Vector MAXX SST VEC049GM, MAXX SST VEC050GM, MAXX SST VEC051GM User's Manual & Warranty Information

16

VEC049GM
VEC050GM
VEC051GM

USER’S MANUAL

& WARRANTY INFORMATION

IMPORTANT SAFETY INFORMATION, SAVE THESE INSTRUCTIONS

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND
THIS INSTRUCTIONAL MANUAL. THIS MANUAL CONTAINS IMPORTANT
INFORMATION REGARDING THE OPERATION AND WARRANTY OF THIS
PRODUCT. PLEASE RETAIN FOR FUTURE REFERENCE.

www.vectormfg.com

4140 S.W. 30th Ave., Ft. Lauderdale, FL 33312

Toll Free: [phone]

MAXX SST

™

Portside Power Inverters

Converts 12 Volt DC to 110/120 Volt AC

Advanced MOSFET Technology

VEC050GM VEC051GM

VEC049GM

Power Inverter Model

*

.

Maximum Continuous Power 1000 watts 1500 watts 3000 watts

Surge Capacity (Peak Power) 2000 watts 3000 watts 6000 watts

No Load Current Draw (switch on) 1.7 amp 2.3 amp 2.8 amps

Maximum Efficiency (approx.) 90% 90% 90%

Input Voltage 10.5–15.5 VDC 10.5–15.5 VDC 10.5–15.5 VDC

Output Voltage 110/120 VAC 60 Hz 110/120 VAC 60 Hz 110/120 VAC 60 Hz

Low Voltage Alarm <10.6 VDC <10.6 VDC <10.6 VDC

Low Voltage Shutdown 10.0 VDC Auto Reset 10.0 VDC Auto Reset 10.0 VDC Auto Reset

Over Voltage Shutdown >15.5 VDC >15.5 VDC >15.5 VDC

Thermal Shutdown Auto Reset YES YES YES

Wave Form Modified Sine Wave (MSW) YES YES YES

Proper Cable Gauge (AWG) @ 6 FT. #3 #2 2/0

Proper Cable Gauge (AWG) @ 10 FT. #1 2/0 250 mcm

North American Standard Outlets 2 GFCI Protected Outlets 2 GFCI Protected Outlets 4 GFCI Protected Outlets

ANL Fuse Rating for Direct Hardwire 200 300 500

*For lengths greater than 10 FT., contact Vector's Technical Support, toll-free, at [phone]

1. These models feature multiple U ground 120 volt AC outlets

2. All of these inverters meet North American Standard Requirements.

3. All units feature Siemens Mosfet Power Transistors

SPECIFICA

TIONS

VEC049_50_51GM_Manual_041906 4/20/06 4:09 PM Page 16

Important Cable Information

Substantial power loss and reduced battery operating time results from inverters installed with cables that
are not able to supply full power. Symptoms of low battery power can result from cables that are either
excessively long or an insufficient gauge. Marine installations are also subjected to vibration and stresses
that exceed those of other mobile installations. Therefore, the installer/operator should be especially
aware of the requirements to maintain secure, tight, water-resistant electrical connections and to provide
for strain relief for DC cables and appliance wiring. Cable insulation must be the appropriate type for
the environment.

Read All Instructions Before Using This Power Inverter!

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

WARNINGS
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, EXPLOSION OR INJURY:

• NEVER connect to AC distribution wiring.

• Remove appliance plug from outlet strip or turn off inverter before working on the
appliance. Multiple outlet power strips with switches and circuit breakers only
interrupt power to the "hot" receptacle terminals. The "neutral" terminals remain
powered with respect to the "ground" terminals.

• NOT approved for ignition protected areas. Do not make any electrical connections
or disconnections in areas designated as IGNITION PROTECTED.

• This equipment employs components that tend to produce arcs or sparks. DO NOT
install in compartments containing batteries or flammable materials.

• Use this unit in properly ventilated areas ONLY.

• Do not open — there are no user-serviceable parts inside.

• Do not insert foreign objects into the outlets.

• Do not expose the unit to liquids, including water, rain or snow.

• This is not a toy — keep away from children.

CAUTIONS

• Always inspect battery supply connections and cables to ensure they are tight and that cable insulation
is not damaged.

• Do not use with positive ground electrical systems*. Reverse polarity connection will result in a blown
fuse and may cause permanent damage to the inverter and will void warranty.

*The majority of modern automobiles, RVs, trucks and boats are negative ground.

• Grounding the Neutral will cause the inverter to shut down. Do not operate this inverter if it is wet. Do
not install in engine compartment — install in a well ventilated area.

• This inverter has not been not tested for use with medical devices.

• Do not attempt to install or operate this unit while operating a motor vehicle.

APPLIANCE CAUTIONS

NEVER plug small appliances directly into the inverter outlets to recharge nickel-cadmium batteries.
Always use the charger provided with the appliance.

NEVER plug in battery chargers for cordless power tools if the charger carries a warning that dangerous
voltages are present at the battery terminals.

Certain chargers for small nickel-cadmium batteries can be damaged if plugged into the inverters. DO
NOT use inverters with the following two types of equipment.

1. Small, battery-operated appliances such as flashlights, cordless razors and toothbrushes that can
be plugged directly into an AC receptacle to recharge.

2. Battery chargers that have a warning label stating that dangerous voltages are present at the
battery terminals.

The majority of portable appliances do not have this problem. Most portable appliances use separate
transformers or chargers that plug into AC receptacles to supply a low DC or AC voltage output to the
appliance. If the appliance label states that the charger or adapter produces a low DC or AC voltage
output (30 volts or less), there should be no problem powering that charger or adapter.

