Veilux VP-F18X, VP-AT18X, VP-ATDN18X, VP-ATDN27X, VP-ATDN36X Installation And User Manual

i / iii

INSTALLATION & USER MANUAL

Auto Tracking / High Speed PTZ Camera

ii / iii

Thank You for Choosing Our PTZ Camera!

When you open the box:

 Check that the packing and the contents are not visibly damaged. Contact the retailer immediately if any parts are

either missing or damaged.

 Make sure if the contents are all included as per the packing list.  Do not attempt to use the device with missing or damaged parts. Send the product back in its original packing if it is

damaged.

 The information contained in the document is subject to change without notice.

iii / iii

Table of Contents

1. Safety Notes --- Important!!! ............................................................................................................................. 1

2. About The Product ............................................................................................................................................ 2

2.1. Features .................................................................................................................................................. 2

2.2. Functions ................................................................................................................................................. 2

2.3. Technical Parameters.............................................................................................................................. 4

2.3.1. SONY Modules & Veilux Modules ............................................................................................... 4

3. Installation ......................................................................................................................................................... 5

3.1. DIP Switch Setting ................................................................................................................................... 5

3.2. Installation ............................................................................................................................................... 5

3.2.1. Wall Mount Installation ................................................................................................................. 5

3.2.2. In-ceiling Mount Installation.......................................................................................................... 7

3.2.3. Surface Mount Installation.......................................................................................................... 10

3.2.4. Pole Mount Installation............................................................................................................... 11

4. Operation Guide .............................................................................................................................................. 12

4.1. Operation At Power Up.......................................................................................................................... 12

4.2. How To Use Our Control Keyboard ....................................................................................................... 12

4.2.1. Control Keypad Password And Access...................................................................................... 12

4.2.2. Control Keypad Command Syntax ............................................................................................. 12

4.2.3. Control Keypad Command Types .............................................................................................. 13

4.3. Select A Camera ................................................................................................................................... 13

4.4. Camera Motions .................................................................................................................................... 13

4.4.1. Pan And Tilt ............................................................................................................................... 13

4.4.2. Zoom.......................................................................................................................................... 14

4.4.3. Focus ......................................................................................................................................... 14

4.4.4. IRIS Opening ............................................................................................................................. 14

4.4.5. Preset Positions Programming and Recalling ............................................................................ 15

4.5. Function Program Menu ........................................................................................................................ 15

4.5.1. Product Information.................................................................................................................... 16

4.5.2. Display Setup............................................................................................................................. 16

4.5.2.1. Label Position ................................................................................................................... 17

4.5.3. Main Programming Menu (Dome Settings 1) ............................................................................. 17

4.5.3.1. Camera ............................................................................................................................. 18

4.5.3.2. Motion ............................................................................................................................... 20

4.5.3.3. Power Up .......................................................................................................................... 22

4.5.3.4. Presets.............................................................................................................................. 22

4.5.3.5. Patterns ............................................................................................................................ 23

4.5.3.6. Zones................................................................................................................................ 24

4.5.3.7. Clear Set........................................................................................................................... 24

4.5.3.8. Preset Number.................................................................................................................. 25

4.5.4. Secondary Programming Menu (Dome Settings 2).................................................................... 25

4.5.4.1. Alarm Submenu ................................................................................................................ 25

4.5.4.2. Address setting................................................................................................................. 26

4.5.4.3. Password .......................................................................................................................... 27

4.5.4.4. Windows Blanking ............................................................................................................ 28

4.5.4.5. Heater Setting ................................................................................................................... 30

4.5.4.6. Cruise Setting ................................................................................................................... 30

4.5.4.7. Tracking Setting ................................................................................................................ 31

4.5.5. Dome Label................................................................................................................................ 33

4.6. Special Control Panel Commands ......................................................................................................... 34

5. Trouble Shooting............................................................................................................................................. 35

6. Annex ............................................................................................................................................................... 36

6.1. DIP Switch Chart ................................................................................................................................... 36

6.2. OSD Menu Diagram .............................................................................................................................. 41

1 / 43

1. SAFETY NOTES --- IMPORTANT!!!

The following important notes must be followed carefully to run the PTZ camera and respective accessories in total safety. The camera and relative accessories are called video system in this section.

Use the instructions correctly and fully Read all safety rules and instructions carefully before starting to run the video system.

Follow the instructions in the instruction manual. Pay attention to all warnings on the camera and in the instruction manual. Keep the safety notes and instructions for future reference.

Attachments & Accessories Do not use attachments other than those recommended in the instruction manual because this could cause risks to the products. Only use the recommended accessories for the camera for installation and operation.

Protect the video system To protect the camera, avoid installing and using it in direct sunlight or any source of bright light. Bright light, like that from a spotlight, can cause dimming and blurs. A vertical line may appear on the screen. This does not indicate a problem.

Keep it away from rain and dust. Do not touch the zoom lens with your fingers. If needed, use a soft cloth and methylated spirit to remove traces of dust. Apply a specific cap to protect the zoom lens when the camera is not in use.

Install the camera away from video interference. The pictures could present interference if the leads are arranged near a TV set or other device. Either move the leads or re-install the device to solve the problem.

Do not use any part of the video system near water, i.e. bathtubs, wash basins, sinks, tubs, on damp surfaces, near swimming pools, etc. Do not insert objects of any kind through the camera openings to avoid touch live parts: fire and electrocution risk. Do not pour any kind of liquid on the device.

A switch for performing maintenance operations on the camera must be included. Connect the camera only to the electrical power supply shown on the ratings plate. Contact your retailer if in doubt.

Lay the power wires keeping them from being trodden on or squeezed by objects placed on top of them. Pay particular attention to leads near plugs, screws and the product outlet.

Disconnect the power lead and the wiring to protect the camera during electrical storms or when it is left unattended and not used for a long time. This will prevent damage to the video system in the event of lightening or electrical line overload.

Do not overload the electrical power and the extensions to prevent the risk of fire or electrocution. Do not place the camera near or over radiators or sources of heat. Check that the area is suitably ventilated before

installing the camera inside partially closed areas (such as recesses, bookshelves and shelves). Do not position the camera on unsteady trolleys, stands, brackets or tables. The camera could fall and severely injury

adults and children in addition to seriously damaging the product. Maintenance & Repairs

Always contact a qualified service technician to repair the camera (or any other part of the video system). Unauthorized opening or removing the lids may cause fire and electrocution risk and other dangers.

Disconnect all electrical parts from the mains before cleaning. Uses spare parts specified by the manufacturer or spare parts with equivalent characteristics when replacements

required. Unauthorized replacements can cause fires, electrical shocks and other dangers. After any servicing intervention or repair to the video system, ask the technician to run a safety check to ensure that

everything is working safely. Damage requiring professional assistance

Disconnect the video system from the power mains and call qualified service personnel in the following cases:



 If the power lead or plug is damaged.  If liquid or foreign objects accidentally penetrate inside the device.  If the device was exposed to rain or water.  If the device was dropped, subjected to heavy shocks or if the camera packaging was damaged.  If the device performance changes considerably.

2 / 43

2. ABOUT THE PRODUCT

The tracking PTZ is based on our unique motion tracking technology with high position resolution, high speed, low price and selectable communication protocols. It is widely used in surveillance system as unattended CCTV device.

2.1. FEATURES

 Auto tracking of moving object (auto PTZ) based on our motion tracking technology;  Max 36X optical, 0.01Lux of module specifications;  360º horizontal rotation at maximum speed of 240º /sec;  Auto cruise function with 256 preset positions;  Built-in OSD Menu, to change dome parameter, achieve auto scan, and pattern etc;  Features password protection to prevent unauthorized changes to the dome setting;  Windows blanking and tracking boundary for privacy purpose;  EasyClip installation features;  The feature of defining specific activity when the dome parks;  Auto-flip to follow object and surveillance of any subject that is constant and continuous;  The speed can be adjusted automatically according to zooming times;  Auto focus lens and auto white balance, BLC function;  Multi protocol compatible (Pelco-P, Pelco-D etc);  Alarm input, Alarm output, Alarm action.

2.2. FUNCTIONS

Object Tracking

In auto tracking mode, the camera can track a moving object in the target area with auto pan, tilt and zoom whic h realizes smart unattended surveillance.

Tracking Cruise The tracking function can be activated during cruise. At a preset of the cruise list, the camera can track moving objects automatically.

Soft Address The camera address can be programmed with built-in OSD menu, and the user does not need to dismount the camera from field or do any screw work.

Wide Dynamic Range (WDR) A camera is intended to provide clear images even under back light circumstances where intensity of illumination can vary excessively, when there are both vary bright and vary dark areas simultaneously in the field of view. WDR enables the capture and display of both bright areas and dark areas in the same frame, in a way that there are details in both areas, i.e. bright areas are not saturated, and dark areas are not too dark.

Day/Night Function The IR cut filter of camera module inside the camera can be removed by sending special command, so that the camera can change from color to mono. The picture is clear even if the illumination is as low as 0.01Lux.

 Wide Dynamic Range (WDR) and Day/Night function are based on the relative modules. Please refer to technical

parameters.

Proportional Pan Proportional pan automatically reduces or increases the pan and tilt speeds in proportion to the zooming times. At telephoto zoom settings, the pan and tilt speeds will be slower for a given amount of joystick deflection than at wide zoom settings. This keeps the image from moving too fast on the monitor when there is a large amount of zoom.

Auto Flip When the camera tilts downward and goes just beyond the vertical angle, the camera rotates 180º. When the camera rotates (flips), the camera starts moving upward as you continue to hold joystick in the down position. Once you let go of the joystick after the dome rotates, joystick control returns to normal operation. The auto-flip feature is useful for following a person who passes directly beneath the camera.

Save/Call Preset Preset function is that dome saves current horizontal angle and title angle of pan/tilt, zoom and position parameters into

3 / 43

memory. When necessary dome calls these parameters and adjusts Pan/Tilt and camera to that position. User can save and call presets easily and promptly by using keyboard controller or infrared controller. The camera supports up to 256 presets.

Lens Control

1) Zoom control User can adjust zoom wide or tele by controller to get desired image.

2) Focus control System defaults Auto Focus mode, that is, the lens and camera will automatically adjust the focus to get the best image.

Focus can also be controlled manually from the controller if required. Press Focus Near or Focus Far key to manually focus. Focus can be manual via keyboard or matrix, please refer to control keyboard or matrix operation manual for detailed operation. When adjusting position is set with focus status, it goes back to auto focus.

The camera will NOT auto focus in the following status.

 Target is not in the center of image.  Targets are in near and far at the same time.  Target is of strong light object. Such as spotlight etc.  Target is behind the glass with water drop or dust.  Target moves too fast.  Large area target such as wall.  Target is too dark or vague.

3) IRIS control System defaults Auto IRIS. Camera can adjust immediately according to the alteration of back ground illumination so that a lightness steady image can be achieved.

You may adjust IRIS by controller to get required image brightness, and call back Auto IRIS by controlling the joystick. Auto White Balance

Camera can automatically adjust white balance (WB) according to the alteration of background lightness to give a true color image.

Back Light Compensation (BLC) If a bright backlight presents, the subjects in the picture may appear dark or as a silhouette. Backlight compensation enhances objects in the center of the picture. The camera uses the center of the picture to adjust the IRIS. If there is a bright light source outside this area, it will wash out to white. The camera will adjust the IRIS so that the object in the sensitive area is properly exposed.

Auto Cruise The preset position is programmed to be recalled in sequence. This feature is called auto cruise. Up to 30 presets can be saved in each cruise tour.

