEAR CURRENT PRESET>
BACK
EXIT
Screen 12: Presets
Table 10
EDIT PRESET LABEL submenu
This includes the operations needed for associating a label to a presetting.
1) Use the joystick to point the cursor to ”EDIT PRESET LABEL” option.
2) Press OPEN. The following menu will appear on the display:
PRESET NUMBER 1
3) Point the cursor to the first character to use and press OPEN. Point the cursor to “BACKSPACE” to delete it.
4) After writing the text, point the cursor to OK and press OPEN to save and go back to the main screen.
4.5.3.5. PATTERNS
A pattern is a sequence of movements and functions which may be stored and repeated manually or automatically.
PRESET LABEL 1 - - - - 0 1 2 3 4 5 6 7 8 9 Y Z y z
A B C D E F G H I J K L M N O P Q R S T U V W X
a b c d e f g h I j k l m n o p q r s t u v w x
OK CANCEL
SPACE BACKSPACE`
Screen 13: Preset Label Sub-Menu
PATTERNS
PATTERN NUMBER 1
<PROGRAM PATTERN>
<CLEAR CURRENT PATTERN>
BACK
EXIT
Screen 14: Patterns Sub-Menu
PROGRAM PATTERN submenu
This includes all the operations needed to program a pattern.
1) Use the joystick to point the cursor to the ”PATTERN NUMBER” option.
Table 11
38 / 43
2) Select the required pattern and press OPEN.
Option
Value
Explanation
ZONE NUMBER
1 ~ 8
This option is used to select a zone.
Press the OPEN button and use the joystick to set
the required zone number. Press OPEN to confirm.
EDIT ZONE LABEL
This submenu is used to associate a label to a zone (see
below).
EDIT ZONE
This submenu is used to create a zone (see below).
ENABLE ZONE
ON/OFF
This is used to enable/disable each zone selected in the
“ZONE NUMBER” field.
CLEAR CURRENT ZONE
This submenu is used to delete the zone selected in the “ZONE
NUMBER” field (see below).
3) Position the cursor under ”PROGRAM PATTERN” option and press the OPEN button.
The number of actions available (including zoom operations) for programming the Pattern is shown in percentage form on
the screen while they are each being programmed. 100 operations are available for each pattern.
4.5.3.6. ZONES
ZONES
ZONE NUMBER 1
…ZONE NOT DEFINED…
<EDIT ZONE LABEL>
<EDIT ZONE>
ENABLE ZONE ON
<CLEAR CURRENT ZONE >
BACK
EXIT
Screen 15: ZONES Sub-Menu
A zone is a space defined on the display by the user. It may be associated to a label. Up to 8 zones may be defined.
Table 12
EDIT ZONE LABEL submenu
This includes the operations needed to enter labels to be associated to zones.
1) Use the joystick to point the cursor to the ”EDIT ZONE LABEL” option.
2) Press OPEN. The following menu will appear on the display:
ZONE NUMBER 1
3) Point the cursor to the first character to be used and press OPEN. Point the cursor to “BACKSPACE” to delete it.
4) After writing the text, point the cursor to OK and press OPEN to save and go back to the main screen.
EDIT ZONE submenu
This includes all the operations needed to program a zone.
1) Press “►” on “EDIT ZONE”.
2) Press OPEN to confirm.
3) Use the joystick to point to the required position to define the left limit of the zone to be created.
4) Press OPEN to confirm. Press CLOSE to cancel the operation.
5) Use the joystick to point to the required position to define the right limit of the zone to be created.
6) Press OPEN to confirm. Press CLOSE to cancel the operation.
7) Press CLOSE to cancel the operation.
4.5.3.7. CLEAR SET
ZONE LABEL 1 - - - - 0 1 2 3 4 5 6 7 8 9 Y Z y z
A B C D E F G H I J K L M N O P Q R S T U V W X
a b c d e f g h I j k l m n o p q r s t u v w x
OK CANCEL
SPACE BACKSPACE
Screen 16: Zone Label Sub-Menu
39 / 43
CLEAR SET
Option
Value
Explanation
CLEAR ZONES
This option is used to delete all the zone settings.
CLEAR PRESETS
This is used to delete all the Presets.
CLEAR PATTERNS
This is used to delete all the pattern settings.
RESTORE FACTORY
DEFAULT
This performs a total reset and loads the default settings. The
operations may take a few seconds (approximately 20
seconds): the message “WAIT” will appear on the monitor.
Option
Value
Explanation
ALARMS
Alarm submenu (refer to Section 4.5.4.1)
ADDR SETTING
Address setting submenu (refer to Section 4.5.4.2)
PASSWORD
Password submenu (refer to Section 4.5.4.3)
WINDOWS BLANKING
Windows blanking submenu (refer to Section 4.5.4.4)
HEATER SETTING
Heater use submenu (refer to Section 4.5.4.5)
CRUISE SETTING
Cruise programming submenu (refer to Section 4.5.4.6)
TRACKING SETTING
Automatic tracking submenu (refer to Section 4.5.4.7)
CLEAR ZONES
CLEAR PRESETS
CLEAR PATTERNS
RESTORE FACTORY DEFAULT
BACK
EXIT
Screen 17: Clear Set Sub-Menu
This menu is used to delete the settings of several elements at one time.
Table 13
4.5.3.8. PRESET NUMBER
This option can be used to set the number of Presets which may be used.
1) Point the cursor to “►” “PRESET NUMBER”.
2) Press ENTER.
3) Move the joystick vertically and select “256”.
4) Press ENTER to confirm.
Do not change the setting (“256”).
4.5.4. SECONDARY
In the first level menu, select <DOME SETTINGS 2> and the corresponding submenus to access the other menus.
PROGRAM MING
<ALARMS>
<ADDR SETTING>
<PASSWORD>
<WINDOWS BLANKING>
<HEATER SETTING>
<CRUISE SETTING>
<TRACKING SETTING>
BACK
EXIT
MENU (DOME SETTINGS 2)
DOME SETTINGS 2
Screen 18: Dome Settings 2
4.5.4.1. ALARMS
Table 14
40 / 43
ALARMS
Option
Value
Explanation
ALARM NUMBER
1 ~ 4
This option allows selecting one of the 4 alarm inputs.
