Vector GL1000, GL1010, GL1000 Series User Manual

Download

User Manual GL1000/GL1010

Version English

– Compact Logger

2.3

Imprint

Vector Informatik GmbH Ingersheimer Straße 24

Vector reserves the right to modify any information and/or data in this user documentation without notice. This documentation nor any of its parts may be reproduced in any form or by any means without the prior written consent of Vector. under law, all technical data, texts, graphics, images and their design are protected by copyright law, various international other applicable law. Any unauthorized use may violate copyright and other applicabl © All rights reserved. 80353

-70499 Stuttgart

To the maximum extent permitted

e laws or regulations.

treaties and

User Manual GL1000/GL1010 – Compact Logger Table of Contents

Table of Contents

1 Introduction 3

1.1 About this User Manual 4

1.1.1 Certification 5

1.1.2 Warranty 5

1.1.3 Support 5

1.1.4 Trademarks 5

2 GL1000/GL1010 – Compact Logger 7

2.1 General Information 8

2.2 Features 9

2.2.1 Connectors 9

2.2.2 SD/SDHC Memory Card 10

2.2.3 Serial Number 11

2.2.4 LED Display 12

2.2.5 Digital Input/Output 13

2.2.6 Analog Inputs 13

2.2.7 Serial Interface 14

2.2.8 Real-Time Clock with Battery 14

2.2.9 Beep 15

2.2.10 Wake-up / Sleep 16

2.2.11 CCP/XCP 16

2.2.12 Diagnostics 17

2.2.13 LOGview Control 17

2.3 Operating Modes 18

2.4 Piggybacks 19

2.5 Technical Data 21

2.6 Included with Delivery 22

2.7 Accessories 22

3 Installation Configuration Programs 23

3.1 Overview 24

3.2 Installation Vector Logger Configurator 24

3.2.1 Requirements 24

3.2.2 Setup 24

3.2.3 Overview 25

3.2.4 Quick Start 26

3.3 Installation G.i.N. Configuration Program 27

3.3.1 Requirements 27

3.3.2 Setup 27

3.3.3 Overview 28

3.3.4 Quick Start 29

4 Index 31

User Manual GL1000/GL1010 – Compact Logger Introduction

1 Introduction

In this chapter you find the following information:

1.1 About this User Manual page 4 Certification Warranty Support Trademarks

Introduction User Manual GL1000/GL1010 – Compact Logger

The user manual provides you the following access helps:

> At the end of the user manual you will find an index.

regarding utilized spellings and symbols.

File

Save

Source code

Here you can find additional information.

Step-by-step instructions provide assistance at these points.

Instructions on editing files are found at these points.

1.1 About this User Manual

To find information quickly

> At the beginning of each chapter you will find a summary of the contents,

> In the header you can see the current chapter and section,

> In the footer you can see to which version the user manual replies,

Conventions

In the two following charts you will find the conventions used in the user manual

Style Utilization

bold

Windows Legally protected proper names and side notes.

Hyperlink Hyperlinks and references.

<STRG>+<S> Notation for shortcuts.

Blocks, surface elements, window- and dialog names of the software. Accentuation of warnings and advices.

[OK] Push buttons in brackets

File name and source code.

Notation for menus and menu entries

Symbol Utilization

Here you can find additional information and hints that eases the work with the loggers.

This symbol calls your attention to warnings.

Here is an example that has been prepared for you.

This symbol warns you not to edit the specified file.

- 4 - Version 2.3 © Vector Informatik GmbH

User Manual GL1000/GL1010 – Compact Logger Introduction

Management System

The ISO standard is a globally recognized standard.

the contents and for damages which may result from the use of this documentation.

or you write an email to support@vector.com.

trademarks

trademarks of their respective owners.

1.1.1 Certification

Certified Quality

Vector Informatik GmbH has ISO 9001:2008 certification.

1.1.2 Warranty

Restriction of warranty

We reserve the right to modify the contents of the documentation or the software without notice. Vector disclaims all liabilities for the completeness or correctness of

1.1.3 Support

You need support? You can get through to our hotline at the phone number

+49 711 80670-200

1.1.4 Trademarks

Protected

All brand names in this documentation are either registered or non registered

User Manual GL1000/GL1010 – Compact Logger GL1000/GL1010 – Compact Logger

2 GL1000/GL1010 – Compact Logger

In this chapter you find the following information:

2.1 General Information page 8

2.2 Features page 9 Connectors SD/SDHC Memory Card Serial Number LED Display Digital Input/Output Analog Inputs Serial Interface Real-Time Clock with Battery Beep Wake-up / Sleep CCP/XCP Diagnostics LOGview Control

2.3 Operating Modes page 18

2.4 Piggybacks page 19

2.5 Technical Data page 21

2.6 Included with Delivery page 22

2.7 Accessories page 22

GL1000/GL1010 – Compact Logger User Manual GL1000/GL1010 – Compact Logger

configuration program. The installation is described in chapter 3.

eliminated.

Support.

all GL1000/GL1010.

2.1 General Information

GL1000 The GL1000 is a data logger with USB interface which processes CAN messages

with either 11-bit or 29-bit identifiers and LIN messages. Furthermore, received messages and analog values can be logged on an inserted SD card. The configuration of the logger is done with the Vector Logger Configurator or the G.i.N.

