Appendix: modify the record table ----------------------------------------------------- 98
3
LVP615 User Manual
Chapter 1: Safety precautions
!Danger
There is high voltage in the processor, to prevent any unexpected
hazard, unless you are maintenance, please do not open the cover
of the device.
!Warning
1. This device shall not encounter water sprinkle or splash,
please do not place anything containing water on this device.
2. To prevent fire, keep this device far from any fire source.
3. If this device gives out any strange noise, smoke or smell,
please immediately unplug the power cord from receptacle, and
contact local dealer.
4. Signal cables are not hot swappable.
!Caution
1. Please thoroughly read this manual before using this device,
and keep it well for future reference.
2. In the event of lighting or when you are not going to use the
device for a long time, please pull the power plug out of
receptacle.
3. Nobody other than professional technicians can operate the
device, unless they have been appropriately trained or under
guidance of technicians .
4. To prevent equipment damage or electric shock , ple as e don’t
fill in anything in the vent of the device.
5. Do not place the devi c e near any water source or any where damp.
6. Do not place the device near any radiator or anywhere under
high temperature.
7. To prevent rupture or damage of power cords, please handle and
keep them properly.
4
LVP615 User Manual
1.5m RS232 to RJ45
8. Please immediately unplug power cord and have the device
repaired, when
1) Liquid splashes to the device.
2) The device is dropped down or cabinet is damaged.
3) Obvious malpractice is found or performance degrades.
Chapter 2 Item List
Please unpack the product carefully, then check whether all the following
things are included in the package. If anything i s found missing, pleas e contact
the dealer.
Standard accessories
The accessories supplied with this LED Video Processor may differ from
the figures contained in the User’s Manual, but they are applicable for the
regions where you live.(LED sending card is optional)
1.5m power cord*1
adapter cable*1
1.5m DVI cable*1
User manual *1
0.5m DVI cable*1
CD*1
Remote control *1 Audio connector *1
BNC-RCA adapter *3
5
LVP615 User Manual
1 3 5 2 4
4
Chapter 3 Hardware connection
3.1 Rear view
3.2 Ports description
3.2.1 Video signal inputs (INPUT)
LVP615 supports 8 video signals input as follows:
Port Description
6
LVP615 User Manual
video (PAL/ NTSC) or analog
analog RGBHV signal output,
device for monitoring (it is strongly
recommended to use this port when
to external 2 LED
transmission cards or LED transmission
channel computer DVI digital signal
V1
V2 / YPbPr
1*Composite Video (PAL/ NTSC)
1* Composite
component video input
VGA1~VGA2
DVI
HDMI
DP
EXT.
2 * PC analog signal
1* DVI ( PC digital signal)
1*HDMI (HD digital signal)
1*DisplayPort( digital signal input)
1* Extended PAL/NTSC composite video input
3.2.2Audio input signals(AUDIO)
LVP615 supports 4-channel stereo audio inputs switching. Of which,
2 channels are DP and HDMI input. The other 2 channels are AD1, AD2
external audio input. AD1 and AD2 can be mapped to any one of signal inputs,
and will be switched synchronous to the selection of video input signals.
3.2.3 Video signal output
Port Description
VGA OUT
1-channel
which can be connected to a local display
operating and setting LVP615).
DVI OUT1 /
DVI OUT2
2 same DVI digital graphic signal output,
it can be connected
DVI Loop OUT
boxes.
1loop output
7
LVP615 User Manual
TCP/IP local area network control
Serial communication interface, used to
connect the RS232 port of PC to realize
3.2.4 Other ports
Port Description
LAN
interface
USB
USB communication por t
RS232 IN
PC software control.
Serial communication cascading output
for connecting the RS232 IN of next unit,
RS232 LOOP
through single PC can control several
units.
