Vector Start-IT VECO21 ST Owner's Manual

Page 1
Page 2
TABLE OF CONTENTS
WARNINGS 1 CAUTIONS 2 FEATURES 3 IMPORTANT SAFETY INFORMATION 4
1. INTRODUCTION 5
2. USING START-IT TM AS A JUMPSTART SYSTEM
2.1 Easy, Step-by-Step Jumpstarting Instructions 6
3. CHARGING/RECHARGING
3.1 110/1 20-Volt AC Charging 8
3.2 12-Volt DC Charging 8
9
3.4 Estimated Battery Life 9
4. OPERATING AS A PORTABLE POWER SUPPLY
4.1 Operating as a 12-Vail DC Power Supply 9
4.2 Estimated 12-Volt DC Usage Times 10
4.3 Operation as a 110/120-Volt AC Power Supply 10
5. EMERGENCY/WORK LIGHT 10
6. BATTERY REPLACEMENT
6.1 Battery Disposal 11
7. SPECIFICATIONS 11
WARRANTY
120 Day Limited Warranty 12 3 Year Extended Warranty 13
Page 3
WARNINGS
WARNING STATEMENTS IDENTIFY CONDITIONS OR PRACTICES
THAT MAY RESULT IN PERSONAL INJURY OR LOSS OF LIFE
1. WHEN WORKING WITH LEAD ACID BATTERIES, ALWAYS MAKE SURE IMMEDIATE ASSISTANCE IS AVAILABLE IN CASE OF ACCIDENT OR EMERGENCY.
2. ALWAYS USE PROTECTIVE EYEWEAR WHEN USING THIS PRODUCT: CONTACT WITH BATTERY ACID MAY CAUSE BLINDNESS AND/OR SEVERE BURNS. BE AWARE OF FIRST AID PROCEDURES IN CASE OF ACCIDENTAL CONTACT WITH BATTERY ACID.
3. THERE IS A RISK OF EXPLOSIVE GASES BEING RELEASED WHEN LEAD ACID BATTERIES ARE BEING CHARGED OR DISCHARGED. FAILURE TO FOLLOW INSTRUCTIONS MAY CAUSE PROPERTY DAMAGE, EXPLOSIVE HAZARD AND/OR PERSONAL INJURY.
4. WHEN CHARGING UNIT FROM A 110/120-VOLT AC ELECTRICAL OUTLET IN ANY WET OR DAMP AREA, MAKE SURE THAT THE OUTLET USED IS PROTECTED BY A GROUND FAULT INTERRUPT (GFI) SWITCH.
5. WHEN CHARGING THE UNIT NEAR WATER, DO NOT ALLOW THE ELECTRICAL CORDS AND OUTLETS TO GET WET OR COME NEAR WATER—ELECTRICAL SHOCK COULD RESULT!
6. JUMPSTART PROCEDURES SHOULD ONLY BE PERFORMED IN A SAFE, DRY, WELL VENTILATED AREA.
7. ALWAYS STORE BATTERY CLAMPS IN BUILT-IN HOLSTERS WHEN NOT IN USE. NEVER TOUCH BATTERY CLAMPS TOGETHER—THIS CAN CAUSE DANGEROUS SPARKS, POWER ARCING, AND/OR EXPLOSION.
8. WHEN USING THIS UNIT IN PROXIMITY TO THE VEHICLE*S BATTERY AND ENGINE, STAND THE UNIT ON A FLAT, STABLE SURFACE, BE SURE TO KEEP ALL CLAMPS, CORDS, CLOTHING AND BODY PARTS AWAY FROM MOVING VEHICLE COMPONENTS.
9. DO NOT WEAR VINYL CLOTHING WHEN JUMPSTARTING A VEHICLE—FRICTION CAN CAUSE DANGEROUS STATIC ELECTRICITY SPARKS. REMOVE ALL JEWELRY OR METAL OBJECTS THAT COULD CAUSE SHORT CIRCUITS OR REACT WITH BATTERY ACID.
10. ALWAYS DISCONNECT THE NEGATIVE (BLACK) JUMPER CABLE FIRST: FOLLOWED BY THE POSITIVE (RED) JUMPER CABLE.
11. NEVER ALLOW RED AND BLACK CLAMPS TO TOUCH EACH OTHER OR ANOTHER COMMON METAL CONDUCTOR—THIS COULD CAUSE DAMAGE TO THE UNIT AND/OR CREATE SPARKING/EXPLOSION HAZARD. ALWAYS STORE BATTERY CLAMPS IN BUILT-IN HOLSTERS WHEN NOT IN USE.
12. DO NOT EXPOSE BATTERY TO FIRE OR INTENSE HEAT AS IT MAY EXPLODE. BEFORE DISPOSING OF THE BATTERY, PROTECT EXPOSED TERMINALS WITH HEAVY-DUTY ELECTRICAL TAPE TO PREVENT SHORTING (SHORTING CAN RESULT IN INJURY OR FIRE).
13. DO NOT SMOKE OR USE INFLAMMABLE ITEMS (MATCHES, CIGARETTE LIGHTERS, ETC.) WHILE WORKING ON A VEHICLE*S BATTERY SYSTEM.
