Vecow ECS-9700, ECS-9600, ECS-9755, ECS-9755-820Q, ECS-9755-505M User Manual

...

Download

USER Manual

1.1.0 Edition 20161114

ECS-9700/9600

Quad Core Intel® Xeon®/ Core™ i7/ i5/ i3 Fanless Embedded System

High Performance, Rugged, Expandable, Extended Temperature

Version Date Page Description Remark

1.0 11/14/2016 All Ofcial Release

Record of Revision

iii

This manual is released by Vecow Co., Ltd. for reference purpose only. All product offerings and specications are subject to change without prior notice. It does not represent commitment of Vecow Co., Ltd. Vecow shall not be liable for direct, indirect, special, incidental, or consequential damages arising out of the use of the product or documentation or any infringements upon the rights of third parties, which may result from such use.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC

The products described in this manual complies with all applicable European Union (CE) directives if it has a CE marking. For computer systems to remain CE compliant, only CE-compliant parts may be used. Maintaining CE compliance also requires proper cable and cabling techniques.

This document contains proprietary information protected by copyright. No part of this publication may be reproduced in any form or by any means, electric, photocopying, recording or otherwise, without prior written authorization by Vecow Co., Ltd. The rights of all the brand names, product names, and trademarks belong to their respective owners.

Disclaimer

Declaration of Conformity

Part Number Description

ECS-9710-505M ECS-9700, Quad Core Intel® Xeon® E3-1505M v5, 6 GigE LAN

w/ 4 PoE+, 2 SSD Tray, 1 PCIe x16, 6 USB 3.0, 4 COM, 4 SIM, 32 Isolated DIO

ECS-9710-820Q ECS-9700, Quad Core Intel

Core™ i7-6820EQ, 6 GigE LAN w/

4 PoE

, 2 SSD Tray, 1 PCIe x16, 6 USB 3.0, 4 COM, 4 SIM, 32

Isolated DIO

ECS-9710-440Q ECS-9700, Quad Core Intel

Core™ i5-6440EQ, 6 GigE LAN w/ 4 PoE+, 2 SSD Tray, 1 PCIe x16, 6 USB 3.0, 4 COM, 4 SIM, 32 Isolated DIO

ECS-9701-505M ECS-9700, Quad Core Intel

Xeon® E3-1505M v5, 6 GigE LAN w/ 4 PoE+, 2 SSD Tray, 1 PCI, 6 USB 3.0, 4 COM, 4 SIM, 32 Isolated DIO

ECS-9701-820Q ECS-9700, Quad Core Intel

Core™ i7-6820EQ, 6 GigE LAN w/ 4 PoE+, 2 SSD Tray, 1 PCI, 6 USB 3.0, 4 COM, 4 SIM, 32 Isolated DIO

ECS-9701-440Q ECS-9700, Quad Core Intel

Core™ i5-6440EQ, 6 GigE LAN w/ 4 PoE+, 2 SSD Tray, 1 PCI, 6 USB 3.0, 4 COM, 4 SIM, 32 Isolated DIO

ECS-9610-505M ECS-9600, Quad Core Intel

Xeon® E3-1505M v5, 2 GigE LAN, 2 SSD Tray, 1 PCIe x16, 6 USB 3.0, 4 COM, 4 SIM, 16 Isolated DIO

ECS-9610-820Q ECS-9600, Quad Core Intel

Core™ i7-6820EQ, 2 GigE LAN, 2 SSD Tray, 1 PCIe x16, 6 USB 3.0, 4 COM, 4 SIM, 16 Isolated DIO

ECS-9610-440Q ECS-9600, Quad Core Intel

Core™ i5-6440EQ, 2 GigE LAN, 2 SSD Tray, 1 PCIe x16, 6 USB 3.0, 4 COM, 4 SIM, 16 Isolated DIO

ECS-9601-505M

ECS-9600, Quad Core Intel

Xeon® E3-1505M v5, 2 GigE LAN, 2 SSD Tray, 1 PCI, 6 USB 3.0, 4 COM, 4 SIM, 16 Isolated DIO

ECS-9601-820Q

ECS-9600, Quad Core Intel

Core™ i7-6820EQ, 2 GigE LAN, 2 SSD Tray, 1 PCI, 6 USB 3.0, 4 COM, 4 SIM, 16 Isolated DIO

ECS-9601-440Q

ECS-9600, Quad Core Intel

Core™ i5-6440EQ, 2 GigE LAN, 2 SSD Tray, 1 PCI, 6 USB 3.0, 4 COM, 4 SIM, 16 Isolated DIO

Order Information

Part Number Description

DDR4 16G

Certied DDR4 16GB 2133MHz RAM

DDR4 8G

Certied DDR4 8GB 2133MHz RAM

DDR4 4G

Certied DDR4 4GB 2133MHz RAM

PWA-280WB-WT 280W, 24V, 85V AC to 264V AC Power Adaptor with 3-pin

Terminal Block (7.62mm pitch), Wide Temperature -30°C to +70°C

PWA-160WB-WT 160W, 24V, 85V AC to 264V AC Power Adaptor with 3-pin

Terminal Block (7.62mm pitch), Wide Temperature -30°C to +70°C

VESA Mount

VESA Mounting Kit

DIN-RAIL

DIN Rail Kit

Rack Mount

2U Rackmount Kit

TMK2-20P-100

Terminal Block 20-pin to Terminal Block 20-pin Cable, 100cm

TMK2-20P-500

Terminal Block 20-pin to Terminal Block 20-pin Cable, 500cm

TMB-TMBK-20P Terminal Board with One 20-pin Terminal Block Connector

and DIN-Rail Mounting

3G Module

Mini PCIe 3G/GPS Module with Antenna

4G Module

Mini PCIe 4G/GPS Module with Antenna

WiFi & Bluetooth Module

Intel

Mini PCIe WiFi & Bluetooth Module with Antenna

Order Accessories

Table of Contents

CHAPTER 1 GENERAL INTRODUCTION 1

1.1 Overview 1

1.2 Features 2

1.3 Product Specication 2

1.3.1 Specications of ECS-9710 2

1.3.2 Specications of ECS-9701 4

1.3.3 Specications of ECS-9610 7

1.3.4 Specications of ECS-9601 9

1.4 Supported CPU List 11

1.5 Mechanical Dimension 12

1.5.1 Dimensions of ECS-9710/9701 12

1.5.2 Dimensions of ECS-9610/9601 12

CHAPTER 2 GETTING TO KNOW YOUR ECS-9700/9600 13

2.1 Packing List 13

2.2 Front Panel I/O & Functions 14

2.3 Rear Panel I/O & Functions 22

2.4 Main Board Expansion Connectors 30

2.5 Main Board Jumper & Deep Switch Settings 44

2.6 Ignition Control 49

CHAPTER 3 SYSTEM SETUP 52

3.1 How to Open Your ECS-9700/9600 52

3.2 Installing DDR4 SO-DIMM Modules 55

3.3 Installing Mini PCIe Card 56

3.4 Installing CFast Card 57

vii

3.5 Installing SIM Card 58

3.6 Installing PCI/ PCIe Card 59

3.7 Installing SSD/ HDD 61

3.8 Mounting Your ECS-9700/9600 63

CHAPTER 4 BIOS SETUP 69

4.1 Entering BIOS SETUP 69

4.2 Main 70

4.3 Advanced 70

4.4 Chipset 80

4.5 Security 85

4.6 Boot 86

4.7 Save & Exit 87

APPENDIX A : Isolated DIO Guide 88

APPENDIX B : Software Functions 94

APPENDIX C : RAID Installation Guide 96

APPENDIX D : Power Consumption 100

APPENDIX E : Supported Memory & Storage List 104

GENERAL INTRODUCTION

Vecow ECS-9700/9600 Series is a high-performance, all-in-one integrated, expandable fanless embedded system. Powered by 6th generation Quad Core Intel

Xeon®/ Core™ processor (Skylake-H) running with advanced

Intel

CM236 chipset, dual channel DDR4 2133MHz up to 32GB memory, ECS-9700/9600 delivers up to 26% CPU performance improved than former generations with max 80% lower CPU power consumption; Cutting-edge Intel® HD Graphics P530/ 530 graphics engine supports DirectX 12, OpenGL 4.2 and OpenCL 2.0 API, onboard dual DisplayPort and DVI-I display interface support up to Ultra HD 4K resolution, ECS-9700/9600 offers up to 22% improved graphics performance than the former generation; Multiple SATA III (6Gbps), USB 3.0 (5Gbps), PoE (1Gbps) LAN and wireless connections make high-speed data conveying possible. Vecow ECS-9700/9600 Series Expandable Fanless Embedded System brings you new generation system and power productivity to conquer demanding workloads in mission critical real-time embedded computing applications.

All-in-one and cable-less designs, fanless -25°C to 70°C operating temperature, 6 GigE LAN ports with 4 IEEE 802.3at (25.5W/ 48V) PoE

without additional power connections, 2 Front-access 2.5” SSD/ HDD trays, 4 SIM card sockets (3 front-access, 1 internal) for 3G/ 4G/ LTE/ WiFi/ GPRS/ UMTS, 1 Front-access CFast socket, 4 SATA III supports software RAID 0, 1, 5, 10 function, 6 external USB 3.0, 1 PCI/ PCIe x16 expansion slot, 4 COM RS-232/ 422/ 485, 4 Mini PCIe sockets, 32 Isolated DIO, 6V to 36V wide range power input with 80V surge protection, congurable ignition power control, smart remote management features, remote power switch, EN50155 and EN50121-3-2 compliant, optional supports full function SUMIT A, B expansion, Vecow ECS-9700/9600 Series Expandable Fanless Embedded System enables excellent performance, leading integration, user-friendly, smart manageability, mobile availability and rugged reliability possible for performance driven embedded applications.

With excellent performance, leading integrated features, smart manageability, superb mobile availability, secure power protection and rugged reliability, Vecow ECS-9700/9600 Series Expandable Fanless Embedded System is your ideal choices for Machine Vision, Factory Automation, Robot Control, Smart Manufacturing, Mobile DVR/ NVR, Intelligent Surveillance, Industry 4.0 and any Internet of Things (IoT) performance driven real-time embedded computing applications.