SEQUENCE (SECS)
1 ~ 250
Duration time (in seconds) of the action related to each alarm
when several alarms occur at the same time.
ALARM ACT
NONE
No action is performed on alarm.
AUTO SCAN
The camera performs an auto scan on alarm: the camera
performs a 360 horizontal scan operation.
RANDOM SCAN
The camera performs a random scan on alarm: the camera
performs a random 360° scan pausing for approximately 2” every
142°.
FRAME SCAN
The camera performs a frame scan on alarm: the horizontal scan
is performed in the SET SCAN limits.
PRESET
The camera goes to related preset on alarm.
PATTERN 1
The camera performs pattern action 1 on alarm.
PATTERN 2
The camera performs pattern action 2 on alarm.
PATTERN 3
The camera performs pattern action 3 on alarm.
PATTERN 4
The camera performs pattern action 4 on alarm.
CRUISE
The camera performs a cruise on alarm: the camera runs a cycle
consisting of up to 30 preset positions.
TRACKING
The camera performs tracking action on alarm.
PRESET N TRA
The camera goes to related preset and starts tracking function.
CRUISE TRA
The camera performs a cruise with tracking on alarm.
ACTIVATE AUX
OFF
No action occurs after the alarm.
1
Output 1 is on.
2
Output 2 is on.
CLEAR SETTINGS
This submenu is used to delete the alarm programming (see
below).
DWELL TIME<SECS>1
0 ~ 255
The duration of related alarm output
DWELL TIME<SECS>2
0 ~ 255
The duration of related alarm output
ALARM NUMBER 1
SEQUENCE(SECS) 1
ALARM ACT CRUISE
ACTIVATE AUX OFF
<CLEAR SET>
DWELL TIME<SECS>1 0
DWELL TIME<SECS>2 0
BACK
EXIT
Screen 19: Alarms Sub-Menu
The camera has 4 alarm inputs and 2 alarm outputs. The actions defined by the user may be associated to an alarm.
If an alarm is triggered during any automatic operation of the camera (Pattern, Auto Tracking, etc.), the operation
in progress is stopped and the camera executes the action that has been set in the ALARM ACT menu:
In the event of Preset action, the camera moves to the preset position. Then, if the option PARK ACTION is
set to execute an action, the action will be executed after the PARK TIME period has expired.
In the event of "PATTERN, AUTO SCAN, RANDOM SCAN, FRAME SCAN, CRUISE" actions, the action is
executed by the camera permanently and can only be stopped by one of the following actions: any
command sent by a controller or any alarm event.
4.5.4.2. ADDR SETTING
Table 15
41 / 43
ADDR SETTING
Option
Value
Explanation
ADDR TYPE
SOFT, HARD
This option is used to program the type of address in current
application.
Press the OPEN button and use the joystick to select the
value. Press OPEN to confirm.
ADDR SOFT
0~255
The option is used to change the soft address.
ADDR HARD
This option shows the hard address number. It is the address
of the SW 2 (Switch Setting 2).
Option
Value
Explanation
ENABLE PASSWORD
ON/OFF
This enables the password.
EDIT PASSWORD
This is the password entry procedure.
ADDR TYPE HARD
ADDR SOFT 255
ADDR HARD 0
BACK
EXIT
Screen 20: Alarm Settings
The soft address is the address programmed by built-in software. The hard address is the address programmed by the
hardware SW ITCH 2.
Table 16
The camera needs a reboot for the new address to take effect. When the hard address is different from that of
last power up, the hard address will be applicable and the camera address will be hard type.
4.5.4.3. PASSWORD
ENABLE PASSWORD OFF
<EDIT PASSWORD>
BACK
EXIT
Screen 21: Password Sub-Menu
PASSWORD
The password is a numeric combination (max. 10 digits).
The default password is “0000”.
It is advisable to change the default password to prevent intrusions.
Do not lose or forget the programmed password.
Take note of the new password and keep it in a safe place.
PASSWORD
1 2 3 4 5 6 7 8 9 0
1) Select the password digits by moving the joystick in the horizontal direction. Symbol “▲” indicates the digit which will
be entered.
2) Press OPEN to enter the selected digit.
3) The entered numbers will be replaced by a “*” symbol on the screen for privacy.
CLEAR
ENTER
BACK
Table 17
INPUT OLD PASSWORD
Screen 22: Edit Password
42 / 43
4) Enter all the digits correctly and select CALL to
Option
Value
Explanation
STYLE
GRAY/SMEAR
There are two ways to blank out the zone to be masked: either
using a grey window which entirely conceals the area or by
using a semi-transparent smear window which shows the scene
without details.
BLANK ALL ABOVE
OFF, 0~80
Blanks out the upper part of the frame shown on the monitor.
The value means the beginning degree of the vertical position.
BLANK ALL BELOW
OFF, 0~80
Blanks out the lower part of the frame shown on the monitor. The
value means the beginning degree of the vertical position.
SET WINDOWS
The submenu is used to position and configure the privacy
zones (see below).
SET MASK COLOR
0 ~ 13
This is used to select the blanking window color:
0 → black
1 ~ 6 → grey (1 dark; 6 light)
7 → white
8 → red
9 → green
10 → blue
11 → cyan
12 → yellow
13 → magenta
BLANK ALL ABOVE
BLANK ALL BELOW
OFF
No blanking
OFF
No blanking
0
-5º~10º
0
5º~92º
10
-5º~25º
10
-5º~92º
20
-5º~35º
20
5º~92º
confirm.
5) During the password change procedure you will be
asked to enter the ol d password. Enter the new password and
enter it again for confirmation.
4.5.4.4. WINDOWS BLANKING
Windows blanking is only available for the following Veilux model #'s VP-F18X, VP-AT18X, VP-ATDN18X, VP-
ATDN36X, VP-FDNC36X.
The camera can be used to define up to eight privacy zones which blank out certain areas of the screen concealing them
from the operator’s sight.
A privacy zone appears as a grey or black rectangle associated to a certain pan, tilt and zoom position of a camera. This
association is used to move, expand and compress the rectangle according to how the pan, tilt or zoom settings are
changed.
