Vector 4003, 4007, 4010, 4009, 4014 Installation, Operation And Maintenance Manual

W0582

Installation, Operation and Maintenance Manual

VEC-991-4000B

Peristaltic Pumps

Vector 4000 Series

Models: 4003, 4004, 4006, 4007, 4009, 4010, & 4014

Model: 4004

1204 Chestnut Avenue, Minneapolis, MN 55403 Tel: (612) 332-5681 Fax: (612) 332-6937 Toll-free fax [US only]: (800) 332-6812 www.vectorpump.com email: sales@wannereng.com

Model: 4010

Vector 4000 Important Precautions

Safety Measures

! CAUTION

Important Precautions

• To avoid personal injury or pump damage, follow all instructions and safety precautions carefully.

• Don’t exceed the manufacturer’s recommended RPM or pressure limits.

• Follow all codes and hydraulic recommendations on installation and operation of the pumping system.

• To prevent vibration, mount thepump andmotor securely to a rigid, level base.

• For safety and easier servicing, provide adequate work space around the pump. Allow space to remove the front co

ver, hose clamps, hose, and drive unit.

W0387

Safety Precautions

General remarks

These safety and installation instructions contain important information and precautionary notes and must be available to those operating the pump. Please read them thoroughly prior to installation, electrical connection and use of the pump. Operating instructions for components of pumps must be followed.

These safety and installation instructions do not cover local regulations. Installers and operators must also observe local regulations during installation and operation.

Each pump must be labeled by the end user to warn of any hazards that the system process may produce; e.g. corrosive chemicals or hot process etc.

All personnel involved in the operation, maintenance, inspection

and installation of the pump must be fully qualied to perform

the work. The personnel’s responsibilities, competence, and

supervision must be clearly dened by the operator. To the extent

that if the personnel in question is not already in possession of the requisite know how, appropriate training and instruction must be provided. In addition, the operator is responsible for ensuring that the contents of the operating instructions are fully understood by all the responsible personnel.

When installing a Vector pump in conjunction with a motor, or motor and frequency controller, the relevant manuals must be referred to for electromagnetic compatibility.

All safety instructions in this manual and all relevant local health and safety regulations must be followed.

Pay attention to the weight of the pump before attempting to lift either manually or when selecting appropriate lift equipment.

1. Mechanical risk:

Ensure that all protections (cover, sight glass, ventilator hood, coupling protection) are in place before operating the pump.

Disconnect the electrical supply before any mechanical work,

except during hose replacement.

Hose replacement must be done with the pump cover closed.

While replacing a hose, wear protective gloves and clothes. Keep hands away from the brackets, suction and discharge

anges.

During pump maintenance, check that lifting points are correctly used.

The frame of the pump must be rmly fastened to the ground.

2. Electrical risk:

Ensure that the electrical installation conforms to the local standards required; especially regarding ground and thermal protection.

3. Operational risk:

Check that the materials to be pumped are compatible with the following:

• Peristaltic pump operation.

• Hose material.

• Lubricant.

• Inserts material.

• Shoe material.

Wanner cannot guaranty the hose lifetime or the material loss due to a hose burst. It is the operator’s responsibility to prevent pumped liquid loss with additional hose rupture detectors and or automatic shut down valves. Check guarantee for further information.

Ensure that the pump is compatible with the process.

Ensure that the pump suction side pressure is correct.

To avoid hose rupture, make sure that:

• The pump casing is not lled with the pumped material.

• That the suction line is not on load. Otherwise the material may empty into the pump casing and leak out of the pump.

• That the discharge line is not under pressure. Otherwise the pumped material may be forced back into the pump casing and leak out of the pump.

A leakage detector as well as automatic shut down valves are recommended in order to prevent hose rupture.

When draining the pump following a hose rupture, make sure the lubricant and pumped material are disposed of properly.

Complete or partial blockage of the positive displacement pump discharge line can lead to a dangerous high pressure condition. Before operating the pump, make sure there is no complete or partial hose blockage.

Before each use, check the direction of rotation of the pump. While placing the pump under vacuum, mount window screw using an airtight glue to avoid air leakage.

2

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

Vector 4000 Contents

1 IMPORTANT PRECAUTIONS 2

1.1 Safety Measures 2

1.2 Contents 3

2 HOW TO USE THIS MAINTENANCE MANUAL

2.1 Use of the Pump 4

2.2 Responsibility 4

2.3 User Training and Instruction 4

2.4 Limited Warranty 4

3 DESCRIPTION 5

3.1 Identication 5

3.2 Description of Pump Operation 5

3.3 Pump Parts 6

3.4 Pump Hose 9

3.5 Pump Gearbox 9

3.6 Electrical Motors 9

3.7 Available Options 9

4 I N STA LL AT ION

4.1 Inspection 10

4.2 Installation Planning 10

4.3 Piping 10

4.4 Lifting the Pump 11

5 PUMP STARTUP 11

5.1 Preparations 11

5.2 Startup 11

6 MAINTENANCE 11

6.1 Emptying and Filling of Lubricant 11

6.2 Hose Cleaning 13

6.3 Hose Replacement 13

6.3.1 Removing of the Hose 13

6.3.2 Cleaning of the Pump Casing 15

6.3.3 Reassembly of the Hose 15

6.4 Replacement of Spare Parts 17

6.5 Shoe Shimming 21

6.6 Additional Information 22

6.7 Periodic Check 23

7 STORAGE 23

7.1 Pump Storage 23

7.2 Hose Storage 23

8 TROUBLESHOOTING 24

9 CHARACTERISTICS AND TECHNICAL SPECIFICATIONS 26

9.1 Dimensions 26

9.2 Parts List 29

9.3 Lubrication Table 35

9.4 Shoe Shimming Table 35

9.5 Generated Noise and Temperature 36

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

3

Vector 4000 Introduction

2. HOW TO USE THIS MAINTENANCE MANUAL

This technical manual covers the Vector 4000 Series pumps. The manual provides instructions on how to install, start, and maintain the pumps. All persons, installers, and users must read the manual in its entirety prior to installation and use.

Your local Wanner distributor is also available for additional information . For a reply, please include the following information:

- Type of pump

- Pump Also visit our website www.vectorpump.com for further information.

2.1 USE OF THE PUMP

The pump was dened for specic application. Any other use

which does not comply with this use invalidates the warranty. Wanner cannot be held responsible for damage or possible injury incurred during the use of the pump. The pump was designed in accordance with applicable norms and directives. Use the pump only for applications represented above. If you want

to change your application, rst contact your Wanner distributor.