1.1 Overview

GENERAL INTRODUCTION

©Vecow ECS-9700/ 9600 User Manual

1.2 Features

• Quad Core Intel® Xeon®/ Core™ i7/ i5/ i3 Processor (Skylake-H) with CM236 Chipset supports up to 4K display

• 2 DDR4 2133MHz Memory, up to 32GB

• Fanless, -25°C to 70°C Operating Temperature

• 6 GigE LAN with 4 IEEE 802.3at PoE+ compliant, iAMT 11.0 supported

• 1 Easy-swap PCI/ PCIe x16 Expansion Slot

• 4 Mini PCIe Slot, 4 COM, 6 USB 3.0

• 4 SIM Card Socket (3 External) support 3G/ 4G/ LTE/ WiFi/ GPRS/ UMTS

• 2 Front-access 2.5" HDD/ SSD Tray, 1 CFast Socket

• 32 Isolated DIO

• Configurable Ignition Power Control

• 6V to 36V DC Power Input with 80V Surge Protection

1.3 Product Specication

1.3.1 Specications of ECS-9710

System

Processor Quad Core Intel® Xeon® E3-1505M v5/ Core™ i7-6820EQ/

i5-6440EQ Processor (Skylake-H)

Chipset Intel

CM236

BIOS AMI

SIO IT8786E

Memory • DDR4 2133MHz

• Up to 32GB

• 2 260-pin SO-DIMM Socket

I/O Interface

Serial 4 COM RS-232/ 422/ 485 w/ auto flow control

USB • 6 USB 3.0 (External)

• 1 USB 2.0 (Internal)

Isolated DIO 32 Isolated DIO (16 DI, 16 DO)

LED Power, HDD, Wireless, PoE

SIM Card 4 SIM Card Socket (3 External, 1 Internal)

Expansion

Mini PCIe 4 Mini PCIe Socket :

• 1 Mini PCIe Socket for PCIe/ USB/ Internal SIM Card/ Optional mSATA

• 3 Mini PCIe Socket for PCIe/ USB/ External SIM Card

GENERAL INTRODUCTION

PCI/ PCIe 1 PCIe x16 Slot

SUMIT A, B 2 SUMIT Slot (Optional)

Graphics

Graphics Processor Intel® HD Graphics P530/ 530

Interface • VGA : Up to 1920 x 1200 @ 60Hz

• DVI-D : Up to 1920 x 1200 @ 60Hz

• DisplayPort 1 : Up to 4096 x 2304 @ 60Hz

• DisplayPort 2 : Up to 4096 x 2304 @ 60Hz

Storage

SATA 4 SATA III support software RAID 0, 1, 5, 10 :

• 3 SATA III (6Gbps)

• 1 SATA III co-lay with Mini PCIe (6Gbps)

mSATA 4 mSATA connection :

• 3 SATA III (Mini PCIe Type, 6Gbps)

• 1 SATA III co-lay with SATA (Mini PCIe Type, 6Gbps)

Storage Device • 1 CFast Socket, Push-in/ Push-out Ejector

• 2 Front-access 2.5" SSD/ HDD Tray

Audio

Audio Codec Realtek ALC892, 5.1 Channel HD Audio

Audio Interface 1 Mic-in, 1 Line-out

Ethernet

LAN 1 Intel® I219 GigE LAN supports iAMT 11.0

LAN 2 Intel

I210 GigE LAN

PoE

LAN 3 GigE IEEE 802.3at (25.5W/48V) PoE+ by Intel® I210

LAN 4 GigE IEEE 802.3at (25.5W/48V) PoE

by Intel® I210

LAN 5 GigE IEEE 802.3at (25.5W/48V) PoE

by Intel® I210

LAN 6 GigE IEEE 802.3at (25.5W/48V) PoE

by Intel® I210

Power

Input Voltage 6V to 36V, DC-in

Power Interface 3-pin Terminal Block : V+, V-, Frame Ground

Ignition Control 16 Mode (Internal)

Remote Switch 3-pin Terminal Block : On, Off, IGN

Surge Protection Up to 80V/1ms Transient Power

Others

TPM Optional Inneon SLB9665 supports TPM 2.0, LPC

interface

Watchdog Timer Reset : 1 to 255 sec./min. per step

GENERAL INTRODUCTION

©Vecow ECS-9700/ 9600 User Manual

Smart Management Wake on LAN, PXE supported

HW Monitor Monitoring temperature, voltages. Auto throttling control

when CPU overheats.

Software Support

OS Windows 10, Windows 8.1, Windows 7, Linux

Mechanical

Dimensions (WxDxH) 260mm x 215mm x 79mm (10.2" x 8.5" x 3.1")

Weight 3.5 kg (7.72 lb)

Mounting • Wallmount by mounting bracket

• DIN Rail Mount (Optional)

• 2U Rackmount (Optional)

Environment

Operating Temperature -25°C to 70°C (-13°F to 158°F)

Storage Temperature -40°C to 85°C (-40°F to 185°F)

Humidity 5% to 95% Humidity, non-condensing

Relative Humidity 95% at 70°C

Shock • IEC 60068-2-27

• SSD : 50G @ Wallmount, Half-sine, 11ms

Vibration • IEC 60068-2-64

• SSD : 5Grms, 5Hz to 500Hz, 3 Axis

EMC CE, FCC, EN50155, EN50121-3-2

1.3.2 Specications of ECS-9701

System

Processor Quad Core Intel® Xeon® E3-1505M v5/ Core™ i7-6820EQ/

i5-6440EQ Processor (Skylake-H)

Chipset Intel

CM236

BIOS AMI

SIO IT8786E

Memory • DDR4 2133MHz

• Up to 32GB

• 2 260-pin SO-DIMM Socket

GENERAL INTRODUCTION

I/O Interface

Serial 4 COM RS-232/ 422/ 485 w/ auto flow control

USB • 6 USB 3.0 (External)

• 1 USB 2.0 (Internal)

Isolated DIO 32 Isolated DIO (16 DI, 16 DO)

LED Power, HDD, Wireless, PoE

SIM Card 4 SIM Card Socket (3 External, 1 Internal)

Expansion

Mini PCIe 4 Mini PCIe Socket :

• 3 Full-size for PCIe/ USB/ External SIM Card/ mSATA

• 1 Full-size for PCIe/ Internal SIM Card/ mSATA

PCI/ PCIe 1 PCI Slot

SUMIT A, B 2 SUMIT Slot (Optional)

Graphics

Graphics Processor Intel® HD Graphics P530/ 530

Interface • VGA : Up to 1920 x 1200 @ 60Hz

• DVI-D : Up to 1920 x 1200 @ 60Hz

• DisplayPort 1 : Up to 4096 x 2304 @ 60Hz

• DisplayPort 2 : Up to 4096 x 2304 @ 60Hz

Storage

SATA 4 SATA III support software RAID 0, 1, 5, 10 :

• 3 SATA III (6Gbps)

• 1 SATA III co-lay with Mini PCIe (6Gbps)

mSATA 4 mSATA connection :

• 3 SATA III (Mini PCIe Type, 6Gbps)

• 1 SATA III co-lay with SATA (Mini PCIe Type, 6Gbps)

Storage Device • 1 CFast Socket, Push-in/ Push-out Ejector

• 2 Front-access 2.5" SSD/ HDD Tray

Audio

Audio Codec Realtek ALC892, 5.1 Channel HD Audio

Audio Interface 1 Mic-in, 1 Line-out

Ethernet

LAN 1 Intel® I219 GigE LAN supports iAMT 11.0

LAN 2 Intel

I210 GigE LAN

PoE

LAN 3 GigE IEEE 802.3at (25.5W/48V) PoE+ by Intel® I210

LAN 4 GigE IEEE 802.3at (25.5W/48V) PoE

by Intel® I210

GENERAL INTRODUCTION

©Vecow ECS-9700/ 9600 User Manual

LAN 5 GigE IEEE 802.3at (25.5W/48V) PoE+ by Intel® I210

LAN 6 GigE IEEE 802.3at (25.5W/48V) PoE

by Intel® I210

Power

Input Voltage 6V to 36V, DC-in

Power Interface 3-pin Terminal Block : V+, V-, Frame Ground

Ignition Control 16 Mode (Internal)

Remote Switch 3-pin Terminal Block : On, Off, IGN

Surge Protection Up to 80V/1ms Transient Power

UPS Supported (Optional)

Others

TPM Optional Inneon SLB9665 supports TPM 2.0, LPC

interface

Watchdog Timer Reset : 1 to 255 sec./min. per step

Smart Management Wake on LAN, PXE supported

HW Monitor Monitoring temperature, voltages. Auto throttling control

when CPU overheats.

Software Support

OS Windows 10, Windows 8.1, Windows 7, Linux

Mechanical

Dimensions (WxDxH) 260mm x 215mm x 79mm (10.2" x 8.5" x 3.1")

Weight 3.5 kg (7.72 lb)

Mounting • Wallmount by mounting bracket

• DIN Rail Mount (Optional)

• 2U Rackmount (Optional)

Environment

Operating Temperature -25°C to 70°C (-13°F to 158°F)

Storage Temperature -40°C to 85°C (-40°F to 185°F)

Humidity 5% to 95% Humidity, non-condensing

Relative Humidity 95% at 70°C

Shock • IEC 60068-2-27

• SSD : 50G @ Wallmount, Half-sine, 11ms

Vibration • IEC 60068-2-64

• SSD : 5Grms, 5Hz to 500Hz, 3 Axis

EMC CE, FCC, EN50155, EN50121-3-2

GENERAL INTRODUCTION

1.3.3 Specications of ECS-9610

System

Processor Quad Core Intel® Xeon® E3-1505M v5/ Core™ i7-6820EQ/

i5-6440EQ Processor (Skylake-H)

Chipset Intel

CM236

BIOS AMI

SIO IT8786E

Memory • DDR4 2133MHz

• Up to 32GB

• 2 260-pin SO-DIMM Socket

I/O Interface

Serial 4 COM RS-232/ 422/ 485 w/ auto flow control

USB • 6 USB 3.0 (External)

• 1 USB 2.0 (Internal)

Isolated DIO 16 Isolated DIO (8 DI, 8 DO)

LED Power, HDD, Wireless

SIM Card 4 SIM Card Socket (3 External, 1 Internal)

Expansion

Mini PCIe 4 Mini PCIe Socket :

• 3 Full-size for PCIe/ USB/ External SIM Card/ mSATA

• 1 Full-size for PCIe/ Internal SIM Card/ mSATA

PCI/ PCIe 1 PCIe x16 Slot

SUMIT A, B 2 SUMIT Slot (Optional)

Graphics

Graphics Processor Intel® HD Graphics P530/ 530

Interface • VGA : Up to 1920 x 1200 @ 60Hz

• DVI-D : Up to 1920 x 1200 @ 60Hz

• DisplayPort 1 : Up to 4096 x 2304 @ 60Hz

• DisplayPort 2 : Up to 4096 x 2304 @ 60Hz

Storage

SATA 4 SATA III support software RAID 0, 1, 5, 10 :

• 3 SATA III (6Gbps)

• 1 SATA III co-lay with Mini PCIe (6Gbps)

mSATA 4 mSATA connection :

• 3 SATA III (Mini PCIe Type, 6Gbps)

• 1 SATA III co-lay with SATA (Mini PCIe Type, 6Gbps)

Storage Device • 1 CFast Socket, Push-in/ Push-out Ejector

• 2 Front-access 2.5" SSD/ HDD Tray

GENERAL INTRODUCTION

©Vecow ECS-9700/ 9600 User Manual

Audio

Audio Codec Realtek ALC892, 5.1 Channel HD Audio

Audio Interface 1 Mic-in, 1 Line-out

Ethernet

LAN 1 Intel® I219LM GigE LAN supports iAMT 11.0

LAN 2 Intel

I210 GigE LAN

Power

Input Voltage 6V to 36V, DC-in

Power Interface 3-pin Terminal Block : V+, V-, Frame Ground

Ignition Control 16 Mode (Internal)

Remote Switch 3-pin Terminal Block : On, Off, IGN

Surge Protection Up to 80V/1ms Transient Power

Others

TPM Optional Inneon SLB9665 supports TPM 2.0, LPC

interface

Watchdog Timer Reset : 1 to 255 sec./min. per step

Smart Management Wake on LAN, PXE supported

HW Monitor Monitoring temperature, voltages. Auto throttling control

when CPU overheats.