Some fluorescent lamps may not operate properly with this type of inverter. If the bulb appears to be too
bright, or fails to light, do not use the lamp with this inverter.

Some fans with synchronous motors may slightly increase in speed (RPM) when powered by the inverter.
This is not harmful to the fan or to the inverter.

VEC049_50_51GM_Manual_041906 4/20/06 4:09 PM Page ii

1

TABLE OF CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

VEC049GM Functions and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

VEC050GM Functions and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

VEC051GM Functions and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

MAXX SST™Portside Power Inverter Safety Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Principle of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Appliance Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Appliance Consumption in Amps and Watts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Power Source Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Determining Battery Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Runtime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Protective Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Operating Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Marine Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connection To Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Operating Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Notes on Using the Remote Control (sold separately) . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Fuse Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Common Audio/Visual Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Resetting the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Fault Protection and Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

INTRODUCTION

Thank you for purchasing a

Vector MAXX SST™Portside Power Inverter.

Please read this guide carefully before use to ensure optimum performance and to
avoid damage to this product.

This Power Inverter is configured with the latest Soft Start Technology (SST) and
supplies continuous power in the form of 120 volt AC outlets to run most household
or electronic appliances. Before introduction of SST, high start-up currents from large
inductive loads could shut down an inverter. SST improves inverter operation by:

• Gradual voltage ramp-up during inver ter start-up, eliminating failed cold starts
under load.

• Output that momentarily dips in voltage and quickly recovers to allow large
motorized loads to start, eliminating most shutdowns from momentary overloads.

• A new technology that cools the power transistors more efficiently, and, combined
with Soft Start, dramatically increases reliability and life of the product.

Added safety features include automatic shutdown and a low battery alarm to prevent
damage to your battery.

FEATURES

Portside Power Inverters are supplied with:

• Rubber grommets for vibration immunity and secure bulkhead mounting.

• Grounding terminals for electrical safety.

TWO YEAR LIMITED WARRANTY PROGRAM

This limited warranty program is the only one that applies to this product, and it sets forth all the
responsibilities of Vector Products, Inc., regarding this product. There is no other warranty, other than
those described herein. Any implied warranty of merchantability or fitness for a particular purpose on
this product is limited in duration to the duration of this warranty.

This Vector Products, Inc. product is warranted, to the original purchaser only, to be free of defects in
materials and workmanship for two years from the date of purchase without additional charge. The
warranty does not extend to subsequent purchasers or users. Manufacturer will not be responsible for
any amount of damage in excess of the retail purchase price of the product under any circumstances.
Incidental and consequential damages are specifically excluded from coverage under this warranty.

This product is not intended for commercial use. This warranty does not apply to damage to units from
misuse or incorrect installation/connection. Misuse includes wiring or connecting to improper polarity
power sources.

RETURN/REPAIR POLICY: Defective products may be returned to manufacturer. Any defective product
that is returned to manufacturer within 30 days of the date of purchase will be replaced free of charge.
If such a product is returned more than 30 days but less than two years from the purchase date,
manufacturer will repair the unit or, at its option, replace it, free of charge.

If the unit is repaired, new or reconditioned replacement parts may be used, at manufacturer’s option.
A unit may be replaced with a new or reconditioned unit of the same or comparable design. The
repaired or replaced unit will then be warranted under the terms of the remainder of the warranty
period. The customer is responsible for the shipping charges on all returned items. During the warranty
period, manufacturer will be responsible for the return shipping charges to the customer in the United
States.

LIMITATIONS: This warranty does not cover accessories, such as charging adapters, bulbs, fuses and
batteries, damage or defects resulting from normal wear and tear (including chips, scratches, abrasions,
discoloration or fading due to usage or exposure to sunlight), accidents, damage during shipping to our
service facility, alterations, unauthorized use or repair, neglect, misuse, abuse, failure to follow
instructions for care and maintenance, fire, flood and Acts of God.

If your problem is not covered by this warranty, call our Technical Support Department at (954) 584­4446 or toll free at [phone] for general repair information and charges if applicable. You may
also contact us through our website at www.vectormfg.com.

STATE LAW RIGHTS: This warranty gives you specific legal rights. Some states do not allow limitations
on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential
damages, so the exclusions or limitations stated herein may not apply. This warranty gives the purchaser
specific legal rights; other rights, which vary from state to state, may apply.

TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT: Contact Technical Support by telephone, fax
or mail (see below). We suggest that you keep the original packaging in case you need to ship the unit.
When returning a product, include your name, address, phone number, dated sales receipt (or copy)
and a description of the reason for return and product serial number. After repairing or replacing the
unit, we will make every effort to return it to you within four weeks.

WARRANTY ACTIVATION: Please complete Warranty Activation Card and mail to Vector Products, Inc..
Enter the appropriate model number as Model and “MAXX SST

™

Portside Power Inverter” as Product
Type. All Vector products must be registered within 30 days of purchase to activate this warranty. Mail
the completed registration form, along with a copy of the original sales receipt, to:

ATTN.: CUSTOMER SERVICE

4140 SW 30th Ave., Ft. Lauderdale, FL 33312

• TOLL FREE: (866 ) 584-5504 • FAX: [phone] •

WARRANTY IS NON-TRANSFERABLE.

BD041206

© 2006 VECTOR PRODUCTS, INC.

MADE IN CHINA

VEC049_50_51GM_Manual_041906 4/20/06 4:09 PM Page iv