Vecima Networks E3K6 User Manual
EUM3006 Integrated
Outdoor Modem
Installation Guide
APCD-LM048-1.3
Copyright
© 2006 by WaveRider Communications Inc. You may
copy and/or print as many copies of this manual as
you wish, as long as the software license agreement
and this copyright statement are included.
Release 1.3, May 2006
The following are trademarks or registered trademarks of their respective companies or organizations:
Windows XP/Microsoft
Windows 2000/Microsoft
:
APCD-LM048-1.3 ii
Software License Agreement
This is a legal agreement between you (either an individual or an entity) and WaveRider Communications Inc. for the use of WaveRider computer software, hereinafter the “LICENSED SOFTWARE”.
By using the LICENSED SOFTWARE installed in this product, you acknowledge that you have
read this license agreement, understand it, and agree to be bound by its terms. You further
agree that it is the full and complete agreement between you and WaveRider Communications
Inc., superseding all prior written or verbal agreements of any kind related to the LICENSED
SOFTWARE. If you do not understand or do not agree to the terms of this agreement, you will
cease using the LICENSED SOFTWARE immediately.
1. GRANT OF LICENSE—This License Agreement permits you to use one copy of the LICENSED
SOFTWARE.
2. COPYRIGHT—The LICENSED SOFTWARE is owned by WaveRider Communications Inc. and is
protected by copyright laws and international treaty provisions; therefore, you must treat the
LICENSED SOFTWARE like any other copyrighted material (e.g., a book or magazine).
3. LIMITS OF FEATURE AVAILABILITY—The LICENSED SOFTWARE is sold with limitations as
to certain feature availability and use. These limits are governed by the terms of the purchase
agreement. Any actions resulting in the exceeding of these limits is not permitted, and can result
in unpredictable performance.
4. OTHER RESTRICTIONS—You may not rent or lease the LICENSED SOFTWARE. You
may not reverse engineer, decompile, or disassemble the LICENSED SOFTWARE.
5. LIMITED WARRANTY—The LICENSED SOFTWARE is provided “as is” without any warranty of
any kind, either expressed or implied, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. The entire risk as to the quality and
performance of the LICENSED SOFTWARE is with you, the licensee. If the LICENSED
SOFTWARE is defective, you assume the risk and liability for the entire cost of all necessary
repair, service, or correction.
Some states/jurisdictions do not allow the exclusion of implied warranties, so the
above exclusion may not apply to you. This warranty gives you specific legal
rights, and you may have other rights, which vary from state/jurisdiction to state/
jurisdiction.
WaveRider Communications Inc. does not warrant that the functions contained in
the LICENSED SOFTWARE will meet your requirements, or that the operation of
the LICENSED SOFTWARE will be error-free or uninterrupted.
6. NO OTHER WARRANTIES—To the maximum extent permitted by applicable law, WaveRider
Communications Inc. disclaims all other warranties, either express or implied, including, but not
limited to, the implied warranties of merchantability and fitness for a particular purpose, with
regard to the LICENSED SOFTWARE and the accompanying written materials.
7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES—To the maximum extent permitted by
applicable law, in no event shall WaveRider Communications Inc. or its suppliers be liable
for any damages whatsoever (including, without limitation, damages for loss of business
profits, business interruption, loss of business information, or any other pecuniary loss)
arising from the use of or inability to use the LICENSED SOFTWARE, even if WaveRider
Communications Inc. has been advised of the possibility of such damages, or for any claim
by any other party.
Because some states/jurisdictions do not allow the exclusion or limitation of liability for
consequential or incidental damages, the above limitation may not apply to you. In no event will
WaveRider’s liability exceed the amount paid for the LICENSED SOFTWARE.
iii APCD-LM048-1.3
Warranty
In the following warranty text, “WaveRider®” shall mean WaveRider Communications Inc.
This WaveRider product is warranted against defects in material and workmanship for a period
of one (1) year from the date of purchase. During this warranty period WaveRider will, at its
option, either repair or replace products that prove to be defective.
For warranty service or repair, the product must be returned to a service facility designated by
WaveRider. Authorization to return products must be obtained prior to shipment. The WaveRider RMA number must be on the shipping documentation so that the service facility will accept
the product. The buyer shall pay all shipping charges to WaveRider and WaveRider shall pay
shipping charges to return the product to the buyer within Canada or the USA. For all other
countries, the buyer shall pay shipping charges as well as duties and taxes incurred in shipping
products to or from WaveRider.
