Veeder Root Series C628 Single Preset Counter Technical Manual

Introduction

Your V eeder-Root brand C628 Single Preset Counter is one model in a family of 1/8 DIN units which offers breakthrough display technology as well as easy-to-program single-line parameters. Designed to provide instant visual feedback regarding an application’s key input value, the C628 not only has a 0.71” high LED display (27% larger than other 1/8 DIN units), but also the ability to change display color based on process status (programmable parameter in Operation Mode). Easy programming is made possible via a help function and a secondary legend display.

This manual will guide you through the installation and wiring of your C628 unit with information on proper panel mounting and rear terminal layout and wiring instructions. In addition, the instrument’s operation and programming modes are thoroughly explained. The Operation Mode provides day to day operation and allows editing of preset values. The Program Mode enables the configuration of various parameters prior to initial operation. These parameters include those for basic configuration as well as other settable features which will enhance the functionality and usability of the device.

This manual also provides information on the C628 Single Preset Counter’s transistor and relay outputs, product specifications, and ordering and warranty procedures.

Technical Manual 702138-0006

Features

• AWESOME 0.71” high digit LED display

• Programmable color change display based on an event

• Programmable help function and secondary legend display

• Choice of NPN or PNP primary input

• Filter speed settable for 20, 200, or 10,000 Hz

• Standard outputs: one NPN transistor & one relay

• Front panel reset enable and preset lockout

• Optional RS-485 plug in card

• CE approved

Index

Installation

Panel Mounting page 2 Wiring page 3

Operation

Front Panel page 4 Operation Mode page 5

Programming

Program Mode page 6-10

Appendix A

Specifications page 11

General

Ordering Information page 12 Warranty page 12

Veeder-Root

brand

Series C628 Single Preset Counter

(C628-7XXX)

INSTALLATION

PANEL MOUNTING

100mm

82344

Mounting Grooves

VEEDER-ROOT

PGM

96mm

OP1 OP2

48mm

RST

92mm +0.5 -0.0

CUTOUT

14 15 16 17 18 19 20

10 11 12

10mm

PANEL

45mm

+0.5 -0.0

SIZE

The instrument can be mounted in a panel with a thickness of up to 6mm. The cutout(s) should be made based on the recommended panel opening illustrated in the drawing above.

Insert the unit in the panel through the cutout. Ensure that the panel gasket is not distorted and the instrument is positioned squarely against the panel. Slide the mounting clamp into place on the instrument, as shown to the left, and push it forward until it is firmly in contact with the rear face of the mounting panel and the tabs on the bracket arm are seated in the mounting grooves on the side of the unit.

345 678

The electronic components of the instrument can be removed from the housing after installation without disconnecting the wiring. To remove the components, grip the side edges of the panel and pull the instrument forward. Take note of orientation of the unit for subsequent replacement in the housing.

Bracket Arm

INSTALLATION

WIRING

REAR TERMINAL CONNECTIONS

Power Supply + VDC -

RS-485 Comm. (opt.)

B A

COM

Relay 1

14 15 16 17 18 19 20

22 23

10 11 12

Common

NPN Out 1

Digital In 2

(sec. lockout)

Count Inputs

Terminal #2 is the connection for Input A, which is programmable to be

Digital In 1

(rem. reset)

Aux. Power

(opt.)

units. The neutral side for AC powered units and the negative side for DC powered units are connected to Terminal #14.

23 4 5 6 78

Input A

Input Common

the primary input or channel A of an encoder input. Terminal #1 is the connection for Input B, which is programmable to be an incrementing input, a decrementing input, or channel B of an encoder input. The common connection for both Input A and Input B is Terminal #3.

Transistor Outputs

Your unit comes standard with an NPN output which is activated by the preset. Transistor Output 1, which is tied to Preset 1 operation, is on Terminal #7. Terminal #8 serves as the common connection for the

Control/Digital Inputs

transistor output.

A contact closure or NPN signal can be used to activate preconfigured functionality. Terminal # 5 is used for a remote reset function, while Terminal #6 is a security function, that when active, will prohibit entry into Program Mode. Terminal #8 serves as the common for both of these inputs.

Relay Outputs

Your unit comes standard with a relay output which is tied to Preset 1 operation. Terminal #19 is NC, Terminal #20 is common, and Terminal #21 is NO.

Input B

Auxiliary Power Output

A 9 - 15 VDC for powering external sensors and encoders up to 125 mA can be accessed by connecting the positive supply side of the sensor to Terminal #4 and the negative side to Terminal #8.

Serial Communication

An RS-485 communication board, utilizing ASCII protocol, can be installed as an option. Terminals #16 & #17 serve as the B and A connections respectively, while Terminal #18 is connected as the common.

Input Power

For an AC powered unit, Terminal #13 serves as the line or Hot side connection for AC powered units and as the positive side for DC powered

Terminals 9, 10, 11, 12, 15, 22, 23, & 24 are not used.

OPERATION

FRONT PANEL

VEEDER-ROOT

Primary Display

OP1 OP2

Output Indicator

82345

PGM

RST

Down Key Scroll Key Program Key Reset Key

Key Functions

Key

Down In Operation Mode: Used in edit operation to decrement

the digit highlighted by the Scroll key. In Program Mode: Used in Edit Operation to decrement

the digit highlighted by the Scroll key, if the setting is a numerical value, or present the next in the series of choices for that parameter.

Scroll

Program In Operation Mode: Used to move between the count

In All modes: Moves the unit into Edit Operation, which is indicated by the left most digit flashing. Successive presses of the key are used to move to the digit to be edited. Wrap around will occur from least significant digit to most significant digit.

value display & the preset and to enter an edited preset value. Holding the key down for 3 seconds will cause the unit to enter Program Mode.

In Program Mode: Used to move from one parameter to the next and enter the edited parameter values. Holding the key down for 3 seconds will cause the unit to return to Operation Mode.

Function

Display

Primary In Operation Mode: Default display is the count value.

Secondary In Operation Mode: Indicates numerically if Preset 1 is

Output Indicators

Secondary Display

Display Functions

Function

Can be scrolled using the program key to display the Preset 1 value. If the "Help" function is enabled, this display will first show the parameter description for 3 seconds (see page 5 for example).

In Program Mode: Displays the value or selection for the current parameter. If the "Help" function is enabled, this display will first show the parameter description for 3 seconds (see page 6 for example).

being viewed on the primary display. This display is blank when the Count Value is being shown.

In Program Mode: Provides a 1 digit alpha or numeric character to indicate which parameter value is being shown on the primary display.

In Operation Mode: OP1 illuminates when Output 1 is active.

In Program Mode: No function.

Reset In Operation Mode: Resets the count value to zero (or

to the preset in count down operation). This button can be disabled via the "Front Panel Reset Enable" parameter in Program Mode.

In Program Mode: No function.

Down & Scroll together

In All modes: Will abort an Edit Operation and return the preset/parameter to its previous value.

+ 8 hidden pages