2.2 RESPONSIBILITY

Wanner will be under no circumstances responsible for damage or wounds caused by non respect of security directives and maintenance instructions contained in this manual, or by negligence during the installation, use, service or repair of Wanner hose pumps. Moreover, additional directives of security can be necessary according to working conditions or according process. Contact your Wanner distributor if you notice a potential danger during the use of the pump.

2.4 Limited Warranty

Wanner Engineering, Inc. (“Wanner”) extends to the original

purchaser of equipment supplied or manufactured by Wanner and bearing its name, a limited one-year warranty from the date of purchase against defects in material or workmanship, under normal use and service, and provided the equipment is installed, operated and maintained in accordance with instructions supplied by Wanner. Wanner will repair or replace, at its option, defective parts without charge if: (a) you provide written notice of any defect within thirty (30) days from the discovery of the defect; (b) the claim is received by Wanner

before the expiration of the warranty period; and (c) such parts

are returned with transportation charges prepaid to Wanner Engineering, Inc., 1204 Chestnut Avenue, Minneapolis, Minnesota 55403. A return goods authorization must be received prior to the return of the defective part. No allowance will be made for repairs undertaken without WEI’s written consent or approval.

2.3 USER TRAINING AND INSTRUCTION

Every person who installs, uses, or performs any operations or

maintenance on the pump must be qualied. The person must

also read and be familiar with this technical manual.

Any temporary personnel must be supervised by skilled users.

The order of operational steps dened in this manual must be followed. Store this manual next to the pump so that it can be

consulted at any time.

4

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

Vector 4000 Description

3 DESCRIPTION

3.1 Identication

Vector pumps are identied by the nameplate located on

the upper bracket. It includes the type and model number of the pump. This model number indicates information regarding pump materials, type of the hose, characteristics of the

gearbox, and characteristics of the motor. The gearbox as well

as the motor have their own nameplates on which include the reduction ratio, power, and electrical voltage.

3.2 Description of Pump Operation

PHASE 1

The pump hose is compressed successively by two pressing shoes assembled on a rotating wheel. The rst shoe, by pressing the walls of the hose, will create a vacuum and suck the pumped liquid into the hose.

Wanner Engineering, Inc.

PHASE 2

The pumped liquid has now entered the hose. The second shoe will compress the hose and push the liquid towards the pump outlet.

PHASE 3

As soon as, at the discharge side, the shoe is detached from the hose, the other shoe diametrically opposite is already in compression thus avoiding an internal material leakage. The material is then successively sucked and pushed due to the wheel rotation.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

5

Vector 4000 Description

3.3 PUMP PARTS

19

3

21

271 1

18

7

8

9

12

1610

614

VECTOR 4003, 4004

PART NO DESIGNATION 4003, 4004 MATERIAL

1 CASING CAST IRON

2 COVER, TRANSPARENT LEXAN

3 WHEEL CAST IRON

6 SLEEVE EPDM

7 CLAMP ON CASING STAINLESS STEEL

8 CLAMP SLEEVE / HOSE STEEL

9 CLAMP ON HOSE STEEL

10 SEAL COVER NITRILE

12 INSERT STAINLESS STEEL

14 LUBRICANT GLYCERIN BLEND

16 HOSE NR/NBR/EPDM

18 BRACKET ELECTROPLATED STEEL

19 HUB STEEL

21 FRAME ELECTROPLATED STEEL

71 COVER PLATE ELECTROPLATED STEEL

6

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

Vector 4000 Description

3.3 PUMP PARTS

19

20

3

4

5

21

PART NO DESIGNATION

1

CASING

2

COVER

3

WHEEL

4

SHIM

5

SHOE

6

SLEEVE

7

CLAMP ON CASING

8

CLAMP SLEEVE / HOSE

9

CLAMP ON HOSE

10

SEAL COVER

12

INSERT

14

LUBRICANT

15

SIGHTGLASS

16

HOSE

18

BRACKET

19

HUB

21

FRAME

46

SIGHT GLASS SEAL

47

INLET/OUTLET FLANGE

2

10

VECTOR 4006, 4007, 4009, 4010

16

4006, 4007 MATERIAL

CAST IRON

ELECTROPLATED STEEL

CAST IRON

GALVANIZED STEEL

ALUMINIUM

EPDM

STAINLESS STEEL

NITRILE

STAINLESS STEEL

GLYCERIN BLEND

LEXAN

NR/NBR/EPDM

ELECTROPLATED STEEL

STEEL

NITRILE

STAINLESS STEEL

1

14

47

18

6

4009, 4010 MATERIAL

CAST IRON

STEEL

CAST IRON

GALVANIZED STEEL

ALUMINIUM (4009) / CAST IRON (4010)

EPDM

STEELCK

STAINLESS STEEL

STEEL

NITRILE

STAINLESS STEEL

GLYCERIN BLEND

LEXAN

NR/NBR/EPDM

ELECTROPLATED STEEL

STEEL

NITRILE

STAINLESS STEEL

15

7

8

12

9

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

7

Vector 4000 Description

3.3 PUMP PARTS

2

1

18

47

19

20

15

3

4

5

21

7

8

12

9

10 16 14 6

PART NO DESIGNATION

1

CASING

2

COVER

3

WHEEL

4

SHIM

5

SHOE

6

SLEEVE

7

CLAMP ON CASING

8

CLAMP SLEEVE / HOSE

9

CLAMP ON HOSE

10

SEAL COVER

12

INSERT

14

LUBRICANT

15

SIGHT GLASS

16

HOSE

18

BRACKET

19

HUB

20

BOLT ON PLATE

21

FRAME

46

SIGHT GLASS SEAL

47

INLET/OUTLET FLANGE STAINLESS STEEL

VECTOR 4014

4014 MATERIAL

CAST IRON

STEEL

CAST IRON

GALVANIZED STEEL

CAST IRON

EPDM

STAINLESS STEEL

STEEL

NITRILE

STAINLESS STEEL

GLYCERIN BLEND

LEXAN

NR/NBR/EPDM

ELECTROPLATED STEEL

STEEL

CAST IRON

STEEL

NITRILE

8

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

Vector 4000 Description

3.4 PUMP HOSE

Wanner hoses are manufactured according to strict specications for the best performance of the pump and to assure optimum hose life. Hoses are available in four materials: Natural Rubber (NR), perbunan (NBR), EPDM, and Hypalon. The hose material must be compatible with the liquid pumped. Consult your Wanner distributor to obtain the correct hose for your use.