14. KEEP UNIT OUT OF REACH OF CHILDREN (WHETHER STORED, OR IN USE).
15. IF AUDIBLE ALARM SOUNDS - DO NOT TURN ON SAFETY SWITCH. REVERSE CLAMP CONNECTIONS
POLARITY.
FIRST AID:
1. SKIN: IF BATTERY ACID COMES IN CONTACT WITH SKIN, RINSE IMMEDIATELY WITH WATER, THEN WASH
2. EYES: IF BATTERY ACID COMES IN CONTACT WITH EYES, FLUSH EYES IMMEDIATELY—FOR MINIMUM OF 15
THOROUGHLY WITH SOAP AND WATER. IF REDNESS, PAIN, OR IRRITATION OCCURS, SEEK IMMEDIATE MEDICAL ATTENTION.
MINUTES—SEEK IMMEDIATE MEDICAL ATTENTION.
Page 4
CAUTIONS
CAUTION STATEMENTS ADVISE AGAINST CERTAIN CONDITIONS AND PRACTICES THAT MAY RESULT IN DAMAGE TO VEHICLES, APPLIANCES, AND/OR THE START-IT JUMPSTART SYSTEM.
1. IMPORTANT: ALTHOUGH THIS UNIT IS DELIVERED IN A PARTIALLY-CHARGED STATE - YOU MUST FULLY CHARGE IT WITH THE SUPPLIED 110/120-VOLT AC CHARGER FOR A FULL 24 HOURS, BEFORE USING IT FOR THE FIRST TIME.
2. IMPORTANT: DO NOT OVERCHARGE UNIT, THIS WILL REDUCE BATTERY LIFE.
3. USE ONLY THE SUPPLIED CORDS FOR RECHARGING/OPERATING THIS UNIT. DO NOT RECHARGE FOR MORE THAN 3-4 HOURS MAXIMUM USING 12-VOLT DC METHOD. RECHARGE UNIT AFTER EACH USE.
4. ALL ON/OFF SWITCHES SHOULD BE IN THE OFF POSITION WHEN THE UNIT IS CHARGING OR NOT IN USE. MAKE SURE ALL SWITCHES ARE IN THE OFF POSITION BEFORE CONNECTION TO A POWER SOURCE OR LOAD.
5. NEVER INSERT ANYTHING OTHER THAN THE SUPPLIED POWER/RECHARGING CORDS OR RECOMMENDED APPLIANCE POWER/RECHARGING CORDS INTO THE 12-VOLT DC CHARGING/POWER SOCKET ON THIS UNIT. DO NOT USE ANY ACCESSORY THAT IS NOT RECOMMENDED OR PROVIDED BY THE MANUFACTURER.
6. DO NOT USE THIS UNIT TO OPERATE DC APPLIANCES THAT DRAW MORE THAN 20 AMPS.
7. THIS SYSTEM IS DESIGNED TO BE USED ONLY ON VEHICLES WITH 12-VOLT DC BATTERY SYSTEMS. DO NOT CONNECT TO A 6-VOLT OR 24-VOLT BATTERY SYSTEM.
8. THIS SYSTEM IS NOT DESIGNED TO BE USED AS A REPLACEMENT FOR A VEHICULAR BATTERY. DO NOT ATTEMPT TO JUMPSTART A VEHICLE THAT DOES NOT HAVE A BATTERY INSTALLED.
9. VEHICLES THAT HAVE ON-BOARD COMPUTERIZED SYSTEMS MAY BE DAMAGED IF VEHICLE BATTERY IS JUMPSTARTED. BEFORE JUMPSTARTING, READ THE VEHICLE’S OWNER’S MANUAL TO CONFIRM THAT EXTERNAL—STARTING ASSISTANCE IS ADVISED.
10. EXCESSIVE ENGINE CRANKING CAN DAMAGE A VEHICLE’S STARTER MOTOR. IF THE ENGINE FAILS TO START AFTER THE RECOMMENDED NUMBER OF ATTEMPTS, DISCONTINUE JUMPSTART PROCEDURE AND LOOK FOR OTHER PROBLEMS THAT MAY NEED TO BE CORRECTED.
11. ALTHOUGH THIS UNIT CONTAINS A NON-SPILLABLE BATTERY, IT IS RECOMMENDED THAT UNIT BE KEPT UPRIGHT DURING STORAGE, USE AND RECHARGING. TO AVOID POSSIBLE DAMAGE THAT MAY SHORTEN THE UNIT’S WORKING LIFE, PROTECT IT FROM DIRECT SUNLIGHT, DIRECT HEAT, AND/OR MOISTURE.
12. CHECK UNIT PERIODICALLY FOR WEAR AND TEAR. REPLACE WORN OR DEFECTIVE PARTS IMMEDIATELY CONTACT VECTOR® CUSTOMER SERVICE DEPARTMENT AT: (954) 584-4446 OR TOLL FREE NUMBER: (866) 584-5504 XT. 19.
13. DO NOT ATTEMPT TO JUMPSTART A FROZEN BATTERY.
14. NEVER SUBMERGE THIS UNIT IN WATER.
15. THIS UNIT WILL NOT OPERATE APPLIANCES AND EQUIPMENT THAT PRODUCE HEAT, SUCH AS DRYERS, MICROWAVE OVENS, AND TOASTERS.