GL1010

The GL1010 is equivalent to the GL1000 and differs only in the design of the housing and the connections (watertight according to IP65). The SD card is located in the housing and is no longer accessible from the outside. The opening for the speaker is

Note: Please note that the housing of the GL1010 must not be opened under any

circumstances, since otherwise the IP65 protection class of the data logger is no longer guaranteed. The SD/SDHC card, the piggybacks, and the battery may only be replaced by Vector Informatik GmbH. For more information, please contact the Vector

Figure 1 – GL1000 (left), GL1010 (right)

Info: Due to the openings in the housing for the LED, leak tightness may not be

guaranteed if the label is damaged.

The loggers from serial number 5000 (GL1000) respectively 102000 (GL1010) are of

the newest hardware revision. Firmware versions 1.49 or higher are required for operation (included in the Vector Logger Configurator version 2.5 SP5 or higher).

Configurations (COD files) generated with older versions have to be recompiled with the newer Vector Logger Configurator. The recompiled configuration is compatible to

- 8 - Version 2.3 © Vector Informatik GmbH

User Manual GL1000/GL1010 – Compact Logger GL1000/GL1010 – Compact Logger

> SD card slot (externally accessible for GL1000)

pin assignment

to the included connection cable.

the power supply ground.

transceiver TJA1043.

2.2 Features

2.2.1 Connectors

General information The loggers have the following connectors:

> USB connector: data transfer between PC and logger

> HD DSUB25 connector containing:

2 CAN channels 2 LIN channels 2 digital inputs/outputs 4 analog inputs Battery and ground Ignition

DSUB25

The pins of the HD DSUB25 connector have the following meaning. The colors refer

Pin Assignment Color Pin Assignment Color

1 Battery white 14 Opt3 N.C.

2 RS232 Rx white/green 15 CAN1 High yellow

3 RS232 Tx N.C. 16 CAN1 Low green

4 GND brown 17 Opt4 N.C.

5 Opt1 N.C. 18 Opt5 N.C.

6 I/O 1 white/yellow 19 CAN2 High grey

7 GND brown 20 Wake black

8 I/O 2 brown/yellow 21 CAN2 Low pink

9 AnaIn 1 grey/pink 22 GND brown

10 AnaIn 2 red/blue 23 LIN 1 lilac

11 AnaIn 3 blue 24 LIN 2 red

12 AnaIn 4 brown/green 25 Opt6 N.C.

13 Opt2 N.C.

The three GND pins are connected together internally and have the same potential as

Note: Transceivers with wake-up capability are supplied directly from the supply

voltage of the logger. During logger start, for the TJA1041 and TJA1054 transceivers the supply voltage must not exceed 27 V in order to not damage the transceivers. After start and during operation for these transceivers a supply voltage of maximum 30 V can be applied.

For a supply voltage of 27 V up to 30 V CAN we recommend for CAN high-speed the

GL1000/GL1010 – Compact Logger User Manual GL1000/GL1010 – Compact Logger

wires. At the same time the EMC properties are improved.

ground (GND) pins of the two voltage supplies must be connected.

connector

connected.

These cards are listed below.

> Cactus Industrial Grade 2 GB (KS 2GRI-800), some higher start-up time

> SanDisk Industrial XT 32 GB (SDSDAF-032G-XI SD)

mechanical damage!

Connection cable The included connection cable has open wire ends. If single wires are not used, it is

recommended to terminate them. This prevents short circuits between the open

Info: The connection cable does not match IP65.

Caution: It is recommended to connect the logger to the same voltage supply (e.g.

battery of the vehicle) as the vehicle or test equipment, respectively.

If two different voltage supplies are used for the logger and the test equipment, the

GL1010 USB

It is recommended to protect the USB connector with a cap if no USB cable is

2.2.2 SD/SDHC Memory Card

SD and SDHC cards The logger supports industrial grade SD cards up to 2 GB. From serial number 220

and higher also industrial grade SDHC cards are supported (firmware V1.08 and higher is required).

For the proper use only the industrial grade cards released by Vector may be used.

Recommended SD cards

Recommended SDHC cards

The following SD cards with industrial grade are recommended (see also section 2.5):

> Xmore industrial 2 GB (SD-2G0-XIWE2, SD-2G0-XIWE21, SD-2G0-XIE82)

The following SDHC cards with industrial grade are recommended (see also section 2.5):

> Xmore industrial 4 GB (SD-4G0-XIE6, SD-4G0-XIWE21, SD-4G0-XIE23)

> Xmore industrial 8 GB (SD-8G0-XIE6, SD-8G0-XIWE21, SD-8G0-XIE23)

> Xmore industrial 16 GB (SD-16G-XIE23)

> Cactus Industrial Grade 4 GB (KS 4GRI-800)

> Cactus Industrial Grade 8 GB (KS 8GRI-800)

GL1000: Inserting and removing SD card

- 10 - Version 2.3 © Vector Informatik GmbH

The GL1000 has a push-and-pull card holder for inserting and removing the SD card. To insert the SD card, push it in until the locking mechanism engages securely. To remove the SD card, push it slightly into the card holder until it unlocks. Now, release the SD card. The card moves from its original position and can now be removed.

