Vdwall LVP615U, ledsync820h, LVP615D User Manual

LVP615U

LED HD Video Processor

User Manual

V1.0

LVP615U

使用说明

Contents

Chapter 1: Safety precautions

-------------------------------------------------- 4

Chapter 2: Item list

-------------------------------------------------------------------- 5

Chapter 3: Hardware connection

3.1 Rear view-------------------- --------------------------------------------------- 6

3.2 Port description----------------------------------------------------------------- 6

3.3 Hardware connection diagram----------------------------------------------- 8

3.4 Specifications---------------------------------------------------------------------9

3.5 Product dimensions------------------------------------------------------------11

Chapter 4: Front panel and remote control instructions

4.1 Front panel buttons and remote control schematic----------------------- 13

4.2 Remote control operation instructions---------------------------------------- 15

Chapter 5: Basic user instructions

5.1 Input signals selection ---------------------------------------------------------- 17

5.2 PIP/PBP operation--------------------------------------------------------------- 21

5.3 Mosaic operation----------------------------------------------------------------- 22

5.4 Other basic user operation----------------------------------------------------- 23

Chapter 6: Setup menu instructions

6.1 Output image setting------------------------------------------------------------ 26

6.2 Input video signal setting------------------------------------------------------- 30

6.3 Text overlay setting-------------------------------------------------------------- 33

6.4 Image quality setting------------------------------------------------------------ 35

6.5 Audio setting----------------------------------------------------------------------- 36

6.6 Communication setting---------------------------------------------------------- 37

6.7 Language setting------------------------------------------------------------------ 38

6.8 Advance setting------------------------------------------------------------------- 49

6.9 PIP/PBP setting-------------------------------------------------------------------- 42

6.10 Mosaic setting------------------------------------------------------------------- 43

LVP615U

使用说明

Chapter 7: Remote control instructions

7.1 Hardware communication-------------------------------------------------- 48

7.1.1 RS232 and USB-------------------------------------------------------------- 49

7.1.2 Wired network---------------------------------------------------------------- 50

7.1.3 WIFI connection--------------------------------------------------------------- 51

7.2 LVP615U series PC control software instructions----------------------

7.2.1 Control method---------------------------------------------------------------- 58

7.2.2 Software interface instructions-------------------------------------------- 59

7.3 APP remote control---------------------------------------------------------- 76

7.3.1 Connection----------------------------------------------------------------------- 77

7.3.2 APP control instructions-------------------------------------------------------80

Chapter 8 Copyright information---------------------------------------------------97

Appendix: modify the record table ----------------------------------------------------- 98

LVP615U

使用说明

Chapter 1: Safety precautions

！Danger

There is high voltage in the processor, to prevent any unexpected hazard, unless you are maintenance, please do not open the cover of the device.

！Warning

1. This device shall not encounter water sprinkle or splash, please do not place anything containing water on this device.

2. To prevent fire, keep this device far from any fire source.

3. If this device gives out any strange noise, smoke or smell, please immediately unplug the power cord from receptacle, and contact local dealer.

4. Signal cables are not hot swappable.

！Caution

1. Please thoroughly read this manual before using this device,

and keep it well for future reference.

2. In the event of lighting or when you are not going to use the

device for a long time, please pull the power plug out of receptacle.

3. Nobody other than professional technicians can operate the

device, unless they have been appropriately trained or under guidance of technicians.

4. To prevent equipment damage or electric shock, please don’t

fill in anything in the vent of the device.

5. Do not place the device near any water source or anywhere damp.

6. Do not place the device near any radiator or anywhere under

high temperature.

7. To prevent rupture or damage of power cords, please handle and

keep them properly.

LVP615U

使用说明

8. Please immediately unplug power cord and have the device repaired, when

1) Liquid splashes to the device.

2) The device is dropped down or cabinet is damaged.

3) Obvious malpractice is found or performance degrades.

Chapter 2 Item List

Please unpack the product carefully, then check whether all the following things are included in the package. If anything is found missing, please contact the dealer.