Software Support

OS Windows 10, Windows 8.1, Windows 7, Linux

Mechanical

Dimensions (WxDxH) 260mm x 215mm x 79mm (10.2" x 8.5" x 3.1")

Weight 3.5 kg (7.72 lb)

Mounting • Wallmount by mounting bracket

• DIN Rail Mount (Optional)

• 2U Rackmount (Optional)

Environment

Operating Temperature -25°C to 70°C (-13°F to 158°F)

Storage Temperature -40°C to 85°C (-40°F to 185°F)

Humidity 5% to 95% Humidity, non-condensing

Relative Humidity 95% at 70°C

Shock • IEC 60068-2-27

• SSD : 50G @ Wallmount, Half-sine, 11ms

Vibration • IEC 60068-2-64

• SSD : 5Grms, 5Hz to 500Hz, 3 Axis

EMC CE, FCC, EN50155, EN50121-3-2

GENERAL INTRODUCTION

1.3.4 Specications of ECS-9601

System

Processor Quad Core Intel® Xeon® E3-1505M v5/ Core™ i7-6820EQ/

i5-6440EQ Processor (Skylake-H)

Chipset Intel

CM236

BIOS AMI

SIO IT8786E

Memory • DDR4 2133MHz

• Up to 32GB

• 2 260-pin SO-DIMM Socket

I/O Interface

Serial 4 COM RS-232/ 422/ 485 w/ auto flow control

USB • 6 USB 3.0 (External)

• 1 USB 2.0 (Internal)

Isolated DIO 16 Isolated DIO (8 DI, 8 DO)

LED Power, HDD, Wireless

SIM Card 4 SIM Card Socket (3 External, 1 Internal)

Expansion

Mini PCIe 4 Mini PCIe Socket :

• 3 Full-size for PCIe/ USB/ External SIM Card/ mSATA

• 1 Full-size for PCIe/ Internal SIM Card/ mSATA

PCI/ PCIe 1 PCI Slot

SUMIT A, B 2 SUMIT Slot (Optional)

Graphics

Graphics Processor Intel® HD Graphics P530/ 530

Interface • VGA : Up to 1920 x 1200 @ 60Hz

• DVI-D : Up to 1920 x 1200 @ 60Hz

• DisplayPort 1 : Up to 4096 x 2304 @ 60Hz

• DisplayPort 2 : Up to 4096 x 2304 @ 60Hz

Storage

SATA 4 SATA III support software RAID 0, 1, 5, 10 :

• 3 SATA III (6Gbps)

• 1 SATA III co-lay with Mini PCIe (6Gbps)

mSATA 4 mSATA connection :

• 3 SATA III (Mini PCIe Type, 6Gbps)

• 1 SATA III co-lay with SATA (Mini PCIe Type, 6Gbps)

Storage Device • 1 CFast Socket, Push-in/ Push-out Ejector

• 2 Front-access 2.5" SSD/ HDD Tray

GENERAL INTRODUCTION

©Vecow ECS-9700/ 9600 User Manual

Audio

Audio Codec Realtek ALC892, 5.1 Channel HD Audio

Audio Interface 1 Mic-in, 1 Line-out

Ethernet

LAN 1 Intel® I219LM GigE LAN supports iAMT 11.0

LAN 2 Intel

I210 GigE LAN

Power

Input Voltage 6V to 36V, DC-in

Power Interface 3-pin Terminal Block : V+, V-, Frame Ground

Ignition Control 16 Mode (Internal)

Remote Switch 3-pin Terminal Block : On, Off, IGN

Surge Protection Up to 80V/1ms Transient Power

Others

TPM Optional Inneon SLB9665 supports TPM 2.0, LPC

interface

Watchdog Timer Reset : 1 to 255 sec./min. per step

Smart Management Wake on LAN, PXE supported

HW Monitor Monitoring temperature, voltages. Auto throttling control

when CPU overheats.

Software Support

OS Windows 10, Windows 8.1, Windows 7, Linux

Mechanical

Dimensions (WxDxH) 260mm x 215mm x 79mm (10.2" x 8.5" x 3.1")

Weight 3.5 kg (7.72 lb)

Mounting • Wallmount by mounting bracket

• DIN Rail Mount (Optional)

• 2U Rackmount (Optional)

Environment

Operating Temperature -25°C to 70°C (-13°F to 158°F)

Storage Temperature -40°C to 85°C (-40°F to 185°F)

Humidity 5% to 95% Humidity, non-condensing

Relative Humidity 95% at 70°C

Shock • IEC 60068-2-27

• SSD : 50G @ Wallmount, Half-sine, 11ms

Vibration • IEC 60068-2-64

• SSD : 5Grms, 5Hz to 500Hz, 3 Axis

EMC CE, FCC, EN50155, EN50121-3-2

GENERAL INTRODUCTION

1.4 Supported CPU List

Processor No. TDP Cache Max. Frequency Embedded

Xeon

E3-1575M v5 45W 8M Up to 3.00 GHz

Xeon

E3-1545M v5 45W 8M Up to 2.90 GHz

Xeon

E3-1535M v5 45W 8M Up to 2.80 GHz

Xeon

E3-1515M v5 45W 8M Up to 2.80 GHz

Xeon

E3-1505M v5 45W 8M Up to 2.80 GHz Yes

Xeon

E3-1505L v5 25W 8M Up to 2.00 GHz

Core i7-6970HQ 45W 8M Up to 3.70 GHz

Core i7-6920HQ 45W 8M Up to 3.80 GHz

Core i7-6870HQ 45W 8M Up to 3.60 GHz

Core i7-6820HQ 45W 8M Up to 3.60 GHz

Core i7-6770HQ 45W 6M Up to 3.50 GHz

Core i7-6700HQ 45W 6M Up to 3.50 GHz

Core i7-6820EQ 45W 8M Up to 3.50 GHz Ye s

Core i7-6822EQ 25W 8M Up to 2.80 GHz

Core i5-6440HQ 45W 6M Up to 3.50 GHz

Core i5-6350HQ 45W 6M Up to 3.20 GHz

Core i5-6300HQ 45W 6M Up to 3.20 GHz

Core i5-6440EQ 45W 6M Up to 3.40 GHz Ye s

Core i5-6442EQ 45W 6M Up to 2.70 GHz

GENERAL INTRODUCTION

©Vecow ECS-9700/ 9600 User Manual

1.5 Mechanical Dimension

1.5.1 Dimensions of ECS-9710/9701

260.0 (10.24”)

282.0 (11.10”)

297.0 (11.69”)

155.0 (6.10”)

215.0 (8.46”)

79.1 (3.11”)

Unit: mm (inch)

1.5.2 Dimensions of ECS-9610/9601

260.0 (10.24”)

282.0 (11.10”)

297.0 (11.69”)

155.0 (6.10”)

215.0 (8.46”)

79.1 (3.11”)

Unit: mm (inch)

GETTING TO KNOW YOUR ECS-9700/ 9600

GETTING TO KNOW YOUR ECS-9700/9600

2.1 Packing List

Item Description Qty

1 ECS-9700/9600 Expandable Fanless Embedded System

(According to the conguration you order, the ECS-9700/9600 series may contain SSD/HDD and DDR4 SO-DIMM. Please verify these items if necessary.)

2 ECS-9700-Accessory box, which contains

● Vecow Drivers & Utilities DVD

● Wall-mounting bracket

● KHS#6-32x6 screw for wall-mounting bracket

● M2.5x6 screw for Mini PCIe Slot

● Din-Rail-PH-M4x16.5-S Ni

● 3-pin pluggable terminal block

● 20-pin pluggable terminal block

● Foot Pad

● F-M3x4 for SSD/HDD screws

1 2 4 4 4 2 2 4 4

3 ECS-9600-Accessory box, which contains

● Vecow Drivers & Utilities DVD

● Wall-mounting bracket

● KHS#6-32x6 screw for wall-mounting bracket

● M2.5x6 screw for Mini PCIe Slot

● Din-Rail-PH-M4x16.5-S Ni

● 3-pin pluggable terminal block

● 20-pin pluggable terminal block

● Foot Pad

● F-M3x4 for SSD/HDD screws

1 2 4 4 4 2 1 4 4

GETTING TO KNOW YOUR ECS-9700/ 9600©Vecow ECS-9700/ 9600 User Manual

2.2 Front Panel I/O & Functions

In Vecow ECS-9700/9600 series family, all I/O connectors are located on front panel and rear panel. Most of the general connections to computer device, such as USB, LAN Jack, Audio, VGA, Display, DVI-D and any additional storage, are placed on the front panel.

RST

DP LAN 1

LAN 2

DVI-D

VGA

CFast

SIM 1 SIM 3

SIM 2

1 2 3 4

WLAN

2.2.1 Power Button

The Power Button is a non-latched switch with dual color LED indication. It indicates power status: S0, S3 and S5. More detail LED indications are listed as follows:

To power on ECS-9700, press the power button and then the blue LED is lightened. To power off ECS-9700, you can either command shutdown by OS operation, or just simply press the power button.

If system error, you can just press the power button for 4 seconds to shut down the machine directly. Please do note that a 4-second interval between each 2 power-on/ power-off operation is necessary in normal working status. (For example, once turning off ECS-9700, you have to wait for 4 seconds to initiate another power-on operation).

LED Color Power Status System Status

Solid Blue S0 System working

Solid Orange S3, S5 Suspend to RAM, System off with standby power

RST

DP LAN 1

LAN 2

DVI-D

VGA

CFast

SIM 1 SIM 3

SIM 2

1 2 3 4

WLAN

GETTING TO KNOW YOUR ECS-9700/ 9600

Pin No. Description Pin No. Description

S1 GND PC6 NC

S2 SATA_TXP5 PC7 GND

S3 SATA_TXN5 PC8 CFAST_LED

S4 GND PC9 NC

S5 SATA_RXN5 PC10 NC

S6 SATA_RXP5 PC11 NC

S7 GND PC12 NC

2.2.3 CFast Card

There is a CFast socket on the front panel supporting Type-I/II Compact Flash card. It is implemented by a SATA III Port from CM236 PCH. Be sure to disconnect the power source and unscrew the CFast socket cover before installing a CFast card. The ECS-9700 does not support the CFast hot swap and PnP (Plug and Play) functions. It is necessary to remove power source rst before inserting or removing the CFast card.

The pinouts of CFast port are listed as follows:

RST

DP LAN 1

LAN 2

DVI-D

VGA

CFast

SIM 1 SIM 3

SIM 2

1 2 3 4

WLAN

2.2.2 Reset Tact Switch

It is a hardware reset switch. Use this switch to reset ECS-9700 without power off. Press the Reset Switch for a few seconds, then reset will be enabled.