Do not pull the SD card from the card holder forcefully, since this could cause

User Manual GL1000/GL1010 – Compact Logger GL1000/GL1010 – Compact Logger

removed or replaced.

GmbH. For more information, please contact the Vector Support.

file system.

configuration and upload logging files.

program.

GL1010: SD card The SD card is already contained in the housing of the GL1010 and cannot be

Note: Please note that the housing of the GL1010 must not be opened under any

circumstances, since otherwise the IP65 protection class of the data logger is no longer guaranteed. The SD/SDHC card may only be replaced by Vector Informatik

Data transfer

The logged data can be downloaded from the SD/SDHC card in the GL1000/GL1010 or in an SD/SDHC card reader. In both cases for the download and the conversion the configuration program is required. It is not possible to access the logged data on the memory card directly through the Windows Explorer because of the logger’s own

Note: Laptops with an integrated SD card reader rarely cannot identify SD cards with

a logger specific file system. In this case please use an external USB card reader.

Caution: A formatted SD/SDHC card has to be empty before inserting it in the

logger! The configured logger will delete all files if a formatted memory card is not empty!

The logger deletes the W indows files and the file system on the memory card on start of logging mode if they exist. The logger uses its own file system that cannot be seen in the Windows Explorer. It is required to use a configuration program to download a

2.2.3 Serial Number

Serial number The serial number is stored in the logger and is copied to the SD card after download

of the configuration and start in logging mode. The configuration program reads out the serial number of the logger in the configuration mode. The serial number is displayed correctly, if an SD card is inserted and the logger was at least one time in the logging mode with this SD card. If this SD card is inserted in another logger and the logger is not started in logging mode afterwards, the serial number of the first logger will be displayed in the configuration

GL1000/GL1010 – Compact Logger User Manual GL1000/GL1010 – Compact Logger

used to display different states. LED USB indicates the USB connection to the PC.

Note, that this LED is not programmable.

Off

All other cases

LEDs 1–4

In the following situations in the Logging mode the display of LEDs 1–4 is fix.

2.2.4 LED Display

LED display The logger has five LEDs. LED 1 to LED 4 are freely programmable. They can be

LED Color Programmable

LED 1 Green Yes

LED 2 Yellow Yes

LED 3 Red Yes

LED 4 Red Yes

LED USB Green No

LED USB

This LED displays the state of the USB connection between the logger and the PC.

State Meaning

On USB connected and SD card inserted. The logger is

registered on the PC and ready for data transfer via USB.

Note:

The LED will be on (determined by the system) if the SD card is removed in this state.

Slow blinking (1 Hz)

Fast blinking Data transfer

USB connected, but SD card is not inserted. The logger is registered on the PC. Due to missing SD

card no data transfer is possible.

Note:

If an SD card is inserted in this state, the LED will be switched on. The logger is now ready for data transfer.

State Meaning

Running light over LEDs 1–4

Simultaneous blinking of LEDs 1–4

- 12 - Version 2.3 © Vector Informatik GmbH

At the first start in Logging mode after a configuration download from PC a running light over LEDs 1–4 indicates the internal update and setup of ring buffers on the memory card (firmware up to 0.96).

Fault due to missing or defective SD card.

User Manual GL1000/GL1010 – Compact Logger GL1000/GL1010 – Compact Logger

outputs.

Technical data

input with GND the status is set to Low (FALSE).

connect it between the pin of the digital output and the battery.

separately.

Technical data

channel.

2.2.5 Digital Input/Output

Digital IO The logger supports two pins which can be used either as digital inputs or as digital

Operating voltage range

0 V…36 V

Pull-up resistor

Using as input A digital input can be used e.g. as external trigger.

In unconnected state the digital inputs are set to High (TRUE). After connecting the

Threshold Low → High

Threshold High → Low

Sampling rate

Using as output

When used as a digital output, the pin is connected to GND when the output is switched on (so called “low side switch”). To switch a consumer it is necessary to

Current when switched on

Circuit time

10 kΩ to 5 V

1.9 V

0.5 V

1 kHz

Max. 500 mA

Typ. 1ms

2.2.6 Analog Inputs

Analog inputs The logger has four independent analog channels which can be configured

Averaging

Voltage range

Resolution

Precision

Sampling rate

Type

Input resistance

Reverse-polarity protection

It is possible to average the measured analog inputs over a defined sampling period between 1 kHz and 1 Hz. E.g. for a 1 Hz sampling frequency, the measured values are averaged over the last second. The internal sampling rate is 1 kHz for each

0 V … 16 V

10 bit

1 %

Max. 1 kHz

Single-ended to ground

155.6 kΩ

-50 V … +50 V

GL1000/GL1010 – Compact Logger User Manual GL1000/GL1010 – Compact Logger

CAN messages.

the logged data.

be inserted). After setting the real-time clock the logger is switched off.

> GL1010 up to and including serial number 028081-100105

that the time will be applied.

newer serial numbers than those indicated above.

T = -40°C to +40°C in the rest of the time

more information, please contact the Vector Support.

2.2.7 Serial Interface

RS232 The serial interface with the Rx and Tx lines is a logging interface only. The baudrate

of the interface can be configured. Received data can be stored on the SD card as

Info: The serial interface cannot be used to download a configuration or upload

logging data.