Patterns A pattern is a saved, repeating, series of pan, tilt, zoom and preset functions that can be recalled with a command from a controller or automatically by a programmed function (alarm action or park action or power-up action).

Auto, Random and Frame Scan Auto Scan: Make the camera scan 360º ranging from the current position. Random Scan: Make the camera random scan 360º ranging from the current position. Frame Scan: This feature freezes the scene on the monitor when going to a preset. This allows for smooth transition from one preset scene to another.

Zones Setting A zone is a pan area, defined by a left and right limit, on the 360º pan plane. The camera has eight zones, each with a 6-character label.

Alarms Input The camera has four alarm inputs, which can be programmed as high, medium or low priority. When an alarm is received, an input signal to the camera triggers the user-defined action (go to preset, run pattern, etc.) programmed for the alarm.

Auxiliary Output An auxiliary output is a programmable signal from the camera back box that can trigger another device to operate. An auxiliary output is programmable to trigger from an alarm or from a controller.

4 / 43

Password Protection The camera features password protection to prevent unauthorized changes to the camera settings. You can open the System Information and Display Setup Screens, but cannot access any of the camera Settings menus.

Windows Blanking A set window can be saved so that it is the only blanked tilt area of the scene. All other parts of the tilt area of the scene will be visible.

 Windows blanking is only available for Sony Modules at present.

2.3. TECHNICAL PARAMETERS

2.3.1. SONY & VEILUX MODULES

Model #

VP-F18X (18X)

VP-AT18X (18X)

VP-ATDN18X (18X)

Module Brand

Sony

Signal Format

PAL/NTSC

Image Sensor

¼ inch color CCD

H. Resolution

550 TVL

Video Out

1.0±0.2VP-P

P/T Speed

Pan:0.05º～240º/sec ;Tilt:0.03º～160º/sec

Pan:0.05º～240º/sec;Tilt:0.03º～160º/sec

S/N Ratio

≥50DB

AGC

Auto/Manual

BLC

Auto/Manual

IR cut Filter

Yes

(WDR)

No

Optical Zoom

18X

Digital Zoom

12X

Model #

VP-FDN27X (27X)

VP-ATDN27X (27X)

VP-ATDN36X (36X)

Module Brand

Veilux

Sony

Signal Format

PAL/NTSC

Image Sensor

¼ inch color CCD

H. Resolution

580 TVL

520 TVL

Video Out

1.0±0.2VP-P

P/T Speed

Pan:0.05º～240º/sec ;Tilt:0.03º～160º/sec

Pan:0.05º～240º/sec;Tilt:0.03º～160º/sec

S/N Ratio

≥50DB

AGC

Auto/Manual

BLC

Auto/Manual

IR cut Filter

Yes

(WDR)

No

Yes

Optical Zoom

27X

36X

Digital Zoom

10X

12X

Table 1: Sony Modules

 The specifications are subject to change without notice.

5 / 43

3. INSTALLATION

This section contains detailed instructions for installing the camera. These instructions assume that the installer has a good knowledge of installation techniques and is capable of adopting safe installation methods.

3.1. DIP SWITCH SETTING

Before installing the camera drive, check the DIP switches; configure the receiver address, communication protocol, and baud rate setting. Pic. 1 shows switches position and default settings. SW1 switches (1bit) and SW2 switches (1, 2, and 7 bit) are set to the ON position. For normal user, setting switches to default position is enough.

Pic. 1 Switch Position

The camera can be controlled via various communication protocols by setting SW1 switches(1, 2, 3,and 4) and operate at 1200bps, 2400bps, 4800bps, 9600bps and 19200bps baud rate by setting SW1 switches(5, 6, 7, and 8). Do not set the switches to reserved position. Pic. 2 shows the default settings for the DIP switches.

Pic. 2 Default settings of DIP switches

Please refer to Table 28: SWITCH1 SETTING and Table 29: SWITCH2 SETTING in Section 6.1 to set baud rate, and communication protocol type and camera address.

 Always use the “PELCO P” or “PELCO D” protocols.  Do not use address “0” with the “PELCO P” or “PELCO D” protocols.

3.2. INSTALLATION

The camera has four types of mountings: wall mount, in-ceiling mount, surface mount, and pole mount. Please make sure which type you are installing.

3.2.1. WALL MOUNT INSTALLATION (WITH POWER BOX)

Step 1. Install the power box on wall

Pic. 3

Install the power box to the wall with 4 screws.

 When installing outdoors, make sure installation is properly sealed to keep moisture out.

6 / 43

Pic. 6.

e back box. Take out hole of pin. Screw the me

 To install the pt z camera with no power box, install the bracket directly onto the wall and then go to Pic 6.

Pic. 4

Pull the cables (of video, alarm, control etc.) through the cable hole of the power box and do necessary connections. The cables are supplied by user.

Pic. 5

Refer to the instructions supplied with the bracket. Take out cables for the dome through the bracket. And install the bracket to the power box. See Pic. 5

Pic. 6

Press the thumb fastener and open the hinged door to th tal cover into the bracket. See

Pic. 7

Connect cables to hole of pin. Insert the pin inside the back box. When finished, close the door to the back box and turn on the power. The LED will light up. See Pic. 7.

 If the LED does not light up, refer to Section 5: Trouble Shooting.

Step 2. Install dome drive

7 / 43

Pic. 8

Set the DIP switches for SW1 and SW2 at the bottom of the dome drive for the appropriate receiver address, communication protocol, and baud rate. Refer to the labels on the dome drive or DIP SWITCH SET at the beginning of this manual.

Remove cover of camera and sponge. See Pic. 8.

Pic. 9

Line up link card and faucet of the back board of the dome. Push the dome drive in. See Pic. 9.

Step 3. Install lower dome.

Pic. 10

Take out a screw from lower dome. Link cables, screw, and lower dome. See Pic. 10.

Pic. 11

Line up the mounting screw holes, and install the two mounting screws. Push the lower dome inside the back box. See Pic. 11.

Pic. 12

Screw the two mounting screws, and screws in the bracket. See Pic. 12.

3.2.2. IN-CEILING MOUNT INSTALLATION

8 / 43

Step 1. Prepare In-ceiling

Pic. 13

Locate the center point of the in-ceiling mounting location. Insert the compass tool into the hole. Draw a circle on the ceiling using the compass tool and a pencil. See Pic. 14 (Left).

Cut the circle out of the ceiling tile. See Pic. 14 (Right).

Pic. 14

Put the reinforcing metal plate (see following pic.) on top of the ceiling (behind the ceiling) with the two circles aligned vertically.

Pic. 15

Step 2. Install back box

Pic. 16

Take out bracket from back box. Insert the back box into ceiling. See Pic. 16. Install a safety chain/cable (not supplied) that can stand up to 32 pounds (14.6kg). Press the thumb fastener and open the

hinged door to the back box. Take out hole of pin. See Pic. 17

9 / 43

through the plastic panel. Connec

t cables to hole of pin. See Pi

Pic. 17

Pull cables into the back box c. 18

Pic. 18

Insert the hole of pin inside the back box. When finished, close the door to the back box and turn on the power. The LED will light up. See Pic. 19.

Pic. 19

 If the LED does not light up, refer to Section 5: Trouble Shooting.

Step 3. Install dome drive Set the DIP switches for SW1 and SW2 at the bottom of the camera drive for the appropriate receiver address, communication protocol, and baud rate. Refer to the labels on the camera drive or DIP SWITCH SET in this manual.

Remove cover of camera and sponge. See Pic. 20

Pic. 20

Line up link card and faucet of the back board of the dome. Push the dome drive in. See Pic. 21

10 / 43

r dome

Pic. 21

Step 4. Install lowe

Pic. 22

Take out a screw from lower dome. Link cables, screw, and lower dome. See Pic. 22.

Pic. 23

Line up the snaps on trim ring with the mounting screws on the back box. Snap the trim ring into the plastic snap washers on the mounting screws. See Pic. 23.

3.2.3. SURFACE MOUNT INSTALLATION

Step 1. Install back board of surface mount

Pic. 24

Locate the back board of the camera location. Drill a hole in the ceiling using a drill. Insert the screw and back board into the hole. See Pic. 24

Pic. 25

Press the thumb fastener and open the hinged door to the back box. Take out hole of pin. See Pic. 26.

11 / 43

Pic. 26

Pull cables into the back box into the plastic panel. Connect cables to hole of pin. Insert the hole of pin inside the back board. When finished, close the door to the back board and turn on the power. The LED will light up. See Pic. 26.

 If the LED does not light up, refer to Section 5: Trouble Shooting.

Step 2. Install dome drive

Set the DIP switches for SW1 and SW2 on the bottom of the dome drive for the appropriate receiver address, communication protocol, and baud rate. Refer to the labels on the dome drive or DIP SWITCH SET in this manual.

Pic. 27

Line up link card and faucet of the back board of the dome. Push the dome drive in. See Pic. 27. Step 3. Install dome flange

Pic. 28

Snip a flake piece. Keep three flanges away from two clamps on the back board. See Pic. 28.

Pic. 29

Push the flange of dome into the back board. Take out the membrane on the clarity flake of the dome drive. See Pic. 29.

3.2.4. POLE MOUNT INSTALLATION

See Section 3.2.1 Wall Mount Installation.

12 / 43

4. OPERATION GUIDE

4.1. OPERATION AT POWER UP

The camera employs the default settings the first time it is switched on. Changes to the settings will be permanently stored and will be made available the ne xt time the camera is switched on. You can return to the default settings by means of the appropriate menu option at any time.

The camera will work as follows when it is switched on. The camera will run a calibration procedure and a message showing the following information will appear on the video

output OSD (On Screen Display): protocol, communication parameters, camera address and software version.

PROTOCOL: PELCO-D COM: 9600, N, 8, 1 ADDR: 1 SOFTWARE VERSION V4.3.3

Check that the data are suitable for operation. Otherwise, refer to the section in this document that shows how to install the camera correctly.

At the end of the calibration step, the camera will switch to stand-by as programmed (POWER UP ACTION in DOME SETTINGS1 > POWER UP). The camera will continue working this way until any command is received from the keypad. The camera during this phase can be pointed to a fixed point or pan across the field. Refer to the detailed described in the POWER UP ACTION menu section for more details.

4.2. HOW TO USE OUR CONTROL KEYBOARD

The camera is ready to receive commands from our control keyboard (see figure below) after connecting.

4.2.1. CONTROL KEYPAD PASSWORD AND ACCESS

The system will wait for the password to be entered after being switched on. The control panel requires a 6-digit password. The entered digits will be replaced by a “*” symbol on the screen for privacy. Access to the menu is gained after entering all the digits correctly. Refer to the corresponding manual for using the control panel.

 The default user password is “000000”.  It is advisable to change the default password to prevent intrusions.  Do not lose or forget the programmed password.  Take note of the new password and keep it in a safe place.

4.2.2. CONTROL KEYPAD COMMAND SYNTAX

Controls can use the joystick, single keys or key combinations. The key command syntax is shown below.

13 / 43

Key command syntax The syntax used in this manual for controls using keys consists of various elements (words and three digit numbers). Each command is always in braces and each element is separated by commas. Each word or decimal digit used in the

14 / 43

syntax is identified by a corresponding key on our control panel. Words can be enclosed in round brackets, square brackets or no brackets. Three digit decimals are never enclosed in brackets.

The following words only can be used: PRESET, CALL, ESC, OPEN, CLOSE, NEAR, FAR, ZOOM OUT, ZOOM IN,

CAM, MON, SCAN, ENTER. The decimal digits are: 0, 1, 2, 3, 4, 5, 6, 7, 8,

and 9. Some application examples of controls are shown in detail below. Using the joystick

A command can also be given simply by moving the joystick because this generates actions on the camera or OSD (On Screen Display) menu.