WINDOWS BLANKING
STYLE GRAY
BLANK ALL ABOVE OFF
BLANK ALL BELOW OFF
<SET WINDOWS>
SET MASK COLOR 4
BACK
EXIT
Screen 23: Windows Blanking
The two blanking bands (upper & lower) may coexist at the same time.
The two blanking bands (upper & lower) cannot coexist at the same time in presence of a privacy zone.
A band will automatically be removed if both bands are enabled and a privacy zone is activated.
If an attempt to activate a blanking band is attempted with a privacy zone active, the p rivacy zon e will remain
active to the detriment of the blank.
Blanking parameters
Table 18
43 / 43
30
-5º~45º
30
15º~92º
40
-5º~55º
40
25º~92º
50
-5º~65º
50
35º~92º
60
-5º~75º
60
45º~92º
70
-5º~85º
70
55º~92º
80
-5º~95º
80
70º~92º
Option
Value
Explanation
WINDOWS NUMBER
1~ 8
This option is used to select one of the 8 privacy zones
(WINDOWS).
EDIT WINDOW LOCATION
This option is used to activate the privacy zone positioning
procedure (see below).
EDIT WINDOW ZOOM
This option sets the zoom level over which the created privacy
zone will be visible.
ENABLE WINDOW
ON/OFF
This switches the privacy zone selected in WINDOW NUMBER on
and off.
CLEAR CURRENT WINDOW
This deletes the privacy zone selected in WINDOW NUMBER.
Table 19
The coordinates shown on the monitor refer to the central point of the monitor (where the diagonals meet).
SET WINDOWS submenu
This includes the operations needed to position and configure the privacy zones.
SET WINDOWS
WINDOWS NUMBER 1
<EDIT WINDOW LOCATION>
<EDIT WINDOW ZOOM >
ENABLE WINDOW OFF
CLEAR CURRENT WINDOW
BACK
EXIT
Screen 24: Set Windows Sub-Menu
Table 20
EDIT WINDOW LOCATION submenu
This menu may be used to define the position of the privacy zones to be created.
1) Press “►” on “EDIT WINDOW LOCATION”.
2) Press OPEN. The following screen will appear.
EDIT WINDOW LOCATION
IRIS OPEN TO CONTINUE
IRIS CLOSE TO CANCEL
Screen 25: Edit Window Location Sub-Menu
3) A cross-shaped pointer will appear on the monitor: this pointer will correspond to the middle of the privacy zones
being created.
4) Point the cross-shaped cursor to the required position by moving the joystick in the vertical and horizontal directions.
5) Press OPEN. A square will appear on the monitor (with the previously defined features).
6) Use the joystick to obtain the required dimensions of the privacy zone:
a) Move leftwards to increase the left and right edges of the blanking zone
b) Move rightwards to decrease the left and right edges of the blanking zone
c) Move upwards to increase the upper and lower edges of the blanking zone
d) Move downwards to decrease the upper and lower edges of the blanking zone
7) Press OPEN to confirm after reaching the required dimensions.
8) At this point, either select a new privacy zone or select CLOSE to quit the menu.
It is preferable to set the privacy zones with a zoom level of 1x.
Remarks on Privacy Zones
44 / 43
Privacy zones can be programmed (and therefore the menu can be opened) in optical zoom
Option
Value
Explanation
HEATER DISPLAY
ON/OFF
This switches the heater status display on and off. The
message “HEATER” will appear when the heater is on.
HEATER MODE
AUTO
Heater operating mode: when set to ”AUTO”, the heater is
operated when the outside temperature is lower than the
setting made in the following menu.
OFF
The heater is always off.
ON
The heater is always on.
TEMPERATURE SET
-99 ~ +99
Temperature threshold in °C under which the heater is
activated. Recommended values 18 - 20 °C
situations only. The privacy zone works also in digital zoom conditions.
The privacy zone rectangle will move on the screen when panning and tilting. Zooming will expand
and contract the rectangle.
The rectangle will expand twice in the vertical direction and four times in the horizontal position to
avoid viewing protected areas when panning, tilting and zooming.
After panning and tilting, the privacy zone rectangle will shift and return to the correct dimensions.
After zooming, the rectangle will remain either contracted or expanded according to the applied zoom
(regardless of the x2 or x4 factor applied while zooming).
It is advisable to make the privacy areas slightly larger than the area to be concealed.
Privacy zones can only be rectangular or squares, but several rectangles can be placed to mask the
area as required.
EDIT WINDOW ZOOM submenu
This menu item is used to define the zoom level at which the privacy zone becomes visible after defining the color and the
position of the privacy zone.
1) Press “►” on “EDIT WINDOW ZOOM”.
2) Press OPEN, the following screen will appear.
EDIT WINDOW ZOOM
3) Press OPEN and start the zoom setting procedure. The newly created privacy zone will appear on the monitor.
4) Use the joystick to obtain the required zoom level over which the privacy zone will become visible:
a) Turn clockwise to increase the zoom level
b) Turn anticlockwise to decrease the zoom level
5) Press OPEN to confirm.
4.5.4.5. HEATER SETTING
IRIS OPEN TO CONTINUE
IRIS CLOSE TO CANCEL
Screen 26: Edit Window Zoom
HEATER SETTING
HEATER DISPLAY ON
HEATER MODE AUTO
TEMPERATURE SET 33℃
BACK
EXIT
Screen 27: Heater Setting
4.5.4.6. CRUISE SETTING
Table 21
45 / 43
CRUISE
Option
Value
Explanation
DWELL TIME <SECS>
5 ~ 250
Duration (in seconds) of the dwelling time on each presetting.
PRESET LIST
1 ~ 3
Value 1 selects the first group of Presets from 1 to 10, value 2
selects the second group from 11 to 20, value 3 the third
group from 21 to 30.
The following 10 digits (1/10) are used to switch the
corresponding preset in the corresponding ten (1-10, 11-20,
21-30) either on or off (1=ON; 0=OFF).
Option
Value
Explanation
DEFAULT SETTING
This function is used to load the auto tracking default
settings.
SIZE SENS
LARGE/MEDIUM/SMAL
L
This option defines the total dimensions of the object to be
tracked. The pa rameters are LARGE/MEDIUM/SMALL. An
object larger than one fourth of the screen is LARGE. An
object smaller than one eighth of the screen is SMALL.