RST

DP LAN 1

LAN 2

DVI-D

VGA

CFast

SIM 1 SIM 3

SIM 2

1 2 3 4

WLAN

GETTING TO KNOW YOUR ECS-9700/ 9600©Vecow ECS-9700/ 9600 User Manual

Pin No. Description Pin No. Description

PC1 GND PC13 +3.3V

PC2 GND PC14 +3.3V

PC3 NC PC15 GND

PC4 NC PC16 GND

PC5 NC PC17 NC

2.2.4 PWR and HDD LED Indicator

HDD LED/ Yellow: A Hard Disk/ CFast LED. If the LED is on, it indicates ECS9700 storage is functional. If it is off, it indicates ECS-9700 storage is not functional. If it is ashing, it indicates data access activities.

Power LED/ Green: If the LED is solid green, it indicates ECS-9700 is powered on.

LED Color Power Status System Status

Yellow HDD/ CFast

• On/ Off : Storage status, function or not.

• Twinkling : Data transferring.

Green Power System power status (on/ off)

RST

DP LAN 1

LAN 2

DVI-D

VGA

CFast

SIM 1 SIM 3

SIM 2

1 2 3 4

WLAN

2.2.5 DVI-D Connector

RST

DP LAN 1

LAN 2

DVI-D

VGA

CFast

SIM 1 SIM 3

SIM 2

1 2 3 4

WLAN

GETTING TO KNOW YOUR ECS-9700/ 9600

The DVI-D connector on the front panel supports DVI display. This connector can output DVI signal. The DVI output mode supports up to 1920 x 1200 resolution and the DVI is automatically selected according to the display device connected. You will need a DVI-D cable when connecting to a display device.

2.2.7 DisplayPort

Onboard Display Port supports auxiliary channel dual mode and the connection supports up to 4096x2304 resolution at 60 Hz. Multi-Stream Transport Display Resolutions Table:

RST

DP LAN 1

LAN 2

DVI-D

VGA

CFast

SIM 1 SIM 3

SIM 2

1 2 3 4

WLAN

Multi-Stream Transport Display Max. Resolution

One panel Display 4096x2304@60Hz

Two panel Displays concurrently 2880x1800@60Hz

Three panel Displays concurrently 2304x1440@60Hz

2.2.6 VGA Connector

The VGA connector on the front panel supports VGA display. This VGA connector comes from eDP and the VGA output mode supports up to 1920 x 1200 resolution. Remark: This VGA connector does not support Hot Plug function. If you would like to use the VGA connector, please remain the connection of VGA Display.

RST

DP LAN 1

LAN 2

DVI-D

VGA

CFast

SIM 1 SIM 3

SIM 2

1 2 3 4

WLAN

GETTING TO KNOW YOUR ECS-9700/ 9600©Vecow ECS-9700/ 9600 User Manual

2.2.8 USB 3.0

There are 4 USB 3.0 connections available supporting up to 5GB per second data rate in the front side of ECS-9700/9600. It is also compliant with the requirements of Super Speed (SS), high speed (HS), full speed (FS) and low speed (LS).

RST

DP LAN 1

LAN 2

DVI-D

VGA

CFast

SIM 1 SIM 3

SIM 2

1 2 3 4

WLAN

2.2.9 Ethernet Port

There are 2 8-pin RJ-45 jacks supporting 10/100/1000 Mbps Ethernet connections in the front side. LAN 1 is powered by Intel i219 Ethernet Phy; LAN 2 is powered by Intel I210 Ethernet engine. When both LAN 1 and LAN 2 work in normal status, iAMT 11.0 function is enabled.

Using suitable RJ-45 cable, you can connect the system to other computers, or to any other devices with Ethernet connection; for example, a hub or a switch. Moreover, both LAN 1 and LAN 2 support Wake on LAN and Pre-boot functions. The pin-outs of LAN 1 and LAN 2 are listed as follows:

RST

DP LAN 1

LAN 2

DVI-D

VGA

CFast

SIM 1 SIM 3

SIM 2

1 2 3 4

WLAN

Pin No. 10/ 100Mbps 1000Mbps

1 E_TX+ MDI0_P

2 E_TX- MDI0_N

3 E_RX+ MDI1_P

GETTING TO KNOW YOUR ECS-9700/ 9600

Each LAN port is supported by standard RJ-45 connector with LED indicators to present Active/ Link/ Speed status of the connection.

The LED indicator on the right bottom corner lightens in solid green when the cable is properly connected to a 100 Mbps Ethernet network,and it lightens in solid orange when the cable is properly connected to a 1000Mbps Ethernet network. The left LED will keep twinkling/ off when Ethernet data packets are being transmitted/ received.

1 8

10Mbps 100Mbps 1000Mbps

Right

Bottom Led

Off Solid

Green

Solid

Orange

Left

Bottom Led

Flash

Yellow

Flash

Yellow

Flash

Yellow

4 ---- MDI2_P

5 ----- MDI2_N

6 E_RX- MDI1_N

7 ----- MDI3_P

8 ------ MDI3_N

2.2.10 Audio Jack

There are 2 audio connectors, Mic-in and Line-out, in the front side of ECS-9700. Onboard Realtek ALC892 audio codec supports 5.1 channel HD audio and fully complies with Intel® High Denition Audio (Azalia) specications.

To utilize the audio function in Windows platform, you need to install corresponding drivers for both Intel CM236 chipset and Realtek ALC892 codec.

RST

DP LAN 1

LAN 2

DVI-D

VGA

CFast

SIM 1 SIM 3

SIM 2

1 2 3 4

WLAN

GETTING TO KNOW YOUR ECS-9700/ 9600©Vecow ECS-9700/ 9600 User Manual

2.2.11 WLAN LED, Mini PCIe, SIM Card Comparison

RST

DP LAN 1

LAN 2

DVI-D

VGA

CFast

SIM 1 SIM 3

SIM 2

1 2 3 4

WLAN

Mini PCIe SIM LED

Mini PCIe 1 / mSATA (CN12) SIM 1 (CN13) 1

Mini PCIe 2 / mSATA (CN8) SIM 2 (CN9) 2

Mini PCIe 3 / mSATA (CN10) SIM 3 (CN11) 3

Mini PCIe 4 / mSATA (CN6) SIM 4 (CN7) 4

Mini PCIe Slot/ SIM Slot/ WLAN LED Mapping Table :

Mini PCIe 3

CN10

Mini PCIe 2

CN8

Mini PCIe 1

CN12

Mini PCIe 4

CN6

SIM2

CN9

SW2

Note: A. The SIM card sockets do not support hot-plug. Please make sure to unplug the system power before inserting the SIM card(s). SW2: Mini PCIe 1to 4; PCIe & mSATA Select SW

Mini PCIe

4 only supports PCIe interface SIM card module

DIP Switch Interface

SW2-1

Mini PCIe 1

ON Mini PCIe

OFF Auto Detection

(Default)

SW2-2

Mini PCIe 2

ON Mini PCIe

OFF Auto Detection

(Default)

DIP Switch Interface

SW2-3

Mini PCIe 3

ON Mini PCIe

OFF Auto Detection

(Default)

SW2-4

Mini PCIe 4

ON Mini PCIe

OFF Auto Detection

(Default)

SIM4

CN6

GETTING TO KNOW YOUR ECS-9700/ 9600

HDD Tray MB Connector MB Power Connector

HDD 1 SATA1 Power Conn 1

HDD 2 SATA2 Power Conn 1

SATA3 Power Conn 2

SATA4

(Remark: By MB BOM Optional,

Default no signal link)

Power Conn 2

2.2.12 SSD/ HDD Tray

There are 2 front-access 2.5” SSD/ HDD trays in the front side of ECS-9700. Just trigger to open the SSD/ HDD tray, up to 8TB is available.

RST

DP LAN 1

LAN 2

DVI-D

VGA

CFast

SIM 1 SIM 3

SIM 2

1 2 3 4

WLAN

HDD 1

HDD 2

SATA3 SATA1

SATA4 SATA2

SATA Power Conn1

SATA Power Conn2

GETTING TO KNOW YOUR ECS-9700/ 9600©Vecow ECS-9700/ 9600 User Manual

2.3 Rear Panel I/O & Functions

2.3.1 Power Terminal Block

2.3.2 Remote Power On/ O Switch & Ignition

COM 2

COM 1

COM 3COM 4

V+ V

On | Off

DC-IN

IGN

LAN6

PoE

LAN5

PoE

LAN4

PoE

LAN3

PoE

Isolated

DIO 2

D IPIN 1 ~ 8 DOPIN 11 ~ 18

20 11

10 1

Isolated

DIO 1

D IPIN 1 ~ 8 DOPIN 11 ~ 18

20 11

10 1

It is a 5-pin power-on or power-off switch through Phoenix Contact terminal block. You could turn on or off the system power by using this contact. This terminal block supports dual function of soft power-on/ power-off (instant off or delay 4 second), and suspend mode.

Pin No. Denition Pin No. Denition

1 Ignition 2 External Power Button V+

3 External Power Button V-

This system supports 6V to 36V DC power input by terminal block in the rear side. In normal power operation, power LED lightens in solid green and supports up to 80V surge protection.

COM 2

COM 1

COM 3COM 4

V+ V

On | Off

DC-IN

IGN

LAN6

PoE

LAN5

PoE

LAN4

PoE

LAN3

PoE

Isolated

DIO 2

D IPIN 1 ~ 8 DOPIN 11 ~ 18

20 11

10 1

Isolated

DIO 1

D IPIN 1 ~ 8 DOPIN 11 ~ 18

20 11

10 1

Pin No. Denition Pin No. Denition

1 V+ 2 V-

3 Chassis Ground

GETTING TO KNOW YOUR ECS-9700/ 9600

Serial

Port

Pin No. RS-232 RS-422

(5-wire)

RS-422 (9-wire)

RS-485 (3-wire)

1 to 4

1 DCD TXD- TXD- DATA-

2 RXD TXD+ TXD+ DATA+

3 TXD RXD+ RXD+ -----------

4 DTR RXD- RXD- -----------

5 GND GND GND GND

6 DSR ----------- RTS- -----------

7 RTS ----------- RTS+ -----------

8 CTS ----------- CTS+ -----------

9 RI ----------- CTS- -----------

The pin assignments are listed in the table as below:

BIOS Setting Function

COM 1

COM 2

COM 3

COM 4

RS-232

RS-422 (5-wire)

RS-422 (9-wire)

RS-485

RS-485 w/z auto-ow control

2.3.3 COM Ports

Serial port 1 to 4 (COM 1 to 4) can be congured for RS-232, RS-422, or RS485 with auto ow control communication. The default denition of COM 1 and COM 2 is RS-232. If you want to change to RS-422 or RS-485, you can nd the setting in BIOS.