Using a single key Pressing a single key can cause camera action. For example, the following command will zoom out of the frame. Underling indicates the key is in use.

ZOOM OUT

Key combinations Pressing a key combination in rapid sequence extents the command set. For example, the foll owing command (select camera address 1) is performed by pressing the following keys:

CAM + 1 + ENTER

4.2.3. CONTROL KEYPAD COMMAND TYPES

There are four command types:

 Select camera,  Move camera (tilt and pan, zoom, adjust focus and IRIS opening, go to preset positions),  Adjust camera operation mode using menus,  Various quick controls operable from the control panel.

The method for accessing these controls will be shown in detail in the following paragraphs.

4.3. SELECT A CAMERA

The camera to be controlled must be selected first. For example, the following command selects camera 1: CAM + 1 + ENTER After this operation, the message CAM 1 will appear on the control panel display.

4.4. CAMERA MOTIONS

After selecting a camera, it can be moved either directly using the control panel as described below:

 Panning (horizontal) and tilting (vertical).  Zooming, focusing and IRIS opening.  Preset positions programming and recalling.

These functions can be directly accessed using a single key or joystick or a simple key combination.

4.4.1. PAN AND TILT

The camera may be moved using our keyboard controller. Move the joystick vertically to tilt the camera and horizontally to pan it.

The maximum pan span is from 0º to 360º with continuous rotation. The maximum tilt span is from -5º (camera in vertical position) and 92º.

The panning and tilting speed can be modulated by operating the joystick appropriately. Note that the maximum speed that can be obtained by operating the joystick is not always equal to that programmed in

the working settings. This in fact depends on the value of the PROPORTIONAL PAN setting in the MOTION menu and the zoom. If the option is ON, the maximum rotation speed which can be obtained using the joystick is proportional to the

15 / 43

magnification used to obtain the best frame. Panning (horizontal)

Tip the joystick rightwards to turn the camera horizontally clockwise and tip it leftwards to turn it anticlockwise. If no advanced options are set (e.g. range limits set enabled), the camera can be turned continuously without

interruptions. The pan span may be limited between two angles in DOME SETTING1 > MOTION > MANUAL LIMIT. Tilting (vertical)

Tip the joystick upwards to turn the camera vertically upwards and tip it downwards to turn the camera downwards. The camera rotation is limited upwards by the horizontal plane or downwards by the vertical axis.

Performance will change considerably near the vertical axis ac cording to whether the AUTO FLIP is on or not (default setting is on).

 With AUTO FLIP off, the camera will stop in perfectly vertical position and will stop turning when the joystick is tipped

downwards.

 With AUTO FLIP on, the camera will proceed over the vertical axis when the joystick is tipped downwards. This is

because, when the vertical axis is reached, the camera flips automatically by 180 degrees and resumes the initial trajectory.

The AUTO FLIP function can be used to follow a subject arriving in a certain direction passes under the camera and continues in a straight line. To do this, hold the joystick tipped downwards following the movement of the subject. Observe that in this case the joystick performance after the camera passes over the vertical axis opposite to the normal axis because tipping the joystick downwards will turn the camera upwards.

Normal operation of the joystick will be resumed as soon as the downward tip is interrupted (also only for an instant). At this point, to follow the subject in the same direction, you will need to tip the joystick upwards, as you would normally.

4.4.2. ZOOM

The camera frame may be adjusted by using the ZOOM IN and ZOOM OUT commands. Use ZOOM IN to zoom into the detail; use ZOOM OUT to zoom out.

Zoom can be set as per the zoom specifications of relative modules, combined between optical zoom and digital zoom. Refer to the specific section for programming the function.

4.4.3. FOCUS

The camera focus may be adjusted manually using the NEAR and FAR controls. As the auto focus function is always on, a manual setting made using NEAR and FAR will be kept only until a pan, tilt

or zoom command is used. In this case, auto focus will adjust focus automatically again. Refer to the specific section for additional details on focusing and on the various options.

 The auto focus function cannot work correctly in the following cases:

 The object to be focused on is not in the middle of the image.  There are far and near objects in the frame.  Bright light is shining on the subject.  The subject is behind a glass pane covered in drops or dust.  The subject is moving very quickly.  The subject is not well lit.  The subject is too big.

4.4.4. IRIS OPENING

The IRIS opening may be controlled manually using the OPEN and CLOSE commands. The manual setting made using OPEN and CLOSE will be kept only until a pan, tilt or zoom command is used if the

16 / 43

automatic IRIS opening option is enabled (the default setting is on). In this case, the opening will be controlling automatically again.

Refer to the specific section for additional details on IRIS opening adjustment

4.4.5. PRESET POSITIONS PROGRAMMING AND RECALLING

The camera can store up to 256 panning, tilting and zooming configurations (called preset positions) which can be recalled at any time. The manual focusing and IRIS opening settings cannot be stored.

 When storing presets, it is important to remember that some are reserved and cannot be either stored or used for

positioning the camera. Presets from 80 to 99, Presets from 100 to 103, 170 to 173

The following examples show how to program the free Presets and recall them.

Example: programming preset number 32

1) Position the camera in a certain pan, tilt and zoom configuration.

2) Enter the command PRESET + 32 + ENTER. From this moment on, simply enter the command CALL + 32 + ENTER to move the camera to the preset position.

 The saved value will be written over if the setting is reprogrammed.  The Presets are saved in a permanent memory area of the camera where they are maintained also when power

is disconnected. However, RESTORE FACTORY DEFAULT will delete all preset values.

 Press PRESET + 83 + ENTER to delete all the saved presets.  The Presets store the coordinates according to an angular reference system. Therefore, the reference system

zero point may become misaligned with the camera mechanics after prolonged use of the tilting and panning functions. Minor inaccuracies in preset positions may occur. In this case, calibrate the angular coordinate system using the REBOOT SYSTEM command. This calibration is automatically run when the camera is switched on.

4.5. FUNCTION PROGRAM MENU

Use the following control panel command to access the function programming menu. PRESET + 95 + ENTER At this point, if no password is required for access, the following first level menu will appear on the screen:

MAIN MENU

< SYSTEM INFORMATION > < DISPLAY SETUP > < DOME SETTINGS 1 > < DOME SETTINGS 2 > < DOME LABEL > RESET CAMERA REBOOT SYSTEM LANGUAGE ENGLISH EXIT

Screen 1: Main Menu

Otherwise, if a password is required, the following prompt will appear.

PLEASE INPUT PASSWORD

PASSWORD 1 2 3 4 5 6 7 8 9 0

▲

CLEAR ENTER EXIT

Screen 2: Password Protection

The password is a numeric combination (max. 4 digits).

17 / 43

Select the password digits by moving the joystick in the horizontal direction. Symbol “▲” indicates the digit which will be entered.

Press OPEN to enter the selected digit. The entered numbers will be replaced by a “*” symbol on the screen for privacy.

Select ENTER and press OPEN to access the first level menu after entering all the digits correctly.

 The default password is “0000”.  It is advisable to change the default password to prevent intrusions.  Do not lose or forget the programmed password.  Take note of the new password and keep it in a safe place.

Simply move the joystick vertically to scroll the menu and point the cursor to the menu item to be selected: at th is point, select OPEN to access the selected second level.

Simply press BACK and use OPEN to go back to the previous level menu. To completely exit a menu on any level, simply select EXIT and use the OPEN command.

Option

Value

Explanation

SYSTEM INFORMATION

Product information menu (refer to Section 4.5.1).

DISPLAY SETUP

Display menu (refer to Section 4.5.2).

DOME SETTINGS 1

Main programming menu (refer to Section 4.5.3).

DOME SETTINGS 2

Secondary programming menu (refer to Section 4.5.4).

DOME LABEL

Menu for associating the text to be associated to the camera (refer to Section 4.5.5).

RESET CAMERA

This function reset the device without clearing the settings performed by the user. Resets the camera menu settings, except for the password.

REBOOT SYSTEM

This function restarts the device without clearing the settings performed by the user. The camera is repositioned.

LANGUAGE

ENGLISH

Menus in English.

Table 2

4.5.1. PRODUCT INFORMATION

In the first level menu, select SYSTEM INFORMATION to display information concerning the protocol, the camera address, the presetting number, the language of use and the measured temperature.

SYSTEM INFORMATION

COM 2400,N,8,1 ADDRESS 1 PROTOCOL PELCO-D PRESETS 256 LANGUAGE ENGLISH TEMPERATURE 36°C SOFTWARE VERSION V4.3.3 BACK EXIT

Screen 3: System Information

The information in this menu cannot be edited.

4.5.2. DISPLAY SETUP

The DISPLAY SETUP menu is used to enable the labels to be displayed for the various camera functions.

18 / 43

DISPLAY SETUP

PRESET LABEL ON ZONE LABEL ON ZOOM ON P/T DEG ON DOME LABEL ON <LABEL POSITION> TEMPERATURE OFF BACK

Screen 4: Display Menu

Option

Value

Explanation

PRESET LABEL

ON/OFF

Show or hide presetting labels (max. 64).

ZONE LABEL

ON/OFF

Show or hide zone labels.

ZOOM

ON/OFF

Show or hide zoom labels.

P/T DEG

ON/OFF

Show or hide camera pan/tilt degrees. The coordinates refer to the monitor centre.

DOME LABEL

ON/OFF

Show or hide dome labels.

LABEL POSITION

Label positioning submenu (refer to Section 4.5.2.1)

TEMPERATURE

ON/FF

Show or high the camera temperature.

Table 3

4.5.2.1. LABEL POSITION

The labels may be positioned where required on the screen.

ZONE DOME PRESET

SAVE

RESET

P/T DEG ZOOM

Screen 5: Label Position

To establish a position:

1) Point the cursor to the label to be moved by moving the joystick vertically.

2) Press OPEN

3) Symbol “■” will appear.

4) Position the entire label in the chosen position using the joystick.

5) Press OPEN.

6) Repeat this operation for each label.

7) Point the cursor “►” to SAVE and press OPEN.

4.5.3. MAIN PROGRAMMING MENU (DOME SETTINGS 1)

In the first level menu, select <DOME SETTINGS 1> and the corresponding submenus to access the main menus.

DOME SETTINGS1

<CAMERA> <MOTION> <POWER UP> <PRESETS> <PATTERNS> <ZONES> <CLEAR SET> TOTAL PRESETS NUMBER 256 BACK

Screen 6: Dome Settings 1

Option

Value

Explanation

CAMERA

Camera parameter programming submenu (refer to Section

19 / 43

4.5.3.1)

MOTION

Camera motion parameter programming submenu (refer to Section

4.5.3.2)

POWER UP

Power up parameter submenu (refer to Section 4.5.3.3)

PRESETS

Preset parameter submenu (refer to Section 4.5.3.4)

PATTERNS

Pattern parameter submenu (refer to Section 4.5.3.5)

ZONES

Zone parameter programming submenu (refer to Section 4.5.3.6)

CLEAR SET

Clear settings submenu (refer to Section 4.5.3.7)

TOTAL PRESET NUMBER

40/64/256

Maximum number of Presets. Always enter 256 (refer to Section

4.5.3.8)

Table 4

4.5.3.1. CAMERA

The first level of this menu contains the following options grouped as shown in the following table. To edit the value, simply select the required menu item using the joystick with vertical movements and the OPEN

button. Then edit as required. Select BACK/EXIT to close the item.