GRAY SENS
HIGH/MEDIUM/LOW
This option determines the auto tracking sensitivity. The
sensitivity measures the grey scale variations of a certain
point in the frame in the unit of time.
LOST ACT
HOME N TRA
This option is used to establish the action to be performed
if the camera loses the tracked object: the HOME N TRA
option goes to preset 1 and starts tracking.
KEEP TRACK
The KEEP TRACK option keeps the camera in the position
reached and the tracking function is kept on waiting for an
object to be intercepted again.
STOP TRACK
The STOP TRACK option leaves the camera in the position
reached and deactivates the tracking function.
DWELL TIME<SECS> 7
PRESET LIST 1
1 ON 0 OFF
1234567890 <PRESET 1-10>
0110010111
BACK
EXIT
Screen 28: Cruise
The CRUISE function is used to make the camera run a cycle consisting of up to 30 preset positions.
This menu item is used to enable each of the preset positions used in the cruise cycle.
For the cruise cycle to be effective, the preset positions must be actually stored.
4.5.4.7. TRACKING SETTING
Table 22
TRACKING SETTING
DEFAULT SETTING
SIZE SENS MEDIUM
GRAY SENS MEDIUM
LOST ACT STOP TRACK
ZOOM SETTING ON
WAIT TIME<S> 40
<TRACKING BOUNDARY>
AUX OFF
TRACKING SPEED
TRACKING TIME<M> AUTO
BACK
Screen 29: Tracking Setting Sub-Menu
AUTO
The auto tracking function is used to automatically track moving objects by detecting gray scale variations in the frame.
46 / 43
ZOOM SETTING
OFF, 1 ~ 18
This option determines the maximum zoom value that the
camera may use for tracking the object.
WAIT TIME
5, 10, 15, 20, 25,
30, 35, 40 SECONDS
This option determines the time which must elapse before
performing Lost Act after losing a motion in frame.
TRACKING BOUNDARY
UP/DOWN/LEFT/RIGH
T
This option is used to define the zone in which the camera
performs the tracking.
AUX OFF, 1, 2
This option is used to activate one of the 2 alarm outputs if
the tracking function is on (OFF = no active alarm output).
TRACKING SPEED
AUTO, 1 ~ 63
This option establishes the camera movement speed. If
AUTO is selected, the camera is automatically “adapted” to
the motion of the target. The 1~63 options allow selecting
the expected speed of the object to be tracked (1 slow, 63
fast).
TRACKING TIME
AUTO,1~15
(MINUTES)
This option allows setting the max. tracking duration, in
minutes, during which the camera automatically tracks
moving objects.
Once the tracking time has expired, the camera exits the
tracking mode, waiting for further commands
Option
Value
Explanation
BOUNDARY LIMIT
ON/OFF
This switches tracking function intervention zone on and off.
CLEAR BOUNDARY
This deletes the intervention area.
LEFT LIMIT
ON/OFF
Left limit of the intervention zone.
RIGHT LIMIT
ON/OFF
Right limit of the intervention zone.
UP LIMIT
ON/OFF
Up limit of the intervention zone.
DOWN LIMIT
ON/OFF
Low limit of the intervention zone.
Table 23
TRACKING BOUNDARY submenu
Operations needed to establish an intervention zone for the tracking function.
TRACKING BOUNDARY
BOUNDARY LIMIT OFF
CLEAR BOUNDARY
LEFT LIMIT OFF
RIGHT LIMIT OFF
UP LIMIT OFF
DOWN LIMIT OFF
BACK
EXIT
Screen 30: Tracking Boundary Sub-Menu
Advice for Correct Auto Tracking Use
Table 24
47 / 43
General warnings
Option
Value
Explanation
EDIT DOME LABEL
This submenu is used to access writing mode for associating
a camera label (see below).
The tracking function should mainly be used in indoor environments.
Provide the best lighting possible in the detection zone: in poor lighting conditions, the inevitable
presence of noise on the image makes gray scale variations extremely critical. In poor lighting
conditions, the camera may easily lose the tracked object.
If IR illuminators are used, remember that:
The camera must be programmed to operate in B/W only (DOME SETTINGS 1 > CAMERA >
ADDITIONAL menu) because the Slow Shutter will make tracking unreliable in color mode
The lighting entirely covers the frame where motion is tracked, possibly by restricting the range of
action of the camera in tracking mode (using the TRACKING BOUNDARY option).
Avoid background objects in the frame which could trick the motion detector, such as for example
Venetian blinds, gates, doors with grid and objects with very marked, contrasting contours. A
checkerboard background is certainly the worst condition for satisfactory operation.
Do not use the privacy zone function in frames where auto tracking is used: the privacy zone can trick
the auto tracking function.
Do not use the auto tracking function if the object to be tracked and/or monitored moves too fast.
Recommended control parameters
SIZE SENS: select SMALL particularly in poor lighting conditions to improve performance.
GRAY SENS: most false alarms are caused by the tracking of unexpected objects. For this reason, it is
preferable to select low sensitivity.
ZOOM SETTING: it is advisable to use the lowest possible zoom values.
WAIT TIME: particularly, in the case of poor lighting conditions or frames with interference, it is preferable to
set the lowest possible time to prevent the camera from constantly tracking unexpected objects (e.g. “video
noise” in the frame).
TRACKING SPEED: the AUTO setting should always be preferred, unless the object to be tracked does not
always move at low, constant speed.
TRACKING BOUNDARY: it is strongly advised to delimit the tracking zone, avoiding including unnecessary
parts in the frame.
Tracking during cruise is available. When the camera is cruising among saved presets, it will detect and follow
moving object automatically when it stops at a specific preset. When the moving object gets out of view for
pre-defined interval, the camera will go back to its previously stopped preset and cruise to the next preset again.
Enter DOME SETTINGS 1 > MOTION > PARK ACTION, set it as REPEAT LAST
Go to DOME SETTINGS 2 > TRACKING SETTING > LOST ACT, set it as STOP TRACK
Go to DOME SETTINGS 2 > CRUISE > DWELL TIME, set it as 8 and program the preset list
92 + CALL to start the function.