Vector 4000 pumps operate in temperatures between + 14°F and +176°F. Pumps are painted with a 150µ Polyurethane paint to resist corrosive environments. Pumps are designed for indoor and outdoor use.

HOSE DIMENSIONS (dimensions in mm)

PUMP INNER ø THICKNESS LENGTH

4003 10 11 570 4004 15 11 830 4006 25 14.5 1090 4007 32 15.5 1300 4009 40 13.5 1500 4010 51 15 1820 4014 80 21.5 2910

3.5 GEARBOX

Gearboxes are sized according to the pump’s radial loads. Consult the gearbox maintenance manual for the type, quan-

tity, and frequency of oil changes.

3.6 ELECTRICAL MOTORS

The standard motors provided on pumps are TEFC motors and require a 230/460 VAC, 60Hz, 3Ø voltage source. If the pump

is to be used in an explosive environment, please contact the

factor y.

3.7 AVAILABLE OPTIONS

The following Vector Pump options are available:

- Hose rupture detector.

- Pulsation dampener. Please contact your Wanner distributor for additional information about these options

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

9

Vector 4000 Installation

W0383A

6 to 8 feet

4 INSTALLATION

4.1 INSPE C T I O N

The pump must be checked upon receipt for any possible damage or incomplete shipment. Notify Wanner Engineering of any discrepancies immediately.

Check all boxes or packages containing spare parts or

accessories packed with the pump.

4.2 INSTALLATION PLANNING

Location

1. Locate the pump near the liquid source, so that the suction line is short and direct.

2. When practical, locate the pump above the level of the liquid; if the hose fails, the pumpage drains back into the tank.

3. Allow space to remove the front cover, hose, and drive unit. See Inlet Hose Length Chart (A).

Inlet Hose Length Chart (A)

A

PUMP DISTANCE (A)

4003 1.3 ft 4004 1.6 ft 4006 2.6 ft 4007 3.3 ft 4009 3.9 ft 4010 4.6 ft 4014 6.5 ft

Foundation

The foundation should be su󰀩ciently rigid and substantial to

absorb any vibration, and to permanently support the base plate at all points. A concrete foundation, poured on a solid footing of adequate thickness to support the pumping unit provides the most satisfactory foundation.

The base plate should be installed in a level position. The size and location of the base mounting holes are shown on the pump

specication sheets. Use the dimensions provided in the pump specication data sheets for general piping.

Note: For a detailed description of proper procedures for grouting base plates, refer to the Hydraulic Institute Standards.

4.3 PIPING

Inlet piping:

1. Size the inlet line 1.5 or two sizes larger than the pump suction opening.

2. Suction lines should be as short and direct as possible.

3. See Site Plumbing Figure below. Install 6 to 8 feet of

reinforced exible hose between pump and rigid piping to absorb vibration, expansion and contraction, and to make

maintenance easier.

Note: The inlet hose must be capable of withstanding a

vacuum. This avoids hose collapse which will restrict

ow.

4. Install an inlet pressure/vacuum gauge on the inlet side of the pump.

5. To reduce turbulence and resistance, do not use 90° elbows. If turns are necessary in the suction line use 45° elbows or long sweeping elbows when required.

6. Install piping supports where necessary to relieve strain on the inlet line and to minimize vibration.

7. In some cases, a pulsation dampener may be required to decrease acceleration head and pulsations. Mount dampener within ten pipe diameters of the pump suction connection. The closer the better.

Discharge piping:

1. See Site Plumbing Figure below. Install a length, B,

of reinforced flexible hose (one size larger than pump

connection) between pump and rigid piping. This will absorb

vibration, provide for expansion and contraction. It also

creates a reservoir and eases the replacement of the hose.

2. Size the rigid discharge line to be at least the size of the pump inlet connection.

3. Install piping supports where necessary to relieve strain on discharge piping and to minimize vibration.

4. Install a pressure gauge in the discharge piping.

5. In some cases, a pulsation dampener may be required to decrease pulsations. Mount dampener within ten pipe diameters of the pump discharge connection. The closer the better.

6. Install a pressure relief valve to protect the pump and piping.

10

Wanner Engineering, Inc.

Site Plumbing Figure

B

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

PUMP DISTANCE (B)

4003 2 ft 4004 2 ft 4006 2.5 ft 4007 3 ft 4009 4 ft 4010 5 ft 4014 8 ft

Vector 4000 Installation and Maintenance

4.4 LIFTING THE PUMP

Pumps are provided with two lift rings tted on the upper part

of the frame. While lifting the pump, do the following:

1. Lift the complete hose pump using the lifting rings plus

additional support on the gearbox and the motor using

suitably rated straps or slings.

2. Never exceed a lift’s upper weight limit. Refer to the Pump

Weight table below to determine the size of lift required.

3. The motorized pump, given its centre of gravity, will tend to overbalance on the pump head side. Make sure that the persons are at a security distance of the pump to avoid any risk of wound.

4. Never raise the pump otherwise than by the pump’s lifting rings.

5. Never raise the pump by it’s orices nor by it’s brackets.

Pump Weight

Pump 4003 4004 4006 4007 4009 4010 4014

Lb. 55 77 176 287 463 694 2050

5. PUMP STARTUP

5.1 PREPARATIONS

1. Connect the electrical motor in accordance with the local

rules and regulations. Perform this work by qualied

personnel.

2. Make sure that the lubricant level arrives at the level of the sight glass. Add lubricant if required by the breather or by the sight glass. See 6.1.

3. Make sure the shimming of the pump is according to the pump process. See 6.5.

4. Check the direction of rotation of the pump. It is recommended to install a rotation inverter on the motor for the hose change.

5. 2 STARTU P

1. Install piping at the inlet and outlet of the pump.

2. Make sure that valves at the inlet and outlet are opened.

3. Start the pump by checking its direction of rotation by the sight glass.

6. MAINTENANCE

Note: The numbers in parentheses are Reference Numbers located in the Parts List exploded views of this manual.

6.1 CHANGING LUBRICANT.

Check lubricant level every 1000 hours. Change as follows:

1. Stop the pump

2. Place a tray underneath the drain plug (23)

3. If necessary, install a tap and a drain circuit instead of the drain plug

4. Make sure tray will hold the quantity of lubricant during the drainage process. See 9.3 Lubrication Table for quantity.

5. Unscrew the drain plug and drain lubricant

6. Position and tighten drain plug by applying Teon® band

or waterproof paste of close drain tap.