COM 2

COM 1

COM 3COM 4

V+ V

On | Off

DC-IN

IGN

LAN6

PoE

LAN5

PoE

LAN4

PoE

LAN3

PoE

Isolated

DIO 2

D IPIN 1 ~ 8 DOPIN 11 ~ 18

20 11

10 1

Isolated

DIO 1

D IPIN 1 ~ 8 DOPIN 11 ~ 18

20 11

10 1

GETTING TO KNOW YOUR ECS-9700/ 9600©Vecow ECS-9700/ 9600 User Manual

COM3 & COM 4 MB connector table:

COM Port MB Connector COM Port MB Connector

COM 3 CN27 COM 4 CN28

CN Pin No. Signal Name

CN27(COM3)

CN28(COM4)

1 Chassis GND

2 GND

3 RI

4 DTR

5 CTS

6 TXD

7 RTS

8 RXD

9 DSR

10 DCD

COM 3 & COM 4 MB connector pin out:

CN27

COM3

CN28

COM4

GETTING TO KNOW YOUR ECS-9700/ 9600

2.3.5 PoE (Power over Ethernet) Ports

There are 4 8-pin POE RJ-45 jacks supporting 10/100/1000 Mbps Ethernet connections in the front side powered by Intel I210 Ethernet engine. When both LAN 1 and LAN 2 work in normal status, iAMT 11.0 function is enabled. Each POE supports 30.4W

COM 2

COM 1

COM 3COM 4

V+ V

On | Off

DC-IN

IGN

LAN6

PoE

LAN5

PoE

LAN4

PoE

LAN3

PoE

Isolated

DIO 2

D IPIN 1 ~ 8 DOPIN 11 ~ 18

20 11

10 1

Isolated

DIO 1

D IPIN 1 ~ 8 DOPIN 11 ~ 18

20 11

10 1

Pin No. 10/ 100 Mbps 1000 Mbps PoE

1 E_TX+ MDI0_P PoE+

2 E_TX- MDI0_N PoE+

3 E_RX+ MDI1_P PoE-

4 ---- MDI2_P ----

5 ----- MDI2_N ----

6 E_RX- MDI1_N PoE-

7 ----- MDI3_P ----

8 ------ MDI3_N ----

2.3.4 Rear USB 3.0

There are 2 USB 3.0 connections available supporting up to 5GB per second data rate in the front side of ECS-9700. It also compliant with the requirements of Super Speed (SS), high speed (HS), full speed (FS) and low speed (LS).

COM 2

COM 1

COM 3COM 4

V+ V

On | Off

DC-IN

IGN

LAN6

PoE

LAN5

PoE

LAN4

PoE

LAN3

PoE

Isolated

DIO 2

D IPIN 1 ~ 8 DOPIN 11 ~ 18

20 11

10 1

Isolated

DIO 1

D IPIN 1 ~ 8 DOPIN 11 ~ 18

20 11

10 1

GETTING TO KNOW YOUR ECS-9700/ 9600©Vecow ECS-9700/ 9600 User Manual

Each LAN port is supported by standard RJ-45 connector with LED indicators to present Active/ Link/ Speed status of the connection.

The LED indicator on the right bottom corner lightens in solid green when the cable is properly connected to a 100 Mbps Ethernet network, and it lightens in solid orange when the cable is properly connected to a 1000 Mbps Ethernet network. The left LED will keep twinkling/ off when Ethernet data packets are being transmitted/ received.

1 8

LED Status 10Mbps 100Mbps 1000Mbps

Right

Bottom Led

Off

Solid

Green

Solid

Orange

Left

Bottom Led

Flash

Yellow

Flash

Yellow

Flash

Yellow

LED Location LED Color Status

LAN3 Green

Green Light: PD installed & powered green

Off: Non PD

LAN4 Green

Green Light: PD installed & powered green

Off: Non PD

LAN5 Green

Green Light: PD installed & powered green

Off: Non PD

LAN6 Green

Green Light: PD installed & powered green

Off: Non PD

POE LED indicator:

GETTING TO KNOW YOUR ECS-9700/ 9600

2.3.6 Isolated DIO

COM 2

COM 1

COM 3COM 4

V+ V

On | Off

DC-IN

IGN

LAN6

PoE

LAN5

PoE

LAN4

PoE

LAN3

PoE

Isolated

DIO 2

D IPIN 1 ~ 8 DOPIN 11 ~ 18

20 11

10 1

Isolated

DIO 1

D IPIN 1 ~ 8 DOPIN 11 ~ 18

20 11

10 1

There is a 32-bit (16-bit DI, 16-bit DO) with 2 DIO connectors in the rear side. DI / DIO support NPN(sink) and PNP(Source) mode, Each DI channel is equipped with a photocouper for isolated protection. Each DO with isolator chip is congured by a Jumper for each DIO connector. DO Safety-Related Certications:

• 4242-VPK Basic Isolation per DIN V VDE V 0884-10 and DIN EN 61010-1

• 3-KVRMS Isolation for 1 minute per UL 1577

• CSA Component Acceptance Notice 5A, IEC 60950-1 and IEC 61010-1 End Equipment Standards

• GB4943.1-2011 CQC Certied

Isolated

DIO

D IPIN 1 ~ 8 DOPIN 11 ~ 18

20 11

10 1

DIO Pin No. Denition Function

DIO1

1 INPUT 0 SIO_GPI80

2 INPUT 1 SIO_GPI81

3 INPUT 2 SIO_GPI82

4 INPUT 3 SIO_GPI83

5 INPUT 4 SIO_GPI84

6 INPUT 5 SIO_GPI85

7 INPUT 6 SIO_GPI86

8 INPUT 7 SIO_GPI87

9 DI1_COM -

10 DIO1_GND -

11 OUTPUT 0 SIO_GPO70

12 OUTPUT 1 SIO_GPO71

13 OUTPUT 2 SIO_GPO72

14 OUTPUT 3 SIO_GPO73

15 OUTPUT 4 SIO_GPO74

16 OUTPUT 5 SIO_GPO75

17 OUTPUT 6 SIO_GPO76

18 OUTPUT 7 SIO_GPO77

19 DIO1_GND -

20 DIO1_VDC (6~48V Input) -

DIO Connectors pin out:

GETTING TO KNOW YOUR ECS-9700/ 9600©Vecow ECS-9700/ 9600 User Manual

DIO Pin No. Denition Function

DIO2

1 INPUT 8 SIO_GPI37

2 INPUT 9 SIO_GPI50

3 INPUT 10 SIO_GPI51

4 INPUT 11 SIO_GPI52

5 INPUT 12 SIO_GPI56

6 INPUT 13 SIO_GPI57

7 INPUT 14 SIO_GPI64

8 INPUT 15 SIO_GPI65

9 DI2_COM -

10 DIO2_GND -

11 OUTPUT 8 SIO_GPO11

12 OUTPUT 9 SIO_GPO12

13 OUTPUT 10 SIO_GPO15

14 OUTPUT 11 SIO_GPO16

15 OUTPUT 12 SIO_GPO32

16 OUTPUT 13 SIO_GPO33

17 OUTPUT 14 SIO_GPO35

18 OUTPUT 15 SIO_GPO36

19 DIO2_GND -

20 DIO2_VDC (6~48V Input) -

DI reference circuit:

Sink Mode (NPN)

V+

V-

Power Supply

6-48V DC

DI_COM (Pin 9)

DI (Pin1-8)

DIO Connector

Source Mode (PNP)

V+

V-

Power Supply

6-48V DC

DI_COM (Pin 9)

DI (Pin1-8)

DIO Connector

DIO Jumper Setting Status

DIO1 JP10 1-2 (Default)

NPN (Sink Mode):

Max. Input current 100mA / 6 ~48V

DIO1 JP10 2-3

PNP (Source Mode):

Max. output current 100mA / 6 ~48V

DIO2 JP11 1-2 (Default)

NPN (Sink Mode):

Max. Input current 100mA / 6 ~48V

DIO2 JP11 2-3

PNP (Source Mode):

Max. output current 100mA / 6 ~48V

DO Jumper Setting Table:

GETTING TO KNOW YOUR ECS-9700/ 9600

JP11 JP10

DO reference circuit:

2.3.7 Add Card

Optional for PCIEx16 FHHL add on card or PCI card.

COM 2

COM 1

COM 3COM 4

V+ V

On | Off

DC-IN

IGN

LAN6

PoE

LAN5

PoE

LAN4

PoE

LAN3

PoE

Isolated

DIO 2

D IPIN 1 ~ 8 DOPIN 11 ~ 18

20 11

10 1

Isolated

DIO 1

D IPIN 1 ~ 8 DOPIN 11 ~ 18

20 11

10 1

V+

V-

Device

6-48V DC

DIO_VDC (Pin 20)

DO (Pin11-18)

DIO_GND (Pin10,19)

DIO Connector

Source Mode (PNP)

Sink Mode (NPN, Default)

V+

V-

Device

6-48V DC

DIO_VDC (Pin 20)

DO (Pin11-18)

DIO_GND (Pin10,19)

DIO Connector

GETTING TO KNOW YOUR ECS-9700/ 9600©Vecow ECS-9700/ 9600 User Manual

2.4 Main Board Expansion Connectors

2.4.1 Inside View of ECS-9700 Main Board With Connector Location

FN1

SATA 1

SATA 2

CN27

CN5

CN28

JP2

J9 J8

SATA 3

SATA 4

CN1

SW2

JP7

JP10

JP8

CN2

J10

SW5

JP11

SW7

SW11

CN20

CN3

JP1

JP3

BAT

J11

SUMITB

SUMITA

CFast

CN36

CN9

CN6

CN10

CN12

JP5 JP6

JP9

CN8

CN7

JP4

BZ1

SW3 SW4

GETTING TO KNOW YOUR ECS-9700/ 9600

2.4.2 UPS Power Connector

For UPS module optional, we use 4.2mm 2x2p power connector. This system has a UPS power input connector for Optional part UPS Module.

Pin No. Denition Pin No. Denition

1 Ground 2 Ground

+VDC_IN

(6~36V, Max.8A)

+VDC_IN

(6~36V, Max.8A)

CN36

2.4.3 Miscellaneous Pin Header

2.0mm 2x4p header This pin header can be used as a backup for following functions, such as hard drive LED indicator, reset button, power LED indicator, and power-on/ off button, which already can be accessed by front panel and top panel. The pin-outs of Miscellaneous port are listed in following table:

J11

GETTING TO KNOW YOUR ECS-9700/ 9600©Vecow ECS-9700/ 9600 User Manual

Group Pin No. Description

HDD LED

1 HDD_LED_P

3 HDD_LED_N

RESET BUTTON

5 FP_RST_BTN_N

7 Ground

POWER LED

2 PWR_LED_P

4 PWR_LED_N

POWER BUTTON

6 FP_PWR_BTN_IN

8 Ground

2.4.4 DDR4 Slot

There are 2 DDR4 channel onboard and support DDR4 2133/1866, max 32GB. (each channel 16GB)

Slot Description Slot Description

Slot1 / U2 DDR4 Channel A Slot2 / U3 DDR4 Channel B

GETTING TO KNOW YOUR ECS-9700/ 9600

2.4.5 BIOS Socket

If the BIOS needs to be changed, please contact the Vecow RMA service team.

CN1

2.4.6 SATA Connector

Standard 7 PIN SATA Connector There are 4 onboard high performance Serial ATA III. It supports higher storage capacity with less cabling effort and smaller required space. SATA4 is only for BOM option, default without function.