2.2.8 Real-Time Clock with Battery

Real-time clock The GL1000/GL1010 has an internal real-time clock, which is battery supplied, and

thus continues running even if the logger is disconnected from power supply. The real-time clock inside the logger is required to store the date and time together with

It is recommended to set the real-time clock before first logging.

The configuration of the clock is done with the configuration program (SD card must

Older logger under Windows 7, Windows 8 and Windows 10

The affected loggers must be connected to the USB and be supplied with power via

Under Windows XP, the USB connection is adequate for setting the time for all

Battery The internal battery supplies the real-time clock only. The battery has a typical

GL1010: Battery

When the real-time clock of older GL1000/GL1010 is set under Windows 7 / Windows

8 / Windows 10, the concluding ejection of the logger must be performed manually for

hardware reasons. This pertains to the following serial numbers:

> GL1000 up to and including serial number 028069-001339

the DSUB25 connector before the time is set. After the time is set with the configuration program, the USB connection must be disconnected immediately so

GL1000/GL1010; the same applies under Windows 7 / Windows 8 / Windows 10 for

durability of approximately 5-10 years under the following conditions:

T = +40°C to +80°C for at most 40 hours per week

Please note that the housing of the GL1010 must not be opened under any circumstances, since otherwise the IP65 protection class of the data logger is no longer guaranteed. The battery may only be replaced by Vector Informatik GmbH. For

- 14 - Version 2.3 © Vector Informatik GmbH

User Manual GL1000/GL1010 – Compact Logger GL1000/GL1010 – Compact Logger

> This must be done very cautiously and carefully.

The battery is exchanged as follows:

sure the spring has contact to the new battery after replacement.

guide rail with the piggybacks facing up.

8. Please also attach the two black decorative caps.

in Germany).

trigger. Triggers and beep can be defined using the configuration program.

speaker is only audible to a limited extent in the GL1010.

GL1000: Replacing battery

The battery of the GL1000 can be is exchanged after life cycle end.

Notes:

> First read the installation instruction completely.

> The case has to be opened to exchange the piggybacks.

Caution: When performing this operation be sure not to touch the top or bottom of

the boards (logger main board or piggybacks).

1. First remove the two black decorative caps and the screws from the bottom cover of the GL1000. The bottom cover contains the DSUB25 connector. Carefully pull out the main circuit board.

2. You will find mounting location almost at the center of the main circuit board, partly covered by the piggybacks (see green circle in Figure 2).

3. Remove the piggybacks for easier access to the battery.

4. Remove the battery carefully from the mounting location.

5. Insert the replacement battery. Look out for the correct polarity, + must be on top. Please handle the contact spring with care. Do not bend it too much and make

6. Place the GL1000 main board back in the housing verifying that it is inserted properly. This operation involves placing the housing on a table with its back side (side with the bar code) facing up. Then the main board is inserted into the lower

7. It should be possible to slide the main board in the housing up to a few millimeters from the end without forcing it in. Close the housing by applying light pressure, and then secure it with the appropriate screw fasteners. The screws should be secure but not excessively tight.

Dispose of the removed battery according to the applicable laws (e.g. the Battery Law

2.2.9 Beep

Beep The GL1000/GL1010 has a speaker that acoustically alerts the user e.g. in case of a

Because the opening in the housing has been eliminated, the signal tone of the

GL1000/GL1010 – Compact Logger User Manual GL1000/GL1010 – Compact Logger

> wake-up timer via real-time clock

support the wake-up functionality on CAN (see section 2.4 Piggybacks).

compatible busses or the busses are not connected.

received for a defined time. This time can be configured (max. 18000 s = 5 h).

license also includes the Seed & Key support.

FAQ

2.2.10 Wake-up / Sleep

Wake-up The GL1000/GL1010 starts after power on. A sleeping logger wakes up

> after reception of a CAN message

> after reception of a LIN message

> positive edge on the wake line (clamp 15)

The logger has to be equipped with CAN transceivers with wake-up capability to

The wake-up line resists the full board voltage. If the GL1000 is supplied from clamp

30, the wake-up line can be connected with clamp 15. Thereby the GL1000 will be woken up immediately at switching on the ignition even if no activity is on the wake-up

Sleep

The logger can be configured to go to sleep mode if no CAN and LIN messages are

2.2.11 CCP/XCP

Overview The GL1000/GL1010 supports the recording of CCP/XCP data in DAQ and polling

mode. The A2L file is inserted directly in the Vector Logger Configurator and the signals to be measured are selected.

For ECUs which are protected via Seed & Key procedure CANape is also required to program the Seed & Key algorithm and create an SKB file containing this algorithm. This SKB file is added to the logger configuration.

CCP/XCP is available as option. The license must be installed in the logger. The

Measurement mode

Supported CCP version

Supported XCP version

Configuration

DAQ (data aquisition) mode, polling mode

CCP 2.0 und CCP 2.1

XCP 1.0 and higher

Vector Logger Configurator V2.5 or higher CANape for Seed & Key only

Alternative:

CANape V8.0 or higher for DAQ mode, Seed & Key CANape V13.0 or higher for polling mode

A2L file

Number of ECUs

- 16 - Version 2.3 © Vector Informatik GmbH

Direct import in Vector Logger Configurator Import in CANape

Multiple ECUs possible

still available

User Manual GL1000/GL1010 – Compact Logger GL1000/GL1010 – Compact Logger

Overview

The GL1000/GL1010 supports the logging of diagnostic data via CAN bus.

analysis is supported in CANoe/CANalyzer.