CAMERA

DIGITAL ZOOM OFF BACKLIGHT COMP OFF <PROGRAM AE MODE> <ADDITIONAL> WIDE DYNAMIC RANGE OFF BACK EXIT

Screen 7: Camera (Sub-Menu)

Option

Value

Explanation

DIGITAL ZOOM

ON/OFF

Switch digital zoom ON or OFF.

BACK LIGHT COMP

ON/OFF

Switch back light compensation ON and OFF. The BACK LIGHT COMPENSATION function is useful for improving visibility when the

background light is very bright.

PROGRAM AE MODE

Automatic exposure submenu (see below)

ADDITIONAL

Additional settings submenu (see below).

WIDE DYNAMIC RANGE

ON/OFF

Activate WDR feature of the camera. This is only available on related optical modules.

Table 5

PROGRAM AE CONTROL submenu - Automatic Exposure settings

PROGRAM AE CONTROL

AE MODE AUTO LOW LIGHT MODE AUTO LOW LIGHT LIMIT 1/50 IRIS LEVEL F2.0 AGC LEVEL 0DB BRIGHT LEVEL 0DB/F2.0 SPOT AE OFF BACK EXIT

Screen 8: Program AE Control

Option

Value

Explanation

AE MODE

AUTO

In this mode:

- The shutter opening time cannot be set and is

automatically adjusted.

- Auto IRIS opening is automatically adjusted.

- Gain control is automatic (AGC ON).

20 / 43

SHUTTER

In this mode:

- The shutter opening time may be varied as programmed

in the “LOW LIGHT LIMIT” menu.

- Auto IRIS opening is automatically adjusted.

- Gain control is automatic (AGC ON).

IRIS

In this mode:

- The IRIS opening time is fixed to 1/50 second.

- The auto IRIS opening is manually varied in the “IRIS

LEVEL” menu.

- Gain control is automatic (AGC ON).

MANUAL

In this mode:

- The shutter opening time may be varied as programmed

in the “LOW LIGHT LIMIT” menu.

- The auto IRIS opening is manually varied in the “IRIS

LEVEL” menu.

- AGC gain control is variable as programmed in the “AGC

LEVEL” menu. All items may be accessed in this mode.

BRIGHT

In this mode:

- The IRIS opening time is fixed to 1/50 second.

- The auto IRIS opening is manually varied in the “BRIGHT

LEVEL” menu.

- Gain control is off (0 dB).

LOW LIGHT MODE

AUTO/MANUAL

This parameter is as follows:

- AUTO: uses a fixed maximum IRIS opening (1/50 second).

- MANUAL: increases camera sensitivity to the detriment of

refreshing frequency (frame rate) using the “LOW LIGHT LIMIT” value.

These adjustments are possible only in “MANUAL” or “SHUTTER” mode.

LOW LIGHT LIMIT

1/2, 1/3, 1/6, 1/12, 1/25, 1/50, 1/75, 1/100, 1/120, 1/150, 1/215, 1/300, 1/425, 1/600, 1/1000, 1/1250, 1/1750, 1/2500, 1/3500, 1/6000, 1/10000 OF

SECOND

This selects the maximum opening of the IRIS. It is used to manually set the IRIS opening time.

These adjustments are possible only in “MANUAL” or

“SHUTTER” mode.

IRIS LEVEL

F2.0, F1.6, F1.4, OFF, F22, F19, F16, F14, F11, F 9.6, F8.0, F6.8, F5.6, F4.8, F4.0, F3.4,

F2.8, F2.4

Manual IRIS adjustment (parameter F). It is used to manually set the IRIS opening time.

These adjustments are possible only in “MANUAL” or “IRIS” mode.

AGC LEVEL

-3DB, 0DB, 2 DB, 4 DB, 6DB, 8 DB, 10 DB, 12 DB, 14 DB, 16 DB, 18 DB, 20 DB, 22 DB, 24

DB, 26 DB, 28 DB

It is possible to automatically control gain (AGC) to one of the indicated values.

This selection is used to manually set the video signal gain. These adjustments are possible only in “MANUAL” mode.

BRIGHT LEVEL

0DB ~ 28DB

This function adjusts the camera gain and the IRIS opening using a special algorithm which may be programmed by the user. Exposure is controlled by the gain in low light condition and by the IRIS opening in bright light conditions.

The function may be used only if “AE MODE” is set to

“BRIGHT”.

SPOT AE

ON/OFF

If this function is on, the adjustments only use the middle part of the image.

Table 6

 The following items cannot be accessed in if “AE MODE” is set to “AUTO”:

 LOW LIGHT MODE (fixed to “MANUAL”)

21 / 43

 LOW LIGHT LIMIT  IRIS LEVEL  AGC LEVEL  BRIGHT LEVEL

ADDITIONAL sub-menu - Other program settings.

ADDITIONAL

IR SW MODE AUTO IR STATUS COLOR AUTO IRIS ON SHARPNESS ON SHARPNESS LEVEL 5 AUTO WHITE BALANCE AUTO R GAIN 214 B GAIN 164 BACK

Screen 9: Additional Sub-Menu

Option

Value

Explanation

IR SW MODE

AUTO/MANUAL

The opening and closing of the IR filter which adjusts the Day & Night vision of the camera may be controlled in MANUAL mode. The MANUAL option enables the possibility to adjust the IR STATUS parameter (color, B/W). In AUTO mode, the switch is automatic according to the lighting.

IR STATUS

COLOR, B/W

Day & Night camera configuration.

AUTO IRIS

ON/OFF

The auto IRIS may operate automatically (ON) or at a predetermined level in the “IRIS LEVEL” menu. If enabled manually, this function will remain operative until the camera performs an angular movement of less than 15 degrees. It will switch automatically.

SHARPNESS

ON/OFF

The sharpness of the image may be adjusted automatically (ON) or to a level defined in the

“SHARPNESS LEVEL” menu.

SHARPNESS LEVEL

0 ~ 15

Sharpness can be programmed in the range from 1 to 15 (15 corresponds to maximum sharpness).

AUTO WHITE BALANCE

ATW

White Balance (WB) is performed in auto tracking mode (Auto Tracking White). This mode automatically balances the white level by analyzing a wide range of colors, i.e. all those with temperatures comprised in the range between 2000K and 10000K.

AUTO

This mode automatically adjusts the white balance by analyzing a more restricted range with respect to the previous option i.e. those with temperatures in the range from 3000K and 7500K.

OUT

This function automatically balances the whites for outdoor use.

IN

This function automatically balances the whites for indoor use.

MAN

In this mode, white balancing may be performed by manually selecting the amount of red (R GAIN) and blue (B GAIN).

R GAIN

0 ~ 255

Adjust the red components using these values.

B GAIN

0 ~ 255

Adjust the blue components using these values.

Table 7

4.5.3.2. MOTION

22 / 43

MOTION

AUTO FLIP ON PROPORTIONAL PAN ON PARK TIME 15S PARK ACTION NONE SCAN SPEED<DEG/S> 1 <SET SCAN> <MANUAL LIMIT> <SET AZIMUTH ZERO> <CLEAR AZIMUTH ZERO> BACK

Screen 10: Motion Sub-Menu

Option

Value

Explanation

AUTO FLIP

ON/OFF

When this option is on, the movements of a subject moving underneath the camera can be followed by moving the joystick vertically only. This is possible because after reaching vertical position, the camera will automatically pan by 180 degrees to be repositioned and resume the tilt stroke.

PROPORTIONAL PAN

ON/OFF

If this mode is active, the pan and tilt speed applied by the keypad is proportional to the set zoom so that the movement speed decreases when the zoom increases.

PARK TIME

15 S ~ 12 H

With this function, the camera will resume the function defined in ”PARK ACTION” by specifying a value (in 1s, 1m, 1h steps) following a stop or interruption of the performed function after the programmed time.

PARK ACTION

NONE

No action is performed at the end of the park time.

AUTO SCAN

The camera performs an auto scan at the end of the park time: the camera performs a 360 horizontal scan operation.

RANDOM SCAN

The camera performs a random scan at the end of the park time: the camera performs a random 360 degree scan pausing for approximately 2” every 142°.

FRAME SCAN

The camera performs a frame scan at the end of the park time: the horizontal scan is performed in the

SET SCAN

limits.

PRESET 1/PRESET 8

The camera goes to preset 1 or preset 8 at the end of the park time.

PATTERN 1 ~ 4

The camera performs one of the 4 patterns at the end of the park time (command sequence continuously performed).

CRUISE

The camera performs a cruise (preset sequence) at the end of the park time: the camera runs a cycle of up to 30 preset positions.

REPEAT LAST

The camera simply resumes the operation it was performing before being interrupted at the end of the park time.

HOME N TRA

The camera goes to preset 1 and starts tracking at the end of the park time.

CRUISE TRA

The camera performs a cruise with tracking on at the end of park time.

SCAN SPEED <DEG/S>

1 ~ 32 DEG./S

This will specify the rotation speed for automatic horizontal scans.

SET SCAN

This submenu set the limits for horizontal pan movements of the camera. The limits are long applicable in FRAME SCAN mode (see below).

MANUAL LIMIT

ON/OFF

If this option is ON, horizontal automatically scanning is performed within the right and left scanning limits open.

To set the left and right scanning limit, position the camera at the required pan angle and press OPEN to set.

A preset position may be called up outside these scanning limits.

SET AZIMUTH ZERO

This sets the pan zero position (see below).

CLEAR AZIMUTH ZERO

This is used to delete the zero position settings (see below).

23 / 43

Table 8

SET SCAN submenu

This includes a number of settings related to the programming of horizontal FRAME SCAN limits.

1) Press “►” on “SET SCAN STOPS”.

2) Press OPEN to confirm.

3) Go to the required position with the joystick to set the left scanning limit.

4) Press OPEN to confirm.

5) Go to the required position with the joystick to set the right scanning limit.

6) Press OPEN to confirm, Press CLOSE to cancel the operation.

7) Point the cursor “►” to “CLEAR SCAN STOPS” and press OPEN to delete the programmed positions. SET AZIMUTH ZERO submenu

This includes the settings related to programming of the pan zero position.

1) Go to the required position with the joystick to set zero position.

2) Press OPEN to confirm; Press CLOSE to cancel the operation. CLEAR AZIMUTH ZERO submenu

This includes the settings related to deleting the pan zero position.

1) Press OPEN to confirm.

2) Press CLOSE to cancel the operation.

4.5.3.3. POWER UP

POWER UP

POWER UP ACTION NONE BACK EXIT

Screen 11: Power UP Sub-Menu

Option

Value

Explanation

POWER UP ACTION

NONE

No action is performed at the end of power up.

AUTO SCAN

The camera performs an auto scan at the end of power up: the camera performs a 360 horizontal scan operation.

RANDOM SCAN

The camera performs a random scan at the end of power up: the camera performs a random 360° scan pausing for approximately 2” every 142°.

FRAME SCAN

The camera performs a frame scan at the end of power up: the horizontal scan is performed in the SET SCAN limits.

PRESET 1/ PRESET 8

The camera goes to preset 1 or 8 at the end of power up.

PATTERN 1 ~ 4

The camera performs one of the 4 patterns at the end of power up.

CRUISE

The camera performs a cruise at the end of power up: the camera runs a cycle consisting of up to 30 preset positions.

HOME N TRA

The camera goes to preset 1 and starts tracking at the end of power up.

CRUISE TRA

The camera performs a cruise with tracking on at the end of power up.

Table 9

4.5.3.4. PRESETS

 The camera will start a scannin g cycle when a presetting or pattern is recalled. This scanning cycle may be

interrupted simply by moving the joystick.