SATA 1

SATA 2

SATA 3

SATA 4

Pin No. Denition

1 Ground

2 TX DP

3 TX DN

4 Ground

Pin No. Denition

5 RX DN

6 RX DP

7 Ground

GETTING TO KNOW YOUR ECS-9700/ 9600©Vecow ECS-9700/ 9600 User Manual

2.4.7 SATA Power Header

Standard, all form factor 1x4p power header There are 2 HDD power header on board and each power header supports two

2.5” SATA HDD.

Pin No. Description Pin No. Description

1 +V5 (Max. 4A) 2 Ground

3 Ground 4 +V12 (Max. 1.5A)

2.4.8 Internal USB2.0

Standard Vertical USB2.0 Connector. ECS-9700 main board provides one expansion USB port using plug-and-play for dongle key or LCD touch panel. The USB interface supports 480 Mbps transfer rate complied with high speed USB specication Rev. 2.0.

The USB interface is accessed through one standard USB 2.0 connector. This USB 2.0 does not support wake up function.

GETTING TO KNOW YOUR ECS-9700/ 9600

2.4.9 SUMIT A, SUMIT B

This system has standard SUMIT A and SUMIT B for SUMIT type add on cards.

SUMITB

SUMITA

Pin No. Denition Pin No. Denition

1 USB +VCC (+V5/Max. 0.5A) 2 D ATA-

3 DATA+ 4 Ground

CN20

GETTING TO KNOW YOUR ECS-9700/ 9600©Vecow ECS-9700/ 9600 User Manual

Pin No. Function Pin No. Function

1 +5V_AUX 2 +12V

3 +3.3V 4 SMB_DATA

5 +3.3V 6 XMB_CLK

7 Reserved 8 Reserved

9 Reserved 10 SPI_MISO

11 USB_OC# 12 SPI_MOSI

13 Reserved 14 SPI_CLK

15 +5V 16 SPI_CS10

17 USB_3+ 18 SPI_CS1#

19 USB_3- 20 Reserved

21 +5V 22 LPC_DRQ1#

23 USB_2+ 24 LPC_AD0

25 USB_2- 26 LPC_AD1

27 +5V 28 LPC_AD2

29 USB_1+ 30 LPC_AD3

31 USB_1- 32 LPC_FRAME#

33 +5V 34 SERIRQ#

35 USB_0+ 36 Reserved

37 USB_0- 38 CLK_33MHz

39 GND 40 GND

41 A_PET_P0 42 A_PER_P0

43 A_PET_N0 44 A_PER_N0

45 GND 46 APRSNT#/A_PE_CLKREQ#

47 PERST# 48 A_CLKP

49 WAKE# 50 A_CLKN

51 +5V 52 GND

SUMIT A Pin Out:

GETTING TO KNOW YOUR ECS-9700/ 9600

Pin No. Function Pin No. Function

1 GND 2 GND

3 B_PET_P0 4 B_PER_P0

5 B_PET_N0 6 B_PER_N0

7 GND 8 GND

9 C_CLKP 10 B_CLKP

11 C_CLKN 12 B_CLKN

13 CPRSNT#/C_PE_CLKREQ# 14 GND

15 C_PET_P0 16 C_PER_P0

17 C_PET_N0 18 C_PER_N0

19 GND 20 GND

21 C_PET_P1 22 C_PER_P1

23 C_PET_N1 24 C_PER_N1

25 GND 26 GND

27 C_PET_P2 28 C_PER_P2

29 C_PET_N2 30 C_PER_N2

31 GND 32 GND

33 C_PET_P3 34 C_PER_P3

35 C_PET_N3 36 C_PER_N3

37 GND 38 GND

39 PERST# 40 WAKE#

41 Reserved 42 Reserved

43 +5V 44 Reserved

45 +5V 46 +3.3V

47 +5V 48 +3.3V

49 +5V 50 +3.3V

51 +5V 52 +5V_AUX

SUMIT B Pin Out:

GETTING TO KNOW YOUR ECS-9700/ 9600©Vecow ECS-9700/ 9600 User Manual

2.4.10 Mini PCIe/ mSATA Slot

CN6

CN10

CN12

CN8

SW2

Mini PCIe and mSATA share the same form factor and similar electrical pinout assignments on their connectors. There is no clear mechanism to distinguish if a mSATA drive or a Mini PCIe device is plugged into the socket until recently that SATA I/O issued an ECN change (ECN #045) to redene pin-43 on mSATA connector as “no connect” instead of “return current path” (or GND). When an mSATA drive is inserted, its pin-43 is “no connect”, and the respective pin on the socket is being pulled-up to logic 1. When a Mini PCIe device is inserted, its pin43 forces the respective pin on the socket to ground, or logic 0.

SW2 is for switching mSATA drive and Mini PCIe device.

DIP Switch Interface

SW2-1

Mini PCIe 1

ON Mini PCIe

OFF Auto Detection (Default)

SW2-2

Mini PCIe 2

ON Mini PCIe

OFF Auto Detection (Default)

SW2-3

Mini PCIe 3

ON Mini PCIe

OFF Auto Detection (Default)

SW2-4

Mini PCIe 4

ON Mini PCIe

OFF Auto Detection (Default)

No. Conn. SIM mSATA USB 2.0 Remark

Mini PCIe 1 CN12 SIM1 (CN13) S ATA4 V Mini PCIe 2 CN8 SIM2 (CN9) S ATA5 V Mini PCIe 3 CN10 SIM3 (CN11) S ATA6 V

Mini PCIe 4 CN6 SIM4 (CN7) SATA7 -

Option with SATA4 HDD Connector SIM Only support PCIe module

GETTING TO KNOW YOUR ECS-9700/ 9600

Pin No. function Pin No. function

51 Reserved 52 +3.3Vaux

49 Reserved 50 GND

47 Reserved 48 +1.5V

45 Reserved 46 Reserved

43 GND 44 Reserved

41 +3.3Vaux 42 Reserved

39 +3.3Vaux 40 GND

37 GND 38 USB_D+

35 GND 36 USB_D-

33 PETp0 34 GND

31 PETn0 32 SMB_DATA

29 GND 30 SMB_CLK

27 GND 28 +1.5V

25 PERn0 26 GND

23 PERp0 24 +3.3Vaux

21 GND 22 PERST#

19 Reserved 20 reserved

17 Reserved 18 GND

Mechanical Key

15 GND 16 UIM_VPP

13 REFCLK+ 14 UIM_RESET

11 REFCLK- 12 UIM_CLK

9 GND 10 UIM_DATA

7 CLKREQ# 8 UIM_PWR

5 Reserved 6 1.5V

3 Reserved 4 GND

1 WAKE# 2 3.3Vaux

Pin Out:

GETTING TO KNOW YOUR ECS-9700/ 9600©Vecow ECS-9700/ 9600 User Manual

2.4.11 RTC Battery

The system’s real-time clock is powered by a lithium battery. It is equipped with Panasonic BR2032 190mAh lithium battery. It is recommended that you do not have to get the lithium battery on your own. If the battery needs to be changed, please contact the Vecow RMA service team.

BAT

2.4.12 FAN Header

Fan power connector supports for additional thermal requirements. The pin assignments of FAN 1 are shown in the following diagram:

FN1

Pin No. Function Pin No. Function

1 GND 2 +12V (1.5A max)

3 Fan speed sensor 4 Fan PWM

Pin out:

GETTING TO KNOW YOUR ECS-9700/ 9600

Pin No. Function Pin No. Function

1 SERIRQ 7 LFRAME#

2 +3.3V 8 LAD0

3 LA3 9 N/C

4 RESET# 10 Ground

5 LAD1 11 CLOCK

6 LAD2 12 Ground

Pin out:

2.4.13 LPC Port 80 Header

ECS-9700 provides a LPC Port 80 Header for debug card.

CN3

2.4.14 LAN IEEE 1588 Header

ECS-9700 provides a LAN header for IEEE 1588.

LAN No. Function Function

Front LAN2 Intel I210 J5

Rear POE LAN3 Intel I210 J6

Rear POE LAN4 Intel I210 J7

Rear POE LAN5 Intel I210 J8

Rear POE LAN6 Intel I210 J9

GETTING TO KNOW YOUR ECS-9700/ 9600©Vecow ECS-9700/ 9600 User Manual

J9 J8 J7 J6

JP3

Pin No. Function Pin No. Function

1 SPD0 2 SPD1

3 SPD2 4 SPD3

5 Ground 6 Ground

Pin out:

GETTING TO KNOW YOUR ECS-9700/ 9600

2.4.15 COM Port Header

ECS-9700 provides 4 COM port headers for internal COM port cable.

Pin No. Description Port

1 Ground_Frame COM3

2 Ground COM3

3 RI COM3

4 DTR COM3

5 CTS COM3

6 TXD COM3

7 RTS COM3

8 RXD COM3

9 DSR COM3

10 DCD COM3

CN27:

Pin No. Description Port

1 Ground_Frame COM4

2 Ground COM4

3 RI COM4

4 DTR COM4

5 CTS COM4

6 TXD COM4

7 RTS COM4

8 RXD COM4

9 DSR COM4

10 DCD COM4

CN28:

CN27 CN28

Pin out:

GETTING TO KNOW YOUR ECS-9700/ 9600©Vecow ECS-9700/ 9600 User Manual

2.5 Main Board Jumper & Deep Switch Settings

2.5.1 Top View of ECS-9700 With Jumper and Deep Switch

The gure below is the top view of ECS-9700 board, and it shows the location of the jumpers and the switches.

You may congure your card to match the needs of your application by setting jumpers. A jumper is a metal bridge used to close an electric circuit. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper, please connect the pins with the clip. To “open” a jumper, please remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3. In this case you would connect either pins 1 and 2, or 2 and 3.

FN1

SATA 1

SATA 2

CN27

CN5

CN28

JP2

J9 J8

SATA 3

SATA 4

CN1

SW2

JP7

JP10

JP8

CN2

J10

SW5

JP11

SW7

SW11

CN20

CN3

JP1

JP3

BAT

J11

SUMITB

SUMITA

CFast

CN36

CN9

CN6

CN10

CN12

JP5 JP6

JP9

CN8

CN7

JP4

BZ1

SW3 SW4

GETTING TO KNOW YOUR ECS-9700/ 9600

You may configure your card to match the needs of your application by DIP switch as shown below (the deep switch on and off)

1 2

1 : OFF 2 : OFF

1 2

1 : ON 2 : OFF

1 2

1 : ON 2 : ON

2.5.2 USB Power Jumper

Jumper Setting Function USB Port

JP3 1:2 Non Wake Up support As front plane, blue mark

JP3 2:3 Supported Wake Up (Default) As front plane, blue mark

JP4 1:2 Non Wake Up support As front plane, red mark

JP4 2:3 Supported Wake Up (Default) As front plane, red mark

JP2 1:2 Non Wake Up support As rear plane, green mark

JP2 2:3 Supported Wake Up (Default) As rear plane, green mark

JP2

JP3 JP4

2.5.3 COM Port RI pin Select

Pin Header Pin No. Description

COM1

JP5

1-2 +5V (1A max.)

3-4 +12V (0.5A max.)