Standard accessories

The accessories supplied with this LED Video Processor may differ from the figures contained in the User’s Manual, but they are applicable for the regions where you live.(LED sending card is optional)

1.5m power cord*1

1.5m DVI cable*1

0.5m DVI cable*1

1.5m RS232 to RJ45

adapter cable*1

User manual *1

CD*1

Remote control *1

Audio connector *1

BNC-RCA adapter *3

LVP615U

使用说明

Chapter 3 Hardware connection

3.1 Rear view

13524

3.2 Ports description

3.2.1 Video signal inputs (INPUT)

LVP615U supports 8 video signals input as follows:

Port

Description

LVP615U

使用说明

1*Composite Video (PAL/ NTSC)

V2 / YPbPr

1* Composite video (PAL/ NTSC) or analog

component video input

VGA1~VGA2

2 * PC analog signal

DVI

1* DVI ( PC digital signal)

HDMI

1*HDMI (HD digital signal)

1*DisplayPort( digital signal input)

EXT.

1* Extended PAL/NTSC composite video input

3.2.2Audio input signals（AUDIO）

LVP615U supports 5-channel stereo audio inputs switching. Of which, 3channels are DP, HDMI and USB input. The other 2 channels are AD1, AD2 external audio input. AD1 and AD2 can be mapped to any one of signal inputs, and will be switched synchronous to the selection of video input signals.

3.2.3 Video signal output

Port

Description

VGA OUT

1-channel analog RGBHV signal output,

which can be connected to a local display

device for monitoring (it is strongly

recommended to use this port when

operating and setting LVP615U).

DVI OUT1 /

DVI OUT2

2 same DVI digital graphic signal output,

it can be connected to external 2 LED

transmission cards or LED transmission

boxes.

DVI Loop OUT

1-channel computer DVI digital signal

loop output

LVP615U

使用说明

3.2.4 Other ports

Port

Description

LAN

TCP/IP local area network control

interface

USB

USB communication port

RS232 IN

Serial communication interface, used to

connect the RS232 port of PC to realize

PC software control.

RS232 LOOP

Serial communication cascading output

for connecting the RS232 IN of next unit,

through single PC can control several

units.

Antenna interface of wireless control

function

RF 2

Network intelligent module

3.3 Hardware connection diagram

LVP615U

使用说明

3.4 Specifications

LVP615U

使用说明

Inputs

Nums / Type

2×Video

1×YPbPr

2×VGA（RGBHV）

1×DVI（VESA /CEA-861）

1×HDMI（VESA /CEA-861）

1×DP（VESA）

1*EXT ( USB)

Video system

PAL/NTSC

Composite Video

Amplitude Impedance

1V（p_p）/ 75Ω VGA format

PC（VESA standard）

≤2048×1152_60Hz

VGA Amplitude

Impedance

R、G、B = 0.7 V（p_p）/ 75Ω YPbPr format

SD/HD（CEA -861）

≤1920x1080p_60Hz

YPbPr Amplitude

Impedance

Y=1V（p_p）/ 75Ω

Pb= 0.35V（p_p）/ 75Ω

Pr= 0.35V（p_p）/ 75Ω

DVI format

PC（VESA standard）

≤2304×1152_60Hz

Custom output format

Width≤3840 ，

Height≤1920

HDMI format PC（VESA standard）

≤1920×1080_60Hz HDMI1.3（CEA-861）

DP format

Display Port 1.1 （ VESA

standard）

≤1920×1080_60Hz

USB

video format

MKV/TS/M2TS/TP/TRP/AVI

/WMV/RM/RMVB/MPEG/M

PG/MP4/VOB/MOV/ISO/DA

T/ASF

Video encoding format

H.265 AVC HD、VC-1(WMV HD) 、 MPEG-2 HD 、 MPEG-1、MPEG-4、Xvid

LVP615U

使用说明

Picture format

JPG 、 PNG 、 BMP ， max

resolution 15million.

Input connectors

Video：BNC

YPbPr：BNC×3

VGA：15pin D_Sub(female)

DVI：24+1 DVI_D

HDMI：HDMI port A type

DP：Display Port

USB:USB A type

VGA/DVI format

1024×768_60Hz/75Hz

1280×1024_60Hz/75Hz

1600×1200_60Hz

1920×1080p_50Hz/60Hz

1366×768_60Hz

1440×900_60Hz

2048×1152_60Hz

2560×816_60Hz

2304×1152_60Hz

1920×1200_60Hz

1200×1600_60Hz

1080×1920_60Hz

1536×1536_60Hz

Custom output format（maximum horizontal pixel:3840，

maximum vertical height:1920）

Output connectors

VGA OUT:15Pin D-sub( female)

DVI OUT1：24+5 DVI_I

DVI OUT2：24+1 DVI_D

Others

Control

RS232/USB/LAN/WIFI/Remote control

Input voltage

100-240VAC 50/60Hz

Power consumption

≤25W

Environment

Temperature

0-45 ℃ Environment Humidity

15-85%

LVP615U

使用说明

3.5 Product dimensions

Product Size

483(L) x 274(W) x 66.6(H)mm

Weight

G.W.：5.7 Kg, N.W.：4.2Kg

LVP615U

使用说明

RS232 cable order：

LVP615U

使用说明

Chapter 4 Front panel and remote control instructions

LVP615U supports front panel button, remote control, RS232 and LAN control. Same printing on remote control buttons and front panel buttons,same button functions. The instructions are as below.