24 / 43

PRESETS

PRESET NUMBER 1 …PRESET NOT DEFINED… <EDIT PRESET LABEL> <EDIT PRESET POSITION> <CLEAR CURRENT PRESET> BACK EXIT

Screen 12: Presets

Option

Value

Explanation

PRESET NUMBER

1-64

This option is used to select a presetting for entering a descriptive label. This operation is allowed for up to 64 presets.

Press the OPEN button and use the joystick to set the number of the presetting to be stored. Press OPEN to confirm.

EDIT PRESET LABEL

This submenu is used to access writing mode for associating a label to a presetting (see below).

EDIT PRESET POSITION

This submenu is used to position and save the current position.

CLEAR CURRENT PRESET

The submenu is used to delete the current preset.

Table 10

EDIT PRESET LABEL submenu

This includes the operations needed for associating a label to a presetting.

1) Use the joystick to point the cursor to ”EDIT PRESET LABEL” option.

2) Press OPEN. The following menu will appear on the display:

PRESET NUMBER 1

PRESET LABEL 1 - - - - 0 1 2 3 4 5 6 7 8 9 Y Z y z A B C D E F G H I J K L M N O P Q R S T U V W X a b c d e f g h I j k l m n o p q r s t u v w x OK CANCEL

SPACE BACKSPACE`

Screen 13: Preset Label Sub-Menu

3) Point the cursor to the first character to use and press OPEN. Point the cursor to “BACKSPACE” to delete it.

4) After writing the text, point the cursor to OK and press OPEN to save and go back to the main screen.

4.5.3.5. PATTERNS

PATTERNS

PATTERN NUMBER 1 <PROGRAM PATTERN> <CLEAR CURRENT PATTERN> BACK EXIT

Screen 14: Patterns Sub-Menu

A pattern is a sequence of movements and functions which may be stored and repeated manually or automatically.

Option

Value

Explanation

PATTERN NUMBER

1 ~ 4

This option is used to select a pattern.

PROGRAM PATTERN

This submenu is used to program a pattern (see below)

CLEAR CURRENT PATTERN

This submenu is used to delete current pattern.

Table 11

PROGRAM PATTERN submenu

This includes all the operations needed to program a pattern.

1) Use the joystick to point the cursor to the ”PATTERN NUMBER” option.

25 / 43

2) Select the required pattern and press OPEN.

3) Position the cursor under ”PROGRAM PATTERN” option and press the OPEN button. The number of actions available (including zoom operations) for programming the Pattern is shown in percentage form on

the screen while they are each being programmed. 100 operations are available for each pattern.

4.5.3.6. ZONES

ZONES

ZONE NUMBER 1 …ZONE NOT DEFINED… <EDIT ZONE LABEL> <EDIT ZONE> ENABLE ZONE ON <CLEAR CURRENT ZONE > BACK EXIT

Screen 15: ZONES Sub-Menu

A zone is a space defined on the display by the user. It may be associated to a label. Up to 8 zones may be defined.

Option

Value

Explanation

ZONE NUMBER

1 ~ 8

This option is used to select a zone. Press the OPEN button and use the joystick to set the

required zone number. Press OPEN to confirm.

EDIT ZONE LABEL

This submenu is used to associate a label to a zone (see below).

EDIT ZONE

This submenu is used to create a zone (see below).

ENABLE ZONE

ON/OFF

This is used to enable/disable each zone selected in the

“ZONE NUMBER” field.

CLEAR CURRENT ZONE

This submenu is used to delete the zone selected in the “ZONE NUMBER” field (see below).

Table 12

EDIT ZONE LABEL submenu

This includes the operations needed to enter labels to be associated to zones.

1) Use the joystick to point the cursor to the ”EDIT ZONE LABEL” option.

2) Press OPEN. The following menu will appear on the display:

ZONE NUMBER 1

ZONE LABEL 1 - - - - 0 1 2 3 4 5 6 7 8 9 Y Z y z A B C D E F G H I J K L M N O P Q R S T U V W X a b c d e f g h I j k l m n o p q r s t u v w x OK CANCEL

SPACE BACKSPACE

Screen 16: Zone Label Sub-Menu

3) Point the cursor to the first character to be used and press OPEN. Point the cursor to “BACKSPACE” to delete it.

4) After writing the text, point the cursor to OK and press OPEN to save and go back to the main screen. EDIT ZONE submenu

This includes all the operations needed to program a zone.

1) Press “►” on “EDIT ZONE”.

2) Press OPEN to confirm.

3) Use the joystick to point to the required position to define the left limit of the zone to be created.

4) Press OPEN to confirm. Press CLOSE to cancel the operation.

5) Use the joystick to point to the required position to define the right limit of the zone to be created.

6) Press OPEN to confirm. Press CLOSE to cancel the operation.

7) Press CLOSE to cancel the operation.

4.5.3.7. CLEAR SET

26 / 43

CLEAR SET

CLEAR ZONES CLEAR PRESETS CLEAR PATTERNS RESTORE FACTORY DEFAULT BACK EXIT

Screen 17: Clear Set Sub-Menu

This menu is used to delete the settings of several elements at one time.

Option

Value

Explanation

CLEAR ZONES

This option is used to delete all the zone settings.

CLEAR PRESETS

This is used to delete all the Presets.

CLEAR PATTERNS

This is used to delete all the pattern settings.

RESTORE FACTORY

DEFAULT

This performs a total reset and loads the default settings. The operations may take a few seconds (approximately 20 seconds): the message “WAIT” will appear on the monitor.

Table 13

4.5.3.8. PRESET NUMBER

This option can be used to set the number of Presets which may be used.

1) Point the cursor to “►” “PRESET NUMBER”.

2) Press ENTER.

3) Move the joystick vertically and select “256”.

4) Press ENTER to confirm.

 Do not change the setting (“256”).

4.5.4. SECONDARY PROGRAMMING MENU (DOME SETTINGS 2)

In the first level menu, select <DOME SETTINGS 2> and the corresponding submenus to access the other menus.

DOME SETTINGS 2

<ALARMS> <ADDR SETTING> <PASSWORD> <WINDOWS BLANKING> <HEATER SETTING> <CRUISE SETTING> <TRACKING SETTING> BACK EXIT

Screen 18: Dome Settings 2

Option

Value

Explanation

ALARMS

Alarm submenu (refer to Section 4.5.4.1)

ADDR SETTING

Address setting submenu (refer to Section 4.5.4.2)

PASSWORD

Password submenu (refer to Section 4.5.4.3)

WINDOWS BLANKING

Windows blanking submenu (refer to Section 4.5.4.4)

HEATER SETTING

Heater use submenu (refer to Section 4.5.4.5)

CRUISE SETTING

Cruise programming submenu (refer to Section 4.5.4.6)

TRACKING SETTING

Automatic tracking submenu (refer to Section 4.5.4.7)

Table 14

4.5.4.1. ALARMS

27 / 43

ALARMS

ALARM NUMBER 1 SEQUENCE(SECS) 1 ALARM ACT CRUISE ACTIVATE AUX OFF <CLEAR SET> DWELL TIME<SECS>1 0 DWELL TIME<SECS>2 0 BACK EXIT

Screen 19: Alarms Sub-Menu

The camera has 4 alarm inputs and 2 alarm outputs. The actions defined by the user may be associated to an alarm.

Option

Value

Explanation

ALARM NUMBER

1 ~ 4

This option allows selecting one of the 4 alarm inputs.

SEQUENCE (SECS)

1 ~ 250

Duration time (in seconds) of the action related to each alarm when several alarms occur at the same time.

ALARM ACT

NONE

No action is performed on alarm.

AUTO SCAN

The camera performs an auto scan on alarm: the camera performs a 360 horizontal scan operation.

RANDOM SCAN

The camera performs a random scan on alarm: the camera performs a random 360° scan pausing for approximately 2” every 142°.

FRAME SCAN

The camera performs a frame scan on alarm: the horizontal scan is performed in the SET SCAN limits.

PRESET

The camera goes to related preset on alarm.

PATTERN 1

The camera performs pattern action 1 on alarm.

PATTERN 2

The camera performs pattern action 2 on alarm.

PATTERN 3

The camera performs pattern action 3 on alarm.

PATTERN 4

The camera performs pattern action 4 on alarm.

CRUISE

The camera performs a cruise on alarm: the camera runs a cycle consisting of up to 30 preset positions.

TRACKING

The camera performs tracking action on alarm.

PRESET N TRA

The camera goes to related preset and starts tracking function.

CRUISE TRA

The camera performs a cruise with tracking on alarm.

ACTIVATE AUX

OFF

No action occurs after the alarm.

1

Output 1 is on.

2

Output 2 is on.

CLEAR SETTINGS

This submenu is used to delete the alarm programming (see below).

DWELL TIME<SECS>1

0 ~ 255

The duration of related alarm output

DWELL TIME<SECS>2

0 ~ 255

The duration of related alarm output

Table 15

 If an alarm is triggered during any automatic operation of the camera (Pattern, Auto Tracking, etc.), the operation

in progress is stopped and the camera executes the action that has been set in the ALARM ACT menu:

 In the event of Preset action, the camera moves to the preset position. Then, if the option PARK ACTION is

set to execute an action, the action will be executed after the PARK TIME period has expired.

 In the event of "PATTERN, AUTO SCAN, RANDOM SCAN, FRAME SCAN, CRUISE" actions, the action is

executed by the camera permanently and can only be stopped by one of the following actions: any command sent by a controller or any alarm event.

4.5.4.2. ADDR SETTING

28 / 43

ADDR SETTING

ADDR TYPE HARD ADDR SOFT 255 ADDR HARD 0 BACK EXIT

Screen 20: Alarm Settings

The soft address is the address programmed by built-in software. The hard address is the address programmed by the hardware SWITCH 2.

Option

Value

Explanation

ADDR TYPE

SOFT, HARD

This option is used to program the type of address in current application.

Press the OPEN button and use the joystick to select the value. Press OPEN to confirm.

ADDR SOFT

0~255

The option is used to change the soft address.

ADDR HARD

This option shows the hard address number. It is the address of the SW2 (Switch Setting 2).

Table 16

 The camera needs a reboot for the new address to take effect. When the hard address is different from that of

last power up, the hard address will be applicable and the camera address will be hard type.

4.5.4.3. PASSWORD

PASSWORD

ENABLE PASSWORD OFF <EDIT PASSWORD> BACK EXIT

Screen 21: Password Sub-Menu

Option

Value

Explanation

ENABLE PASSWORD

ON/OFF

This enables the password.

EDIT PASSWORD

This is the password entry procedure.

Table 17

The password is a numeric combination (max. 10 digits).

 The default password is “0000”.  It is advisable to change the default password to prevent intrusions.  Do not lose or forget the programmed password.  Take note of the new password and keep it in a safe place.

INPUT OLD PASSWORD

PASSWORD 1 2 3 4 5 6 7 8 9 0

CLEAR ENTER BACK

Screen 22: Edit Password

1) Select the password digits by moving the joystick in the horizontal direction. Symbol “▲” indicates the digit which will be entered.

2) Press OPEN to enter the selected digit.

3) The entered numbers will be replaced by a “*” symbol on the screen for privacy.

29 / 43

4) Enter all the digits correctly and select ENTER to confirm.

5) During the password change procedure you will be asked to enter the old password. Enter the new password and enter it again for confirmation.

4.5.4.4. WINDOWS BLANKING

 Windows blanking is only available for Sony Modules at present.

The camera can be used to define up to eight privacy zones which blank out certain areas of the screen concealing them from the operator’s sight.

A privacy zone appears as a grey or black rectangle associated to a certain pan, tilt and zoom position of a camera. This association is used to move, expand and compress the rectangle according to how the pan, tilt or zoom settings are changed.