Antenna interface of wireless control
PC(VESA standard)
HDMI1.3(CEA-861)
Display Port 1.1 ( VESA
standard)
Video:BNC
YPbPr:BNC×3
VGA:15pin D_Sub(female)
DVI:24+1 DVI_D
HDMI:HDMI port A type
DP:Display Port
Others
Control RS232/USB/LAN/WIFI/Remote control
Input voltage 100-240VAC 50/60Hz
Power consumption ≤25W
Environment
Temperature
Environment Humidity 15-85%
Product Size 483(L) x 274(W) x 66.6(H) m m
Weight
DVI OUT1:24+5 DVI_I
DVI OUT2:24+1 DVI_D
0-45 ℃
G.W.:5.7 Kg, N.W.:4.2Kg
11
LVP615 User Manual
3.5 Product dimensions
12
LVP615 User Manual
RS232 cable order:
13
LVP615 User Manual
1 2 4 3 5 8 7 6 9
10
11
Chapter 4 Front panel and remote control instructions
LVP615 supports front panel button, remote control, RS232 and LAN
control. Same printing on remote control buttons and front panel
buttons,same button functions. The instructions are as below.
4.1 Front panel buttons and r emot e control schematic
14
LVP615 User Manual
1
5 4 6
The buttons on remote
control have the same
3
9
functions as the relative
buttons on front panel.
4.1.1Input signal selection buttons
(,,,,,,,,): select the
input signal.
4.1.2 Setup buttons(,,,, ),Set the output
image parameters.
4.1.3VGAauto adjustment button ()automatically adjust the VGA
input signal.
4.1.4 Switching time setup button(): select seamless switching
time including 0 second (cut), 0.5 second,1.0 second and 1.5 second
( fade in fade out) and blend swi tc hing function.
15
LVP615 User Manual
4.1.5 PC signal bypass output ():Switch between part and full
display of PC signal. The indicator shows the current state of the input
signal.
4.1.6 PIP/PBP keys(,,,):
:PIP/PBP turn on/ off button. When the indicator is on, press
input signal selection to choose different group input or current input itself
as the PIP signal.
,,:Switch PIP/PBP model.
4.1.7 Mosaic button()Turn on /off mosaic function. The
indicator shows the current state of mosaic.
4.1.8 Freeze button () turn on / off freeze function.
4.1.9 Brightness adjustment button(,) adjust output
brightness level under user operation station.
4.1.10 remote control sensor: built- in infrared receiver.
4.2.1Open the battery compartment on the back of the remote control,
make sure the battery effective contact
4.2.2 Please aim remote control to the sensor area of LVP615, if
there is obstacle between them, LVP615 may not receive
command.
4.2.3 To make sure remote control has a good performance. If found
improper operation, please replace new battery immediately.
4.3.3 Batteries shal l not be ex pos ed to, su ch as sunl i g ht, fir e or
the like overheated environment.
Chapter 5 Basic user instructions
After LVP615 boot, it enters the operation status of last shut-down including
signal switching status, PIP/POP (or Text overlay) status and mosaic status.
Among them, PIP/PBP( or text overlay) status and mosaic status can only
realize relativefunctions and cannot do other operation. Other relative
operations are available under signal switching status. We illustrate the
common operations as below.
17
LVP615 User Manual
5.1 Input signals selection
LVP615 supports two signal switching methods including“One key
switching”and“Pre.+Take switching”. The switching method can be set in
user setup menu “2.6 switch mode”. “One key switch” is default method.
One key switch to new input signal through input signal selection buttons.;
“Pre.+Take switch” only available for seamless switching. Press input buttons
to preselect first. Then press Take button to switc h f rom c u rre nt inp ut sign a l t o
preselected signal.
18
LVP615 User Manual
1* Composite video (PAL/ NTSC) or analog
Input signal selection as follows:
Buttons Description
1* Composite video signal input (PAL/ NTSC)
component video input
2 * PC analog signal input
1*DVI digital signal input
1 * HDMI digital signal input
1* DisplayPort digital signal input
1* extended signal input
*
Note:(1) YPbPr and V2 shar e the s ame port. If need,configur e
-------------------------------------Switch Mode
Switch Time
current input sig nal. Lik e:“ Input:HDMI ” 。The second line on the
LCD display the signal status.If no active input, display” No input’.
Meanwhile,the corresponding indicator flicker. Led screen is black.
:
: 1080p_60Hz
: 1920x1080
: (0,0)
: One Key SW.
: 1.5 Sec
After select input signal, The first line on the LCD display the
If active input, display input signal format Like:“ 1080p_60Hz ” 。
5.1.2 Pre.+Take switch
LCD screen display as below:
20
LVP615 User Manual
、
Curr. Input
HDMI
Curr. In Status
Pre. Input
V1
Pre. In Status
-------------------------------------Output Size
Output Sta
Switch Mode
Switch Time
:
: 1080p_60Hz
:
: PAL
: 1920x1080
rt: (0,0)
: Pre.+Take SW.