7. Remove sight glass (15) as well as seal (46) and ll the casing with Wanner lubricant. See 9.3 Lubrication Table for quantity. Fill with lubricant to the level of the sight glass or underneath the shaft line. See illustration below.

Note: You can also ll the casing by removing the breather cap (52) at the back of the pump casing.

8. Check the condition of the seal (replace if necessary). Reassemble sight glass (or tighten the breather cap).

Maximum lubricant

level

15,46

52

Note: The numbers in parentheses are Reference Numbers located in the Parts List exploded views of this manual.

Wanner Engineering, Inc.

23

Note: If the pump is mounted with the inlet/outlet posi- tioned upwards, lubricant drainage is obtained by unscrewing some cover bolts in the lower part.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

11

Vector 4000 Maintenance

W0582

6.1 CHANGING LUBRICANT. (Cont’d)

FOR MODELS 4003, 4004: Unscrew breather plug (52). Place a funnel inside the

breather plug hole and ll the casing with the Wanner lubricant.

See 9.3 Lubrication Table for quantity. Fill lubricant to just underneath the shaft.

52

12

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

Vector 4000 Maintenance

6.2 HOSE CLEANING

The hose can be cleaned without removing. Use water or cleaning liquid (check compatibility with hose material). With Some pumped material requires cleaning after each use to avoid material hardening in the hose.

CAUTION: Make sure that the cleaning liquid temperature is the same as the hose material.

6.3 HOSE REPLACEMENT

Note: The numbers in parentheses are Reference Numbers located in the Parts List exploded views of this manual.

CAUTION: Before any hose change, check the following points:

1. Skilled personnel are to perform this service and have read and understand this manual.

2. Close inlet and outlet valves to minimize material loss.

3. Wear clothes that provide protection when using the pumped material.

4. Observe all safety and environmental rules governing the use of the pumped material.

6.3.1 HOSE REMOVAL

1. Disconnect and remove suction and discharge piping.

2. Drain lubricant as outlined in Section 6.1.

3. Loosen clamps (8) and (9) at the suction inlet.

Remove insert (12) and ange (47) See Figure 1.

8

9

47

12

Figure 1

FOR MODELS 4003, 4004:

3. Loosen clamps (8) and (9) at suction inlet. Remove circlips (24) and remove bracket (18) and insert (12). See Figure 2.

8 9

24

12

18

Figure 2

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

13

Vector 4000 Maintenance

6.3.1 HOSE REMOVAL (Cont’d)

4. -At the discharge outlet, loosen clamps (8) and (9).

-Remove the insert (12) and remove the ange (47) as

well as the brackets (18). See Figure 3.

5. Remove clamps.

9 8

47

FOR MODELS 4003, 4004: At the pump outlet, loosen clamps (8) and (9).Remove circlips (24) and dismantle bracket (18). Remove insert (12) and clamps. See Figure 5.

8

9

12

18

WARNING! The hose can come out of the pump casing very fast and cause harm. Ensure that no one is in front of the pump´s outlets when removing the hose.

WARNING! Use care when you jog/run the motor to avoid injury.

6. Carefully jog/run motor to expel hose from pump casing

outlet side. See Figure 4.

12

Figure 3

Pump casing

24

18

Figure 5

Figure 4

14

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

Vector 4000 Maintenance

6.3.2 PUMP CASING CLEANING

Note: The numbers in parentheses are Reference Numbers located in the Parts List exploded views of this manual.

This operation is necessary when a hose burst has caused material contamination inside the pump casing.

1. Unscrew cover bolt s (33) by leaving two cover bo lt s partly fastened to the casing. Partially remove the cover (2) from

the casing and x a shackle in one of the cover’s highest bolt

holes (4014 is equipped with a lifting ring). Unfasten the remaining cover bolts and remove the cover. See Figure 6.

2. Check the state of the cover seal (10) and replace if necessary.

3. Check the state of wear of the pressing shoes (5) and replace them if necessary. See 6.4.

CAUTION: A wear of shoes can cause problems to the pump and provoke abnormal hose lifetime.

4. In the case of a hose burst, it is possible that the shaft seal (26) and seal ring (27) have been damaged when pumping an abrasive liquid. See 6.4 and Parts List to replace.

5. Wash the casing with clear water and remove any residue.

6. Dry the pump casing entirely.

7. Replace the cover seal in its groove.

8. Reassemble the pump cover.

6.3.3 REASSEMBLY OF THE HOSE

2,10

6

33

Figure 6

5

47

WARNING! You should never assemble a new hose without a mounted cover.

1. Pre-assemble the ange (47) at the inlet port with two

bracket bolts See Figure 7.

FOR MODELS 4003, 4004: Temporarily mount the bracket 18 at the inlet port.

2. Clean the new Wanner hose carefully. Slightly coat it with Wanner lubricant. Slightly lubricate the inside of the sleeve (6).

18

Figure 7

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

15

Vector 4000 Maintenance

6.3.3 REASSEMBLY OF THE HOSE (Cont’d)

3. Insert hose at the outlet port. See Figure 8.

WARNING! Use care when you jog/run the motor to avoid injury.

4. Reverse the direction of rotation of the motor.

5. While pushing on the hose, jog/run the motor and check the direction of rotation.

6. The shoes mounted on the wheel are going to “swallow” the hose and push it out of the inlet port. Jog the motor to bring

the hose against the ange (47). See Figure 9.

7. Assemble the clamps (8) and (9) on the inlet side. Mount the insert (12) into the hose. Tighten clamps.

FOR MODELS 4003, 4004 Dismantle the bracket 18. Mount clamps on the hose. Mount the insert into the hose. Fix bracket (18) and block the insert with circlips (24). Tighten clamps.

Outlet Port

Figure 8

Note: If you have di󰀩culty assembling inserts into the

pump hose, coat them slightly with Wanner lubricant. Never use another lubricant.

8. Assemble the brackets (18) and pre-assemble ange (47) on

the outlet side with two temporary bolts.

FOR MODELS 4003, 4004 Assemble the brackets at the outlet side.

9. Reverse the direction of rotation of the motor.

WARNING! Use care when you jog/run the motor to avoid injury.

10. Jog/run the motor to bring the hose against the discharge

ange.

11. Perform step 7 at discharge side.

12. Fill the pump with the necessary quantity of Wanner lubricant. See 6.1. and 9.3.

13. Take away the temporary ange bolts and x the piping on

both suction and discharge sides.