WINDOWS BLANKING

STYLE GRAY BLANK ALL ABOVE OFF BLANK ALL BELOW OFF <SET WINDOWS> SET MASK COLOR 4 BACK EXIT

Screen 23: Windows Blanking

Option

Value

Explanation

STYLE

GRAY/SMEAR

There are two ways to blank out the zone to be masked: either using a grey window which entirely conceals the area or by using a semi-transparent smear window which shows the scene without details.

BLANK ALL ABOVE

OFF, 0~80

Blanks out the upper part of the frame shown on the monitor. The value means the beginning degree of the vertical position.

BLANK ALL BELOW

OFF, 0~80

Blanks out the lower part of the frame shown on the monitor. The value means the beginning degree of the vertical position.

SET WINDOWS

The submenu is used to position and configure the privacy zones (see below).

SET MASK COLOR

0 ~ 13

This is used to select the blanking window color: 0 → black 1 ~ 6 → grey (1 dark; 6 light) 7 → white 8 → red 9 → green 10 → blue 11 → cyan 12 → yellow 13 → magenta

Table 18

 The two blanking bands (upper & lower) may coexist at the same time.  The two blanking bands (upper & lower) cannot coexist at the same time in presence of a privacy zone.  A band will automatically be removed if both bands are enabled and a privacy zone is activated.  If an attempt to activate a blanking band is attempted with a privacy zone active, the p rivacy zone will remain

active to the detriment of the blank.

Blanking parameters

BLANK ALL ABOVE

BLANK ALL BELOW

OFF

No blanking

OFF

No blanking

0

-5º~10º

0

5º~92º

10

-5º~25º

10

-5º~92º

20

-5º~35º

20

5º~92º

30 / 43

30

-5º~45º

30

15º~92º

40

-5º~55º

40

25º~92º

50

-5º~65º

50

35º~92º

60

-5º~75º

60

45º~92º

70

-5º~85º

70

55º~92º

80

-5º~95º

80

70º~92º

Table 19 The coordinates shown on the monitor refer to the central point of the monitor (where the diagonals meet). SET WINDOWS submenu

This includes the operations needed to position and configure the privacy zones.

SET WINDOWS

WINDOWS NUMBER 1 <EDIT WINDOW LOCATION> <EDIT WINDOW ZOOM > ENABLE WINDOW OFF CLEAR CURRENT WINDOW BACK EXIT

Screen 24: Set Windows Sub-Menu

Option

Value

Explanation

WINDOWS NUMBER

1~ 8

This option is used to select one of the 8 privacy zones (WINDOWS).

EDIT WINDOW LOCATION

This option is used to activate the privacy zone positioning procedure (see below).

EDIT WINDOW ZOOM

This option sets the zoom level over which the created privacy zone will be visible.

ENABLE WINDOW

ON/OFF

This switches the privacy zone selected in WINDOW NUMBER on and off.

CLEAR CURRENT WINDOW

This deletes the privacy zone selected in WINDOW NUMBER.

Table 20 EDIT WINDOW LOCATION submenu

This menu may be used to define the position of the privacy zones to be created.

1) Press “►” on “EDIT WINDOW LOCATION”.

2) Press OPEN. The following screen will appear.

EDIT WINDOW LOCATION

IRIS OPEN TO CONTINUE IRIS CLOSE TO CANCEL

Screen 25: Edit Window Location Sub-Menu

3) A cross-shaped pointer will appear on the monitor: this pointer will correspond to the middle of the privacy zones

being created.

4) Point the cross-shaped cursor to the required position by moving the joystick in the vertical and horizontal directions.

5) Press OPEN. A square will appear on the monitor (with the previously defined features).

6) Use the joystick to obtain the required dimensions of the privacy zone:

a) Move leftwards to increase the left and right edges of the blanking zone b) Move rightwards to decrease the left and right edges of the blanking zone c) Move upwards to increase the upper and lower edges of the blanking zone d) Move downwards to decrease the upper and lower edges of the blanking zone

7) Press OPEN to confirm after reaching the required dimensions.

8) At this point, either select a new privacy zone or select CLOSE to quit the menu.

 It is preferable to set the privacy zones with a zoom level of 1x.

Remarks on Privacy Zones

31 / 43

 Privacy zones can be programmed (and therefore the menu can be opened) in optical zoom

situations only. The privacy zone works also in digital zoom conditions.

 The privac y zone rectangle will move on the screen when panning and tilting. Zooming will expand

and contract the rectangle.

 The rectangle will expand twice in the vertical direction and four times in the horizontal position to

avoid viewing protected areas when panning, tilting and zooming.

 After panning and tilting, the privacy zone rectangle will shift and return to the correct dimensions.

After zooming, the rectangle will remain either contracted or expanded according to the applied zoom (regardless of the x2 or x4 factor applied while zooming).

 It is advisable to make the privacy areas slightly larger than the area to be concealed.  Privacy zones can only be rectangular or squares, but several rectangles can be placed to mask the

area as required.

EDIT WINDOW ZOOM submenu This menu item is used to define the zoom level at which the privacy zone becomes visible after defining the color and the position of the privacy zone.

1) Press “►” on “EDIT WINDOW ZOOM”.

2) Press OPEN, the following screen will appear.

EDIT WINDOW ZOOM

IRIS OPEN TO CONTINUE IRIS CLOSE TO CANCEL

Screen 26: Edit Window Zoom

3) Press OPEN and start the zoom setting procedure. The newly created privacy zone will appear on the monitor.

4) Use the joystick to obtain the required zoom level over which the privacy zone will become visible: a) Turn clockwise to increase the zoom level b) Turn anticlockwise to decrease the zoom level

5) Press OPEN to confirm.

4.5.4.5. HEATER SETTING

HEATER SETTING

HEATER DISPLAY ON HEATER MODE AUTO

TEMPERATURE SET 33℃

BACK EXIT

Screen 27: Heater Setting

Option

Value

Explanation

HEATER DISPLAY

ON/OFF

This switches the heater status display on and off. The message “HEATER” will appear when the heater is on.

HEATER MODE

AUTO

Heater operating mode: when set to ”AUTO”, the heater is operated when the outside temperature is lower than the setting made in the following menu.

OFF

The heater is always off.

ON

The heater is always on.

TEMPERATURE SET

-99 ~ +99

Temperature threshold in °C under which the heater is activated. Recommended values 18 - 20 °C

Table 21

4.5.4.6. CRUISE SETTING

32 / 43

CRUISE

DWELL TIME<SECS> 7 PRESET LIST 1

1 ON 0 OFF 1234567890 <PRESET 1-10> 0110010111 BACK EXIT

Screen 28: Cruise

The CRUISE function is used to make the camera run a cycle consisting of up to 30 preset positions. This menu item is used to enable each of the preset positions used in the cruise cycle.

For the cruise cycle to be effective, the preset positions must be actually stored.

Option

Value

Explanation

DWELL TIME <SECS>

5 ~ 250

Duration (in seconds) of the dwelling time on each presetting.

PRESET LIST

1 ~ 3

Value 1 selects the first group of Presets from 1 to 10, value 2 selects the second group from 11 to 20, value 3 the third group from 21 to 30.

The following 10 digits (1/10) are used to switch the corresponding preset in the corresponding ten (1-10, 11-20, 21-30) either on or off (1=ON; 0=OFF).

Table 22

4.5.4.7. TRACKING SETTING

TRACKING SETTING

DEFAULT SETTING SIZE SENS MEDIUM GRAY SENS MEDIUM LOST ACT STOP TRACK ZOOM SETTING ON WAIT TIME<S> 40 <TRACKING BOUNDARY> AUX OFF TRACKING SPEED

AUTO TRACKING TIME<M> AUTO BACK

Screen 29: Tracking Setting Sub-Menu

The auto tracking function is used to automatically track moving objects by detecting grayscale variations in the frame.

Option

Value

Explanation

DEFAULT SETTING

This function is used to load the auto tracking default settings.

SIZE SENS

LARGE/MEDIUM/SMAL

L

This option defines the total dimensions of the object to be tracked. The parameters are LARGE/MEDIUM/SMALL. An object larger than one fourth of the screen is LARGE. An object smaller than one eighth of the screen is SMALL.

GRAY SENS

HIGH/MEDIUM/LOW

This option determines the auto tracking sensitivity. The sensitivity measures the grey scale variations of a certain point in the frame in the unit of time.

LOST ACT

HOME N TRA

This option is used to establish the action to be performed if the camera loses the tracked object: the HOME N TRA

option goes to preset 1 and starts tracking.

KEEP TRACK

The KEEP TRACK option keeps the camera in the position reached and the tracking function is kept on waiting for an object to be intercepted again.

STOP TRACK

The STOP TRACK option leaves the camera in the position reached and deactivates the tracking function.

33 / 43

ZOOM SETTING

OFF, 1 ~ 18

This option determines the maximum zoom value that the camera may use for tracking the object.

WAIT TIME

5, 10, 15, 20, 25,

30, 35, 40 SECONDS

This op tion determines the time which must elapse before performing Lost Act after losing a motion in frame.

TRACKING BOUNDARY

UP/DOWN/LEFT/RIGH

T

This option is used to define the zone in which the camera performs the tracking.

AUX OFF, 1, 2

This option is used to activate one of the 2 alarm outputs if the tracking function is on (OFF = no active alarm output).

TRACKING SPEED

AUTO, 1 ~ 63

This option establishes the camera movement speed. If AUTO is selected, the camera is automatically “adapted” to the motion of the target. The 1~63 options allow selecting the expected speed of the object to be tracked (1 slow, 63 fast).

TRACKING TIME

AUTO,1~15

(MINUTES)

This option allows setting the max. tracking duration, in minutes, during which the camera automatically tracks moving objects.

Once the tracking time has expired, the camera exits the tracking mode, waiting for further commands

Table 23

TRACKING BOUNDARY submenu

Operations needed to establish an intervention zone for the tracking function.

TRACKING BOUNDARY

BOUNDARY LIMIT OFF CLEAR BOUNDARY LEFT LIMIT OFF RIGHT LIMIT OFF UP LIMIT OFF DOWN LIMIT OFF BACK EXIT

Screen 30: Tracking Boundary Sub-Menu

Option

Value

Explanation

BOUNDARY LIMIT

ON/OFF

This switches tracking function intervention zone on and off.

CLEAR BOUNDARY

This deletes the intervention area.

LEFT LIMIT

ON/OFF

Left limit of the intervention zone.

RIGHT LIMIT

ON/OFF

Right limit of the intervention zone.

UP LIMIT

ON/OFF

Up limit of the intervention zone.

DOWN LIMIT

ON/OFF

Low limit of the intervention zone.

Table 24

Advice for Correct Auto Tracking Use

34 / 43

General warnings

 The tracking function should mainly be used in indoor environments.  Provide the best lighting possible in the detection zone: in poor lighting conditions, the inevitable

presence of noise on the image makes grayscale variations extremely critical. In poor lighting conditions, the camera may easily lose the tracked object.

 If IR illuminators are used, remember that:

 The camera must be programmed to operate in B/W only (DOME SETTINGS 1 > CAMERA >

ADDITIONAL menu) because the Slow Shutter will make tracking unreliable in color mode

 The lighting entirely covers the frame where motion is tracked, possibly by restricting the range of

action of the camera in tracking mode (using the TRACKING BOUNDARY option).

 Avoid background objects in the frame which could trick the motion detector, such as for example

Venetian blinds, gates, doors with grid and objects with very marked, contrasting contours. A chequerboard background is certainly the worst condition for satisfactory operation.