5-6

RI (Default)

Pin Header Pin No. Description

COM2

JP6

1-2 +5V (1A max.)

3-4 +12V (0.5A max.)

5-6

RI (Default)

Pin Header Pin No. Description

COM3

JP7

1-2 +5V (1A max.)

3-4 +12V (0.5A max.)

5-6

RI (Default)

Pin Header Pin No. Description

COM4

JP8

1-2 +5V (1A max.)

3-4 +12V (0.5A max.)

5-6

RI (Default)

JP7

JP8

JP5 JP6

GETTING TO KNOW YOUR ECS-9700/ 9600

2.5.4 COM Port RS-422/RS-485 Receiver Terminator

SW3 SW4

COM / DIP Switch ON / OFF

COM RS-422/485

Receiver Terminator

COM1 / SW3-1

ON *Enable

OFF Disable

COM / DIP Switch ON / OFF

COM RS-422/485

Receiver Terminator

COM2 / SW3-2

ON *Enable

OFF Disable

COM / DIP Switch ON / OFF

COM RS-422/485

Receiver Terminator

COM3 / SW4-1

ON *Enable

OFF Disable

COM / DIP Switch ON / OFF

COM RS-422/485

Receiver Terminator

COM4 / SW4-2

ON *Enable

OFF Disable

2.5.5 POE Power ON Select

Jumper Setting Function

JP9 1:2 POE power on at standby power ready

JP9 2:3 POE power on after system power on (Default)

JP9

2.5.6 CMOS & ME Clear

Function

DIP Switch

Description

SW 1-1

CMOS Clear Setting

ON Clear CMOS

OFF *Normal

Function

DIP Switch

Description

SW 1-2

ME Clear Setting

ON Clear ME

OFF *Normal

SW11

GETTING TO KNOW YOUR ECS-9700/ 9600

2.6 Ignition Control

2.6.1 Adjust Ignition Control Modes

ECS-9700 series provides ignition power control feature for in-vehicle applications. The built-in MCU monitors the ignition signal and turns on/off the system according to pre-dened on/off delay periods.

ECS-9700 series provides 16 modes of different power on/ off delay periods adjustable via SW5 switch. The default rotary switch is set to 0 in ATX/ AT power mode.

SW5

The modes are listed in the following table:

Item Power on delay Power off delay Switch Position

0 ATX mode

1 No delay No delay

2 No delay 5 seconds

3 No delay 10 seconds

4 No delay 20 seconds

5 5 seconds 30 seconds

6 5 seconds 60 seconds

7 5 seconds 90 seconds

8 5 seconds 30 minutes

9 5 seconds 1 hour

A 10 seconds 2 hours

B 10 seconds 4 hours

C 10 seconds 6 hours

D 10 seconds 8 hours

E 10 seconds 12 hours

F 10 seconds 24 hours

1 2 3 4

GETTING TO KNOW YOUR ECS-9700/ 9600

2.6.2 Ignition Control Wiring

To activate ignition control, you need to provide IGN signal via the 3-pin pluggable terminal block located in the back panel. It is below the general wiring conguration.

For testing purpose, you can refer to the picture above to simulate ignition signal input controlled by a latching switch.

Note:

1. DC power source and IGN share the same ground.

2. ECS-9700/9600 supports 6V~36V wide range DC power input in ATX/AT

mode. In Ignition mode, the input voltage is xed to 12V/24V for car battery scenario.

3. For proper ignition control, the power button setting should be “Power down”

mode.

In Windows, for example, you need to set “When I press the power button” to "Shut down."

Pin No. Denition

1 Ignition (IGN)

2 External Power S/W +

3 External Power S/W +

IGN

V+

SYSTEM SETUP

3.1 How to Open Your ECS-9700/9600

Step 1

Remove hole plugs.

Step 2

Remove two F#6-32 screws (circled in red) and two F-M3 screws (circled in yellow) on the bottom side.

HARDWARE INSTALLATION

Step 3

Finish Step1 and 2.

Step 4

Remove one KHS#6-32x6 screws(red) and cover(yellow).

Step 6

Finish.

Step 5

Open the module.

HARDWARE INSTALLATION

3.2 Installing DDR4 SO-DIMM Modules

Step 1 DDR4 RAM module into SO-DIMM slot.

Step 2 Make sure the RAM module is locked by the memory slot.

3.3 Installing Mini PCIe Card

Step 1 Install Mini PCIe card into the Mini PCIe socket.

Step 2 Fasten one M2.5 screw.

HARDWARE INSTALLATION

3.4 Installing CFast Card

Step 1 Remove 2 pcs F-M3x4 screws on CFast & SIM Card.

Step 2

Before Inserting CFast & SIM Card, make sure ECS-9700 power is not plugged.

Step 3 Insert CFast card and push to lock.

Step 4 Insert CF card and push to lock.

3.5 Installing SIM Card

Step 1 Remove 2 pcs F-M3x4 screws on CFast & SIM Card.

Step 2

Before Inserting CFast & SIM Card, make sure ECS-9700 power is not plugged.

Step 3 Insert CFast card and push to lock.

Step 4 Insert SIM card and push to lock.

HARDWARE INSTALLATION

3.6 Installing PCI/ PCIe Card

Step 2 Remove the bracket.

Step 1 Remove the M3 screw.

Step 4 Fasten M3 screw.

Step 3 Installing PCI/PCIe card.

HARDWARE INSTALLATION

3.7 Installing SSD/ HDD

Step 1 Trigger and open SSD/HDD tray.

Step 2 Insert 2.5” SSD/HDD in the tray and fasten two F-M3x4 screws.

Step 3 Finish.

Step 4 Installing SSD/HDD.

HARDWARE INSTALLATION

3.8 Mounting Your ECS-9700/9600

Step 1 Ensure the screw holes on the right and left side of the upper case match the ones on ECS-9700/9600 wall mount bracket.

3.8.1 Wall Mount Bracket

Step 2 Fasten 4pcs KHS#6-32 screws then nish.

HARDWARE INSTALLATION

3.8.2 VESA Mount

Step 1 ECS-9700/9600 and VESA Mount.

Step 2

Take ECS-9700/9600 and VESA Mount with fasten 4pcs KHS#6-32 screws.

Step 3 Fasten four KHS#6-32 screws and then nish.

Step 4 Finish.

Step 5 VESA size have 75x75mm(red) and 100x100mm(yellow).

HARDWARE INSTALLATION

3.8.3 Din Rail Kit

Step 1 ECS-9700/9600 and Din Rail Kit.

Step 2 Take ECS-9700/9600 and Din Rail Kit and fasten four KHS#6-32

screws in the four marked corners.

Step 3 Fasten four KHS#6-32 screws and then nish.

Step 4 Finish.

Step 5 ECS-9700/9600 With Din Rail.

BIOS AND DRIVER SETTING

BIOS SETUP

4.1 Entering BIOS SETUP

BIOS provides an interface for users to check and change system conguration. The BIOS setup program is accessed by pressing the <Del> key when POST display output is shown.

Figure 4-1: Entering Setup Screen

4.2 Main

The main menu displays BIOS version and system information. There are two options on Main menu.

System Date

Set the date. Use <Tab> to switch between date elements.

System Time

Set the time. Use <Tab> to switch between time elements.

Figure 4-2: BIOS Main Menu

4.3 Advanced

Figure 4 3: BIOS Advanced Menu

Select advanced tab to enter advanced BIOS setup options, such as CPU conguration, SATA conguration, and USB conguration.

BIOS AND DRIVER SETTING

4.3.1 Trusted Computing

Control the TPM device status and display related information if TPM chip is present.

Figure 4 3-1: Trusted Computing

4.3.2 ACPI Settings

Enable Hibernation

Enables or disables system's ability to hibernate (OS/S4 sleep state). This option may not be effective with some OS.

ACPI Sleep State

Selects the highest ACPI sleep state the system will enter when the SUSPEND button is pressed.

S3 Video Repost

Enables or disables S3 video repost.

ACPI Low Power S0 Idle

Enables or disables ACPI low power S0 idle support.

Figure 4 3-2: ACPI Settings

4.3.4 PCH-FW Conguration

ME Uncong on RTC Clear State

Disabling this option will cause ME not to uncongure on RTC clear.

ME State

Set ME to Soft temporarily disabled.

Figure 4 3-4: PCH-FW Settings

4.3.5 SMART Settings

SMART Self Test

Run SMART self test on all HDDs during POST.

Figure 4 3-5: SMART Settings

4.3.3 AMT Conguration

Intel AMT

Enables/disables Intel (R) Active Management Technology BIOS extension. Note: iAMT H/W is always enabled. This option just controls the BIOS extension execution. If enabled, this requires additional rmware in the SPI device.

Figure 4 3-3: Intel AMT Settings

BIOS AND DRIVER SETTING

4.3.6 IT8786 Super IO Conguration

Figure 4-3-6-1: Super IO Settings

Set the direction of the GPIO pins

Creates bios options for end user to change internal GPIO pin direction.

Figure 4 3-6-3: GPIO Pin Input/Output Settings of SIO IT8786

Figure 4-3-6-2: Serial Port Settings

Serial Port 1 to port 4 Conguration

Options for Serial Port 1 to Serial Port 4. Entering the corresponding Port option then end user can change the settings such as I/O resource and UART mode.

4.3.8 Serial Port Console Redirection

Console Redirection

Console redirection enable or disable.

Console Redirection Settings

These settings specify how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings.

Figure 4 3-8: Serial Port Console Redirection Settings

4.3.7 Hardware Monitor

The IT8786 SIO features an enhanced hardware monitor providing thermal, fan speed, and system voltages' status monitoring.

Figure 4 3-7: Hardware Monitor Settings

BIOS AND DRIVER SETTING

Hyper-threading

Enabled for Windows XP and Linux (OS optimized for Hyper-Threading Technology) and disabled for other OS (OS not optimized for Hyper-Threading Technology). When disabled only one thread per core is enabled.

Active Processor Cores

Number of cores to enable in each processor package.

Intel Virtualization Technology

When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology.

Hardware Prefetcher

To turn on/off the MLC streamer prefetcher.

Adjacent Cache Line Prefetch

To turn on/off prefetching of adjacent cache lines.

CPU AES

Enable/disable CPU Advanced Encryption Standard instructions.

Boot performance mode

Select the performance state that the BIOS will set before OS handoff.

Intel(R) SpeedStep(tm)

Allows more than two frequency ranges to be supported.

Turbo Mode

Turbo Mode.

4.3.9 CPU Conguration

Figure 4 3-9: CPU Function Settings

4.3.10 Intel TXT Information

Display Intel TXT information.

Figure 4 3-10: Intel TXT Information

4.3.11 SATA Conguration

Figure 4 3-11: SATA Devices Settings

CPU C state

Enable or disable CPU C states.

Enhanced C-states

Enable/disable C1E. When enabled, CPU will switch to minimum speed when all cores enter C-State.

Package C State limit

Package C State limit.

Intel TXT(LT) Support

Enables or disables Intel (R) TXT (LT) support.

BIOS AND DRIVER SETTING

SATA Controller(s)

Enable or disable SATA Device.

SATA Mode Selection

Determines how SATA controller(s) operate.