4.5.5. DOME LABEL
DOME LABEL
<EDIT DOME LABEL>
<CLEAR DOME LABEL>
BACK
EXIT
Screen 31: Dome Label Menu
48 / 43
Control panel command
Function
95 + Call
Access main menu
XXX + Call
Recall preset position (Preset) xxx.
80 + Call
Start the tracking function
82 + Call
Start the cruise function
83 + Call
Delete all Presets
84 + Call
Start pattern 1
85 + Call
Start pattern 2
86 + Call
Start pattern 3
87 + Call
Start pattern 4
88 + Call
Start park action function
89 + Call
Stop park action function
92 + Call
Start cruise with tracking function activated
93 + Call
Call the menu of boundary setting
94 + Call
Start/Stop wide dynamic range function
97 + Call
Start random scan function
98 + Call
Start frame scan function
99 + Call
Start auto scan function
CLEAR DOME LABEL
This submenu allows deleting the label associated to the
camera (see below).
Table 25
EDIT DOME LABEL submenu
The operations needed to associate a label to a camera are:
1) Use the joystick to point the cursor to the ”EDIT DOME LABEL” option.
2) Press OPEN. The following menu will appear on the display:
DOME LABEL
0 1 2 3 4 5 6 7 8 9 Y Z y z
A B C D E F G H I J K L M N O P Q R S T U V W X
a b c d e f g h I j k l m n o p q r s t u v w x
OK CANCEL
SPACE
3) Point the cursor to the first character to be used and press OPEN. Point the cursor to “BACKSPACE” to delete it.
4) After writing the text, point the cursor to OK and press OPEN to save and go back to the main screen.
4.6. SPECIAL CONTROL PANEL
COMM
EDIT DOME LABEL
BACKSPACE
Screen 32: Edit Dome Label
ANDS
The camera can be programmed and operated using various quick control panel commands.
When storing Presets, it is important to remember that some are reserved and cannot be either stored or used for
positioning the camera. Presets from 80 to 99, Presets from 100 to 103, 170 to 173.
Table 26
49 / 43
5. TROUBLE SHOOTING
Problem
Possible Reason
Solution
Power on normally but no video
signal
Wrong wire connections
Check and reconnect wires
Wrong or bad power source
Change power source
Fuse broken.
Change fuse
Power cable is disconnected
Reconnect power wiring
Pan/Tilt not initializing when
power on
Address, protocol, and baud rate is not
correctly set
Check and set the parameters
again.
RS485 cable is not correctly connected
Check and reconnect RS485 cable
Video is not stable
Video cable is wrong
Check and reconnect video
Power source is wrong
Change the power source
Control center is not stable
RS485 wiring error
Check and reconnect the RS485
Table 27
50 / 43
6. ANNEX
POS
1 2 3 4 DESCRIPTION
COMM
PTOL
ON
OFF
OFF
OFF
USER
OFF
ON
OFF
OFF
PELCO-P
ON
ON
OFF
OFF
PELCO-D
POS
DESCRIPTION
5 6 7
8
BAUD
RATE
(BPS)
1200
ON
OFF
OFF
OFF
2400
OFF
ON
OFF
OFF
4800
ON
ON
OFF
OFF
9600
OFF
OFF
ON
OFF
19200
ON
OFF
ON
OFF
Reserved for future use
…
ADDRESS
1 2 3 4 5 6 7
8
0
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
1
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
4
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
5
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
6
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
7
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
8
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
9
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
10
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
11
ON
ON
OFF
ON
OFF
OFF
OFF
OFF
12
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
13
ON
OFF
ON
ON
OFF
OFF
OFF
OFF
14
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
15
ON
ON
ON
ON
OFF
OFF
OFF
OFF
16
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
17
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
18
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
19
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
20
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
21
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
22
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
23
ON
ON
ON
OFF
ON
OFF
OFF
OFF
24
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
25
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
26
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
27
ON
ON
OFF
ON
ON
OFF
OFF
OFF
28
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
29
ON
OFF
ON
ON
ON
OFF
OFF
OFF
30
OFF
ON
ON
ON
ON
OFF
OFF
OFF
31
ON
ON
ON
ON
ON
OFF
OFF
OFF
32
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