TM
BATTERY REPLACEMENT:
IT IS RECOMMENDED TO RETURN UNIT TO VECTOR® CUSTOMER SERVICE FOR BATTERY REPLACEMENT: CONTACT (954) 584-4446 EXT. 19, OR TOLL-FREE (866) 584-5504
BATTERY DISPOSAL:
THIS UNIT CONTAINS A MAINTENANCE-FREE, SEALED, NON-SPILLABLE, LEAD ACID BATTERY
WHICH MUST BE DISPOSED OF PROPERLY. SOME STATES REQUIRE RECYCLING.
DISPOSAL QUESTIONS? IN USA, CALL 1 -877-288-7722.
Page 5
FEATURES
!! Heavy duty, professional quality
! Easy-to-use: emergency jumpstarter for cars, light trucks, let skis, snowmobiles, farm equipment, airplanes, boats, small SUVs and RVs (almost any 12-volt battery system)
! Provides INSTANT 12-VOLT DC POWER whenever, and wherever it*s needed
! Ideal for farm/ranch, home, tailgate parties, beach, picnic, campsite, wilderness, utility power outages, emergency repair, etc
! Sturdy and compact unit provides up to 50 hours of completely portable 12-volt DC power
! Built-in cigarette lighter-type socket for use with 12-volt DC accessories or DC/AC Inverter for use with 110/120-volt AC
accessories
!! Portable, safe & convenient — goes where extension cords can*t reach and utility power is not available
! ON/OFF safety power switch (no key required, no key to get lost)
!! Built in audible reverse polarity alarm
!! Cordless/rechargeable includes charging cords for standard 110/120-volt AC wall socket, and vehicle*s 12-volt DC accessory
outlet
!! Powerful 400 instantaneous cranking amps; 1 200 peak amps
! Solid-state, automatic operation and built-in circuit protection
!! Safe to use, transport, and store
! Includes non-spillable, maintenance-free, heavy-duty, 19 amp hour sealed battery
! Requires no maintenance (other than recharging) for optimum operation
! Molded high-impact case is tough and durable
!! Built-in, Heavy-duty, industrial grade copper clamps and jumper cables - with exclusive spring-loaded, quick-release storage holsters
! 110/120-volt AC charger is Underwriter Laboratories safety tested and listed
! Easy-to-read LED, battery charging/status indicators
! Built-in halogen work/emergency light with ultra-bright krypton bulb for roadside repairs and use in remote location without utility
power
Page 6
NOTE: The Start-It Jumpstart System is equipped with an audible Reverse Polarity Alarm. This
feature is only active when the Safety Switch is turned OFF. After both battery clamp connections are made during jump-start procedures, if you hear a buzzing sound, DO NOT TURN ON THE SAFETY SWITCH. You must swap the clamp connections before continuing. If the buzzer does not sound, it is safe to turn on the Safety Switch Jumpstart procedure.
NOTE: The alarm requires at least two volts to operate, so in the rare instance of a totally dead
battery, the alarm may not sound if the polarity connection is reversed. This is very unlikely because almost all dead batteries rarely go below four or five volts. Always double-check your connections before turning on the Safety Switch.
IMPORTANT INFORMATION:
CAUTION: READ INSTRUCTION MANUAL AND PRODUCT LABELING CAREFULLY, FOR COMPLETE
INSTRUCTIONS, BEFORE USING THIS PRODUCT. FOLLOW RECOMMENDED WARNINGS, CAUTIONS, SAFETY PROCEDURES, AND MANUFACTURER GUIDELINES FOR YOUR VEHICLE*S BATTERY.
1. IMPORTANT: ALTHOUGH THIS UNIT IS DELIVERED IN A PARTIALLY-CHARGED STATE—YOU MUST
FULLY CHARGE IT WITH THE SUPPLIED 110/120-VOLT AC CHARGER FOR A FULL 24 HOURS, BEFORE USING IT FOR THE FIRST TIME.
2. IMPORTANT: DO NOT OVERCHARGE UNIT, THIS WILL REDUCE BATTERY LIFE. CHARGE UNTIL GREEN “CHARGED” INDICATOR IS LIT WHEN CHARGE STATUS BUTTON IS PRESSED. AFTER GREEN “CHARGED” INDICATOR LIGHT COMES ON WHEN CHARGE STATUS BUTTON IS PRESSED, UNIT CAN BE TOP-OFF CHARGED FOR AN ADDITIONAL HOUR USING THE DC METHOD OR 2-4 HOURS USING THE AC METHOD.
3. FULLY RECHARGE UNIT AFTER EACH USE, OR WHEN CHARGE STATUS INDICATOR SHOWS LOWER THAN 4 RED LED, AND EVERY 2 MONTHS WHEN NOT IN USE.
4. ALWAYS RECHARGE IN A DRY, WELL-VENTILATED AREA, AWAY FROM WATER.
5. WHEN CHARGING IN ANY WET OR DAMP AREA FROM A 110/120-VOLT ELECTRICAL OUTLET, MAKE
SURE THAT THE OUTLET USED IS PROTECTED BY A GROUND FAULT CIRCUIT INTERRUPT (GFCI) CIRCUIT
6. WHEN CHARGING THE UNIT NEAR WATER (POOL, DOCKSIDE, BEACH, ETC.) DO NOT ALLOW THE ELECTRICAL CORDS AND OUTLETS TO GET WET OR COME NEAR WATER ELECTRICAL SHOCK COULD RESULT!
