www.vax.co.uk
Please read carefully before using this cleaner.
Always fully extend the mains cable before use.
R
e
tain f
or future reference.
Vax careline
0870 6061248
instruction manual
Bagless upright
Vax model number:
VZL-801
Vax VZL-801 User Guide_Amended.qxd 22/3/07 2:00 pm Page 1
1. Diagram
www.vax.co.uk
2
parts overview
1
2
13
1
5
17
19
20
23
12
9
3
4
5
22
21
18
16
14
6
7
8
11
10
1
So
ft grip handle
2 Brushbar on/off switch
3
P
o
w
er on/off switch
4 Stretch hose handle
5
S
tr
e
tch hose release button
6 Removable flexible hose
(inside tube)
7
Brush edge
8 Stair hose anchor
9 Motor protection switch
10 Headlight
11
Brushbar vie
w windo
w
12 Patented edge cleaning
13
C
or
d Clip
14 On-board crevice tool
15
On-boar
d s
tair t
ool
16 Stair hose anchor clip
17
C
ontainer release
(push do
wn)
and carrying handle (lift up)
18 Cyclonic air separator
19 Dirt container
20
P
os
t-motor filter
21 Cord rewind pedal
22
Plug
23 Wheels
24
Dirt C
on
tainer - fr
ont
25 Dirt Container - back
Fig.1/1
2524
Vax VZL-801 User Guide_Amended.qxd 22/3/07 2:00 pm Page 2
3
Vax Careline 0870 606 1248
safety information
2. Safety Information
For Household Use Only
When using the vacuum cleaner, basic safety precautions
should always be observed, including the following:
1. Only use the vacuum cleaner indoors on dry
surfaces.
2. Turn off the vacuum cleaner controls before
connecting or disconnecting from the mains supply.
3. Always unplug the vacuum cleaner before
connecting or disconnecting the vacuum hose and
accessories.
4. Close attention is necessary when used by or near
children. Do not allow children to use as
a toy.
5. Use only as described in this manual.
Use only the manufacturer’s recommended
attachments.
6. Do not use the vacuum cleaner if it has been
dropped, damaged, left outdoors or dropped into
water. Do not use the vacuum cleaner with a
damaged cord or plug. If the supply cord or plug is
damaged, return the vacuum cleaner to a Vax
Authorised Service Agent or suitably qualified
person for examination, repair or adjustment.
7. Do not pull or carry by the cord. Do not use the cord
as a handle, close a door on the cord or pull the cord
around sharp edges or corners. Do not run the
vacuum cleaner over the cord. Keep the cord away
from heated surfaces.
8. Do not handle the plug or vacuum cleaner with wet
hands. Do not use outdoors or on wet surfaces.
9. Do not put any objects into openings. Do not use
with any openings blocked and do not restrict air
flow. Keep all openings free of dust, lint, hair or
anything that may reduce airflow.
10. Keep hair, loose clothing, fingers and all parts of the
body away from openings and moving parts.
11. Do not pick up hot coals, cigarette butts, matches or
any hot, smoking or burning objects.
12. Do not pick up flammable or combustible materials
(ligh
ter fluid, petrol, kerosene, etc) or use in the
presence of explosive liquids or vapours.
13. Do not vacuum up harmful or toxic material (chlorine
bleach, ammonia, drain cleaner, etc).
14.
Do no
t v
acuum up hard or sharp objects such as
glass, nails, scr
e
ws, coins, etc.
15. Do not use without the filters in place.
16. Take extra care when vacuuming on stairs.
17. Keep vacuuming area well lit.
18. Store the vacuum cleaner indoors in a cool, dry area.
19. Turn off the on/off switch before unplugging the
vacuum cleaner.
20. Use only CE-approved 13 amp extension cords. Nonapproved extension cords may overheat. Care should
be taken to arrange the cord so that the cord cannot
be pulled or tripped over.
WARNING: Always switch off and unplug the
vacuum cleaner from the electrical outlet
before assembling, opening or emptying the dirt
container, or before connecting/disconnecting the
attachments.
CAUTION: The vacuum cleaner is a very powerful
unit. Before plugging the cord into the electrical
outlet, make sure the switch is in the ‘off’ position. Hold
the vacuum cleaner firmly when starting and in use.
IMPORTANT: If the inlet, hose or telescopic tube is
blocked, switch off the vacuum cleaner and
remove the blockage(s) before re-starting the vacuum
cleaner.