6.1. DIP SWITCH CHART
Table 28: SWITCH1 SETTING
51 / 43
33
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
34
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
35
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
36
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
37
ON
OFF
ON
OFF
OFF
ON
OFF
OFF
38
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
39
ON
ON
ON
OFF
OFF
ON
OFF
OFF
40
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
41
ON
OFF
OFF
ON
OFF
ON
OFF
OFF
42
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
43
ON
ON
OFF
ON
OFF
ON
OFF
OFF
44
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
45
ON
OFF
ON
ON
OFF
ON
OFF
OFF
46
OFF
ON
ON
ON
OFF
ON
OFF
OFF
47
ON
ON
ON
ON
OFF
ON
OFF
OFF
48
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
49
ON
OFF
OFF
OFF
ON
ON
OFF
OFF
50
OFF
ON
OFF
OFF
ON
ON
OFF
OFF
51
ON
ON
OFF
OFF
ON
ON
OFF
OFF
52
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
53
ON
OFF
ON
OFF
ON
ON
OFF
OFF
54
OFF
ON
ON
OFF
ON
ON
OFF
OFF
55
ON
ON
ON
OFF
ON
ON
OFF
OFF
56
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
57
ON
OFF
OFF
ON
ON
ON
OFF
OFF
58
OFF
ON
OFF
ON
ON
ON
OFF
OFF
59
ON
ON
OFF
ON
ON
ON
OFF
OFF
60
OFF
OFF
ON
ON
ON
ON
OFF
OFF
61
ON
OFF
ON
ON
ON
ON
OFF
OFF
62
OFF
ON
ON
ON
ON
ON
OFF
OFF
63
ON
ON
ON
ON
ON
ON
OFF
OFF
64
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
65
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
66
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
67
ON
ON
OFF
OFF
OFF
OFF
ON
OFF
68
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
69
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
70
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
71
ON
ON
ON
OFF
OFF
OFF
ON
OFF
72
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
73
ON
OFF
OFF
ON
OFF
OFF
ON
OFF
74
OFF
ON
OFF
ON
OFF
OFF
ON
OFF
75
ON
ON
OFF
ON
OFF
OFF
ON
OFF
76
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
77
ON
OFF
ON
ON
OFF
OFF
ON
OFF
78
OFF
ON
ON
ON
OFF
OFF
ON
OFF
79
ON
ON
ON
ON
OFF
OFF
ON
OFF
80
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
81
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
82
OFF
ON
OFF
OFF
ON
OFF
ON
OFF
83
ON
ON
OFF
OFF
ON
OFF
ON
OFF
52 / 43
84
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
85
ON
OFF
ON
OFF
ON
OFF
ON
OFF
86
OFF
ON
ON
OFF
ON
OFF
ON
OFF
87
ON
ON
ON
OFF
ON
OFF
ON
OFF
88
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
89
ON
OFF
OFF
ON
ON
OFF
ON
OFF
90
OFF
ON
OFF
ON
ON
OFF
ON
OFF
91
ON
ON
OFF
ON
ON
OFF
ON
OFF
92
OFF
OFF
ON
ON
ON
OFF
ON
OFF
93
ON
OFF
ON
ON
ON
OFF
ON
OFF
94
OFF
ON
ON
ON
ON
OFF
ON
OFF
95
ON
ON
ON
ON
ON
OFF
ON
OFF
96
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
97
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
98
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
99
ON
ON
OFF
OFF
OFF
ON
ON
OFF
100
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
101
ON
OFF
ON
OFF
OFF
ON
ON
OFF
102
OFF
ON
ON
OFF
OFF
ON
ON
OFF
103
ON
ON
ON
OFF
OFF
ON
ON
OFF
104
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
105
ON
OFF
OFF
ON
OFF
ON
ON
OFF
106
OFF
ON
OFF
ON
OFF
ON
ON
OFF
107
ON
ON
OFF
ON
OFF
ON
ON
OFF
108
OFF
OFF
ON
ON
OFF
ON
ON
OFF
109
ON
OFF
ON
ON
OFF
ON
ON
OFF
110
OFF
ON
ON
ON
OFF
ON
ON
OFF
111
ON
ON
ON
ON
OFF
ON
ON
OFF
112
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
113
ON
OFF
OFF
OFF
ON
ON
ON
OFF
114
OFF
ON
OFF
OFF
ON
ON
ON
OFF
115
ON
ON
OFF
OFF
ON
ON
ON
OFF
116
OFF
OFF
ON
OFF
ON
ON
ON
OFF
117
ON
OFF
ON
OFF
ON
ON
ON
OFF
118
OFF
ON
ON
OFF
ON
ON
ON
OFF
119
ON
ON
ON
OFF
ON
ON
ON
OFF
120
OFF
OFF
OFF
ON
ON
ON
ON
OFF
121
ON
OFF
OFF
ON
ON
ON
ON
OFF
122
OFF
ON
OFF
ON
ON
ON
ON
OFF
123
ON
ON
OFF
ON
ON
ON
ON
OFF
124
OFF
OFF
ON
ON
ON
ON
ON
OFF
125
ON
OFF
ON
ON
ON
ON
ON
OFF
126
OFF
ON
ON
ON
ON
ON
ON
OFF
127
ON
ON
ON
ON
ON
ON
ON
OFF
128
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
129
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
130
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
131
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
132
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
133
ON
OFF
ON
OFF
OFF
OFF
OFF
ON
134
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
53 / 43
135
ON
ON
ON
OFF
OFF
OFF
OFF
ON
136
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
137
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
138