7. USE ONLY THE SUPPLIED CORDS FOR RECHARGING/OPERATING THIS UNIT.
8. IT IS RECOMMENDED THAT UNIT BE KEPT UPRIGHT DURING USE AND WHEN RECHARGING.
9. WHEN NOT IN USE, STORE UNIT WITH ON/OFF SWITCH TURNED OFF.
SAFETY WARNINGS:
1. THERE IS A RISK OF EXPLOSIVE GASES BEING RELEASED WHEN BATTERIES ARE IMPROPERLY CHARGED OR DISCHARGED. FAILURE TO FOLLOW INSTRUCTIONS MAY CAUSE PROPERTY DAMAGE, EXPLOSIVE HAZARD AND/OR PERSONAL INJURY.
2. ALWAYS USE PROTECTIVE EYEWEAR WHEN USING THIS PRODUCT: CONTACT WITH BATTERY ACID
MAY CAUSE BLINDNESS AND/OR SEVERE BURNS
3. KEEP OUT OF REACH OF CHILDREN!!
4. ALWAYS STORE BATTERY CLAMPS IN BUILT-IN HOLSTERS WHEN NOT IN USE. NEVER TOUCH BATTERY CLAMPS TOGETHER - THIS CAN CAUSE DANGEROUS SPARKS, POWER ARCING, AND/OR EXPLOSION.
FIRST AID:
1. SKIN:IF BATTERY ACID COMES IN CONTACT WITH SKIN, RINSE IMMEDIATELY WITH WATER, THEN
2. EYES: IF BATTERY ACID COMES IN CONTACT WITH EYES, FLUSH EYES IMMEDIATELY - FOR MINIMUM
OF 15 MINUTES SEEK IMMEDIATE MEDICAL ATTENTION.
WASH THOROUGHLY WITH SOAP AND WATER. IF REDNESS, PAIN, OR IRRITATION OCCURS, SEEK IMMEDIATE MEDICAL ATTENTION.
Page 7
1. INTRODUCTION
Congratulations on selecting the Vector® START-IT JUMPSTART SYSTEM & 12-VOLT DC POWER SUPPLY.
TM
Please read this guide carefully before use to ensure optimum performance and avoid damage to the unit or items that you are using it with.
The Vector® START-IT JUMPSTART SYSTEM & 12-VOLT DC POWER SUPPLY is a compact, durable and portable
TM
jumpstart system for vehicles and boats that have a standard 12-Volt battery system. This self-contained, rechargeable system will start most vehicles and boats without the need for a host vehicle or 110/120-volt AC power supply. It can also be used as a safe, portable source of 12-volt DC electric power in remote locations and/or emergency situations. It is ideal for use with Vector® 12-volt DC cordless, portable, rechargeable products and PowerForce® DC/AC Power Inverters. Use the START-IT TM to:
-Jumpstart
Any vehicle with a standard 12-volt DC battery system: boat, truck, car, airplane, RV, personal watercraft, snowmobile, tractor, etc.
-Operate: 12-volt DC
Fans, inflators, fluorescent work lights, cellular phones*, air compressors, spotlights, TVs, portable radios, cassette or CD players and more. *Can quick-charge a cellular phone by using the phone*s 1 2-volt DC adapter cord.
-Operate: Certain 11O/120-volt AC Accessories (requires DC to AC power inverter, sold separately)
The START-IT SYSTEM has an easy-to-read, series LED (Light Emitting Diode) charge indicators that show when the unit is fully charged, or the level of charge in the battery. Charge level can be viewed when the charge status button is pressed. A 12-volt DC cigarette lighter-type socket is provided for use with appliances that can operate from a vehicle cigarette lighter. This allows maximum portability and utility when the START-.IT is used in remote locations.
For maximum convenience, the START-IT can be recharged from any standard 110/120-volt AC or 12-volt DC power source using
TM
TM
TM
of
the built-in 12-volt socket and the appropriate charging/adapter cord. When pressed, the CHARGE STATUS button will show the battery*s power level status (from Low to Full). The green LED full indicator illuminates when the unit is fully recharged and charging can be discontinued. An ON/OFF switch operates the built in work/emergency light.
WARNING:
Lead-acid batteries generate hydrogen gas during normal operation. More gas is generated when the battery is charging. Hydrogen gas is: EXPLOSIVE !! POISONOUS TO BREATHE !! HIGHLY FLAMMABLE
To avoid an explosion and/or the possibility of being splashed with battery acid:
! NEVER allow the red and black clamps to touch each other or a common metal object. ! ONLY attempt to jumpstart a vehicle or boat in a WELL ventilated area. ! ALWAYS CONNECT THE RED (+) CLAMP TO THE POSITIVE (+) BATTERY TERMINAL FIRST. ! DO NOT CONNECT THE BLACK (-) CLAMP TO THE NEGATIVE (-) BATTERY TERMINAL. ! DO CONNECT THE BLACK (-) CLAMP TO A NON-MOVING METAL PART ON THE ENGINE.