14. Open the valves at the suction and discharge sides.

15. Check the direction of rotation of the pump. Check for any possible lubricant leakage by the inserts, sleeves or cover.

18

47

Figure 9

16

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

Vector 4000 Maintenance

6.4 REPLACEMENT OF SPARE PARTS

Note: The numbers in parentheses are Reference Numbers located in the Parts List exploded views of this manual.

6.4.1 REPLACEMENT OF PUMP SHOES (except 4003 and

4004)

WARNING! Use care when you jog/run the motor to avoid injury.

1. Jog/run the motor and position one of the shoes in front of the sight glass.

2. Cut the power supply.

3. Drain the lubricant. See 6.1.

4. Remove the pump cover (2) as well as the cover seal (10). See Figure 10 and Figure 11.

5. Disassemble the shoe which is not in contact with the hose and put aside the shims if any. Check that the pin (30) is still on the wheel (4006, 4007, 4009, 4010).

6. Mount a new shoe on the wheel with shoe bolt (28) and shoe bolt washer (29). Slide the shims (4) between the shoe and the wheel before tightening.

CAUTION: Be careful of the position of the shoe with centering pin 30 (4006, 4007, 4009, 4010).

7. Tighten the shoe onto the wheel.

8. Temporarily reassemble the cover with three cover bolts (33) positioned 120° from each other.

WARNING! Use care when you jog/run the motor to avoid injury.

9. Jog the motor 180° to bring the second shoe in front of the sight glass.

10. Remove the cover once again and perform steps 5 thru 7.

11. Reposition the cover and tighten all cover bolts.

2,10

Figure 10

28,29

Wanner Engineering, Inc.

Figure 11

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

17

Vector 4000 Maintenance

6.4.2 REPLACEMENT OF THE SEAL RING (27) AND THE SHAFT SEAL (26)

Note: The numbers in parentheses are Reference Numbers located in the Parts List exploded views of this manual.

Wanner hose pumps are equipped with a leakage channel to observe wear of the seal ring or the shaft seal. This channel is

at the back of the pump casing underneath the gearbox ange. It also protects the gearbox seals by leaving the lubricant or

the material to pass freely at the back of the pump casing. See Figure 12, Figure 13, and Figure 14.

41

72

27

LEAKAGE CHANNEL

Figure 12

PUMPS 4006, 4007, 4009, 4010

1. Isolate the pump from the power supply.

2. Empty the lubricant and clean out the pump. See 6.1.

3. Remove the pump hose. See 6.3.1.

4. Disassemble the pump cover and remove the cover seal (10).

5. Disassemble the wheel by unscrewing the hub (19).

6. Remove the wheel of the pump shaft with a suitable lifting equipment.

7. Support the gear motor with a suitable lifting equipment.

8. Unscrew nuts (41), washers (72) and remove gearbox from

pump casing.

9. Cut out and remove seal sleeve (27) if damaged.

10. Slip on spacer ring (73) if used and glue to the shaft. Note: Contact Factory before performing step 11!

11. Position new seal ring (27) against spacer ring or the gearbox shaft’s shoulder. Fill the key groove with silicone mastic to ensure correct sealing.

12. Remove the shaft seal (26) with a drift punch.

13. Replace with new shaft seal using a suitable tool (wooden or plastic cylinder). Check the mounting position of the seal (opened side turned to the cover).

26

Cylinder Tool

Figure 13

18

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

Vector 4000 Maintenance

14. Mount the gear motor on the casing being careful not to damage the shaft seal. Tighten nuts (41) and washers (72).

15. Mount the wheel on the pump shaft. Position and space wheel as indicated by the illustration in Figure 15. Refer to the Positioning Distances (L) table, depending on the pump used.

19

LL

Figure 15

Figure 14

Model: 4003 4004 4006 4007 4009 4010 4014

Distance: 4 2.75 5.5 6 5 3 8

Distance (L) in mm (plus or minus 0.5 mm)

Positioning Distances (L)

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

19

Vector 4000 Maintenance

16. Cross tighten the expandible hub (19) with a dynamometric spanner to the torque gure specied in the Hub Torque

table. Check the wheel position once again. See Figure 16.

Hub Torque TABLE

Torq u e Spanner

Figure 16

17. Mount the cover seal (10) in its groove and mount the cover.

18. Mount the pump hose as stated in 6.3.3.

Note: The numbers in parentheses are Reference Numbers located in the Parts List exploded views of this manual.

1. Steps 1 thru 10. for Vector pumps 4003 and 4010.

2. Disassemble the seal ange (25) and remove the shaft

seal with a screwdriver or a similar tool.

3. Take the new shaft seal (26) between the thumb and index ngers and form a “gure 8”.Insert seal into its groove. See

Figure 17.

25

PUMP TYPE TORQUE Nm

4003, 4004 12 4006, 4007 13 4009 27 4010 35 4014 11 0

67

26

Figure 17

4. Mount gear motor on pump casing. See 6.4.2., step 13.

5. Replace the O-ring (67) if necessary and reassemble the

seal ange.

6. For pump 4014, perform steps 14 thru 17 as above.

20

Wanner Engineering, Inc.

“gure 8”

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

Vector 4000 Maintenance

6.5 SHOE SHIMMING (except 4003 and 4004)

Note: The numbers in parentheses are Reference Numbers located in the Parts List exploded views of this manual.

Note: This paragraph does not apply to pumps 4003, 4004.

CAUTION: The shimming of shoes is an operation which consists in adding shims under the shoe to stop any internal leakage. An internal leakage considerably reduces

the life time of the hose as well as the ow. As a result,

it is essential to adjust the shoe’s shimming according to the rotation speed of the pump, the desired discharge pressure and the liquid viscosity.

WARNING! Never run the pump without the sight glass.

The shoe shimming can be made without disassembling the hose or the cover. Shims are inserted or removed thru the sight glass opening as described in the following steps. See Figure 18 illustrations.

WARNING! Use care when you jog/run the motor to avoid injury.

37

1. Jog/run the motor and bring a shoe in front of the sight glass.

2. Cut the power supply of the pump.

3. Unscrew the sight glass bolts (37) and remove taking care in not damaging the seal.

4. Slightly unscrew the shoe’s fastening bolt(s) and lift the shoe (5)

o󰀨 the wheel with a screwdriver or a similar tool.

5. You can now either slide in or remove the necessary number of shims under the shoe.

Note: Consult the shimming table 9.6 to determine the precise number of shims according to your application.