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
139
ON
ON
OFF
ON
OFF
OFF
OFF
ON
140
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
141
ON
OFF
ON
ON
OFF
OFF
OFF
ON
142
OFF
ON
ON
ON
OFF
OFF
OFF
ON
143
ON
ON
ON
ON
OFF
OFF
OFF
ON
144
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
145
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
146
OFF
ON
OFF
OFF
ON
OFF
OFF
ON
147
ON
ON
OFF
OFF
ON
OFF
OFF
ON
148
OFF
OFF
ON
OFF
ON
OFF
OFF
ON
149
ON
OFF
ON
OFF
ON
OFF
OFF
ON
150
OFF
ON
ON
OFF
ON
OFF
OFF
ON
151
ON
ON
ON
OFF
ON
OFF
OFF
ON
152
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
153
ON
OFF
OFF
ON
ON
OFF
OFF
ON
154
OFF
ON
OFF
ON
ON
OFF
OFF
ON
155
ON
ON
OFF
ON
ON
OFF
OFF
ON
156
OFF
OFF
ON
ON
ON
OFF
OFF
ON
157
ON
OFF
ON
ON
ON
OFF
OFF
ON
158
OFF
ON
ON
ON
ON
OFF
OFF
ON
159
ON
ON
ON
ON
ON
OFF
OFF
ON
160
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
161
ON
OFF
OFF
OFF
OFF
ON
OFF
ON
162
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
163
ON
ON
OFF
OFF
OFF
ON
OFF
ON
164
OFF
OFF
ON
OFF
OFF
ON
OFF
ON
165
ON
OFF
ON
OFF
OFF
ON
OFF
ON
166
OFF
ON
ON
OFF
OFF
ON
OFF
ON
167
ON
ON
ON
OFF
OFF
ON
OFF
ON
168
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
169
ON
OFF
OFF
ON
OFF
ON
OFF
ON
170
OFF
ON
OFF
ON
OFF
ON
OFF
ON
171
ON
ON
OFF
ON
OFF
ON
OFF
ON
172
OFF
OFF
ON
ON
OFF
ON
OFF
ON
173
ON
OFF
ON
ON
OFF
ON
OFF
ON
174
OFF
ON
ON
ON
OFF
ON
OFF
ON
175
ON
ON
ON
ON
OFF
ON
OFF
ON
176
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
177
ON
OFF
OFF
OFF
ON
ON
OFF
ON
178
OFF
ON
OFF
OFF
ON
ON
OFF
ON
179
ON
ON
OFF
OFF
ON
ON
OFF
ON
180
OFF
OFF
ON
OFF
ON
ON
OFF
ON
181
ON
OFF
ON
OFF
ON
ON
OFF
ON
182
OFF
ON
ON
OFF
ON
ON
OFF
ON
183
ON
ON
ON
OFF
ON
ON
OFF
ON
184
OFF
OFF
OFF
ON
ON
ON
OFF
ON
185
ON
OFF
OFF
ON
ON
ON
OFF
ON
54 / 43
186
OFF
ON
OFF
ON
ON
ON
OFF
ON
187
ON
ON
OFF
ON
ON
ON
OFF
ON
188
OFF
OFF
ON
ON
ON
ON
OFF
ON
189
ON
OFF
ON
ON
ON
ON
OFF
ON
190
OFF
ON
ON
ON
ON
ON
OFF
ON
191
ON
ON
ON
ON
ON
ON
OFF
ON
192
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
193
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
194
OFF
ON
OFF
OFF
OFF
OFF
ON
ON
195
ON
ON
OFF
OFF
OFF
OFF
ON
ON
196
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
197
ON
OFF
ON
OFF
OFF
OFF
ON
ON
198
OFF
ON
ON
OFF
OFF
OFF
ON
ON
199
ON
ON
ON
OFF
OFF
OFF
ON
ON
200
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
201
ON
OFF
OFF
ON
OFF
OFF
ON
ON
202
OFF
ON
OFF
ON
OFF
OFF
ON
ON
203
ON
ON
OFF
ON
OFF
OFF
ON
ON
204
OFF
OFF
ON
ON
OFF
OFF
ON
ON
205
ON
OFF
ON
ON
OFF
OFF
ON
ON
206
OFF
ON
ON
ON
OFF
OFF
ON
ON
207
ON
ON
ON
ON
OFF
OFF
ON
ON
208
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
209
ON
OFF
OFF
OFF
ON
OFF
ON
ON
210
OFF
ON
OFF
OFF
ON
OFF
ON
ON
211
ON
ON
OFF
OFF
ON
OFF
ON
ON
212
OFF
OFF
ON
OFF
ON
OFF
ON
ON
213
ON
OFF
ON
OFF
ON
OFF
ON
ON
214
OFF
ON
ON
OFF
ON
OFF
ON
ON
215
ON
ON
ON
OFF
ON
OFF
ON
ON
216
OFF
OFF
OFF
ON
ON
OFF
ON
ON
217
ON
OFF
OFF
ON
ON
OFF
ON
ON
218
OFF
ON
OFF
ON
ON
OFF
ON
ON
219
ON
ON
OFF
ON
ON
OFF
ON
ON
220
OFF
OFF
ON
ON
ON
OFF
ON
ON
221
ON
OFF
ON
ON
ON
OFF
ON
ON
222
OFF
ON
ON
ON
ON
OFF
ON
ON
223
ON
ON
ON
ON
ON
OFF
ON
ON
224
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
225
ON
OFF
OFF
OFF
OFF
ON
ON
ON
226
OFF
ON
OFF
OFF
OFF
ON
ON
ON
227
ON
ON
OFF
OFF
OFF
ON
ON
ON
228
OFF
OFF
ON
OFF
OFF
ON
ON
ON
229
ON
OFF
ON
OFF
OFF
ON
ON
ON
230
OFF
ON
ON
OFF
OFF
ON
ON
ON
231
ON
ON
ON
OFF
OFF
ON
ON
ON
232
OFF
OFF
OFF
ON
OFF
ON
ON
ON
233
ON
OFF
OFF
ON
OFF
ON
ON
ON
234
OFF
ON
OFF
ON
OFF
ON
ON
ON
235
ON
ON
OFF
ON
OFF
ON
ON
ON
236
OFF
OFF
ON
ON
OFF
ON
ON
ON
55 / 43
237
ON
OFF
ON
ON
OFF
ON
ON
ON
238
OFF
ON
ON
ON
OFF
ON
ON
ON
239
ON
ON
ON
ON
OFF
ON
ON
ON
240
OFF
OFF
OFF
OFF
ON
ON
ON
ON
241
ON
OFF
OFF
OFF
ON
ON
ON
ON
242
OFF
ON
OFF
OFF
ON
ON
ON
ON
243
ON
ON
OFF
OFF
ON
ON
ON
ON
244
OFF
OFF
ON
OFF
ON
ON
ON
ON
245
ON
OFF
ON
OFF
ON
ON
ON
ON
246
OFF
ON
ON
OFF
ON
ON
ON
ON
247
ON
ON
ON
OFF
ON
ON
ON
ON
248
OFF
OFF
OFF
ON
ON
ON
ON
ON
249
ON
OFF
OFF
ON
ON
ON
ON
ON
250
OFF
ON
OFF
ON
ON
ON
ON
ON
251
ON
ON
OFF
ON
ON
ON
ON
ON
252
OFF
OFF
ON
ON
ON
ON
ON
ON
253
ON
OFF
ON
ON
ON
ON
ON
ON
254
OFF
ON
ON
ON
ON
ON
ON
ON
255
ON
ON
ON
ON
ON
ON
ON
ON
Table 29: SWITCH2 SETTING
6.2. OSD MENU DIAGRAM (Under Camera Option for all Veilux 27X please see pages 2334
Please see the next two page of the OSD lay out for all Veilux PTZ’s below. Please not the Camera option
listed below id for the Sony 18X & 36X option only.