CAUTIONS:
I. To avoid possible damage that may shorten the unit*s working life, protect this unit from direct sunlight, direct heat, and/or moisture.
2. This system is designed to be used ONLY on vehicles or boats with 12-volt DC battery systems.
3. This system is NOT designed to be used as a replacement for a vehicular battery.
RECOMMENDATIONS FOR OPTIMUM PERFORMANCE OF THE START-IT JUMPSTART SYSTEM: WARNING: NEVER insert anything other than the supplied power/recharging cords or recommended appliance power/recharging
cords into the charging/power sockets on this unit.
IMPORTANT: The safety ON/OFF switch should be in the OFF position when the unit is charging, or not in use.
TM
Page 8
2. USING THE START-IT AS A JUMPSTART SYSTEM
TM
CAUTIONS:
1. Before using this system to jumpstart any vehicle or boat, read and understand all instructions, safety tips, warnings, cautions and first aid information provided in this manual and on the product labeling. Additional important information may also be provided by the vehicle*s battery system manufacturer.
2. BE AWARE OF FIRST AID PROCEDURES BEFORE ATTEMPTING JUMPSTART PROCEDURE.
3. ALWAYS wear protective eyewear when working with a lead acid-type battery.
4. DO NOT smoke or use inflammable items (matches, cigarette lighters, etc.) while working on a vehicle ‘s battery system.
5. When using this vehicle in proximity to the vehicle ‘s battery and engine, stand the unit on a flat, stable surface, and be sure to keep all cords and cables well away from any moving parts.
6. Check unit periodically for wear and tear. Replace worn or defective parts immediately - contact Vector Customer Service Department at (954) 584-4446 ext. 19 or toll-free (866) 584-5504 or through our internet address: www.vectormfg.com
7. Do not attempt to jumpstart a frozen battery.
8. NEVER submerge this unit in water.
9. Do not wear vinyl clothing when jumpstarting a vehicle—friction can cause dangerous static electricity sparks. Remove all jewelry or metal objects—they can cause short circuits or react with battery acid to cause severe burns. Remove or secure any loose clothing items, and restrain long hair, before attempting jumpstart procedure.
WARNINGS:
1. Vehicles that have on-board computerized systems may be damaged if vehicle battery is jumpstarted. Before jumpstarting this type of vehicle, read the vehicle owner*s manual to confirm that external-starting assistance is advised.
2. Excessive engine cranking can damage the vehicle ‘s starter motor, if the engine fails to start after the recommended number of attempts, discontinue jumpstart procedure and look for other problems that may need to be corrected.
NOTE: IF AUDIBLE ALARM SOUNDS - DO NOT TURN ON SAFETY SWITCH! THEN REVERSE THE CABLE
CLAMP CONNECTIONS
2.1 EASY, STEP-BY-STEP JUMPSTARTING INSTRUCTIONS
1. Turn OFF vehicle ignition switch and all accessories (radio, a/c, lights, cell phone, etc.). Place vehicle in “park” and set the
emergency brake.
2. Make sure jumpstart safety power switch is turned OFF.
3. Follow procedure for negative or positive
grounded system, as follows: NEGATIVE GROUNDED SYSTEM (NEGATIVE BATTERY TERMINAL IS CONNECTED TO CHASSIS—MOST COMMON METHOD:
1. TO REMOVE BOOSTER CLAMPS FROM PROTECTIVE HOLSTER (FIG. 2): SIMPLY PULL DOWN ON CLAMP, (SHOULDER REST IS SPRING LOADED)—ROTATE TOP OF CLAMP OUTWARD WHILE YOU PULL DOWN—WHEN CLEAR OF CLAMP COVER REMOVE CLAMP TO REPLACE BOOSTER CLAMP INTO PROTECTIVE HOLSTER—RETURN CLAMP TO SHOULDER REST, ROTATE OUT AND PUSH DOWN THEN SLIDE CLAMP UP INTO PROTECTIVE COVER.
2. CONNECT POSITIVE (+) RED CLAMP TO
VEHICLE BATTERY ‘S POSITIVE TERMINAL
3. CONNECT NEGATIVE (-) BLACK CLAMP TO CHASSIS OR A SOLID, NON-MOVING, METAL
Page 9
VEHICLE COMPONENT OR BODY PART. NEVER CLAMP DIRECTLY TO NEGATIVE BATTERY
TERMINAL OR MOVING PART.
IF AUDIBLE ALARM SOUNDS - DO NOT TURN ON SAFETY SWITCH! REVERSE POLARITY OF CLAMP CONNECTIONS
POSITIVE GROUND SYSTEMS
NOTE: In the rare event that the vehicle to be started has a Positive Grounded System (positive battery
3a. Connect negative (-) black clamp to vehicle battery ‘s negative terminal.
terminal is connected to chassis): Replace step 3 above with the following steps, and then proceed to steps 4-6 below.
3b. Connect positive (+) red clamp to vehicle chassis or a solid, non-moving, metal vehicle component or body
part. DO NOT clamp directly to positive battery terminal or moving part.
