Veeder-Root TLS-4 Series, TLS-450 Console Hardware Replacement
TLS-4xx Series Consoles
Console Hardware Replacement
Manual No: 577013-956 ● Revision: B
Notice
Veeder-Root makes no warranty of any kind with regard to this publication, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose.
Veeder-Root shall not be liable for errors contained herein or for incidental or consequential damages in connection with the
furnishing, performance, or use of this publication.
Veeder-Root reserves the right to change system options or features, or the information contained in this publication.
This publication contains proprietary information which is protected by copyright. All rights reserved. No part of this publication
may be photocopied, reproduced, or translated to another language without the prior written consent of Veeder-Root.
Contact TLS Systems Technical Support for additional troubleshooting information at 800-323-1799.
DAMAGE CLAIMS / LOST EQUIPMENT
Thoroughly examine all components and units as soon as they are received. If any cartons are damaged or missing, write a
complete and detailed description of the damage or shortage on the face of the freight bill. The carrier's agent must verify the
inspection and sign the description. Refuse only the damaged product, not the entire shipment.
Veeder-Root must be notified of any damages and/or shortages within 30 days of receipt of the shipment, as stated in our Terms
and Conditions.
VEEDER-ROOT’S PREFERRED CARRIER
1. Contact Veeder-Root Customer Service at 800-873-3313 with the specific part numbers and quantities that were missing
or received damaged.
2. Fax signed Bill of Lading (BOL) to Veeder-Root Customer Service at 800-234-5350.
3. Veeder-Root will file the claim with the carrier and replace the damaged/missing product at no charge to the customer.
Customer Service will work with production facility to have the replacement product shipped as soon as possible.
CUSTOMER’S PREFERRED CARRIER
1. It is the customer’s responsibility to file a claim with their carrier.
2. Customer may submit a replacement purchase order. Customer is responsible for all charges and freight associated with
replacement order. Customer Service will work with production facility to have the replacement product shipped as soon as
possible.
3. If “lost” equipment is delivered at a later date and is not needed, Veeder-Root will allow a Return to Stock without a restocking
fee.
4. Veeder-Root will NOT be responsible for any compensation when a customer chooses their own carrier.
RETURN SHIPPING
For the parts return procedure, please follow the appropriate instructions in the "General Returned Goods Policy” pages in the
"Policies and Literature" section of the Veeder-Root North American Environmental Products price list. Veeder-Root will not
accept any return product without a Return Goods Authorization (RGA) number clearly printed on the outside of the package.
©Veeder-Root 2008. All rights reserved
.
Figures
Table of Contents
Introduction
Contractor Certification Requirements ..............................................................................1
Before You Begin ..............................................................................................................2
Safety Precautions ............................................................................................................2
Precautions Against Static Electricity ................................................................................3
Before Turning Off Power .................................................................................................3
Replacing the Display Door Assembly (P/N 330020-625)......................4
Replacing the Printer Door Assembly (P/N 330020-626)........................6
Replacing the Power Supply (P/N 330020-623)............................................8
Figure 1. USB/Ethernet board - V-R thumb drive port...............................................3
Figure 2. Front doors.................................................................................................4
Figure 3. Display door cables....................................................................................5
Figure 4. Printer door cables .....................................................................................6
Figure 5. Remove USB cable and CF card...............................................................8
Figure 6. Remove AC Channel cover........................................................................9
Figure 7. Removing AC Input module .....................................................................10
Figure 8. Removing Power Supply..........................................................................11
Figure 9. Replacing Power Supply shield over Power Supply board ......................12
iii
Introduction
This manual contains instructions for replacing the following TLS-4XX console components:
• Display Door Assembly (P/N 330020-625)
• Printer Door Assembly (P/N 330020-626)
• Power Supply (P/N 330020-623)
This manual does not provide troubleshooting information.
Contractor Certification Requirements
Veeder-Root requires the following minimum training certifications for contractors who will install and setup the
equipment discussed in this manual:
Installer Certification: Contractors holding valid Installer Certification are approved to perform wiring and
conduit routing, equipment mounting, probe and sensor installation, tank and line preparation, and line leak
detector installation.
TLS-350 Technician Certification: Contractors holding valid TLS-350 Technician Certifications are approved to
perform installation checkout, startup, programming and operations training, troubleshooting and servicing for all
Veeder-Root TLS-300 or TLS-350 Series Tank Monitoring Systems, including Line Leak Detection and associated
accessories.
TLS-450 Technician Certification: Contractors holding valid TLS-450 Technician Certifications are approved to
perform installation checkout, startup, programming and operations training, troubleshooting and servicing for all
Veeder-Root TLS-450 Series Tank Monitoring Systems, including Line Leak Detection and associated accessories.
In-Station Diagnostics (ISD) Technician Certification: Contractors holding valid ISD Technician
Certifications are approved to perform installation checkout, startup, programming and operations training,
troubleshooting and servicing for all Veeder-Root In-Station Diagnostics hardware, including ISD-PMC and
Carbon Canister Vapor Polisher.
Warranty Registrations may only be submitted by selected Distributors.
1
Introduction Before You Begin
OFF
OFF
Before You Begin
Before you begin component replacement, read the following guidelines:
• To avoid electrical shock, be sure AC power to the console is Off when performing the procedures in this
manual.
• Failure to comply with these requirements could result in death, serious personal injury, property loss, or
equipment damage.
Safety Precautions
The following safety symbols may be used throughout this manual to alert you to important safety hazards and
precautions.
ELECTRICITY
High voltage exists in, and is supplied
to, the device. A potential shock hazard
exists.
INJURY
Careless or improper handling of tools
can cause bodily injury.
READ ALL RELATED MANUALS
Knowledge of all related procedures
before you begin work is important.
Read and understand all manuals thoroughly. If you do not understand a procedure, ask someone who does.
WARNING
This system operates on 115 Vac power. Serious injury or death from electrical
shock could occur if the power ON/OFF warnings in this manual are not
heeded.
1. Read and follow all instructions in this manual, including all safety
warnings.
2. Remove rings from hands, metal watch bands and bracelets, and loose
hanging neck jewelry before performing these procedures.
3. Do not modify or use service parts other than those provided by VeederRoot.
TURN POWER OFF
Live power to a device creates a
potential shock hazard. Turn Off power
to the device and associated accessories when servicing the unit.
STATIC SENSITIVE COMPON ENTS
Wear grounded anti-static wrist strap
before handling the printed circuit
board.
2
Loading...