6. Tighten the shoe bolts (28).

7. Reassemble the sight glass with its seal.

8. Re-connect and jog/run the motor to bring the second shoe

WARNING! Use care when you jog/run the motor to avoid injury.

in front of the sight glass.

9. Cut the power supply of the pump.

10. Repeat steps 3 thru 7. Replace the sight glass seal (46) if necessary.

5

Inserting Shims

Wanner Engineering, Inc.

Figure 18

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

21

Vector 4000 Maintenance

6.6 ADDITIONAL INFORMATION

Note: The numbers in parentheses are Reference Numbers located in the Parts List exploded views of this manual.

6.6.1 MAINTENANCE AND PERIODIC INSPECTIONS TABLE (4003, 4004, 4006, 4007, 4010, and 4014).

1 Pump hose replacement In prevention, change the pump hose

after 90 % of the life time of the rst

hose.

2 Lubricant replacement. At the end of two hose changes or 5000

hours of use. Otherwise, in every hose break

3 Gearbox oil replacement. Refer to the gearbox maintenance

manual provided with the pump.

4 Replacement of the seal ring (27). In case of presence of lubricant in the

leak channel.

5 Replacement of the shaft seal (26). In case of presence of lubricant in the

leak channel.

6 Replacement of the shaft seal (105)

and (10 6)

7 Replacement of the shoes. If these are worn on the contact

8 Replacement of the cover seal (10). In the case of a leak around the pump

8 Replacement of the sleeves (6). If damaged. Refer to 6.3. Perform steps

9 Replacement of the bearings (103)

and (104)

In case of presence of oil in the leak channel or at the lip seals.

surface.

cover.

If there are abnormal noises coming from the bearing case.

See 6.3.

See 6.1. and 9.3.

See 6.4.2.

See 6.4.2. and 6.6.

See 6.4.1.

See 6.3.2.

1 thru 4 of 6.3.1 and change sleeves. Use care.

See 6.4. and 6.6.

9 Check the lubricant level. Before starting the pump and

periodically during the pump service.

10 Check for lubricant leakage at the

leakage channel.

11 Check the pump casing to dis-

cern possible leakages around the

cover, the sight glass, the anges and

the sleeves.

12 Check for wear on the shoe’s pressing

surface.

13 Check the presence of a gearbox oil

leakage.

14 Check for strange noises coming

from the pump, gearbox and bearing case or abnormal pump casing temperature.

22

Wanner Engineering, Inc.

Before starting the pump and periodically during the pump service.

At every hose change. See 6.4.

Before starting the pump and periodically during the pump service.

Periodically during the pump service.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

See 6.1.

See 6.4.

See 3.5.

Vector 4000 Maintenance and Storage

6.6.2 SETUP

Note: The numbers in parentheses are Reference Numbers located in the Parts List exploded views of this manual.

Before the setting up the pump, check the following:

1. The pump with its drive and frame must be xed to a solid base with a slope which does not exceed 5mm for 1m and must be rmly fastened to this one.

2. The alignment of pump and drive shafts must be made in accordance with instructions given by the manufacturer of

the coupling. Refer to the specic notice of such material.

To achieve alignment and coupling, use a perfectly straight ruler to control the misalignment, and a feeler gauge for angular misalignment. Control four points (top, bottom, left, right) at each stage of the installation (after setting on

foundations, after xing pipes and after a rst start).

3. Make sure there is enough room around the pump to carry out maintenance. If that was not the case, envisage the moving of the pump in a space provided for this purpose.

4. Make sure the room is adequately ventilated to relieve the heat generated by the pump. Leave a space behind the motor ventilator hood so as not to obstruct the air intake.

6.6.3 PUMP STARTING

Perform the procedures outlined in the PUMP STARTUP section 5, before pump operation.

6.7 PERIODIC CHECK

Regularly check the absence of grease coming from the leakage channel or from lip seal (106).

7 STORAGE

7.1 PUMP STORAGE

Store the pump in a sheltered and dry place and ensure that the storage room temperature is between 68°F and 113°F.

Protect the pump if necessary and block the inlet and outlet

orices:

1. If the pump stays without working more than 1 month, with draw the hose from the pump or remove one of the shoes as well as its centering pin and position the wheel so that the second shoe can be seen threw the sight glass.

For models 4003,4004, position the wheel so that one of the

cam lobes remains submerged in the lubricant.

2. If you can neither remove the hose or one of the shoes, run the pump 5 minutes a week.

7.2 HOSE STORAGE

Hoses must be stored sheltered from light in a cool place.

CAUTION: Hose performance is reduced after two years, due to material aging.

6.6.4 BEARING CASE DISMANTLING AND LIP SEAL REPLACEMENT

Perform steps in 6.4.2. Disassemble the bearing case in the

same way as for the gearbox.

1. Remove lip seals (105) and (106) from the bearing case.

2. Remove circlips (107).

3. Remove shaft with bearings.

4. Disassemble bearings and replace them together with shaft (102) as needed.

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

23

Vector 4000 Troubleshooting

8 TROUBLESHOOTING

PROBLEM POSSIBLE REASON RESOLUTION

The pump does not work No power supply. Check that the pump power switch is in

the “ON” position.

Check the motor connection.

The pump wheel stalls. Check the hose.

Check that the discharge pressure is not too high.

Check that the material hasn’t blocked the hose.

The lubricant level detector has been activated.

Low capacity or pressure Not enough Shims under shoes. Add the su󰀩cient number of shims.

Air leak at the inlet of the pump. Check and tighten pump clamps (if nec-

Valve closed or partly closed at inlet. Open valve.

Wor n hose. Replace hose.

Material too viscous or excessive pump

speed in comparison with the material viscosity.

Piping blocked or partly blocked at inlet. Unblock piping and ensure good material

Check lubricant level. Check if the pump hose has burst. Replace.

essary).Check inlet piping seals.

Check with your Wanner distributor.

ow.

24

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

Vector 4000 Troubleshooting

8 TROUBLESHOOTING

PROBLEM POSSIBLE REASON CORRECTION

Hose life is too short. Incompatibility of the hose with the

pumped material.

Discharge pressure too high. Check that the discharge pressure of the

Pump speed too high. Reduce pump speed.

Wrong shimming. Check shimming.

Pumped material temperature too high. Contact your Wanner distributor.

Lubricant leakage around the cover Loose cover bolts. Cover seal wear. Tighten cover bolts. Replace cover seal.