If audible alarm sounds - do not turn on safety switch reverse polarity of clamp connections
4. Turn jumpstart system's power switch to ON position.
5. Start vehicle (do not turn key for longer than 5-6 seconds).
6. After vehicle starts, turn jumpstart system ‘s power switch to OFF position. Remove clamps (disconnect the negative (Black) jumper cable first; followed by the positive (Red) jumper cable) and replace them in the built-in storage holsters.
CAUTIONS:
1. If vehicle fails to start, leave vehicle ignition key turned OFF, disconnect the negative (-) clamp first, then the positive (+) clamp and discontinue jumpstarting procedure.
2. Recharge jumpstart system after each use.
WARNINGS:
1. ALWAYS disconnect the negative (Black) jumper cable first; followed by the positive (Red) jumper cable.
2. NEVER ALLOW RED AND BLACK CLAMPS TO TOUCH EACH OTHER OR ANOTHER COMMON METAL CONDUCTOR THIS COULD CAUSE DAMAGE TO THE UNIT AND/OR CREATE SPARKING/EXPLOSION HAZARD.
3. There is a risk of explosive gases being released when batteries are improperly charged or discharged. Failure to follow instructions may cause property damage, explosive hazard and/or personal injury.
4. ALWAYS USE PROTECTIVE EYEWEAR WHEN USING THIS PRODUCT: CONTACT WITH BATTERY ACID MAY CAUSE BLINDNESS AND/OR SEVERE BURNS.
5. Keep out of reach of children!!
6. ALWAYS store battery clamps in built-in holsters when not in use. Never touch battery clamps together—this con cause dangerous sparks, power arcing and/or explosion.
Page 10
FIRST AID:
!! Skin: If battery acid comes in contact with skin, rinse immediately with water, then wash thoroughly with soap and water. If redness,
pain, or irritation occurs, SEEK IMMEDIATE MEDICAL ATTENTION.
! Eyes: if battery acid comes in contact with eyes, flush eyes immediately— for minimum of 15 minutes SEEK
IMMEDIATE MEDICAL ATTENTION
3. CHARGING/RECHARGING
For maximum battery life, we recommend that the START-IT system be kept fully charged at all times. If the battery is allowed to
TM
remain in a discharged state, battery life may be shortened. Note: Recharging battery after each use will prolong battery life; frequent discharges between recharges will reduce battery life.
3.1 110/120-Volt AC Charging
IMPORTANT:
! MAKE SURE SAFETY ON/OFF SWITCH IS IN OFF POSITION DURING RECHARGING. ! Charge unit until full (can take up to 24 hours) ! Recharge unit fully after each use. ! Recharge unit every two months, when it has not been used.
1. Simply plug the 110/120-volt AC plug of the AC/DC adapter/charger cord into any standard
110/120-volt AC wall outlet.
2. Plug the 12-volt DC cigarette type plug into the 12-volt DC receptacle on the unit.
3. Charge this device for at (east 14-16 hours or until the FULL indicator lights when Charge Status Button is
pressed.
4. NOTE: The unit can be overcharged (which will shorten the life of the battery) — DO NOT charge with AC charging procedure for
more than 24 hours maximum.
5. When charging is completed, remove the power cord and store in a safe place.
NOTE: RECHARGE WHEN LESS THAN 4 RED LEDS LIGHT WHEN BATTERY STATUS PUSHBUTTON IS
PRESSED
3.2 12-Volt DC Charging
The START-IT system also comes with a DC/DC charging cord, for recharging the unit from the 12-volt DC cigarette lighter socket
TM
in a vehicle or boat. Note: This recharging method will NOT recharge the unit as effectively as recharging from a 110/120-volt AC outlet. The 12-volt DC recharging procedure is recommended only when it is necessary, as continued use of the 12-volt DC recharging procedure may shorten the battery system*s life.
WARNING: DO NOT RECHARGE FOR MORE THAN 3-4 HOURS MAXIMUM USING 12-VOLT DC METHOD.
1. NOTE: If unit is fully discharged, it is recommended that the vehicle being used for recharging with engine running while the unit
is being charged via the 12-volt DC method.
2. Insert one end of the DC/DC charging cord into the 12-volt DC cigarette lighter receptacle on the vehicle or boat.
Page 11
3. Insert the plug at the other end of this power cord into the 12-volt DC receptacle on the front panel of the unit.
4. Charge the unit until the green FULL indicator lights when Charge Status Indicator Button is pressed.
DO NOT EXCEED 3-4 HOURS MAXIMUM.
5. When charging is completed, remove the power cord and store in a safe place.
3.3 110/120 VAC Charging Using VECO7O 1.5 Amp Automatic Battery Charger
(purchased separately)
1. Install the charger*s DC wire with battery clips.
2. The jumpstarter has a high-current switch for turning the heavy-duty clamps ON and OFF. Make sure the Safety switch is turned
OFF.
3. Connect the POSITIVE (RED) DC Battery Clip to the RED POSITIVE jumpstarter clomp.
4. Connect the NEGATIVE (BLACK) DC Battery Clip to the BLACK NEGATIVE jumpstarter clamp.
5. Connect the charger to an AC outlet or extension cord rated at 18 AWG or larger.
6. Turn ON the Safety switch and observe the RED LED on the charger for proper operation.
7. Charge the START-IT until the green Charged LED lights when FULL Status Button is pressed. Then continue charging for
TM
another hour.