WaveRider warrants that the firmware designed by it for use with the unit will execute its programming instructions when properly installed on the unit. WaveRider does not warrant that the
operation of the unit or firmware will be uninterrupted or error-free.
Limitation of Warranty
The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by the buyer, buyer-supplied interfacing, unauthorized modification or misuse, operation
outside the environmental specifications for the product, or improper site preparation or maintenance. No other warranty is expressed or implied. WaveRider specifically disclaims the implied
warranties of merchantability and fitness for any particular purpose.
:
No Liability for Consequential Damages
To the maximum extent permitted by applicable law, in no event shall WaveRider or its suppliers
be liable for any damages whatsoever (including, without limitation, damages for loss of business profits, business interruption, loss of business information, or any other pecuniary loss)
arising from the use of or inability to use the product, even if WaveRider has been advised of the
possibility of such damages, or for any claim by any other party.
Because some states/jurisdictions do not allow the exclusion or limitation of liability for consequential or incidental damages, the above limitation may not apply to you.
In no event will WaveRider’s liability exceed the amount paid for the product.
Regulatory Notices
This equipment has been tested and found to comply with the limits for a Class B Intentional
Radiator, pursuant to Part 15 of the FCC Regulations. These limits are intended to provide protection against harmful interference when the equipment is operated in a residential environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation.
Notice to User
Any changes or modifications to equipment that are not expressly approved by WaveRider may
void the user’s authority to operate the equipment.
APCD-LM048-1.3 iv
v APCD-LM048-1.3
Contents
Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii
Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Document Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 EUM3006 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.3 EUM3006 - End-user Modem or Customer Premises Equipment . . . . . . . . . . . . . . . . 5
1.3.1 Key Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.3.2 EUM3006 Integrated, High Gain, Active Diversity Antenna . . . . . . . . . . . . . . . 5
1.3.3 Ethernet Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.3.4 Power over Ethernet (PoE) Injector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.3.5 PoE Lightning Arrestor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.4 Installation Aids. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
:
2 MDB1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1 Placing the MDB1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.2 Powering the MDB1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.3 Turning the MDB1000 On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.4 Turning the MDB1000 Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.5 Interpreting the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3 Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.1 Accessing the Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2 Setup Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.3 Radio Link Status Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.4 Troubleshooting Information Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.1 Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.2 Pre-Installation Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.2.1 Network and EUM3006 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.2.2 Installer’s Kit and Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.2.3 Verifying the EUM3006 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.2.4 End-Users PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.3 Installation Steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.3.1 Locating the EUM3006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.3.2 Mounting the EUM3006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.3.3 Running Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.3.4 Provide Power to the EUM3006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.3.5 Connecting the End-User’s PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.3.6 Testing the Data Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4.4 Post-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
APCD-LM048-1.3 vi
Appendix A Factory Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Appendix B Ethernet Cables and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
vii APCD-LM048-1.3
Figures
Figure 1 Grounding EUM3006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xvii
Figure 1 EUM3006 Integrated Outdoor Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Figure 2 EUM3006 Longitudinal and Transverse Axes . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 3 PoE Injector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 4 MDB1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 5 EUM3006 Mounting - Vertical Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 6 EUM3006 Mounting - Horizontal Orientation . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 7 PoE Injector - Data & PWR and Data Ports . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 8 T568A Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 9 T568B Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
:
APCD-LM048-1.3 viii
ix APCD-LM048-1.3
Tables
Table 1 MDB1000 Signal Strength FOMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table 2 MDB1000 Signal Quality LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Table 3 Pre-Installation Stage Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 4 Installation Stage Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 5 Ethernet Interface Card LED Status Displays . . . . . . . . . . . . . . . . . . . . . . . 31
Table 6 Ethernet Interface Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Table 7 Wiring T568A and T568B ends for Ethernet Cables . . . . . . . . . . . . . . . . . . 40
:
APCD-LM048-1.3 x
xi APCD-LM048-1.3
Preface
Conventions
The following conventions are used throughout this document:
:
WARNING!