 Do not use the privacy zone function in frames where auto tracking is used: the privacy zone can trick

the auto tracking function.  Do not use the auto tracking function if the object to be tracked and/or monitored moves too fast. Recommended control parameters

SIZE SENS: select SMALL particularly in poor lighting conditions to improve performance. GRAY SENS: most false alarms are caused by the tracking of unexpected objects. For this reason, it is

preferable to select low sensitivity.

ZOOM SETTING: it is advisable to use the lowest possible zoom values. WAIT TIME: particularly, in the case of poor lighting conditions or frames with interference, it is preferable to

set the lowest possible time to prevent the camera from constantly tracking unexpected objects (e.g. “video noise” in the frame).

TRACKING SPEED: the AUTO setting should always be preferred, unless the object to be tracked does not always move at low, constant speed.

TRACKING BOUNDARY: it is strongly advised to delimit the tracking zone, avoiding including unnecessary parts in the frame.

 Tracking during cruise is available. When the camera is cruising among saved presets, it will detect and follow

moving object automatically when it stops at a specific preset. When the moving object gets out of view for pre-defined interval, the camera will go back to its previously stopped preset and cruise to the next preset again.

 Enter DOME SETTINGS 1 > MOTION > PARK ACTION, set it as REPEAT LAST  Go to DOME SETTINGS 2 > TRACKING SETTING > LOST ACT, set it as STOP TRACK  Go to DOME SETTINGS 2 > CRUISE > DWELL TIME, set it as 8 and program the preset list  PRESET + 92 + ENTER to start the function.

4.5.5. DOME LABEL

DOME LABEL

<EDIT DOME LABEL> <CLEAR DOME LABEL> BACK EXIT

Screen 31: Dome Label Menu

Option

Value

Explanation

EDIT DOME LABEL

This submenu is used to access writing mode for associating a camera label (see below).

35 / 43

CLEAR DOME LABEL

This submenu allows deleting the label associated to the camera (see below).

Table 25

EDIT DOME LABEL submenu

The operations needed to associate a label to a camera are:

1) Use the joystick to point the cursor to the ”EDIT DOME LABEL” option.

2) Press OPEN. The following menu will appear on the display:

DOME LABEL

EDIT DOME LABEL

0 1 2 3 4 5 6 7 8 9 Y Z y z A B C D E F G H I J K L M N O P Q R S T U V W X a b c d e f g h I j k l m n o p q r s t u v w x OK CANCEL

SPACE BACKSPACE

Screen 32: Edit Dome Label

3) Point the cursor to the first character to be used and press OPEN. Point the cursor to “BACKSPACE” to delete it.

4) After writing the text, point the cursor to OK and press OPEN to save and go back to the main screen.

4.6. SPECIAL CONTROL PANEL COMMANDS

The camera can be programmed and operated using various quick control panel commands.

Control panel command

Function

PRESET + 95 + ENTER

Access main menu

PRESET + XXX + ENTER

Store preset position (Preset) xxx.

CALL + XXX + ENTER

Recall preset position (Preset) xxx.

CALL + 80 + ENTER

Start the tracking function

CALL + 82 + ENTER

Start the cruise function

CALL + 83 + ENTER

Delete all Presets

PRESET + 84 + ENTER

Store pattern 1

PRESET + 85 + ENTER

Store pattern 2

PRESET + 86 + ENTER

Store pattern 3

PRESET + 87 + ENTER

Store pattern 4

CALL + 84 + ENTER

Start pattern 1

CALL + 85 + ENTER

Start pattern 2

CALL + 86 + ENTER

Start pattern 3

CALL + 87 + ENTER

Start pattern 4

CALL + 88 + ENTER

Start park action function

CALL + 89 + ENTER

Stop park action function

CALL + 92 + ENTER

Start cruise with tracking function activated

CALL + 93 + ENTER

Call the menu of boundary setting

CALL + 94 + ENTER

Start/Stop wide dynamic range function

CALL + 97 + ENTER

Start random scan function

CALL + 98 + ENTER

Start frame scan function

CALL + 99 + ENTER

Start auto scan function

Table 26

 When storing Presets, it is important to remember that some are reserved and cannot be either stored or used for

positioning the camera. Presets from 80 to 99, Presets from 100 to 103, 170 to 173.

36 / 43

5. TROUBLE SHOOTING

Problem

Possible Reason

Solution

Power on normally but no video signal

Wrong wire connections

Check and reconnect wires

Wrong or bad power source

Change power source

Fuse broken.

Change fuse

Power cable is disconnected

Reconnect power wiring

Pan/Tilt not initializing when power on

Address, protocol, and baud rate is not correctly set

Check and set the parameters again.

RS485 cable is not correctly connected

Check and reconnect RS485 cable

Video is not stable

Video cable is wrong

Check and reconnect video

Power source is wrong

Change the power source

Control center is not stable

RS485 wiring error

Check and reconnect the RS485

Table 27

37 / 43

6. ANNEX

6.1. DIP SWITCH CHART

POS

1 2 3 4 DESCRIPTION

COMM PTOL

ON

OFF

USER

OFF

ON

OFF

PELCO-P

ON

OFF

PELCO-D

OFF

ON

OFF

DAHUA

POS

DESCRIPTION

5 6 7

8

BAUD RATE (BPS)