B. When charging is complete, Turn OFF the Safety switch.
9. Disconnect the charger from the AC outlet or extension cord.
10. Disconnect the charger*s battery clips from the jumpstarter*s clamps.
11. Store the charger as described in it*s Owner*s Manual.
12. Place the jumpstarter back into service.
3.4 Estimated Battery Life
Table I shows the relationship of the frequency of use between recharging and the expected number of discharge/recharge cycles
Table I Estimated Battery Life
AVERAGE NUMBER OF USES POTENTIAL TOTAL NUMBER (JUMPSTART OR DISCHARGES) OF JUMPSTART OR DISCHARGE CYCLES BETWEEN RECHARGES (LIFETIME OF UNIT BATTERY 1 1000+ 5 700+ 10 500+
Page 12
4. OPERATION AS A PORTABLE POWER SUPPLY
4.1 Operation as a 12-volt DC Power Supply
NOTE: Make sure that the unit ‘s safety ON/OFF switch is ALWAYS in the OFF position when using the 12-volt DC accessory outlet.
1. Lift up the cover of the unit ‘s 12-volt DC cigarette lighter-type receptacle (See Figure 1, #1).
2. Insert the 12-volt DC plug from the appliance into the receptacle on the unit.
3. Switch on the appliance, and operate as usual.
CAUTION: DO NOT USE THIS UNIT TO OPERATE APPLIANCES THAT DRAW MORE THAN 20 AMPS.
4.2 Estimated 12-Volt DC Usage Times
Table II shows the estimated 12-volt DC operation times when using a fully-charged system
Table II START-IT as a 12-Volt DC Power Supply
APPLIANCE TYPE CONSUMPTION (IN WATTS) TIME (IN HOURS) CELL PHONE 1 120 hrs. Talk Time
ESTIMATED POWER ESTIMATED USAGE
TM
FLUORESCENT LIGHT 4 30 RADIO, FAN, DEPTH FINDER 9 21 CAMCORDER, VCR, SPOTLIGHT 15 12 POWER TOOLS, BILGE PUMP 24 7 ELECTRIC COOLER 48 4 AIR COMPRESSOR, CAR VACUUM 80 1.5
NOTE: ALL TIMES ARE APPROXIMATE, AND BASED UPON FULLY CHARGED UNIT.
4.3 Operation as a 110 Volt AC Power Supply
Use with VECO4O (50 Watt), VECO23 (175 Watt), or VECO24 (400 Watt) Maxx® Power Inverters, sold separately. For estimated usage times, see chart provided with inverter.
1. Lift up the cover of the unit ‘s 12-volt DC cigarette lighter-type receptacle (See Figure 1, #1).
2. Insert the 1 2-volt DC plug from the power inverter into the receptacle on the unit.
3. Plug the appliance into the 110/120-volt AC receptacle on the inverter.
4. Switch on the appliance, and operate as usual.
CAUTION: DO NOT USE THIS UNIT TO OPERATE APPLIANCES THAT DRAW MORE THAN 200 WATTS OR EXCEED MAXIMUM WATTAGE OF INVERTER.
Page 13
5. EMERGENCY/WORK LIGHT
Bulb Replacement
You will need a small Phillips screwdriver
1. Replacement bulbs are available from Vector® Customer Service Department; call (954) 584-4446 EXT. 19 or toll-free (866) 584-
5504
2. Remove two Phillips screws from the lens.
3. Lift off the lens assembly.
4. Remove the burned-out bulb.
5. Replace with a new bulb (12-volt 0.4 amp Krypton bulb).
6. Snap the lens cover back into place, and replace Phillips screws.
6. BATTERY REPLACEMENT
IT IS RECOMMENDED THAT THE UNIT BE RETURNED TO VECTOR® CUSTOMER SERVICE FOR BATTERY REPLACEMENT: CONTACT (954) 584-4446 EXT. 19, OR TOLL-FREE (866) 584-5504
6.1 Battery Disposal
Contains a maintenance-free, sealed, non-spillable, lead acid battery, which must be disposed of properly. Some states require recycling — contact your local authority for information.
THIS UNIT CONTAINS A MAINTENANCE-FREE, SEALED, NON-SPILLABLE, LEAD ACID BATTERY WHICH MUST BE DISPOSED OF PROPERLY. SOME STATES REQUIRE RECYCLING. DISPOSAL QUESTIONS? IN USA, CALL 1 -877-288-7722.
WARNINGS:
. DO NOT DISPOSE OF THE BATTERY IN FIRE AS THIS MAY RESULT IN AN EXPLOSION. . BEFORE DISPOSING OF THE BATTERY, PROTECT EXPOSED TERMINALS WITH HEAVY-DUTY
ELECTRICAL TAPE TO PREVENT SHORTING (SHORTING CAN RESULT IN INJURY OR FIRE).
. DO NOT EXPOSE BATTERY TO FIRE OR INTENSE HEAT AS IT MAY EXPLODE.