: 1.5 Sec
Switching signal method: press input button to preselect first, LCD screen
displays the current input status and preselect input status. Then press Take
button to switch current input to preselect input.After the completion of
switching, preselect signal become the current input signal. The status of the
preselect signal indicator: when the signal is valid, the indicator flicker rapidly.
when the signal is invalid, the indicator flicker slowly.
Note:Pre.+Take switch only available for seamless switching. LVP615
supports seamless switching between any two different input groups as follow.
Same group does not support seamless switching. For example, current input
is V1( V1 in group A). Then, preselect signal is only from B,C,D group. Signal
group as follow. :
In the signal switching status, press C/F button continually can change the
current seamless switching transition time. LVP615 can achieve seamless
switching between any two different input groups of four input groups.
Switching effect includes seamless switching ( 0s) , Fad e i n / Fade out (o.5s 1s
1.5s) and blend switching.
Seamless switching(Cut): On the LCD“Switch time” is 0s. LVP615 default
switching is CUT.
Fade in fade out(Fade): On the LCD“Switch time”is 0.5s、1.0s or 1.5s. In thi s
mode, different group signals support fade in fade out switching.
Blend switching:at this moment, on the LCD, current input is the main input.
Select different group input signal as blend signal. The main input will overlay
in the blend signal. Pr ess bl end signal or main si gnal button ag ain. Then s witc h
to selected signal. The whole process is fade in fade out effect.
:
: 1080p_60Hz
:
: PAL
: 1920x1080
: (0,0)
Note:1. YPbPr does not support seamless switching, fade in
fade out or blend switching. Switching between any signal and
YPbPr signal will cause black led screen.
2. Blend switching is only for signal switching. For other
operations, press C/F to exit the blend switching state.
LVP615 allows to insert PIP window on the current display signal.
That is dual image display function(PIP/PBP)。PIP signal can be any
input signal from other input groups or current input signal itself.
(signal group refer to page 19signal group list )Dual image size can
be preset 3 modes.The detailed operation method is as follow:
Enter PIP/PBP mode: press On/Off button,the indicator will
be on. LVP615 enters PIP/PBP mode. Then press input signal button
to select PIP signal. At the same time, LCD will display main input and
pip input status and size.(as shown below)
:
: 1080p_60Hz
:
: PAL
: 1920x1080
: (0,0)
: 640x320
: (16,16)
Select PIP input signal:In PIP mode,press button to select
corresponding signal. Then this signal is configured as PIP input.
Select Main input signal:Press On/Off button to close PIP
mode.,Press button to select corresponding signal as main input
signal. Then press On/Off button to enter PIP mode to select pip
signal again.
23
LVP615 User Manual
Mosaic Input
DVI
In Status
Input Image Size
960x540
Input Image Start
-------------------------------------Mosaic out size
Mosaic out start
Mosaic PIP: off
Switch PIP/PBP mode:When PIP/PBP is on,press buttons M1、
M2、M3 directly to select display mode fast.
5.3 Mosaic operation
Multiple units LVP615 cascading can drive huge resolution LED screen. Only
when the current input is DVI, press Mosaic button and the indicator is on.
LVP615 enters to Mosaic operation. Press the button
again and the indicator is off, LVP615 exits Mosaic.
:
: 1080p_60Hz
:
: (0,0)
Note:
5.3.1 In mosaic mode, PIP display is available.
5.3.2 In foll owing conditi ons,LVP615 cannot enter mosaic status .
(1)The input signal selected is not DVI;
(2)Bypass is on;
(3)The resolution of DVI input signal is different from the
output resolution of processor.
: 1920x1080
: (0,0)
24
LVP615 User Manual
output brightness, the highest
5.4 Other basic user operation
5.4.1 Brightness selection(Brt+,Brt-)
LVP615 supports 64 level or 100 level brightness selection.
According to“8.5 bright level” selection,adjustment range has two
kinds:0~64 or 0-100. Factory default is 0-64。To make sure of full
gray scale of output image, it always set as 64(0-100 default value is
50) !
button description
BRT-
Reduce LVP615 output brig htness,the lowest is
0.