FAQ

Overview

The GL1000/GL1010 supports the connection of a LOGview display.

LOGview.

the LTL configuration.

possible that can be selected depending on the use case.

2.2.12 Diagnostics

The diagnostic descriptions (CDD, ODX, PDX, MDX) are read into the Vector Logger

Configurator. These files are necessary to set the communication parameters and to

select the diagnostic service requests that would be sent on different events. The

CDD (CANdela diagnostic descriptions) up to V7.1

Diagnostic descriptions

ODX/PDX V2.0.1 and V2.2.0 MDX V3.0

Supported transport protocol

Supported addressing modes

Supported diagnostic

ISO-TP

Normal Normal fixed Extended

KWP2000, UDS

protocols

Seed & Key

Number of ECUs

Not supported

Several ECUs on different CAN buses possible

2.2.13 LOGview Control

The connection is made via CAN channel CAN2 thus CAN2 cannot longer be used

unlimited. CAN2 can be used additionally for the logging of CAN messages of a CAN network, if the CAN network will not be disturbed by CAN messages (standard IDs 0x400 – 0x43F) that are transmitted between logger and display. Precondition therefor is that the network uses the required LOGview baud rate of 500 Kbit/s. The required bus terminating resistor of 120 Ohm is installed internally within the

The CAN data traffic between GL1000/GL1010 and LOGview will not be logged and it

will not influence the sleep behavior of the logger. The data traffic is also “hidden” for

Electrical connection

For the electrical connection of the LOGview to the logger, a 5-pin Binder connector must be wired with the DSUB25 connector of the logger. Therefor two variants are

GL1000/GL1010 – Compact Logger User Manual GL1000/GL1010 – Compact Logger

Variant 1

The display is on if the ignition (clamp 15) is on.

DSUB25 connector from the vehicle.

Variant 2

The display is on if the logger is awake.

clamp 30 of the vehicle

be identified by the active background illumination.

programming (see LTL user manual).

USB connection and power supply respectively.

SD card can be uploaded to the PC.

DSUB25 connector.

LOGview Pin Color Description GL1000 DSUB25 Pin

1 gray On/Off N.C.

2 brown GND, together with

vehicle ground

3 yellow CAN High 19 (CAN2 High)

4 green CAN Low 21 (CAN2 Low)

5 white V

, together with

batt

clamp 15 of the vehicle

4 (GND)

20 (Wake)

Additionally the GL1000/GL1010 must be supplied at least via PIN 1 (battery) of the

LOGview Pin Color Description GL1000 DSUB25 Pin

1 gray On/Off 6 (I/O 1)

2 brown GND, together with

4 (GND)

vehicle ground

3 yellow CAN High 19 (CAN2 High)

4 green CAN Low 21 (CAN2 Low)

5 white V

, together with

batt

1 (battery)

This variant requires an additional resistor of 33 kOhm between pin 4 and 6 of the DSUB25 connector. Without this resistor the LOGview is permanently on, which can

Additionally with this variant the LOGview can be switched on and off via LTL

2.3 Operating Modes

Overview The GL1000/GL1010 supports two operating modes, which are switched by using the

USB connection Voltage supply Mode

yes optional Configuration mode

no yes Logging mode

Configuration mode

In the Configuration mode the logger can be configured with the configuration program. The configuration can be downloaded to the logger. Logging data from the

Logging mode

The Logging mode enables the PC independent usage of the logger and allows the logging of CAN, LIN and analog values. For this case the logger must be unplugged from the USB connector of the PC. The voltage supply is done externally by the

- 18 - Version 2.3 © Vector Informatik GmbH

User Manual GL1000/GL1010 – Compact Logger GL1000/GL1010 – Compact Logger

Available piggybacks for the GL1000 series:

Piggyback 1055 as successor of Piggyback 1054

30 V can be applied.

the GL1000/GL1010. Therefore LIN piggybacks are not needed.

logger is supplied with 24 V, the reference value for LIN is also 24 V.

GmbH. For more information, please contact the Vector Support.

> This must be done very cautiously and carefully.

2.4 Piggybacks

Piggybacks

A piggyback is a plug-in PC-board which implements the interconnection of the logger to a specific CAN bus by the use of various transceivers. The piggybacks are also used in other loggers.

CAN Piggyback Transceiver Description Wake-up

Piggyback 10431 TJA1043 CAN High-speed Yes

Piggyback 10422 TJA1042 CAN High-speed No

Piggyback 1050 TJA1050 CAN High-speed No

Piggyback 10553 TJA1054 CAN Low-speed Yes

Piggyback Single Wire TLE6255G CAN Single Wire Yes

Piggyback Truck Trailer WABCO CAN Truck&Trailer Yes

Piggyback 1043 as successor of Piggyback 1041

Piggyback 1042 as successor of Piggyback 251

Note: Transceivers with wake-up capability are supplied directly from the supply

LIN transceiver

LIN level

GL1010: Piggybacks

GL1000: Replacing piggybacks

The LIN transceivers TJA1020/TJA1021 are already mounted on the main board of

The LIN transceivers are supplied from the supply voltage. On this way reference voltage for the LIN levels and supply voltage have the same value. For example if the

Please note that the housing of the GL1010 must not be opened under any circumstances, since otherwise the IP65 protection class of the data logger is no longer guaranteed. The piggybacks may only be replaced by Vector Informatik

The CAN piggybacks can be exchanged for the GL1000. The installed piggybacks are automatically detected (“plug & play”).

