VLPR-54L922D
Professional Car License Plate Camera
User Manual
Veilux Inc.
safety information
CAUTION
Never point the camera toward the sun
1.
Do not expose the lens directly to the sun or to strong light as this may damage the
pick-up device.
2.
Handle this camera with care
Avoid any shock of the camera. Improper handing could damage the camera.
3. Requires a proper operating environment
This camera is designed for both indoor and outdoor use. The allowable temperature
range of operation of this camera is between -10°C~50°C and the allowable humidity
is 80% maximum.
4.
Clean the lens regularly
It is recommended that the lens surface be cleaned regularly or when the lens is dusty
to prevent obstruction of IR light. Cleaning should be done by using a chamois, a very
fine soft cloth, lens tissue or cotton tipped applicator and ethanol to carefully remove
any fingerprint of dust.
Check the power source voltage
5.
The power source voltage should be within the specified range.
(Camera must meet the specification)
2 safety information
content
CONTENT
INTRODUCTION
Features
Dimension
INSTALLATION
Nomenclature and Function
Installation
Important Notes
TECHNICAL INFORMATION
Specification
4
4
5
6
8
9
3 content
introduction
FEATURES
DIMENSION
Lead (Pb) Free RoHS Compliance1.
2.
Digital Signal Processor. Sony HQ1
3.
Long life and high reliability are achieved by the use of a CCD image device. This
makes the camera 100% solid state.
4.
Lower power consumption
The FL-ON Shutter is fixed at 1/230 second.
From Night to Day, the delay time is 5~6 minutes.
Relatively no interference from magnetic or electrostatic field.
Patent designed external varifocal lens adjustment for users to adjust the focus
conventiently without removing the cover.
The cable management bracket protects the camera cables inside the bracket to keep
it away from humidity in outdoor environment.
Mechanical Visible Light Filter
This Mechanical Visible Light Filter will be triggered by strong focused illumination.
Whenver strong light appears, it will filter out the strong light automatically so that
clear and readable quaility images can be ensured.
5.
6.
7.
8.
9.
10.
11.
Easy of use in any application is achieved through the small size.
4 introduction
installation
NOMENCLATURE AND FUNCTION
External Varifocal Lens Adjustment (Wide/Tele)
1.
Please use a “flat-head” screw driver to adjust the lens angle for wide and telephoto
2. External Varifocal Lens Adjustment (Near/Far)
Please use a “flat-head” screw driver to adjust the lens focus for near and far.
External Varifocal Lens Adjustment
DC Level and HIR LEDs Adjustment
3. DC Level
The VR for adjusting the IRIS level of DC Auto Iris Lens.
Please lift the waterproof lid and use a small screw driver to adjust the DC leve. After
the setting is done, please cover back the waterproof lid.
4. HIR LEDs Adjustment
Ther external IR LEDs adjustment is used to adjust the brightness of the 6 pieces high
power reflection IR light. As the installation environment changes or according to
different illumination conditions, users can adjust a proper IR brightness.
5 installation
installation
INSTALLATION
Please adhere the paster provided to the surface where you like to install the bracket
on the wall as Fig1. In accordance with the position of 4 holes shows on the paster to
dig 4 holes, and then insert 4 anchors provided into the holes as shown in Fig2.
1.
Mounting the camera to the wall by 4 screws. You can let the camera cables go along
the sides (as Fig3) or go downward (as Fig4). If the cable goes downward, a plastic
cable protector provided is needed (shown in Fig4).
2.
In accordance with the direction shown in Fig5 to adjust the direction of the camera
bracket as you like.
3.
6 installation
installation
INSTALLATION
Please note: During camera adjustment, there are 2 screws as shown in Fig6 which
4.
you don’t need to unfasten them.
Use an “L” type wrench provided to fasten the screw to the buttom of the camera as
5.
Fig7. (Please hold the camera until the installation is finished.)
Then, use the wrench to fasten the screw to the connector of the camera and bracket
6.
as shown in Fig8. (Please hold the camera until the installation is finished.)
7 installation
installation
INSTALLATION
IMPORTANT NOTES
Use the wrench to fasten the screw to the bracket as shown in Fig9. (Please hold
the camera until the installation is finished.)
7.
Then the camera installation is finished as Fig10 shows.8.
To simulate the motion of cars in the parking lot, it takes 3-5 minutes to switch from
B/W mode to Color mode.
1.
The maximum elevation angle of LPR function is 20° degrees. (Refer to Fig11.)2.
8 installation
technical information
SPECIFICATION
9 technical informataion
ITEM VLPR-54L922D
TV System
NTSC
811(H) x 508(V) 795(H) x 596(V)
1/3” Sony Super HAD CCD II
540 TV Lines, Sony HQ1
9SS&RPSRVLWH
More than 50dB
30 Units (IR LEDs ON<2 Lux, IR LEDs OFF>5 Lux)
0.45
DC
IP66
12V DC / 24V AC
-10°C ~ 50°C / -20°C ~ 60°C
Maximum: RH80% / RH90%
93(Ø) x 163(L)mm
1,000g (2.2lbs.)
DC Level
Built-in DC Auto IRIS Lens
29.2° ~ 13.0°
6 ~ 13m (19.7 ~ 42.7ft)
f9mm~22mm/F1.4 Aspherical D/N Lens
Internal
Automatic
Automatic
Automatic
Automatic Dynamic Digital Noise Reduction (DNR)
Automatic, 1/50 (60) ~ 1/100,000 sec
Automatically Switches from B/W to
Color mode, Switching Time: 3~5min
0 Lux
PAL
Image Sensor
Number of Pixel
Resolution, DSP
Minimum Illumination
Video Output
Signal to Noise Ratio
Gamma Correction
Mechanical Visible
Light Filter
IR LED
Synchronizing System
Auto Electronic Shutter
Auto Gain Control
Auto White Balance
Digital Noise Reduction
Sense Up
Automatic IRIS
Adjustment VR
Lens Mount
Lens
Angle of View (H)
License Plate Distance
Water Resistance
Power Supply
Operation/Storage Temp
Operat/Stor Humidity
Dimension
Net Weight
3015 Eagle Drive, Suite 100
Grand Prairie, Texas 75052
Toll Free: (800) 510-6528
Local: (214) 635-4855
Fax: (214) 988-2858
www.veilux.net
Loading...