Lubricant leakage in the leakage channel

(underneath the gearbox ange)

Lubricant leakage at the sleeves Loose clamps or damaged sleeve(s). Tighten clamps. Replace sleeves.

Pipe pulsations. Piping not connected correctly. Fix piping connections.

Shaft seal or seal ring wear. Replace.

Process creating abnormal pulsations due to the pumped material, the speed of pump, discharge pressure, or the pipe sizing.

Make sure the compatibility of the hose with your material and contact your Wanner distributor.

pump does not exceed 15 bars (or 8 bars

for 4003, 4004). Check that the outlet piping is not blocked up and that all valves are opened.

Make sure that the security valve works co rrec tly.

Make sure that the piping friction losses

do not exceed the value requested for an

appropriate functioning of the pump.

Contact your Wanner distributor.

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

25

Vector 4000 Dimensions

9 CHARACTERISTICS AND TECHNICAL SPECIFICATIONS

9.1 VECTOR 4000 PUMP DIMENSIONS: 4003, 4004, 4006, 4007, 4010, 4014 FLANGED GEAR MOTOR and FPSHS series PUMPS 4003, 4004

M

O

L

N

4 x K

P

I

J

3 LOBES

2 LOBES

H

D

Q

F

G

C

E

B

A

Model A B C D E F G H I J

4003 103.5 115 226 95 256 220 240 33.5 260 280

4004 73 193 296 145 322 250 280 51.75 300 330

Model K L M N O P Q

4003 4xø9 - 46.5 34.5 ø16 * 56 81.25

4004 4xø13 - 49 35.5 ø20 * 68.8 124.75

Note: all units in mm.

ALL DIMENSIONS AND TECHNICAL DATA IS SUBJECT TO CHANGE WITHOUT NOTICE

26

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

Vector 4000 Dimensions

B C D E F G H I J

L M N

Q

65 69

83 89

9.1 VECTOR 4000 PUMP DIMENSIONS: 4006, 4007

L D C

M N

O

H

E

H

B

4 x K

P

I F

J

G

Q Q

A

Model

4006

4007

Model

4006

4007

Note: all units in mm.

A

95

122.5

K

4xø13

262

330

-

355.5

435.5

190

238

416

525.5

O

(ANSI FLANGE)

1in. 150 lb

1.5 in. 150 lb

311

426

61

109

351

476

P

110

157.75

110

157.75

560

770

600

810

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

27

Vector 4000 Dimensions

N

Q

86

B C D E F G H I J

9.1 VECTOR 4000 PUMP DIMENSIONS: 4009, 4010, 4014

L

N

O

M

4xK

P

I

J

D C

Q Q

H

E

H

F

G

B

A

MODEL

4009

4010

4014

MODEL

4009

4010

4014

Note: all units in mm.

A

110

164.5

262

K

4xø19

4xø27

430

554

876

M

75

94.5

140.5

400

517.5

803

102

142

28

Wanner Engineering, Inc.

291

360

555

O

(ANSI FLANGE)

1.5 in. 150 lb

2.0 in. 150 lb

3.0 in. 150 lb

616

801.5

1320

340

513

690

P

87

152

210

170

256.5

345

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

420

593

830

170

186.5

345

850

950

1300 1400

1050

950

Vector 4000 Parts

51 6

41

27

39

7 848 9

16

26 23 52 18 42 21

3

121

42 72

19

10

2

34

33

71 not shown. See 3.3. Vector 4003, 4004 Description.

Vector 4003, 4004

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

29

Vector 4000 Parts

768125 151237

8 9 48

27

22

40

3

74

24 27 14 139 26

A

12

23

47

16

10

2

46

15

38

37

35 3633

B

DETAIL B

19

30

28

29

5

DETAIL A

4

Vector 4006, 4007

30

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

Vector 4000 Parts

768125 151237

8 9 48

27

22

40

3

74

24 27 14 139 26

A

12

23

47

16

10

2

46

15

38

37

35 3633

B

DETAIL B

19

30

28

29

5

DETAIL A

4

Vector 4009, 4010

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

31

Vector 4000 Parts

63 78 64

Lifting ring on

4014 cover.

32

37 72

37

22

31

19

48

42 72

26 25 43

70*

67

6 7 8 9

B

14136 21

A

12 10 2 46 51 83 7316

47

2315 25 18

3435 36 33

C

DETAIL C

20

3

30**

DETAIL A

28

29

4

5

DETAIL B

Vector 4014

32

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

Vector 4000 Parts List

X X X

X

X X X

X X

X X X

X

X X X

X

X X X

X

X X X

X

X X X

X X

X

9.2 VECTOR 4000 Parts List

F.