7. SPECIFICATIONS
Model VECO21 ST Voltage 12 VDC Boost Power 400 Instantaneous Cranking Amps Peak Ampere Power 1200 Amps
Battery Type Non Spillable Sealed, lead- acid, rechargeable, Bulb 12-volt 0.4 Amp Krypton
Booster Cables #5AWG welding cable
Accessory Socket Self-Resetting Breaker 20 Amps Charging Cord 12-Volt DC Adapter/Charger 110/120-Volt AC
HEIGHT 11-3/4” (29.845CM) DEPTH 6-1/4” (15.875CM) WIDTH 11-5/8” (29.528CM) WEIGHT 18LBS. (8.164KG)
maintenance-free, 12-volt DC,19 Amp-hour
with 400 Amp copper clamps
(800mA, 12-Volt DC Output)
Page 14
This limited warranty program is the only one that applies to this product, and it sets forth all the responsibilities of Vector Manufacturing, Ltd., regarding this product. There is no other warranty, other than those described herein.
This Vector Manufacturing, Ltd. product is warranted, to the original purchaser only, to be free of defects in materials and workmanship for 120 days from the dote of purchase without additional charge. This warranty may be extended to years from date of purchase by paying an Extended Warranty fee (see below). The warranty does not extend to subsequent purchasers or users. Vector Manufacturing, Ltd. will not be responsible for any amount of damage in excess of the retail purchase price of the product under any circumstances. Incidental and consequential damages are specifically excluded from coverage under this warranty.
This product is not intended for commercial use. This warranty does not apply to accessories or damage to units from misuse or incorrect installation. Misuse includes wiring or connecting to improper polarity power sources. RETURN/REPAIR POLICY: Defective products, other than accessories, may be returned postage prepaid to Vector Manufacturing. Any defective product, other than accessories, that is returned to Vector Manufacturing within 30 days of the date of purchase will be replaced free of charge. If such a product is returned mare than 30 days but less than 120 days from the purchase dote, Vector Manufacturing will repair the unit or, at its option, replace it free of charge. If The Extended Warranty was activated, this repair or replacement period extends to three years from the purchase date, If the unit is repaired, new or reconditioned replacement parts may be used, at Vector Manufacturing*s option. A unit may be replaced with a new or reconditioned unit of the same or comparable design. The repaired or replaced unit will then be warranted under the terms of the remainder of the warranty period. The customer is responsible for the shipping charges on all returned items. During the warranty period, Vector Manufacturing, Ltd. will be responsible for the return shipping charges.
LIMITATIONS: This warranty does not cover accessories, bulbs, fuses and batteries, defects resulting from normal wear and tear (including chips, scratches, abrasions, discoloration or fading due to usage or exposure to sunlight), accidents, damage during shipping to our service facility, alterations, unauthorized use or repair, neglect, misuse, abuse, failure to fallow instructions for core and maintenance, fire, flood and Acts of God.
If your problem is not covered by this warranty, call our Technical Support Department at (954) 584-4446 or toll free at (866) 584- 5505 for general repair information and charges if applicable. You may also contact us through our website at www.vectormfg.com.
STATE LAW RIGHTS: This warranty gives you specific legal rights. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the exclusions or limitations stated herein may not apply. This warranty gives the purchaser specific legal rights; other rights, which vary from state to state, may apply. TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT: Contact Vector Manufacturing Technical Support by telephone, fax or mail. We suggest that you keep the original packaging in case you need to ship the unit. When returning a product, include your name, address, phone number, dated sales receipt (or copy) and a description of the reason for return and product serial number. After repairing or replacing the unit, we will attempt to return it to you within four weeks.
WARRANTY ACTIVATION: Please complete Warranty Activation Card and mail to Vector Manufacturing. If activating Additional Extended Two Year Warranty (total two years) enclose check or money order for $25.00 Enter “VEC021 ST” as Model and “Start-It” as Product Type.
All Vector Manufacturing, Ltd. products must be registered within (30) days of purchase to activate this warranty. Mail the completed registration farm, along with a copy of the original sales receipt to:
WARRANTY MUST BE PURCHASED WITHIN 3D DAYS OF PRODUCT PURCHASE DATE. WARRANTY IS NON­TRANSFERABLE AND NON-REFUNDABLE.
VECTOR 120 DAY/TWO YEAR LIMITED WARRANTY PROGRAM
WARRANTY REGISTRATION
VECTOR MANUFACTURING, Ltd.
4140 SW. 28th Way; Fort Lauderdale, Florida 33312
Please activate my Limited Warranty for Model VECO21ST
I hone enclosed a copy of the original sales receipt. Name___________________________________________________________________________________________________
_ Street Address_____________________________________________________________________________________________ City___________________________ State______________ Zip Code_______________________________________________ Phone_______________ Fax__________________
Item Purchased _________________________________ Date of Purchase__________________________________________ Store Where Purchased UPC_______________________ Number from package (12 digits)
All Vector Moeufocturieg, Ltd. products must be registered within (10) days of purchase to activate this warranty. Mail the completed registration form, along with a copy of the original sales receipt, to:
E-mail________________________________________________________
ATTN: CUSTOMER SERVICE
VECTOR MANUFACTURING, LTD.
4140 SW. 28th WAY
FT. LAUDERDALE, FL 33312
Loading...