Notes:

> First read the installation instruction completely.

> The case has to be opened to exchange the piggybacks.

Caution: When performing this operation be sure not to touch the top or bottom of

the boards (logger main board or piggybacks).

GL1000/GL1010 – Compact Logger User Manual GL1000/GL1010 – Compact Logger

Now proceed as follows:

3. Remove the piggyback carefully from the mounting location.

7. Please also attach the two black decorative caps.

1. First remove the two black decorative caps and the screws from the bottom cover of the GL1000. The bottom cover contains the DSUB25 connector. Carefully pull out the main circuit board.

2. You will find the mounting location for channel 1 close to the center of the main circuit board and the mounting location for channel 2 close to the edge of the main circuit board. The locations are marked red in Figure 2.

4. Insert the replacement piggyback. When doing this please make sure that the single and dual-row connectors are not laterally shifted.

5. Place the GL1000 main board back in the housing verifying that it is inserted properly. This operation involves placing the housing on a table with its back side (side with the bar code) facing up. Then the main board is inserted into the upper guide rails with the piggyback facing up.

6. It should be possible to slide the main board in the housing up to a few millimeters from the end without forcing it in. Close the housing by applying light pressure, and then secure it with the appropriate screw fasteners. The screws should be secure but not excessively tight.

Layout GL1000/GL1010

Figure 2 – Layout GL1000/GL1010

- 20 - Version 2.3 © Vector Informatik GmbH

User Manual GL1000/GL1010 – Compact Logger GL1000/GL1010 – Compact Logger

start-up time.

2.5 Technical Data

PC interface

Channels

Analog inputs

Digital inputs/outputs

Start-up time

Power consumption

Current consumption

Temperature range

Power supply

Shut-down voltage

Dimensions (LxWxH)

USB 2.0

2 CAN channels (via piggybacks) 2 LIN channels

4 inputs:

- Resolution 10 bit (1% precision)

- Sampling rate 1 kHz

- Voltage range 0 V…16 V

2 inputs/outputs, 0 V…36 V

Typ.150 ms with delivered 2 GB Xmore SD card, time varies with capacity and type of the SD/SDHC card

Typ. 660 mW, max. 1100 mW

Operation: typ. 55 mA at 12 V DC Sleep mode: typ. 160 µA (2x CAN and 2x LIN)

GL1000: -40°C…+85°C depending on SD card GL1010: -20°C…+80°C (because of connector)

USB interface: 0°C…+70°C

5 V…30 V, typ. 12 V

4.5 V

GL1000: approx. 107 mm x 85 mm x 35 mm GL1010: approx. 130 mm x 85 mm x 35 mm

Start-up time

Housing

Battery

Data is recorded after the given start-up time if the GL1000/GL1010 already contains a configuration. Updating the configuration or using a new SD card increases this

Cross reference: The recommended SD/SDHC cards are listed in section 2.2.2

SD/SDHC Memory Card.

Aluminium housing: Alubos 800

Lithium primary cell, BR2032 type

GL1000/GL1010 – Compact Logger User Manual GL1000/GL1010 – Compact Logger

> Mounting brackets (GL1000 only)

Optional

> LOGview for displaying signal and status information

2.6 Included with Delivery

Standard scope of delivery

> GL1000/GL1010 Logger

> Vector Logger Configurator on CD

> Vetor Logging Exporter on CD

> G.i.N. configuration program on CD

> Manuals on CD

> USB cable

> 2 GB SD memory card

> Connection cable (open ends)

2.7 Accessories

Optional

> CANgps/CANgps 5 Hz for recording the vehicle position via GPS

> LINprobe as LIN channel extension

CCP/XCP license for CAN

User Manual GL1000/GL1010 – Compact Logger Installation Configuration Programs

3 Installation Configuration Programs

In this chapter you find the following information:

3.1 Overview page 24

3.2 Installation Vector Logger Configurator page 24 Requirements Setup Overview Quick Start

3.3 Installation G.i.N. Configuration Program page 27 Requirements Setup Overview Quick Start

Installation Configuration Programs User Manual GL1000/GL1010 – Compact Logger

The programs are included with delivery.

used in the G.i.N. configuration program.

configurations in LTL.

> This user manual

Restriction Windows 8.1: AUTOSAR databases are not supported.

start menu (if selected during installation).