1200

ON

OFF

2400

OFF

ON

OFF

4800

ON

OFF

9600

OFF

ON

OFF

19200

ON

OFF

ON

OFF

Reserved for future use

…

Table 28: SWITCH1 SETTING

ADDRESS

1 2 3 4 5 6 7

8

0

OFF

1

ON

OFF

2

OFF

ON

OFF

3

ON

OFF

4

OFF

ON

OFF

5

ON

OFF

ON

OFF

6

OFF

ON

OFF

7

ON

OFF

8

OFF

ON

OFF

9

ON

OFF

ON

OFF

10

OFF

ON

OFF

ON

OFF

11

ON

OFF

ON

OFF

12

OFF

ON

OFF

13

ON

OFF

ON

OFF

14

OFF

ON

OFF

15

ON

OFF

16

OFF

ON

OFF

17

ON

OFF

ON

OFF

18

OFF

ON

OFF

ON

OFF

19

ON

OFF

ON

OFF

20

OFF

ON

OFF

ON

OFF

21

ON

OFF

ON

OFF

ON

OFF

22

OFF

ON

OFF

ON

OFF

23

ON

OFF

ON

OFF

24

OFF

ON

OFF

25

ON

OFF

ON

OFF

26

OFF

ON

OFF

ON

OFF

27

ON

OFF

ON

OFF

28

OFF

ON

OFF

29

ON

OFF

ON

OFF

30

OFF

ON

OFF

31

ON

OFF

32

OFF

ON

OFF

38 / 43

33

ON

OFF

ON

OFF

34

OFF

ON

OFF

ON

OFF

35

ON

OFF

ON

OFF

36

OFF

ON

OFF

ON

OFF

37

ON

OFF

ON

OFF

ON

OFF

38

OFF

ON

OFF

ON

OFF

39

ON

OFF

ON

OFF

40

OFF

ON

OFF

ON

OFF

41

ON

OFF

ON

OFF

ON

OFF

42

OFF

ON

OFF

ON

OFF

ON

OFF

43

ON

OFF

ON

OFF

ON

OFF

44

OFF

ON

OFF

ON

OFF

45

ON

OFF

ON

OFF

ON

OFF

46

OFF

ON

OFF

ON

OFF

47

ON

OFF

ON

OFF

48

OFF

ON

OFF

49

ON

OFF

ON

OFF

50

OFF

ON

OFF

ON

OFF

51

ON

OFF

ON

OFF

52

OFF

ON

OFF

ON

OFF

53

ON

OFF

ON

OFF

ON

OFF

54

OFF

ON

OFF

ON

OFF

55

ON

OFF

ON

OFF

56

OFF

ON

OFF

57

ON

OFF

ON

OFF

58

OFF

ON

OFF

ON

OFF

59

ON

OFF

ON

OFF

60

OFF

ON

OFF

61

ON

OFF

ON

OFF

62

OFF

ON

OFF

63

ON

OFF

64

OFF

ON

OFF

65

ON

OFF

ON

OFF

66

OFF

ON

OFF

ON

OFF

67

ON

OFF

ON

OFF

68

OFF

ON

OFF

ON

OFF

69

ON

OFF

ON

OFF

ON

OFF

70

OFF

ON

OFF

ON

OFF

71

ON

OFF

ON

OFF

72

OFF

ON

OFF

ON

OFF

73

ON

OFF

ON

OFF

ON

OFF

74

OFF

ON

OFF

ON

OFF

ON

OFF

75

ON

OFF

ON

OFF

ON

OFF

76

OFF

ON

OFF

ON

OFF

77

ON

OFF

ON

OFF

ON

OFF

78

OFF

ON

OFF

ON

OFF

79

ON

OFF

ON

OFF

80

OFF

ON

OFF

ON

OFF

81

ON

OFF

ON

OFF

ON

OFF

82

OFF

ON

OFF

ON

OFF

ON

OFF

83

ON

OFF

ON

OFF

ON

OFF

39 / 43

84

OFF

ON

OFF

ON

OFF

ON

OFF

85

ON

OFF

ON

OFF

ON

OFF

ON

OFF

86

OFF

ON

OFF

ON

OFF

ON

OFF

87

ON

OFF

ON

OFF

ON

OFF

88

OFF

ON

OFF

ON

OFF

89

ON

OFF

ON

OFF

ON

OFF

90

OFF

ON

OFF

ON

OFF

ON

OFF

91

ON

OFF

ON

OFF

ON

OFF

92

OFF

ON

OFF

ON

OFF

93

ON

OFF

ON

OFF

ON

OFF

94

OFF

ON

OFF

ON

OFF

95

ON

OFF

ON

OFF

96

OFF

ON

OFF

97

ON

OFF

ON

OFF

98

OFF

ON

OFF

ON

OFF

99

ON

OFF

ON

OFF

100

OFF

ON

OFF

ON

OFF

101

ON

OFF

ON

OFF

ON

OFF

102

OFF

ON

OFF

ON

OFF

103

ON

OFF

ON

OFF

104

OFF

ON

OFF

ON

OFF

105

ON

OFF

ON

OFF

ON

OFF

106

OFF

ON

OFF

ON

OFF

ON

OFF

107

ON

OFF

ON

OFF

ON

OFF

108

OFF

ON

OFF

ON

OFF

109

ON

OFF

ON

OFF

ON

OFF

110

OFF

ON

OFF

ON

OFF

111

ON

OFF

ON

OFF

112

OFF

ON

OFF

113

ON

OFF

ON

OFF

114

OFF

ON

OFF

ON

OFF

115

ON

OFF

ON

OFF

116

OFF

ON

OFF

ON

OFF

117

ON

OFF

ON

OFF

ON

OFF

118

OFF

ON

OFF

ON

OFF

119

ON

OFF

ON

OFF

120

OFF

ON

OFF

121

ON

OFF

ON

OFF

122

OFF

ON

OFF

ON

OFF

123

ON

OFF

ON

OFF

124

OFF

ON

OFF

125

ON

OFF

ON

OFF

126

OFF

ON

OFF

127

ON

OFF

128

OFF

ON

129

ON

OFF

ON

130

OFF

ON

OFF

ON

131

ON

OFF

ON

132

OFF

ON

OFF

ON

133

ON

OFF

ON

OFF

ON

134

OFF

ON

OFF

ON

40 / 43

135

ON

OFF

ON

136

OFF

ON

OFF

ON

137

ON

OFF

ON

OFF

ON

138

OFF

ON

OFF

ON

OFF

ON

139

ON

OFF

ON

OFF

ON

140

OFF

ON

OFF

ON

141

ON

OFF

ON

OFF

ON

142

OFF

ON

OFF

ON

143

ON

OFF

ON

144

OFF

ON

OFF

ON

145

ON

OFF

ON

OFF

ON

146

OFF

ON

OFF

ON

OFF

ON

147

ON

OFF

ON

OFF

ON

148

OFF

ON

OFF

ON

OFF

ON

149

ON

OFF

ON

OFF

ON

OFF

ON

150

OFF

ON

OFF

ON

OFF

ON

151

ON

OFF

ON

OFF

ON

152

OFF

ON

OFF

ON

153

ON

OFF

ON

OFF

ON

154

OFF

ON

OFF

ON

OFF

ON

155

ON

OFF

ON

OFF

ON

156

OFF

ON

OFF

ON

157

ON

OFF

ON

OFF

ON

158

OFF

ON

OFF

ON

159

ON

OFF

ON

160

OFF

ON

OFF

ON

161

ON

OFF

ON

OFF

ON

162

OFF

ON

OFF

ON

OFF

ON

163

ON

OFF

ON

OFF

ON

164

OFF

ON

OFF

ON

OFF

ON

165

ON

OFF

ON

OFF

ON

OFF

ON

166

OFF

ON

OFF

ON

OFF

ON

167

ON

OFF

ON

OFF

ON

168

OFF

ON

OFF

ON

OFF

ON

169

ON

OFF

ON

OFF

ON

OFF

ON

170

OFF

ON

OFF

ON

OFF

ON

OFF

ON

171

ON

OFF

ON

OFF

ON

OFF

ON

172

OFF

ON

OFF

ON

OFF

ON

173

ON

OFF

ON

OFF

ON

OFF

ON

174

OFF

ON

OFF

ON

OFF

ON

175

ON

OFF

ON

OFF

ON

176

OFF

ON

OFF

ON

177

ON

OFF

ON

OFF

ON

178

OFF

ON

OFF

ON

OFF

ON

179

ON

OFF

ON

OFF

ON

180

OFF

ON

OFF

ON

OFF

ON

181

ON

OFF

ON

OFF

ON

OFF

ON

182

OFF

ON

OFF

ON

OFF

ON

183

ON

OFF

ON

OFF

ON

184

OFF

ON

OFF

ON

185

ON

OFF

ON

OFF

ON

41 / 43

186

OFF

ON

OFF

ON

OFF

ON

187

ON

OFF

ON

OFF

ON

188

OFF

ON

OFF

ON

189

ON

OFF

ON

OFF

ON

190

OFF

ON

OFF

ON

191

ON

OFF

ON

192

OFF

ON

193

ON

OFF

ON

194

OFF

ON

OFF

ON

195

ON

OFF

ON

196

OFF

ON

OFF

ON

197

ON

OFF

ON

OFF

ON

198

OFF

ON

OFF

ON

199

ON

OFF

ON

200

OFF

ON

OFF

ON

201

ON

OFF

ON

OFF

ON

202

OFF

ON

OFF

ON

OFF

ON

203

ON

OFF

ON

OFF

ON

204

OFF

ON

OFF

ON

205

ON

OFF

ON

OFF

ON

206

OFF

ON

OFF

ON

207

ON

OFF

ON

208

OFF

ON

OFF

ON

209

ON

OFF

ON

OFF

ON

210

OFF

ON

OFF

ON

OFF

ON

211

ON

OFF

ON

OFF

ON

212

OFF

ON

OFF

ON

OFF

ON

213

ON

OFF

ON

OFF

ON

OFF

ON

214

OFF

ON

OFF

ON

OFF

ON

215

ON

OFF

ON

OFF

ON

216

OFF

ON

OFF

ON

217

ON

OFF

ON

OFF

ON

218

OFF

ON

OFF

ON

OFF

ON

219

ON

OFF

ON

OFF

ON

220

OFF

ON

OFF

ON

221

ON

OFF

ON

OFF

ON

222

OFF

ON

OFF

ON

223

ON

OFF

ON

224

OFF

ON

225

ON

OFF

ON

226

OFF

ON

OFF

ON

227

ON

OFF

ON

228

OFF

ON

OFF

ON

229

ON

OFF

ON

OFF

ON

230

OFF

ON

OFF

ON

231

ON

OFF

ON

232

OFF

ON

OFF

ON

233

ON

OFF

ON

OFF

ON

234

OFF

ON

OFF

ON

OFF

ON

235

ON

OFF

ON

OFF

ON

236

OFF

ON

OFF

ON

42 / 43

237

ON

OFF

ON

OFF

ON

238

OFF

ON

OFF

ON

239

ON

OFF

ON

240

OFF

ON

241

ON

OFF

ON

242

OFF

ON

OFF

ON

243

ON

OFF

ON

244

OFF

ON

OFF

ON

245

ON

OFF

ON

OFF

ON

246

OFF

ON

OFF

ON

247

ON

OFF

ON

248

OFF

ON

249

ON

OFF

ON

250

OFF

ON

OFF

ON

251

ON

OFF

ON

252

OFF

ON

253

ON

OFF

ON

254

OFF

ON

255

ON

Table 29: SWITCH2 SETTING

6.2. OSD MENU DIAGRAM

Please see the next two pages.

43 / 43

ZONE NUMBER 1

PRESET LABEL 1 - - - - 0 1 2 3 4 5 6 7 8 9 Y Z y z A B C D E F G H I J K L M N O P Q R S T U V W X a b c d e f g h I j k l m n o p q r s t u v w x

OK CANCEL

SPACE

BACKSPACE`

ZONES

ZONE NUMBER 1 …ZONE NOT DEFINED… <EDIT ZONE LABEL> <EDIT ZONE> ENABLE ZONE ON <CLEAR CURRENT ZONE > BACK

EXIT

SYSTEM INFORMATION

MAIN

MENU

< SYSTEM INFORMATION > < DISPLAY SETUP > < DOME SETTINGS 1 > < DOME SETTINGS 2 > < DOME LABEL > RESET CAMERA REBOOT SYSTEM LANGUAGE ENGLISH EXIT

COM 2400,N,8,1 ADDRESS 1 PROTOCOL PELCO-D PRESETS 256 LANGUAGE ENGLISH TEMPERATURE 36°C SOFTWARE VERSION V4.3.3 BACK EXIT

DISPLAY SETUP

PRESET

LABEL

ON ZONE LABEL ON ZOOM ON P/T DEG ON DOME LABEL ON <LABEL POSITION> TEMPERATURE OFF BACK EXIT

DOME

SETTINGS1

<CAMERA> <MOTION> <POWER UP> <PRESETS> <PATTERNS> <ZONES> <CLEAR SET> TOTAL PRESETS NUMBER 256 BACK EXIT

ZONE DOME PRESET

SAVE

RESET

P/T DEG ZOOM

CAMERA

DIGITAL ZOOM OFF

BACKLIGHT COMP OFF <PROGRAM AE MODE> <ADDITIONAL> WIDE DYNAMIC RANGE OFF BACK EXIT

MOTION

AUTO FLIP ON PROPORTIONAL PAN ON PARK TIME

15S PARK ACTION NONE SCAN SPEED<DEG/S> 1 <SET SCAN> <MANUAL LIMIT> <SET AZIMUTH ZERO> <CLEAR AZIMUTH ZERO> BACK EXIT

POWER UP

POWER UP ACTION NONE BACK EXIT

PRESETS

PRESET NUMBER 1 …PRESET NOT DEFINED… <EDIT PRESET LABEL> <EDIT PRESET POSITION> <CLEAR CURRENT PRESET> BACK EXIT

PROGRAM AE CONTROL

AE MODE AUTO LOW LIGHT MODE AUTO LOW LIGHT LIMIT 1/50 IRIS LEVEL F2.0 AGC LEVEL 0DB BRIGHT

LEVEL 0DB/F2.0 SPOT AE OFF BACK EXIT

ADDITIONAL

IR SW MODE AUTO IR STATUS OLOR AUTO IRIS ON SHARPNESS ON SHARPNESS LEVEL 5 AUTO WHITE BALANCE AUTO R GAIN 214 B GAIN 164 BACK EXIT

PRESET NUMBER 1

PRESET LABEL 1 - - - - 0 1 2 3 4 5 6 7 8 9 Y Z y z A B C D E F G H I J K L M N O P Q R S T U V W X a b c d e f g h I j k l m n o p q r s t u v w x

OK CANCEL

SPACE

BACKSPACE`

PATTERNS

PATTERN NUMBER

1

<CLEAR CURRENT

PATTERN> BACK EXIT

DOME SETTINGS 2

<ALARMS> <ADDR SETTING> <PASSWORD> <WINDOWS BLANKING> <HEATER SETTING> <CRUISE SETTING> <TRACKING SETTING> BACK EXIT

(To be continued)

CLEAR SET

CLEAR ZONES CLEAR PRESETS CLEAR PATTERNS RESTORE FACTORY DEFAULT BACK EXIT

44 / 43

DOME SETTINGS 2

<ALARMS> <ADDR SETTING> <PASSWORD> <WINDOWS BLANKING> <HEATER SETTING> <CRUISE SETTING> <TRACKING SETTING> BACK

EXIT

ALARMS

ALARM NUMBER 1 SEQUENCE(SECS) 1 ALARM ACT CRUISE ACTIVATE AUX OFF <CLEAR SET> DWELL TIME<SECS>1 0 DWELL TIME<SECS>2 0 BACK EXIT

ADDR

SETTING

ADDR TYPE

HARD

ADDR SOFT

255

ADDR HARD

0

BACK

EXIT

PASSWORD

ENABLE PASSWORD

OFF <EDIT PASSWORD> BACK EXIT

WINDOWS

BLANKING

STYLE

GRAY BLANK ALL ABOVE OFF BALANK ALL BELOW OFF <SET

WINDOWS>

SET MASK

COLOR

4 BACK EXIT

SET

WINDOWS

WINDOWS NUMBER 1 <EDIT WINDOW LOCATION> <EDIT WINDOW ZOOM > ENABLE WINDOW OFF CLEAR CURRENT WINDOW BACK EXIT

HEATER

SETTING

HEATER DISPLAY ON

HEATER MODE AUTO

TEMPERATURE SET 33℃ BACK

EXIT

EDIT WINDOW ZOOM

IRIS OPEN TO CONTINUE IRIS CLOSE TO CANCEL

EDIT WINDOW

LOCATION

CRUISE

DWELL

TIME<SECS>

7 PRESET

LIST

1

1 ON

0

IRIS OPEN TO CONTINUE IRIS CLOSE TO CANCEL

OFF 1234567890 < PRESET 1-10> 0110010111 BACK EXIT

TRACKING

SETTING

DEFAULT

SETTING SIZE SENS MEDIUM GRAY SENS MEDIUM LOST ACT STOP TRACK ZOOM

SETTING

ON

WAIT

TIME<S>

40

<TRACKING

BOUNDARY>

AUX

OFF TRACKING SPEED AUTO TRACKING TIME<M> AUTO BACK EXIT

TRACKING BOUNDARY

BOUNDARY LIMIT OFF CLEAR BOUNDARY LEFT LIMIT OFF RIGHT LIMIT OFF UP LIMIT OFF DOWN LIMIT OFF BACK EXIT

DOME

LABEL

<EDIT DOME LABEL> <CLEAR DOME LABEL> BACK

EXIT

EDIT DOME LABEL DOME LABEL 0 1 2 3 4 5 6 7 8 9 Y Z y z A B C D E F G H I J K L M N O P Q R S T U V W X a b c d e f g h I j k l m n o p q r s t u v w x

OK CANCEL

SPACE BACKSPACE