56 / 43
ZONE NUMBER 1
PRESET LABEL 1 - - - - 0 1 2 3 4 5 6 7 8 9 Y Z y
z
A B C D E F G H I J K L M
N O P Q R S T U V W X
a b c d e f g h I j k l m
n o p q r s t u v w x
OK CANCEL
SPACE
BACKSPACE`
ZONES
ZONE NUMBER 1
…ZONE NOT DEFINED…
<EDIT ZONE LABEL>
<EDIT ZONE>
ENABLE ZONE ON
<CLEAR CURRENT ZONE >
BACK
EXIT
< SYSTEM INFORMATION >
< DISPLAY SETUP >
< DOME SETTINGS 1 >
< DOME SETTINGS 2 >
< DOME LABEL >
RESET CAMERA
REBOOT SYSTEM
LANGUAGE
ENGLISH
EXIT
MAIN
MENU
SYSTEM INFORMATION
COM 2400,N,8,1
ADDRESS 1
PROTOCOL PELCO-D
PRESETS 256
LANGUAGE ENGLISH
TEMPERATURE 36°C
SOFTWARE VERSION V4.3.3
BACK
EXIT
DISPLAY SETUP
LABEL
ZONE LABEL ON
ZOOM ON
P/T DEG ON
DOME LABEL ON
<LABEL POSITION>
TEMPERATURE OFF
BACK
EXIT
DOME
<CAMERA>
<MOTION>
<POWER UP>
<PRESETS>
<PATTERNS>
<ZONES>
<CLEAR SET>
TOTAL PRESETS NUMBER 256
BACK
EXIT
<ALARMS>
<ADDR SETTING>
<PASSWORD>
<WINDOWS BLANKING>
<HEATER SETTING>
<CRUISE SETTING>
<TRACKING SETTING>
BACK
EXIT
(To be continued)
SETTI NGS1
DOME SETTINGS 2
PRESET
ON
ZONE DOME PRESET
SAVE
RESET
P/T DEG ZOOM
CAMERA
MOTION
POWER UP
PRESE TS
PATTE RNS
15S
PATTER N>
1
DIGITAL ZOOM OFF
BACKLIGHT COMP OFF
<PROGRAM AE MODE>
<ADDITIONAL>
WIDE DYNAMIC RANGE OFF
BACK
EXIT
AUTO FLIP ON
PROPORTIONAL PAN ON
PARK TIME
PARK ACTION NONE
SCAN SPEED<DEG/S> 1
<SET SCAN>
<MANUAL LIMIT>
<SET AZIMUTH ZERO>
<CLEAR AZIMUTH ZERO>
BACK
EXIT
POWER UP ACTION NONE
BACK
EXIT
PRESET NUMBER 1
…PRESET NOT DEFINED…
<EDIT PRESET LABEL>
<EDIT PRESET POSITION>
<CLEAR CURRENT PRESET>
BACK
EXIT
PATTERN NUMBER
<PROGRAM PATTERN>
<CLEAR CURRENT
BACK
EXIT
PROGRAM AE CONTROL
AE MODE AUTO
LOW LIGHT MODE AUTO
LOW LIGHT LIMIT 1/50
IRIS LEVEL F2.0
AGC LEVEL 0DB
BRIGHT
LEVEL 0DB/F2.0
SPOT AE OFF
BACK
EXIT
ADDIT IONAL
IR SW MODE AUTO
IR STATUS OLOR
AUTO IRIS ON
SHARPNESS ON
SHARPNESS LEVEL 5
AUTO WHITE BALANCE AUTO
R GAIN 214
B GAIN 164
BACK
EXIT
PRESET NUMBER 1
PRESET LABEL 1 - - - - 0 1 2 3 4 5 6 7 8 9 Y Z y
z
A B C D E F G H I J K L M
N O P Q R S T U V W X
a b c d e f g h I j k l m
n o p q r s t u v w x
OK CANCEL
SPACE
BACKSPACE`
CLEAR SET
CLEAR ZONES
CLEAR PRESETS
CLEAR PATTERNS
RESTORE FACTORY DEFAULT
BACK
EXIT
57 / 43
DOME SETTINGS 2
<ALARMS>
<ADDR SETTING>
<PASSWORD>
<WINDOWS BLANKING>
<HEATER SETTING>
<CRUISE SETTING>
<TRACKING SETTING>
BACK
EXIT
<EDIT DOME
<CLEAR DOME
BACK
EXIT
DOME
LABEL
LABEL>
LABEL>
ALARMS
ALARM NUMBER 1
SEQUENCE(SECS) 1
ALARM ACT CRUISE
ACTIVATE AUX OFF
<CLEAR SET>
DWELL TIME<SECS>1 0
DWELL TIME<SECS>2 0
BACK
EXIT
ADDR SETTING
ADDR TYPE HARD
ADDR SOFT 255
ADDR HARD 0
BACK
EXIT
PASSW ORD
ENABLE PASSWORD
<EDIT PASSWORD>
BACK
EXIT
WINDOWS
STYLE
BLANK ALL ABOVE OFF
BALANK ALL BELOW OFF
<SET
WINDO WS>
SET MASK
BACK
EXIT
HEATER DISPLAY ON
HEATER MODE AUTO
TEMPERATURE SET 33℃
BACK
EXIT
DWELL
PRESET
OFF
1234567890 <PRESET 1-10>
01100 10111
BACK
EXIT
DEFAULT
SIZE
GRAY SENS MEDIUM
LOST ACT STOP TRACK
ZOOM
WAIT
<TRACKING
AUX
TRACKING SPEED AUTO
TRACKING TIME<M> AUTO
BACK
EXIT
DOME LABEL
0 1 2 3 4 5 6 7 8 9 Y Z y
z
A B C D E F G H I J K L M
N O P Q R S T U V W X
a b c d e f g h I j k l m
n o p q r s t u v w x
OK CANCEL
SPACE BACKSPACE
COLOR
HEATER
CRUISE
TIME< SECS>
LIST
1 ON
TRACKING
SETTI NG
SENS
SETTI NG
TIME< S>
BOUND ARY>
EDIT DOME LABEL
OFF
BLANK ING
SETTI NG
ON
40
SETTING
MEDIUM
GRAY
OFF
SET
WINDO WS
WINDOWS NUMBER 1
<EDIT WINDOW LOCATION>
<EDIT WINDOW ZOOM >
4
ENABLE WINDOW OFF
CLEAR CURRENT WINDOW
BACK
EXIT
EDIT WINDOW
IRIS OPEN TO CONTINUE
IRIS CLOSE TO CANCEL
ZOOM
EDIT WINDOW
IRIS OPEN TO CONTINUE
7
1
0
IRIS CLOSE TO CANCEL
TRACKING BOUNDARY
BOUNDARY LIMIT OFF
CLEAR BOUNDARY
LEFT LIMIT OFF
RIGHT LIMIT OFF
UP LIMIT OFF
DOWN LIMIT OFF
BACK
EXIT
LOCAT ION
Loading...