3.1 Overview

Overview This instruction describes the installation of the software package for the

GL1000/GL1010 containing:

> Vector Logger Configurator

Graphic user interface for easy configuration

> G.i.N configuration program

User interface to create complex configurations with LTL (Log Task Language)

Vector Logger Configurator

G.i.N. configuration program

The Vector Logger Configurator offers a wide range of features to easily create configurations for the logger. The Vector Logger Configurator also supports the download of the configuration and the upload of logging data including the export to different file formats. Additionally the configuration can be saved as LTL code to be

The G.i.N. configuration program can be used as configuration program for high end configurations. It offers full support of all features available with LTL (Log Task Language). This program can be used to import LTL code from the Vector Logger

Configurator or from existing configurations written in LTL or to write own

3.2 Installation Vector Logger Configurator

Overview This instruction describes the installation of the Vector Logger Configurator 2.1 or

higher for the GL1000/GL1010 containing:

> Vector Logger Configurator

> Online help for the Logger Configurator

> User manual for the Logger Configurator

3.2.1 Requirements

Operating system The following software requirements must be fulfilled to run the Vector Logger

Configurator:

> Windows 7 / Windows 8.1 (32/64 Bit)

> Windows 10 (64 Bit)

3.2.2 Setup

The Vector Logger Configurator is installed as follows.

1. Execute the setup, which is found on the installation CD: .\VLConfig\Setup.exe

2. Please, follow the instructions in the setup program to complete the installation.

3. After successful installation, the Vector Logger Configurator can be found in the

User Manual GL1000/GL1010 – Compact Logger Installation Configuration Programs

> CCP/XCP (optional)

Manager|Device Information in the list view on the left hand side.

be opened via the program group in the start menu.

3.2.3 Overview

About Vector Logger Configurator

Vector Logger Configurator enables the configuration of the loggers and offers a wide

range of settings. You may set baud rates for CAN and LIN, define triggers and filters, set LEDs and manage logging files on the SD card. Furthermore for the CAN bus diagnostics and CCP/XCP can be configured. For CCP/XCP the logger needs an installed license. For Seed & Key CANape is required. Vector Logger Configurator also supports trigger and filter access by symbolic names defined in CAN and LIN databases.

Main features are:

> Customizable filters for CAN and LIN messages

> Customizable triggers

> Support of CAN and LIN databases

> Diagnostic support

> File management

Device Information

The Vector Logger Configurator can read out hardware information from the logger. Connect the GL1000/GL1010 with inserted SD card via USB and select the item File

Cross reference: The Vector Logger Configurator is described in detail in the user

manual of this configuration program. The user manual is available as PDF and can

Installation Configuration Programs User Manual GL1000/GL1010 – Compact Logger

logging data.

download a configuration and upload logging files.

GL1010.

subdirectory>.

3.2.4 Quick Start

Quick start Follow the instructions below to configure the logger, start logging and read out

Caution: A formatted SD card has to be empty before inserting in the logger!

The configured logger will delete all files if a formatted SD card is not empty!

The logger deletes the W indows files and the file system on the SD card on start of logging mode if they exist. The logger uses its own file system that cannot be seen in the Windows Explorer. It is required to use the Vector Logger Configurator to

1. Start the program.

2. Open a new configuration via the menu File|New Project…. Select in the displayed dialog the logger type.

3. Select suitable baud rates for CAN and/or LIN (Hardware|CAN Channels and/or Hardware|LIN Channels), respectively.

4. Select the timeout to sleep mode (Hardware|Settings).

5. Configure the logger for a permanent logging of all data from switching on to switching off of the logger by activating the Use permanent logging option in Logging|Triggers.

6. Insert an empty SD card into the GL1000. The SD card is already included in the

7. Connect the logger to PC via USB cable. If the logger is not automatically detected, press <F5> to refresh the display of connected logger devices.

8. Download the configuration via menu Configuration|Write to Device….

9. Set the real-time clock via menu Device|Set Real-Time Clock… (recommended before first logging).

10. Disconnect the logger from the PC.

11. Connect the logger e.g. to your test system (CAN bus). Switch power on via connecting cable on DSUB25.

12. Start logging. LED1 flashes permanently (standard setting for new configurations, can be configured).

13. Stop logging by switching off CAN. Wait until the logger goes to sleep mode (CAN transceiver with wake-up capability necessary) i.e. LED1 must be off.

14. Connect the logger to PC via USB cable.

15. Open the File Manager node in the tree view.

16. Click on Logger Device. Now the logging files are displayed.

17. Select in the General Settings the destination folder and the format for the converted files.

18. Select in the Advanced Settings the options for conversion.

19. Click on the [Convert] button to start the readout and conversion of all data. The files will be located in <Destination folder>/<Destination

User Manual GL1000/GL1010 – Compact Logger Installation Configuration Programs

> G.i.N. user manuals for the configuration program and the hardware

Windows 7, Windows 8.1 and Windows 10

the start menu.

3.3 Installation G.i.N. Configuration Program

Overview This instruction describes the installation of the G.i.N. Configuration Program for the

GL1000/GL1010 containing:

> G.i.N. configuration program

3.3.1 Requirements

Operating system The following software requirements must be fulfilled to run the G.i.N. configuration

program:

3.3.2 Setup

Follow the instructions below to install the G.i.N. configuration program:

1. Execute the setup, which is found on the installation CD: .\GiNconf\setup.exe

2. Please, follow the instructions found there to complete the installation.

3. After successfully installation, the G.i.N. configuration program can be found in

Installation Configuration Programs User Manual GL1000/GL1010 – Compact Logger

> CCP/XCP (optional)

after installation of the program and can be called by the Help menu.