Whenever you see this icon and heading, the associated text
addresses or discusses a critical safety or regulatory issue.
CAUTION: Whenever you see this icon and heading, the
associated text discusses an issue, which, if not followed, could
result in damage to, or improper use of, the equipment or
software.
TIP: Whenever you see this icon and heading, the associated
text provides a tip for facilitating the installation, testing, or
operation of the equipment or software.
Regulatory Notices
This device has been designed to operate with its integrated antenna only. This device has
been tested using unshielded Ethernet CAT-5E cable.
Industry Canada
Operators must be familiar with IC RSS-210 and RSS-102. The EUM3006 has been
designed and manufactured to comply with IC RSS-210 and RSS-102.
Federal Communications Commission
The EUM3006 has been designed and manufactured to comply with FCC Part 15.
Operators must be familiar with the requirements of the FCC Part 15 Regulations prior
to operating any link using this equipment. For installations outside the United States,
contact local authorities for applicable regulations.
The transmitter of this device complies with Part 15.247 of the FCC Rules.
APCD-LM048-1.3 xii
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• --Reorient or relocate the receiving antenna.
• --Increase the separation between the equipment and receiver.
• --Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• --Consult the dealer or an experienced radio/TV technician for help.
Interference Environment
Operation is subject to the following conditions:
• This device may not cause harmful interference and,
• This device must accept any interference received, including interference that
might cause undesired operation.
Operational Requirements
In accordance with the FCC Part 15 regulations:
1. The maximum average power output of the intentional radiator shall not
exceed one (1) watt (30 dBm) for all spread spectrum systems operating in
the 902 to 928MHz band.
2. Stations operating in the 902 to 928MHz band may use transmitting antennas
of directional gain greater than 6dBi, provided the average output power from
the intentional radiator is reduced by the amount in dB that the directional gain
of the antenna exceeds 6dBi.
3. The operator of a spread spectrum system and the user of the radio device
are each responsible for ensuring that the system is operated in the manner
outlined in Interference Environment on page xiii.
The EUM3006 with its integrated antenna complies with these requirements.
xiii APCD-LM048-1.3
Warnings and Advisories
General Advisory
Installers, operators and maintenance personnel must be familiar with the related safety
requirements before they attempt to install or operate the EUM3006.
It is the responsibility of the operator to ensure that the public is not exposed to excessive
Radio Frequency (RF) levels. The applicable regulations can be obtained from local
authorities.
WARNING!
The EUM3006 Integrated Outdoor Modem must be properly
grounded. WaveRider assumes no liability for failure to
adhere to this recommendation or to recognized general
safety precautions.
:
To comply with FCC RF exposure limits, the EUM3006 must
be fix-mounted outdoors to provide a separation distance of
30cm (1 foot) or more from all persons to satisfy RF exposure
requirements. The distance is measured from the nearest
point of the modem to the human body. It is recommended
that the modem be installed in a location with minimal
pathway disruption by nearby personnel.
Important Safeguards
CAUTION: Do not open the EUM3006, since there are no userserviceable parts inside and opening the EUM3006 will void
its warranty. Refer servicing to qualified personnel.
1. Read all these instructions before installing and operating the EUM3006.
2. Retain these instructions for future reference.
WARNING!
WARNING!
3. Heed all warnings on the EUM3006 and in these instructions.
4. Follow all instructions.
5. Do not use EUM3006 and PoE Injector near water.
6. Unplug EUM3006 and PoE Injector from the wall outlet before cleaning. Clean only
with a damp cloth.
APCD-LM048-1.3 xiv
7. Use only attachments recommended by WaveRider.
8. The fins and metal casing protect the EUM3006 from overheating to ensure reliable
operations. Do not cover the EUM3006 and PoE Injector. Do not place the EUM3006
or PoE Injector near or over a radiator, stove, heat register or other source of heat. Do
not place the EUM3006 and PoE Injector in a built-in installation such as a bookcase
or rack unless proper ventilation is provided. The EUM3006 has an outdoor
temperature rating, so it can handle a much larger range of temperatures than the
PoE injector. However, it is still possible to exceed the EUM3006 specifications by
improper placement or ventilation.
9. Operate the EUM3006 only from a 48 VDC PoE Mode B power source.
10. Operate the PoE Injector only from a 100 - 250 VAC, single phase, 47-63 Hz AC
power source. The PoE Injector is rated for indoor use only.