4.1 Front panel buttons and remote control schematic

124

LVP615U

使用说明

4.1.1Input signal selection buttons

（ , , , , , , , ，）：select the

input signal.

4.1.2 Setup buttons( , ， , , ), Set the output

image parameters.

4.1.3 VGA auto adjustment button ( )automatically adjust the VGA input signal.

4.1.4 Switching time setup button

（）：

select seamless switching

time including 0 second (cut), 0.5 second,1.0 second and 1.5 second

( fade in fade out) and blend switching function.

The buttons on remote control have the same functions as the relative buttons on front panel.

LVP615U

使用说明

4.1.5 PC signal bypass output ( )：Switch between part and full

display of PC signal. The indicator shows the current state of the input

signal.

4.1.6 PIP/PBP keys

（，，，）：

:PIP/PBP turn on/ off button. When the indicator is on, press

input signal selection to choose different group input or current input itself

as the PIP signal.

，， :Switch PIP/PBP model.

4.1.7 Mosaic button

（）

Turn on /off mosaic function. The

indicator shows the current state of mosaic.

4.1.8 Freeze button

（）

turn on / off freeze function.

4.1.9 Brightness adjustment button

（，）

adjust output

brightness level under user operation station.

4.1.10 remote control sensor: built- in infrared receiver.

4.1.11 remote launch window: built-in infrared transmitter.

LVP615U

使用说明

4.2 Remote control operation instructions

4.2.1 Open the battery compartment on the back of the remote control, make sure the battery effective contact

4.2.2 Please aim remote control to the sensor area of LVP615U, if

there is obstacle between them, LVP615U may not receive command.

4.2.3 To make sure remote control has a good performance. If found

improper operation, please replace new battery immediately.

4.3.3 Batteries shall not be exposed to, such as sunlight, fire or

the like overheated environment.

Chapter 5 Basic user instructions

After LVP615U boot, it enters the operation status of last shut-down including signal switching status, PIP/POP (or Text overlay) status and mosaic status. Among them, PIP/PBP( or text overlay) status and mosaic status can only realize relative functions and cannot do other operation. Other relative operations are available under signal switching status. We illustrate the common operations as below.

LVP615U

使用说明

5.1 Input signals selection

LVP615U supports two signal switching methods including“One key

switching”and“Pre.+Take switching”. The switching method can be set in user setup menu “2.6 switch mode”. “One key switch” is default method. One key switch to new input signal through input signal selection buttons.； “Pre.+Take switch” only available for seamless switching. Press input buttons to preselect first. Then press Take button to switch from current input signal to preselected signal.

LVP615U

使用说明

Input signal selection as follows

：

Buttons

Description

1* Composite video signal input (PAL/ NTSC)

1* Composite video (PAL/ NTSC) or analog

component video input

2 * PC analog signal input

1*DVI digital signal input

1 * HDMI digital signal input

1* DisplayPort digital signal input

1* extended signal input

Note：(1) YPbPr and V2 share the same port. If need,configure

the port to YPbPr in setup menu.

5.1.1 One key switch

LCD screen display as below：

LVP615U

使用说明

Input： HDMI In Status： 1080p_60Hz

-------------------------------------Output Size： 1920x1080 Output Start：（0，0）

-------------------------------------Switch Mode： One Key SW. Switch Time： 1.5 Sec

After select input signal, The first line on the LCD display the

current input signal. Like：“ Input：HDMI ” 。The second line on the

LCD display the signal status.If no active input, display” No input’.

Meanwhile,the corresponding indicator flicker. Led screen is black.