Ref # DESCRIPTION 4003 4004 4014

1

CASING

2

COVER, TRANSPARENT

3

WHEEL

4

SHIM

5

SHOE

6

SLEEVE

7

CLAMP SLEEVE

8

CLAMP ON SLEEVE / HOSE

9

CLAMP ON HOSE

10

COVER SEAL

12

INSERT

14

LUBRICANT

15

SIGHT GLASS

16

HOSE

18

BRACKET

19

HUB

20

BOLT ON PLATE

21

FRAME

22

LIFT RING

23

OIL PLUG

24

CIRCLIPS

25

SEAL FLANGE

26

SHAFT SEAL

27

SEAL SLEEVE

28

SHOE BOLT

29

SHOE BOLT WASHER

30

SHOE CENTERING PIN

31

BOLT ON PLATE SCREW

32

NUT FOR 31

33

COVER BOLT

34

COVER BOLT WASHER

35

COVER STUD

36

NUT FOR 35

37

SIGHT GLASS BOLT

38

WASHER FOR 37

39

FRAME BOLT

40

WASHER FOR 39

41

GEARBOX STUD

42

NUT FOR 41

43

SEAL FLANGE BOLT

46

SIGHT GLASS SEAL

47

INLET & OULET FLANGE

DESIGNATION

FPSH 05

FPSH10

X

FPSH15 FPSH20

X

4006 to

FPSH25 TO

4007

FPSH40

X

4009 to

FPSHX40 TO

4010

X

FPSH80

X

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

33

9

CLAMP ON HOSE

X X X X

10

COVER SEAL

X

X X X

12

INSERT

X

X X X

14

LUBRICANT

X

X X X

15

SIGHT GLASS

X

16

HOSE

X

X X X

18

BRACKET

X

X X X

19

HUB

X

X X X

20

BOLT ON PLATE

21

FRAME

X

X X X

22

LIFT RING

23

OIL PLUG

X

X X X

24

CIRCLIPS

X

25

SEAL FLANGE

26

SHAFT SEAL

X

X X X

27

SEAL SLEEVE

X

X X X

28

SHOE BOLT

X

29

SHOE BOLT WASHER

X

30

SHOE CENTERING PIN

X

31

BOLT ON PLATE SCREW

32

NUT FOR 31

33

COVER BOLT

X

X X X

34

COVER BOLT WASHER

X

35

COVER STUD

X

36

NUT FOR 35

X

37

SIGHT GLASS BOLT

X X

38

WASHER FOR 37

X

39

FRAME BOLT

X

X X X

40

WASHER FOR 39

X

X X X

41

GEARBOX STUD

X

X X X

42

NUT FOR 41

X

X X

43

SEAL FLANGE BOLT

46

SIGHT GLASS SEAL

X

47

INLET & OULET FLANGE

X

X X X

X X

X X X

X

X X X

X X

X X X

X

Vector 4000 Parts List (Cont’d)

9.2 VECTOR 4000 Parts List (Cont’d)

F.

Ref # DESCRIPTION 4003 4004 4014

48 BRACKET BOLT

49 BRACKET BOLT WASHER

51 90° BEND

52 BREATHER PLUG

63

101 BEARING CASE

102 SHAFT

103 ROLLAR BEARING

104 BALL BEARING

105 LIP SEAL

106 LIP SEAL

107 CIRCLIPS

108 GREASER

109 SHAFT KEY

LIFT RING ON COVER

64

BOLT FOR 63

67

O RING FOR SEAL FLANGE

70

GEARBOX CENTRING FLANGE

71

COVER PLATE

72

WASHER for 41

73

SPACER RING

74

PLUG

110 SHAFT KEY

DESIGNATION

FPSH 05

FPSH10

X

FPSH15 FPSH20

X

4006 to

FPSH25 TO

FPSH40

4007

X X

4009 to

FPSHX40 TO

4010

FPSH80

X

34

Wanner Engineering, Inc.

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

Vector 4000 Lubrication and Shoe Shimming

0

2

3

4

3

0

2

3

0 to 45 4

3

0

2

1

3

2

4

3

9.3 LUBRICATION TABLE

9

The table indicates the quantity of lubricant necessary for every pump size.The table indicates the quantity of lubricant necessary for every pump size. Employ only Vector lubricant for Vector hose pumps. Refer to 6.2 for lubricant emptying and filing.

QUANTITY OF LUBRICANT (LITRES)

.4 SHOE SHIMMING TABLE

Refer to 6.5 to remove or add shims. The table below points out the necessary number of shims under every shoe according to the speed, pressure and the temperature of the product. Respect these indications scrupulously to optimize the hose life and to avoid a possible deterioration of the internal parts.

For temperatures over 140°F, withdraw one shim in comparison with the table below.

For viscosities over 3000cP or concentrations exceeding 300g / l, withdraw one shim in comparison with the table below.

For a suction lift higher than 4 metres, add one shim to the following figures.

CAUTION: Every shoe must include the same number of shims (0.5mm).

PUMPS

4003

(QUARTS)

(QUARTS) 42

0.4

4014

.42 .85 1.5 2.4 6.3 9.5

40

4004

0.8

4006

1.4

4007

2.3

4009

6

4010

9

PUMP TYPE 4006

Pressure bar (psi) Speed - Rpm

∆P ≤ 5 (72.5)

5 (72.5) ≤ ∆P ≤ 7.5 (108.75)

7.5 (108.75) ≤ ∆P ≤ 10 (145)

10 (145) ≤ ∆P ≤ 15 (217.5) 10 (145) ≤ ∆P ≤ 15 (217.5)

PUMP TYPE 4009

Pressure bar (psi) Speed - Rpm

∆P ≤ 5 (72.5)

5 (72.5) ≤ ∆P ≤ 7.5 (108.75)

7.5 (108.75) ≤ ∆P ≤ 10 (145)

10 (145) ≤ ∆P ≤ 15 (217.5)

Wanner Engineering, Inc.

0 to 40

40 to 160

0 to 40

40 to 125

0 to 40

40 to 105

0 to 40

40 to 90

0 to 55

55 to 120

0 to 55

55 to 95

0 to 55

55 to 75

0 to 55

55 to 60

Number of

shims

0

1

2

shims

0

Pressure bar (psi) Speed - Rpm

∆P ≤ 5 (72.5)

5 (72.5) ≤ ∆P ≤ 7.5 (108.75)

7.5 (108.75) ≤ ∆P ≤ 10 (145)

PUMP TYPE 4007

0 to 40

40 to 140

0 to 45

45 to 140

0 to 45

45 to 110

45 to 80

Number of

shims

0

1

2

United States Instant Information: www.vectorpump.com

(612) 332-5681 Fax (612) 332-6937 VEC-991-4000B

35

Vector 4000 Shoe Shimming

0

2

3

4

0

2

3

4

TEMPERATURE

The cover and the pump casing can become very hot due to the friction on the hose and liquid temperature. If you need to limit the pump temperature, please contact your Wanner distributor.

9.4 SHOE SHIMMING TABLE

PUMP TYPE 4010

Pressure bar (psi) Speed - Rpm

0 to 30

30 to 100

0 to 30

30 to 65

0 to 30

30 to 50

0 to 30

30 to 42

∆P ≤ 5 (72.5)

5 (72.5) ≤ ∆P ≤ 7.5 (108.75)

7.5 (108.75) ≤ ∆P ≤ 10 (145)

10 (145) ≤ ∆P ≤ 15 (217.5)

Number of

shims

0

1

2

3

Pressure bar (psi) Speed - Rpm

∆P ≤ 5 (72.5)

5 (72.5) ≤ ∆P ≤ 7.5 (108.75)

7.5 (108.75) ≤ ∆P ≤ 10 (145)

10 (145) ≤ ∆P ≤ 15 (217.5)

PUMP TYPE 4014

0 to 20

20 to 60

0 to 20

20 to 47

0 to 20

20 to 37

0 to 20

20 to 31

Number of

shims

0

1

2

3

9.5 GENERATED NOISE AND TEMPERATURE

NOISE

The Wanner Pumps do not generate more than 60dB during their operation.

1204 Chestnut Avenue, Minneapolis, MN 55403 Tel: (612) 332-5681 Fax: (612) 332-6937 Toll-free fax [US only]: (800) 332-6812 www.vectorpump.com email: sales@wannereng.com

36