11. The PoE Injector is equipped with a 3-wire grounding-type plug, which will only fit into
a grounding-type power outlet. This is a safety feature. If you are unable to insert the
plug into the outlet, contact an electrician to replace your obsolete outlet. Do not
defeat the purpose of the grounding-type plug.
12. Route the AC Power-supply cord and Ethernet cables so that they are not likely to be
walked on or pinched by items placed upon or against them, paying particular
attention to cord and cables at their plugs, convenience receptacles and the points
where the cords exit the equipment.
13. Provide strain relief for cables near their connections. This is typically done by leaving
a loop in the cable near the connection.
14. Ensure the system is properly grounded to provide some protection against voltage
surges and built-up static charges.
15. Do not locate the EUM3006 in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall onto such power lines or circuits. When
installing outdoors, take extreme care to keep from touching such power lines or
circuits, as contact with them might be fatal.
16. For added protection during a lightning storm, or when it is left unattended and unused
for long periods of time, unplug the Ethernet cable from the PoE injector to the
EUM3006 and unplug the PoE Injector from the wall outlet. If the Ethernet cable to the
EUM3006 goes through a PoE Lightning Arrestor, then disconnect the inside Ethernet
cable. This will power down the EUM3006.
17. Do not overload wall outlets and extension cords as this increases the risk of fire or
electric shock.
18. Never push objects of any kind through openings in this wireless product as they may
touch dangerous voltage points or short-out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the PoE Injector. The EUM3006 is an outdoor
unit, but it is not submersible nor is it immune to all liquids.
19. Do not attempt to service this wireless product yourself, as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
xv APCD-LM048-1.3
20. Unplug PoE Injector from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled or objects have fallen into these products.
• If the PoE Injector has been exposed to rain or water.
• If the EUM3006 does not operate normally for an extended period of time when
following the operating instructions. Note that it is possible that Internet traffic can
be slow even under normal operations due to network congestion and radio
interference and fading and not as result of problems with the EUM3006.
• When the EUM3006 or PoE Injector exhibit distinct changes in performance. This
may indicate a need for service.
21. When replacement parts are required, be sure the service technician has used
replacement parts specified by the WaveRider or with the same characteristics as the
original part. Improper substitutions may result in fire, electric shock or other hazards.
22. Upon completion of any service or repairs to this wireless product, ask the service
technician to perform safety checks to determine that the wireless product is in proper
operating condition.
23. Follow WaveRider recommendations when mounting the EUM3006 on a wall, roof, or
tower.
:
24. Install the EUM3006 in compliance with local and national electrical codes. The
following are the national codes. The installer is responsible for knowing the
appropriate local codes.
• In the United States, use the National Electrical Code (NEC);
• In Canada, use the Canadian Electrical Code, Part 1, CSA C22.1;
• In other countries, use International Electrotechnical Commission (IEC) 364,
part 1 through 7.
25. Ensure that the EUM3006 is properly grounded by attaching a grounding cable to the
bolt marked “GND” on the back of the EUM3006. Art. 820-40 of the NEC (US)
provides guidelines for proper grounding and, in particular, specifies that the
grounding cable(s) shall be connected to the grounding system of the building, as
close to the point of cable entry as possible.
APCD-LM048-1.3 xvi
Connect Ground
Wire to GND Lug
Ethernet Cable
Grounding Conductor
(NEC Sec. 810-21)
Electrical
Service
Equipment
Ethernet Surge
Protection
Power Service Grounding Electrode System
(NEC Art. 250, Part H)
Figure 1 Grounding EUM3006
xvii APCD-LM048-1.3
Revision History
Date Revision Description
Nov 2004 1.0 Initial Version
Dec. 2004 1.1 Correct Power for FCC
Jan 2005 1.2 Update Power and add Industry Canada
May 2006 1.3 SW Version 11.0 - Security Features
Customer Support
An extensive knowledge base is available at support.waverider.com.
:
WaveRider offers a complete training program. Please contact your sales representative for
training information.
WaveRider also offers priority telephone and email support. Please contact your sales
representative for details.
APCD-LM048-1.3 xviii
xix APCD-LM048-1.3
Loading...