If active input, display input signal format Like：“ 1080p_60Hz ”

。

5.1.2 Pre.+Take switch

LCD screen display as below：

LVP615U

使用说明

Curr. Input： HDMI Curr. In Status： 1080p_60Hz Pre. Input： V1 Pre. In Status： PAL

-------------------------------------Output Size： 1920x1080

Output Start：（0，0） Switch Mode： Pre.+Take SW. Switch Time： 1.5 Sec

Switching signal method: press input button to preselect first, LCD screen displays the current input status and preselect input status. Then press Take button to switch current input to preselect input. After the completion of switching, preselect signal become the current input signal. The status of the preselect signal indicator: when the signal is valid, the indicator flicker rapidly. when the signal is invalid, the indicator flicker slowly.

Note：Pre.+Take switch only available for seamless switching. LVP615U

supports seamless switching between any two different input groups as follow.

Same group does not support seamless switching. For example, current input

is V1( V1 in group A). Then, preselect signal is only from B,C,D group. Signal

group as follow.

：

ABC

V1、V2

VGA1、

VGA2

DVI、 HDMI、DP

EXT

5.1.3 Switching time setting（C/ F

）

LVP615U

使用说明

In the signal switching status, press C/F button continually can change the current seamless switching transition time. LVP615U can achieve seamless switching between any two different input groups of four input groups. Switching effect includes seamless switching (0s), Fade in/ Fade out (o.5s 1s

1.5s) and blend switching.

Seamless switching（Cut）：On the LCD“Switch time” is 0s. LVP615U default

switching is CUT.

Fade in fade out（Fade）：On the LCD“Switch time”is 0.5s、1.0s or 1.5s. In this

mode, different group signals support fade in fade out switching.

Blend switching：at this moment, on the LCD, current input is the main input.

Select different group input signal as blend signal. The main input will overlay

in the blend signal. Press blend signal or main signal button again. Then switch

to selected signal. The whole process is fade in fade out effect.

Main Input： HDMI Main In Status： 1080p_60Hz Blend Input： V1 Blend In Status： PAL

-------------------------------------Output size： 1920x1080 Output start：（0，0）

--------------------------------------

Note：1. YPbPr does not support seamless switching, fade in

fade out or blend switching. Switching between any signal and

YPbPr signal will cause black led screen.

2. Blend switching is only for signal switching. For other

operations, press C/F to exit the blend switching state.

LVP615U

使用说明

5.2 PIP/PBP operation

LVP615U allows to insert PIP window on the current display signal.

That is dual image display function(PIP/PBP)。PIP signal can be any

input signal from other input groups or current input signal itself.

（

signal group refer to page 19signal group list）Dual image size can

be preset 3 modes.The detailed operation method is as follow：

Enter PIP/PBP mode： press On/Off button，the indicator will

be on. LVP615U enters PIP/PBP mode. Then press input signal button

to select PIP signal. At the same time, LCD will display main input and

pip input status and size.（as shown below

）

Main Input： HDMI Main In Status： 1080p_60Hz PIP Input： V1 PIP In Status： PAL

-------------------------------------Main Output Size： 1920x1080 Main Output Start：（0，0） PIP Output Size： 640x320 PIP Output Start：（16，16）

Select PIP input signal：In PIP mode，press button to select

corresponding signal. Then this signal is configured as PIP input.

Select Main input signal： Press On/Off button to close PIP

mode.，Press button to select corresponding signal as main input

signal. Then press On/Off button to enter PIP mode to select pip

signal again.

LVP615U

使用说明

Switch PIP/PBP mode：When PIP/PBP is on，press buttons M1、

M2、M3 directly to select display mode fast.

5.3 Mosaic operation

Multiple units LVP615U cascading can drive huge resolution LED screen. Only when the current input is DVI, press Mosaic button and the indicator is on. LVP615U enters to Mosaic operation. Press the button again and the indicator is off, LVP615U exits Mosaic.

Mosaic Input： DVI In Status： 1080p_60Hz Input Image Size： 960x540 Input Image Start：（0，0）

-------------------------------------Mosaic out size： 1920x1080 Mosaic out start：（0，0） Mosaic PIP: off

-------------------------------------Device ID: 1

Note：

5.3.1 In mosaic mode, PIP display is available.

5.3.2 In following conditions ， LVP615U cannot enter mosaic

status.

（1）The input signal selected is not DVI；（2）

Bypass is on

；

（3）The resolution of DVI input signal is different from the

output resolution of processor.

LVP615U

使用说明

5.4 Other basic user operation

5.4.1 Brightness selection（Brt+，Brt-）

LVP615U supports 64 level or 100 level brightness selection.