3.3.3 Overview

About G.i.N. configuration program

The G.i.N. configuration program enables the configuration of the loggers and offers a wide range of settings via LTL (Log Task Language). You may set baud rates for CAN and LIN, define triggers and filters, set LEDs and manage logging files on the SD card. CCP/XCP can also be configured with the means of CANape, if the license is installed. G.i.N. configuration program also supports trigger and filter access by symbolic names defined in CANdb databases.

Main features are:

> Customizable filters for CAN and LIN messages

> Customizable complex triggers

> Support of databases

> File management

Cross reference: The G.i.N. configuration program is described in detail in the LTL

user manual of the configuration program. The LTL user manual is available as PDF

User Manual GL1000/GL1010 – Compact Logger Installation Configuration Programs

logging data.

Vector Logger Configurator to download a configuration and upload logging files.

13. Connect logger to PC via USB cable.

selected file format.

3.3.4 Quick Start

Quick start Follow the instructions below to configure the logger, start logging and readout

Warning: A formatted SD card has to be empty before inserting in the logger!

The configured logger will delete all files if a formatted SD card is not empty!

1. Start the program.

2. Create a new project (File|New Project). Select the project path and the device GL1000.

3. Create a new source file (File|New File) and set the baud rate for CAN and the timeout for sleep mode, e.g.

SYSTEM

Can1Timing = Timing500K

Can2Timing = Timing500K

SleepSeconds = 5

END

4. Save the file (File|Save File as) as LTL file in your project directory.

5. Compile this file via Project|Compile or press [F9]. A COD file is created.

6. Insert an empty SD card in the logger. The SD card is already included in the

GL1010.

7. Connect the logger to PC via USB cable.

8. Download the COD file with [F10] or via Project|Compile and Download.

9. Disconnect the logger from PC.

10. Connect the logger e.g. to your test system (CAN bus). Switch power on via connecting cable on DSUB25.

11. Start logging.

12. Stop logging by switching off CAN. Wait until the logger goes to sleep mode (CAN transceiver with wake-up capability necessary).

14. Start the control program with [F11] or via Project|Run Control Program. Select Read out and Export after readout for the CAN logfile and click on [OK].

15. Select the destination directory for the logging files. The upload is started afterwards.

16. The log files are uploaded in a raw format and displayed in the tree view under Logfiles GIN-Logger.

17. After readout the Export dialog is automatically displayed. Select the file format and export parameters and click on [OK]. The raw log file is now converted to the

User Manual GL1000/GL1010 – Compact Logger Index

4 Index

Analog inputs ...................................................... 13

Battery................................................................. 14

Beep.................................................................... 15

CAN .................................................................... 19

CCP/XCP ............................................................ 16

Configuration mode ............................................ 18

Connection cable ................................................ 10

Connectors ........................................................... 9

Delivery ............................................................... 22

Device information .............................................. 25

Diagnostics ......................................................... 17

Digital input/output .............................................. 13

DSUB25 ................................................................ 9

Features ................................................................ 9

Memory cards .................................................... 10

Operating modes ............................................... 18

Piggybacks ......................................................... 19

Pin assignment .................................................... 9

Quick start .................................................... 26, 29

Real-time clock .................................................. 14

Requirements ............................................... 24, 27

SD/SDHC ........................................................... 10

Serial interface ................................................... 14

Serial number ..................................................... 11

Sleep .................................................................. 16

Start-up time ...................................................... 21

Support ................................................................ 5

GiN Configuration Program ................................ 27

Layout GL1000/GL1010 ..................................... 20

Technical data .................................................... 21

Transceiver ........................................................ 19

LED ..................................................................... 12

LIN ...................................................................... 19

Logging mode ..................................................... 18

LOGview ............................................................. 17

Vector Logger Configurator ............................... 24

Wake-up ............................................................. 16

More Information

> News

> Products

> Demo Software

> Support

> Training Classes

> Addresses

www.vector.com

Vector GL1000, GL1010, GL1000 Series User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

1 Introduction

1.1 About this User Manual

1.1.1 Certification

1.1.2 Warranty

1.1.3 Support

1.1.4 Trademarks

2 GL1000/GL1010 – Compact Logger

2.1 General Information

2.2 Features

2.2.1 Connectors

2.2.2 SD/SDHC Memory Card

2.2.3 Serial Number

2.2.4 LED Display

2.2.5 Digital Input/Output

2.2.6 Analog Inputs

2.2.7 Serial Interface

2.2.8 Real-Time Clock with Battery

2.2.9 Beep

2.2.10 Wake-up / Sleep

2.2.11 CCP/XCP

2.2.12 Diagnostics

2.2.13 LOGview Control

2.3 Operating Modes

2.4 Piggybacks

2.5 Technical Data

2.6 Included with Delivery

2.7 Accessories

3 Installation Configuration Programs

3.1 Overview

3.2 Installation Vector Logger Configurator

3.2.1 Requirements

3.2.2 Setup

3.2.3 Overview

3.2.4 Quick Start

3.3 Installation G.i.N. Configuration Program

3.3.1 Requirements

3.3.2 Setup

3.3.3 Overview

3.3.4 Quick Start

4 Index