Software Feature Mask Conguration

RAID OROM/RST driver will refer to the SWFM configuration to enable or disable the storage features.

Aggressive LPM Support

Enable PCH to aggressively enter link power state.

SATA Controller Speed

Indicates the maximum speed the SATA controller can support.

Options for each SATA port:

Port 0 Enable or disable SATA Port.

Spin Up Device

On an edge detect from 0 to 1, the PCH starts a COMRESET initialization sequence to the device.

SATA Device Type

Identies that the SATA port is connected to solid state drive or hard disk drive.

4.3.12 Acoustic Management Conguration

Acoustic Management Conguration Option to enable or disable automatic acoustic management.

Figure 4 3-12: Acoustic Management Settings

4.3.13 CSM Conguration

CSM Support

Enable/disable CSM support

GateA20 Active

UPON REQUEST - GA20 can be disabled using BIOS services. ALWAYS - do not allow GA20 to be disabled; this option is useful when any RT code is executed above 1MB.

Option ROM Messages

Set display mode for Option ROM.

INT19 Trap Response

BIOS reaction on INT19 trapping by Option ROM: IMMEDIATE - execute the trap right away; POSTPONED - execute the trap during legacy boot.

Boot option lter

This option controls Legacy/UEFI ROM's priority.

Network

Controls the execution of UEFI and Legacy PXE OpROM.

Storage

Controls the execution of UEFI and Legacy Storage OpROM.

Video

Allows more than two frequency ranges to be supported.

Other PCI devices

Determines OpROM execution policy for devices other than network, storage, or video.

Figure 4 3-13: CSM Settings

BIOS AND DRIVER SETTING

4.3.14 USB Conguration

Legacy USB Support

Enables Legacy USB support. AUTO option disables Legacy support if no USB devices are connected. DISABLE option will keep USB devices available only for EFI applications.

XHCI Hand-off

This is a workaround for OS-es without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver.

USB Mass Storage Driver Support

Enable/disable USB mass storage driver support.

Port 60/64 Emulation

Enables I/O port 60h/64h emulation support. This should be enabled for the complete USB keyboard legacy support for non-USB aware OS-es.

USB transfer time-out

The time-out value for control, bulk, and interrupt transfers.

Device reset time-out

USB mass storage device start unit command time-out.

Device power-up delay

Maximum time the device will take before it properly reports itself to the Host Controller. 'Auto' uses default value, for a root port it is 100 ms, for a hub port the delay is taken from the hub descriptor.

Figure 4 3-14: USB Settings

VT-d

VT-d capability.

GMM Device (B0:D8:F0)

Enable/disable SA GMM device.

Above 4GB MMIO BIOS assignment

Enable/disable above 4GB MemoryMappedIO BIOS assignment. This is disabled automatically when aperture size is set to 2048MB.

4.4.1 System Agent (SA) Conguration

Figure 4-4-1: System Agent Settings

4.4 Chipset

Figure 4-4: BIOS Chipset Menu

System Agent (SA) Conguration

System Agent (SA) parameters.

PCH-IO Conguration

PCH parameters.

BIOS AND DRIVER SETTING

4.4.2 Graphics Conguration of System Agent (SA)

Graphics Turbo IMON Current

Graphics turbo IMON current values supported (14-31).

Skip Scaning of External Gfx Card

If Enable, it will not scan for External Gfx Card on PEG and PCH PCIE Ports.

Primary Display

Select which of IGFX/PEG/PCI Graphics device should be Primary Display Or select SG for Switchable Gfx.

GTT Size

Select the GTT Size.

Aperture Size

Select the Aperture Size. Note: Above 4GB MMIO BIOS assignment is automatically enabled when selecting 2048MB aperture. To use this feature, please disable CSM Support.

DVMT Pre-Allocated

Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics Device.

DVMT Total Gfx Mem

Select DVMT5.0 Total Graphic Memory size used by the Internal Graphics Device.

Cd Clock Frequency

Select the highest Cd Clock frequency supported by the platform.

Figure 4-4-2: Graphics Settings

4.4.3 PEG Port Conguration (SA)

PEG port options for PCIe device.

Figure 4-4-3: PEG Port Conguration

4.4.4 Memory Information of System Agent (SA)

Displays memory information.

Figure 4-4-4: Memory Information

4.4.5 PCH-IO Conguration

Figure 4-4-5: PCH-IO Settings

BIOS AND DRIVER SETTING

PCH LAN Controller

Enable or disable onboard NIC.

Wake on LAN

Enable or disable integrated LAN to wake the system. (The wake On LAN cannot be disabled if ME is on at Sx state.)

Serial IRQ Mode

Congure serial IRQ mode.

State After G3

Specify what state to go to when power is re-applied after a power failure (G3 state). S0 State: Always turn-on the system when power source plugged-in. S5 State: Always turn-off the system when power source plugged-in.

4.4.6 PCI Express Conguration of PCH-IO

Figure 4-4-6: PCH-IO Settings

DMI Link ASPM Control

Enable/Disable the control of Active State Power Management on SA side of the DMI Link.

SUMIT B x 1

Enable or disable PCIe device on SUMIT B.

Front-I210-LAN2

Enable or disable I210 LAN.

Rear-I210-LAN3 to LAN6

Enable or disable I210 LAN.

SUMIT A x 1

Bios options for PCIe device on SUMIT A.

Mini PCIe Slot 1 to 4

Bios options for PCIe devices on miniPCIe Slot.

4.4.7 BIOS Security Conguration of PCH-IO

BIOS Lock

Enable/disable the PCH BIOS Lock Enable (BLE bit) feature.

Figure 4-4-7: BIOS Security Settings

4.4.8 SB Porting Conguration of PCH-IO

SATA RAID ROM

Legacy ROM: Legacy option ROM UEFI Driver: UEFI Raid Driver Both: Run the Legacy Option ROM and UEFI driver.

Figure 4-4-8: RAID ROM Settings

BIOS AND DRIVER SETTING

Set User Password

Set HDD user password. *** Advisable to power cycle system after setting hard disk passwords *** Discard or save changes option in setup does not have any impact on HDD when password is set or removed. If the 'Set HDD User Password' option is gray, do power cycle to enable the option again.

4.5.1 HDD Security Conguration

Figure 4-5-1: HDD Security Settings

4.5 Security

Figure 4-5: BIOS Security Menu

Administrator Password

Set administrator password.

User Password

Set user password.

4.6 Boot

Figure 4-6: BIOS Boot Menu

Setup Prompt Timeout

Number of seconds to wait for setup activation key. 65535(0xFFFF) means indenite waiting.

Bootup NumLock State

Select the keyboard NumLock state.

Quiet Boot

Enables or disables Quiet Boot option.

Boot Option

Sets the system boot order.

New Boot Option Policy

Controls the placement of newly detected UEFI boot options.

Hard Drive BBS Priorities

Set the order of the Legacy devices in this group.

BIOS AND DRIVER SETTING

4.7 Save & Exit

Figure 4-7: Bios Save and Exit Menu

Save Changes and Exit

Exit system setup after saving the changes.

Discard Changes and Exit

Exit system setup without saving any changes.

Save Changes and Reset

Reset the system after saving the changes.

Discard Changes and Reset

Reset system setup without saving any changes.

Save Changes

Save changes done so far to any of the setup options.

Discard Changes

Discard changes done so far to any of the setup options.

Default Options:

Restore Defaults

Restore/load default values for all the setup options.

Save as User Defaults

Save the changes done so far as user defaults.

Restore User Defaults

Restore the user defaults to all the setup options.

Appendix A

A.1 I/O Pin Denition

GPIO Pin Base Address Usage

10, 13, 14, 17

0xA00

-----------

11, 12, 15, 16 CN16-GPIO

20 ~ 27 0xA01 -----------

30, 31, 34

0xA02

-----------

32, 33, 35 ~ 37 CN16-GPIO

40 ~ 47 0xA03 -----------

50 ~ 52, 56, 57

0xA04

CN16-GPIO

53, 54 -----------

60 ~ 63, 66, 67

0xA05

-----------

64, 65 CN16-GPIO

70 ~ 77 0xA06 DO

80 ~ 87 0xA07 DI

APPENDIX A : Isolated DIO Guide

Appendix A

Pin No.

Denition Description

No.

Denition Description

1 EXT_IN0 DI0 11 EXT_OUT0 DO0

2 EXT_IN1 DI1 12 EXT_OUT1 DO1

3 EXT_IN2 DI2 13 EXT_OUT2 DO2

4 EXT_IN3 DI3 14 EXT_OUT3 DO3

5 EXT_IN4 DI4 15 EXT_OUT4 DO4

6 EXT_IN5 DI5 16 EXT_OUT5 DO5

7 EXT_IN6 DI6 17 EXT_OUT6 DO6

8 EXT_IN7 DI7 18 EXT_OUT7 DO7

9 DI_COM DI COM 19 Reserved NC

10 EGND DIO GND 20 E24V External 24V DC

A.2 Function Description

The ECS-9700 offers two 16-bit DIO (8-DI/ 8-DO) 20-pin terminal block connector. Each bit of DI and DO equipped with a photo-coupler for isolated protection. All IO pins are xed by Hardware design and cannot change in/out direction in runtime process. The denition is listed as follows:

Appendix A

A.3 DIO Signal Circuit

DI reference circuit:

Sink Mode (NPN)

V+

V-

Power Supply

6-48V DC

DI_COM (Pin 9)

DI (Pin1-8)

DIO Connector

Source Mode (PNP)

V+

V-

Power Supply

6-48V DC

DI_COM (Pin 9)

DI (Pin1-8)

DIO Connector

DO reference circuit:

V+

V-

Device

6-48V DC

DIO_VDC (Pin 20)

DO (Pin11-18)

DIO_GND (Pin10,19)

DIO Connector

Source Mode (PNP)

Sink Mode (NPN, Default)

V+

V-

Device

6-48V DC

DIO_VDC (Pin 20)

DO (Pin11-18)

DIO_GND (Pin10,19)

DIO Connector

Appendix A

A.4 Software Package contain

There are two folders with the following inside:

● Driver folder includes x32 & x64 versions

● Runtime folder includes DLL and header le for software developer or system integration

● Sample folder includes sample program

A.5 Driver Install

In Driver folder, you can nd the les below inside. Please right click the batch file that is chosen by your OS version, and run as administrator.

Please press any key to install the Framework installation.

Appendix A

On Device Manager, “VECOW Embedded IO Access” will be added.

Please press any key to restart.

Appendix A

A.6 DIO Demo Tool

Execute DIO demo tool (ECS9K7.exe).

Operation on DIO demo tool utility.

Operation on DIO / WDT / PoE Demo tool utility. Click “Read” Button to get value; Input any number in Write and Write Mask textbox, and click “Write” Button to set value. On DIO Panel, Check the DO circuit for “NPN” / “PNP” mode. On PoE Panel, Click “R” to disable PoE switch function (to auto disconnect mode); Click “W” to enable PoE switch function (to manual setting mode).

Vecow ECS-9700, ECS-9600, ECS-9755, ECS-9755-820Q, ECS-9755-505M User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual