ASSEMBLY AND INSTALLATION
INSTRUCTIONS
T0270 / T0271
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.
Hardware Package (included):
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Mounting Screw X2
#8/32X1/2 in
Mounting Screw X2
#6/32 X1/2 in
Important to Know:
1. If you are not familiar with state and local electrical
codes, it is recommended that you consult with a
qualified electrician.
2. This fixture requires a 120 VAC, 60 Hz power
source.
3. For general safety and to avoid any possible
damage to the sensor, be sure the power is
switched "off" before adjustment.
Maximum Wattage: 34 W
Working Temperature Range: -40F ~ 1130F
Mounting Screw X2
#10/24 X1/4 in
Mounting Bracket Screw
Mounting Strap
Features:
1. Energy saving LED fixture.
2. Motion sensor: turns light ON automatically when
motion is detected and turns light OFF automatically
when motion stops.
3. Photocell keeps the light OFF during daylight hours.
4. When in manual override mode, use wall switch
to keep the light ON during the night.
Note: Fixture can be wall mounted or eave mounted.
Fixture Mounting Screw
Wire Nut X3
Wall Mounted
Read notes section on page.4 and page.5 for additional information about mounting location of fixture.
Light fixture and sensor should be mounted as shown above when installed (depending upon type of installation)
Before installing the light fixture under an eave, the sensor head must be rotated as shown in the next two steps for
proper operation and to avoid the risk of electrical shock.
For eave mounted only:
Swing the sensor head towards the mounting bracket.
Mounting Bracket
Controls
Rotate the sensor head clockwise 180˚ so the controls face down.
Eave Mounted
Controls
Controls
Page 1 / 5
160518
Wire Nut (G)
Outlet Box
FRONT
Mounting Bracket
Mounting Bracket Screw
Back Plate
Light Head
Mounting Strap
Fixture Mounting Screw
Mounting Screw
Sensor
Installation Steps
Turn off the power at fuse or circuit box.
Fig. 1
1. The fixture mounting bracket is pre-assembled on the light fixture. Unscrew
the fixture mounting screw in order to remove the mounting bracket.
2. Install the mounting strap to the outlet box with the stamped word “FRONT”
facing away from the outlet box, using two mounting screws that best fit the
outlet box. Mounting bracket should sit flush against wall surface when
secured.(Choose one matching pair of suitable mounting screws from the 3
pairs provided)
3. Pull out the source wires from the outlet box. Make wire connections using
wire nuts as follows:
---Connect the black wire from the fixture to the “hot” wire from the power
source. (usually black)
---Connect the white wire from the fixture to the neutral wire from the power source. (usually white)
---Connect the grounding wire from the fixture to the grounding wire from the power source. (usually green / yellow
insulation)
Carefully tuck the wires back into the outlet box.
4. Place mounting bracket against the outlet box, insert the mounting bracket screw through the mounting bracket hole,
thread mounting bracket screw into the center hole of the mounting strap. Tighten the mounting bracket screw securely.
▲ When mounting to a wall, the “UP” arrow must point upward. (See Fig. 1)
▲ When mounting to an eave, the “UP” arrow must point toward the building.
5. Attach the back plate of the light fixture to the mounting bracket, secure it with the fixture mounting screw.
6. With silicone caulking compound, caulk completely around where the mounting bracket meets the wall surface.
CAUTION: Be sure to caulk completely where the mounting bracket meets the wall surface to prevent water
from seeping into the outlet box.
Turn on the power at the main fuse or circuit breaker box.
Adjusting the Sensor Head:
1. Aim sensor head toward desired detection area, maintaining a
5° - 40° downward angle to allow moisture to drain.
Note: Make sure sensor head is positioned with control knob facing
towards the ground.
2. You can rotate the sensor head up and down to change the coverage
sensor
area. (See Fig. 2) Walk through the detection zone at the farthest
distance you wish to detect motion.
Fig. 2
Note: Range set too high may increase false triggering.
(See Fig. 3 and Fig. 4 on Page 3)
Page 2 / 5
160518
Fig. 3
Fig. 4
Adjustment Sensor Higher For Long Coverage
Sensitivity of Motion Sensor
● You can adjust the sensitivity of the motion sensor by using the “SENSITIVITY” selector located on the right side
of the bottom surface of the sensor. (See Fig. 6)
● Adjust motion sensor sensitivity to HIGH (H), MEDIUM (M), or LOW (L) to achieve desired performance.
● Approximate range for each setting: 20 ft. (L), 45 ft. (M), 70 ft. (H).
Adjusting the Light Head:
1. Gently grasp the light heads and tilt them up or down, left or right to
adjust the light coverage area. Keep the light heads at least 1˝ (25mm)
away from the sensor.(See Fig. 5)
2. Keep the light heads 30˚ below horizontal to avoid water damage and
electrical shock.
Adjustment Sensor Lower For Short Coverage
Fig. 5
Function and Operation
Choose a mode by sliding the switch on the bottom of the sensor. (See Fig.6)
Note: When power is first applied, the light will turn on to 100% brightness. The sensor will take 30 seconds
to warm up.
1. Test mode (daytime or nighttime operation )
● Rotate the knob on the left side of the back plate to the “TEST”
position (See Fig.7)
● With the power on, the light turns to low-level brightness
automatically.
● The light turns to high-level brightness when motion is detected,
and stays on as long as the motion continues. Then it reverts back
to low-level brightness about 5 seconds after motion is no longer
detected.
Note: You can adjust the low level brightness (0~50%) by using
the low level brightness knob on the right side of the back plate.
(See Fig. 7)
Fig. 6
Sensitivity
Mode
2. AUTO MODE (nighttime operation only)
● To shift to “AUTO” mode, rotate Time Delay knob arrow to point to
the desired time setting (between 5 seconds and 3 minutes). At
dusk, the light turns on to pre-selected low level brightness. When
motion is detected, the light turns to full brightness and stays on as
long as motion continues. When the motion is no longer detected,
the light at full brightness remains on for the predetermined time you
set (5s ~ 3min), and then switches back to low level automatically.
● The light turns off automatically at dawn.
Note: You can adjust the low level brightness (0~50%) by using
the low level brightness knob. (See Fig. 7)
Page 3 / 5
Fig. 7
Delay Time Low Level Brightness
160518
3. 3 HOURS (3H) MODE (nighttime operation only)
● The light turns to high-level brightness (100%) at dusk, and stays "ON" for 3 hours. Then it turns to low-level s
brightness. It turns to high-level brightness (100%) when motion is detected, and stays on as long as motion
continues. When motion is no longer detected, it remains on for the predetermined shut-off delay time you
set (5s~3min), and then returns to the predetermined low-level brightness automatically.
● The light turns off automatically at dawn.
Note: You can adjust the low level brightness (0~50%) by using the low level brightness knob. (See Fig. 7)
4. 6 HOURS (6H) MODE (nighttime operation only)
● The light turns to high-level brightness (100%) at dusk, and stays "ON" for 6 hours. Then it turns to low-level
brightness. It turns to high-level brightness (100%) when motion is detected, and stays on as long as motion
continues. When motion is no longer detected, it remains on for the predetermined shut-off delay time you
set (5s~3min), and then returns to the predetermined low-level brightness automatically.
● The light turns off automatically at dawn.
Note: You can adjust the low level brightness (0~50%) by using the low level brightness knob. (See Fig. 7)
5. PHOTOCELL (PC) MODE (nighttime operation only)
● The light turns on to full brightness at dusk and remains
“ON” until dawn.
Fig. 8
Manual Override Operation Diagram
6. Manual Override (nighttime operation only)
● To temporarily override the settings in “AUTO”, “3H” or “6H”
modes for on-demand continuous full-brightness at night,
turn the wall switch “OFF” then turn it “ON” twice within 3
seconds. The light remains on all night long. To shift back
to “AUTO”, “3H” or “6H” mode, turn the wall switch “OFF”
then turn it “ON” twice within 3 seconds again.
● The light turns off automatically at dawn.
“AUTO” “3H”
or “6H” Mode
Turn wall switch OFF-ON
-OFF-ON in 0.5~3
Seconds
Turn wall switch OFF-ON
-OFF-ON in 0.5~3 Seconds
Manual
Override
Note: To make sure the above functions operate properly, always keep the wall switch in the “ON” position
(including the daytime).
Customization Options:
Shut-off Delay
● The shut-off delay is the length of time the light will stay at brightness after motion has ceased to be detected.
● You can set the shut-off delay by rotating the delay time knob arrow so it points to the desired time setting within
“TIME” range. To increase the shut-off delay, turn the knob clockwise. To decrease the shut-off delay, turn the
knob counterclockwise.
Notes:
1. The sensitivity of the motion sensor will increase as the
environmental temperature gets cooler. You may wish to
make adjustments when the season changes.
For best performance, gently clean the lens with a soft
cloth every 1 or 2 months to assure maximum sensitivity.
2. For best performance, install fixture at least 8 feet above
the ground. At such a height, the fixture will provide a
detection distance of up to 70 feet at 77 degrees
Fahrenheit. (See Fig.9)
3. The sensor detects movement across a detection range
of 360 degrees. (See Fig.10)
Where you install your fixture is important:
Be sure the light is mounted straight on the wall
or eave; otherwise, the detection distance may
be limited.
Fig. 10
12.0'
8.0'
20'
Fig. 9
360˚
70'
Page 4 / 5
160518
4. The sensor will be more sensitive to motion across its
detection path than motion directly towards it. (See Fig.11)
Fig. 11
5. To reduce possible nuisances, do not mount the fixture
Motion
near a heat source like an air conditioner, vent or furnace
exhaust, or in a direction facing any reflecting object or
other light source.
Sensor
Least sensitive
Troubleshooting
---The light does not come on at all:
1. Make sure the wall switch and circuit breaker are on.
2. Make sure the wiring is correct.
3. Cover the sensor with dark color cloth to verify that the ambient light level is not too high.
---After performing 3H or 6H Mode, the light stays on full brightness after 3 minutes:
1. Make sure there is no movement that could be picked up by the sensor.
2. Adjust the delay time knob counterclockwise to reduce the delay shut-off time.
---In Manual override, the light stays on after dawn:
1. The ambient light level may be too low due to overcast skies.
The following parts are available for re-order if damaged or missing.
Motion
Most sensitive
Mounting Screw X2
#8/32X1/2 in
Mounting Screw X2
#6/32 X1/2 in
Mounting Screw X2
#10/24 X1/4 in
Mounting Bracket Screw
Assembly Kit
5077MM (1 SET)
Mounting Strap
Fixture Mounting Screw
Wire Nut X3
5-YEAR LIMITED WARRANTY:
All products are warranted to be free of defects in material and workmanship for five (5) years from date of purchase.
This warranty is limited to the correction of any such defect, or the replacement of any such defective item(s), provided
that: (a) we are properly notified and consent to return of the item(s) in question:(b) the item(s) is / are returned with proof
of purchase date; and (c) it is found upon inspection by us that the item(s) is / are defective as noted above. This warranty
does not cover labor costs, consequential damages, nor does it apply to any item(s) that have been improperly installed,
overloaded, altered, or otherwise abused by the customer, its agent(s) or employee(s). Finishes are specially excluded
from the terms of this warranty since they are subject to environmental maintenance deemed beyond our control. Other
than the described obligation, we assume no further liability with respect to the sale or use of our products.We make no
warranty, express or implied, and disclaim any warranty of merchantability or fitness for a particular purpose.
A
C
A: 13-1/8"
B
Page 5 / 5
B: 9"
C: 6-3/8"
160518
Loading...