According to“8.5 bright level” selection，adjustment range has two kinds：0~64 or 0-100. Factory default is 0-64。To make sure of full

gray scale of output image, it always set as 64（0-100 default value is 50）！

button

description

BRT-

Reduce LVP615U output brightness，the lowest

is 0.

BRT+

Increase LVP615U output brightness, the

highest is 64 or 100.

5.4.2 VGA input auto adjustment (Auto)

When LVP615U is in one key switch status and current valid

input signal is VGA, press Auto button to adjust VGA input signal

sampling parameters. Then the VGA output image can be clear and

full.

This operation is normally performed when a new VGA source

is connected. Auto adjustment time is depend on the signal status.

LVP615U

使用说明

Normally it’s less than 1 second. Sometimes it’s necessary to

perform several times until the output image is clear, full and stable.

5.4.3 Full/ part display（Bypass）

In signal switching status, press Bypass button to switch full

and part display.

This function only works when current signal is PC input signal

（VGA1/ VGA2/ DVI /HDMI /DP). Fixed other signals to Full mode.

state

description

Full

Full display,the input image is compressed and fully

displayed on the led screen and the indicator is off.

Part

Part display, the input image is not compressed.Only a

part of it can be displayed on the screen and the indicator

is on.

Note:When the width and height of input image are lower than the

LED screen real width or height value. Part display is invalid.

5.4.4 Text overlay

LVP615U allows for overlapping text, logo or flash on the current

image. The operation is as below.

When the current input display properly, enter setup

menu“3.Text overlay” ， set ”3.1text overlay” on ， then select text

source.Text can be produced by PowerPoint and other office software.

LVP615U

使用说明

5.4.5 Image freeze (Freeze)

Press Freeze button and the indicator is on, the current image is

frozen. Press Freeze button again or switch to another signal to exit

Freeze status.

5.4.6 Device information view (OK)

In signal switching status, press OK to check the LVP615U current

setting and information.

System info

-------------------------------------model： LVP615U version： V0.0.8/V0.0.8 IP： 192.168.1.8 Mask： 255.255.255.0 Gate： 192.168.1.1 MAC： 76-64-77-00-00-00 Device ID: 1

Chapter 6: Setup menu instructions

Setup menu is to set the entire processor. There are 9 section including

output image 、 input image 、 text overlay 、 image quality 、 audio 、

communication、language、advance、PIP/PBP、mosaic.

LVP615U

使用说明

setup

--------------------------------------

1. Out Image ＞＞

2. Input Video Signal ＞＞

3. Text Overlay ＞＞

4. Color&Brightness,etc ＞＞

5. Audio ＞＞

6. Communication ＞＞

7. 语言/Language ＞＞

8. Advance ＞＞

After the system starts ， Press Setup to enter the setup menu.Then

press↑,↓ button to select the corresponding menu item to be set. Press OK

button to enter and return back upper level menu. The following is a

detailed description of each menu function

：

6.1 Output image setting

Press Setup to enter setup menu. Press ↑,↓ button to select“1.Out

LVP615U

使用说明

image” item.Then press OK button to enter the following image“1.Out

image” item.

1.Out Image

--------------------------------------

1.1 Resolution 1920x1080_60

1.2 Out Width 1920

1.3 Out Height 1080

1.4 Out H_Start 0

1.5 Out V_Start 0

1.6 Test Pattern off

6.1.1 Set output format

LVP615U can output image from the VGA OUT and 2 DVI OUT.

There are 16 fixed output format and custom output format.（refer to page 9specifications） . Users can select fixed output format not less

that the LED screen resolution or select custom output format which

can realize pixel to pixel display in concert with 2.1 .1 custom DVI

EDID.

Operation steps：

Press ↓to select “1.1 Resolution” item. Rotate knob to select

suitable output format，like“1280×1024_60”，Press OK button, the

screen will display confirmation menu. Press OK button again to

confirm the output format. The device will restart automatically.

LVP615U

使用说明

tips

--------------------------------------

Data will reset Press <OK> to reset Press <return> to cancel

Note: to custom output format，after selection，need further set

1.1.1 custom width、1.1.2 custom height and 1.1.3 custom V frequency.

Press ↓ button to 1.1.4 Apply，Press “OK”to make parameters

effective.

1.1 Custom Resolution

--------------------------------------

1.1.1 Cus. Width 1920

1.1.2 Cus. Height 1002

1.1.3 Cus. V Freq. 60

1.1.4 Apply OK To Apply

+ 82 hidden pages

Vdwall LVP615U, ledsync820h, LVP615D User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual