COMPETITION GRADE HIGH PERFORMANCE RADIO CONTROL RACING CAR CHASSIS KIT
1/10 ELECTRIC COMPETITION FORMULA CAR KIT
E
INSTRUCTIONS MANUAL
5
Thank you for purchasing VBC Racing product.
This VBC Racing kit is a high performance, racing grade car kit
intended for experienced racers. The kit compose of VBC
formulated composite materials, top quality full carbon fiber
chassis and high grade 7075 material which will give you a
competitive edge over the others.
Novice racer should seek advice from more experienced racer
before assembly.
Always keep this instruction manual handy at all times for quick
reference even after completing the assembly.
Before your assembly, sand the chassis edges.
Things that we should remind you.
Sand the chassis edges with #600 sand paper and apply CA
glue to the edges and counter sink holes.
Need help or support.
If you need help or you would like to leave us a comment,
please email to our support team: support@vbc-racing.com or
visit our web site www.vbcracing.com
BAG MARKED
STEP1
1
Graphite Edges Protection Procedure
01© VBC Racing FLASH04
CA
Sand the chassis edges with #600 sand paper(not included) and
apply CA glue(not included) to the edges of the chassis.
Sand the below graphite edges with #600 sand paper and apply CA glue to the edges.
A-03-VBC-1057 Flash04 Front Lower arm (Left)
*Not included in this kit
A-03-VBC-1051 Flash04 Main Chassis (3.0MM)
A-03-VBC-1058 Flash04 Front Lower arm (Right)
BAG MARKED
STEP2-3
2
Main Chassis - Bottom Plate Linkage
Install Pivot Balls onto the Main Chassis
Install Pivot Center Mount
Flash04 Pivot Ball A-03-VBC-1027 x 5
M3x6 Flathead Screw C-02-SC-F0306 x 5
Flash04 Motor Mount Bottom Plate (7075) A-03-VBC-1056 x 1
M3x12 Flathead Screw C-02-SC-F0312 x 2
M2.5x6 Flathead Screw C-02-SC-R2506 x 2
Center Pivot Bottom Support Mount A-03-VBC-1036 x 1
M3 Lock Nut C-02-SC-NN03 x 2
Center Pivot Top Clamp Plate A-03-VBC-1037 x 1
02
© VBC Racing FLASH04
Side Linkage A-03-VBC-1032 x 2
M2x6 Screw C-02-SC-R2.0x6 x 4
A-03-VBC-1051 Flash04 Main Chassis
Flash04 Pivot Ball A-03-VBC-1027
M3 Lock Nut
M3 Lock Nut
Center Pivot Bottom Support Mount
M2.5x6 Screw
Flash04 Pivot Ball
M3x6 Flathead Screw
M3x6 Flathead Screw
Flash04 Pivot Ball
Flash04 Pivot Ball
M3x12 Flathead Screw
M3x12 Flathead Screw
M3x6 Flathead Screw
M3x6 Flathead Screw
Install the Linkage
Flash04 Motor Mount Bottom Plate
M2x6 Screw
M2x6 Screw
M2x6 Screw
M2x6 Screw
M3x6 Flathead Screw
Center Pivot Top Clamp Plate
3
Rear Pod Assembly
Rear Axle Left Bulkhead A-03-VBC-1001 x 1
03© VBC Racing FLASH04
STEP2-3
BAG MARKED
Flash04 Motor Mount A-03-VBC-1002 x 1
M3x6 Flathead Screw C-02-SC-F0306 x 4
Flash04 Rear Wing Plate A-03-VBC-1055 x 1
Rear Axle Height Adjustable Mount A-03-VBC-1030 x 2
10x6mm Flanged Ball Bearing C-02-BB-1006-FB x 2
M3x12 Roundhead Screw C-02-SC-R-0312 x 4
Rear Axle Left Bulkhead
Flash04 Motor Mount
M3x6 Flathead
M3x6 Flathead
M3x6 Flathead
M3x6 Flathead
Caution
Please note the Arrow on the Rear Axle Height Adjuster Mount MUST be pointed
to the same marking between the left bulkhead and the motor mount when
adjusting the rear axle height. The car may not run straight if these markings
are not in the same position. Reference: F104 type rubber tyres should set at
the lowest position.
Assembling the Rear Axle Adjust Mounts
10x6mm Flanged Ball Bearing
10x6mm Flanged Ball Bearing
M3x12 Roundhead
M3x12 Roundhead
M3x12 Roundhead
M3x12 Roundhead
Rear Axle Height Adjustable Mount
Flash04 Rear Wing Plate
4
Rear Differential Assembly
04
© VBC Racing FLASH04
64Pitch 95T Spur Gear A-03-VBC-1046 x 1
Flash04 Ceramic Diff Balls C-02-DB-0801 x 8
Flash04 Right Wheel Hub A-03-VBC-1017 x 1
10x6mm Ball Bearing C-02-BB-1006-B x 2
Right Wheel HubOuter Wheel Nut Shaft A-03-VBC-1018 x 1
M2x14 Shaft Pin A-03-VBC-1049 x 1
Beveled Spring Washer A-03-VBC-1066 x 2
Flash04 Diff D Ring B-02-VBC-1001 x 2
BAG MARKED
STEP4-6
Place 8 Ceramic Balls into the Spur Gear
outer holes. Lightly grease the diff balls
and make sure the balls are free to move
Grease
64Pitch 95T Spur Gear
Flash04 Ceramic Diff Balls
Thrust Bearing Set A-03-VBC-1065 x 1
Spur/Axle Fitting Ring A-03-VBC-1044 x 1
M3x3 Set Screw C-02-SC-SS-0303 x 1
Flash04 Diff Shaft B-02-VBC-1006 x 1
Grease
Flash04 Diff Shaft
Flash04 Diff D Ring
10x6mm Ball Bearing
64Pitch 96T Spur Gear with Ceramic Diff Balls
Flash04 Diff D Ring
Flash04 Right Wheel Hub
10x6mm Ball Bearing
Spur/Axle Fitting Ring
Thrust Bearing Set
Beveled Spring Washer (notice the direction)
M4 Aluminum Lock Nut A-03-VBC-1024 x 1
Right Wheel HubOuter Wheel Nut Shaft
M3x3 Set Screw
M2x14 Shaft Pin
Tighten the M4 Lock Nut to adjust the differencial
BAG MARKED
STEP4-6
6
Rear Differential Assembly Continue
05
© VBC Racing FLASH04
M3x6 Roundhead Screw C-02-SC-R0306 x 2
5
M3x8 Roundhead Screw C-02-SC-R0308 x 2
Left Wheel Hub A-03-VBC-1020 x 1
M3x6 Roundhead
M3x6 Roundhead
M3x8 Roundhead
M3x8 Roundhead
M3x3 Set Screw C-02-SC-SS-0303 x 1
M3x3 Set Screw
Motor not included
Pinion Gear not included
Installing Motor and Pinion Gear
BAG MARKED
STEP7-8
7
Steering System Assembly
06
© VBC Racing FLASH04
Steering Travel Plate A-03-VBC-1010 x 1
Steering Arm A-03-VBC-1008 x 2
16mm Servo Mount Support A-03-VBC-1067 x 1
Ball Connector B-02-VBC-0045 x 3
5x8 Ball Bearing C-02-BB-0805-B x 4
3x6 Ball Bearing C-02-BB-0603 x 2
Steering Cone Washer B-02-VBC-0089 x 2
M3x6 Roundhead C-02-SC-R0306 x 2
M3x8 Set Screw C-02-SC-SS-0308 x 4
Turnbuckle Cup A-03-VBC-0039 x 2
Make 2 steering link tie-rods, follow the connector cups directions as
the above diagram. The connector cups edge to edge shall be 20mm.
Please use a caliper to measure the exact measurement
M3x32mm Turnbuckle B-02-VBC-0036 x 2
Turnbuckle Cup S A-03-VBC-0056 x 2
M3x32mm Turnbuckle
Turnbuckle Cup F
Turnbuckle Cup
Turnbuckle Cup F
Turnbuckle Cup
M3x8 Set Screw
M3x6 Set Screw
M3x8 Set Screw
Steering Travel Plate
Steering Arm
Steering Arm
Ball Connector
Ball Connector
16mm Servo Mount Support
5x8 Ball Bearing
5x8 Ball Bearing
5x8 Ball Bearing
5x8 Ball Bearing
Steering Cone Washer
Steering Cone Washer
M3x6 Roundhead
M3x6 Roundhead
Thead Lock
Thead Lock
3x6 Ball Bearing
3x6 Ball Bearing
Thead Lock
Thead Lock
Thead Lock
Thead Lock
M3x6 Set Screw C-02-SC-SS-0306 x 4
20mm
12mm
8mm
6mm
12mm Servo Mount Support A-03-VBC-1068
8mm Servo Mount Support A-03-VBC-1069
6mm Servo Mount Support A-03-VBC-1070
This kit provides additional Servo Mount
Supports in different heights. Please make
sure the servo link turnbuckle is parallel to
the Steering Travel Plate. You may need
these Servo Mount Supports for different
types of servos.
Loading...