BRT+ Increase LVP615
is 64 or 100.
5.4.2 VGA input auto adjustment (Auto)
When LVP615 is in one key switch status and current valid
input signal is VGA, press Auto button to adjust VGA input signal
sampling parameter s. Then t he VGA output image can be clear and
full.
This operation is normally performed when a new VGA source
is connected. Auto adjustment time is depend on the signal status.
Normally it’s less than 1 second. Sometimes it’s necessary to
25
LVP615 User Manual
Full display,the input image is compressed and fully
Part display, the input image is not compressed.Only a
perform several t imes until the o utp ut im age is clear, full and stable.
5.4.3 Full/ part display(Bypass)
In signal switching status, press Bypass button to switch full
and part display.
This function only works when current signal is PC input signal
(VGA1/ VGA2/ DVI /HDMI /DP). Fixed other signals to Full mode.
state description
Full
displayed on the led screen and the indicator is off.
Part
part of it can be displa yed on the screen and the indicator
is on.
Note:When the width and height of input image are lower than the
LED screen real width or height value. Part display is invalid.
5.4.4 Text overlay
LVP615 allows for overlapping text, logo or flash on the current
image. The operation is as below.
When the current input display properly, enter setup
menu“3.Text overlay”, set ”3.1text overlay” on, then select text
source.Text can be produced by PowerPoint and other office software.
26
LVP615 User Manual
System info
-------------------------------------model
version
IP
Mask
Gate
MAC
Device
5.4.5 Image freeze (Freeze)
Press Freeze button and the indicator is on, the current image is
frozen. Press Freeze button again or switch to another signal to exit
Freeze status.
5.4.6 Device information view (OK)
In signal switching status, press OK to check the LVP615 current
setting and information.
: LVP615
: V0.0.8/V0.0.8
: 192.168.1.8
: 255.255.255.0
: 192.168.1.1
: 76-64-77-00-00-00
ID: 1
Chapter 6: Setup me nu instructions
Setup menu is to set the entire processor. There are 9 section including
output image、 input image、 text overlay、 image quality、 audio、
communication、language、advance、PIP/PBP、mosaic.
27
LVP615 User Manual
setup
--------------------------------------
1.
2.
>>
3.
4.
5.
6.
7.
8.
Out Image >>Input Video Signal Text Overlay >>Color&Brightness,etc >>Audio >>Communication >>语言/Language >> Advance >>
After the system starts,Press Setup to enter the setup menu.Then
press↑,↓ button to select the corresponding menu item to be set. Press OK
button to enter and return back upper level menu. The following is a
detailed description o f each me nu function:
6.1 Output image setting
Press Setup to enter setup menu. Press ↑,↓ button to select“1.Out
28
LVP615 User Manual
1.Out Image
--------------------------------------
1.1 Resolution 1920x1080_60
1.2 Out Width 1920
1.3 Out Height
1.4 Out H_Start 0
1.5 Out V_Start 0
1.6 Test Pattern off
image” item.Then press OK button to enter the following image“1.Out
image” item.
1080
6.1.1 Set output format
LVP615 can output image from the VGA OUT and 2 DVI OUT.
There are 16 fixed output format and custom output format.(refer to
page 9specifications). Users can select fixed output format not less
that the LED screen resolution or select custom output format which
can realize pixel to pixel display in concert with 2.1 .1 custom DVI
EDID.
Operation steps:
Press ↓to select “1.1 Resolution” item. Rotate knob to select
suitable output format,like“1280×1024_60”,Press OK button, the
screen will display confirmation menu. Press OK button again to
confirm the output format. The device will restart automatically.
29
LVP615 User Manual
1.1
--------------------------------------
1.1.1 Cus. Width 1920
1.1.2 Cus. Height 1002
1.1.3 Cus. V Freq. 60
1.1
t
-------------------------------------Data will reset
Press <OK> tore
Press <return> to cancel
Note: to custom output format,after selection,need further set
1.1.1 custom width、1.1.2 custom height and 1. 1.3 custom V freque ncy.
Press ↓ button to 1.1.4 Apply,Press “OK”to make parameters
effective.
ips
set
Custom Resolution
.4 Apply OK To Apply
30
Loading...
+ 83 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.