IMPORTANT: Cleaning filters regularly improves
vacuum performance. Make sure all filters are
replaced back into the vacuum cleaner before using. This
vacuum cleaner is intended for household use only and
not for commercial or industrial use.
PLEASE KEEP THESE INSTRUCTIONS FOR
FURTHER USE.
Motor Thermostat
IMPORTANT: The motor is equipped with a
thermal cut-out. If for any reason, the vacuum
cleaner should over-heat, the thermostat will
aut
oma
tically turn the unit off. Should this occur,
unplug the vacuum cleaner from the electrical outlet
and turn off the switch. Remove the dirt container
and emp
ty. Clean the filt
ers. Allo
w the cleaner t
o c
ool
for approximately one (1) hour. To re-start, plug into
an electrical outlet and switch back on.
Vax VZL-801 User Guide_Amended.qxd 22/3/07 2:01 pm Page 3
www.vax.co.uk
4
use & function / how to operate
3. Use & Function
IMPORTANT: Always remove the power plug from the
electrical outlet before assembling or removing
accessories.
1. Pull the stretch hose tube to the front of the cleaner
and press hose into handle assembly (Fig. 3/1).
2. Insert excess cord into handle of the cleaner by
pushing down into lower handle (Fig. 3/2).
WARNING: Avoid pinching cord while inserting into
handle.
3.
Align handle on
to base of cleaner.
4. Using a Phillips or Flat Head screwdriver, secure the
handle by inserting the provided four (4) screws into
the back of the handle (Fig. 3/3).
5. Connect the stretch hose tube to the opening on the
base and push the stretch hose handle towards the
machine until it snaps into place (Fig. 3/4).
4. How to Operate
Transporting your Cleaner
1. Use the carry handle located on the dirt container lid
(Fig. 4/1).
Fig.3/1
Fig.3/3
Fig.3/4
Fig.4/1
Fig.3/2
Vax VZL-801 User Guide_Amended.qxd 22/3/07 2:01 pm Page 4
5
Vax Careline 0870 606 1248
how to operate
S
tarting Up
1. Holding the power cord by the plug, pull cord out
completely. The red tag will indicate the end of the
cord. Plug into the outlet (Fig. 4/2).
2. For easier handling while vacuuming, hook the power
cord onto the power cord hook (Fig. 4/3).
3. Switch the upright vacuum cleaner on or off by
pressing the on/off switch (Fig. 4/4).
B
rush Vacuuming
1. Tilt the upright vacuum cleaner back before you start
vacuuming. At the same time, use your foot to press
the nozzle down onto the carpet (Fig. 4/5).
Brush Vacuuming on carpeted floors:
• The brushbar is switched on or off using the brushbar
on/off switch (Fig. 4/6). Switch brushbar on for carpeted
floors.
• The rotating brushbar loosens deeply embedded dirt
and brings it to the surface.
Vacuuming on smooth surfaces:
• Switch brushbar off to obtain the best results when
vacuuming smooth barefloor surfaces.
Brushbar Reset
1. If something becomes lodged and the brushbar shuts
off, turn the cleaner off and remove obstruction. Press
the r
eset button at the back of the cleaner head to
reset the brushbar motor. (Fig. 4/7).
Fig.4/2
Fig.4/5
Fig.4/3
Fig.4/4
Fig.4/6
Fig.4/7
Vax VZL-801 User Guide_Amended.qxd 22/3/07 2:01 pm Page 5
www.vax.co.uk
6
accessories
5. Accessories
Vacuuming with Accessories
1. Press the release button to release the stretch hose
tube. The stretch hose tube with built-in brush can be
used for cleaning surfaces (Fig. 5/1).
2. While pressing the hose release button, pull out the
suction hose to release from stretch hose tube (Fig. 5/2).
3. Straighten the hose and hook the hose clip into the
fastening ring to prevent the upright vacuum cleaner
from toppling over during use (Fig. 5/3).
4. To access the tools, rock the stair cleaning tool away
from the cleaner. To remove the tools, grasp the tool
and pull up and out of the accessory clip (Fig. 5/4).
5. Then attach the accessory to the suction hose
(Fig. 5/5).
Vacuuming Upholstery, Furniture, and Curtains
1. Slide the hose into the stretch hose tube until locking
the mechanism engages (Fig. 5/6).
Fig.5/1
Fig.5/2
Fig.5/3
Fig.5/4
Fig.5/5
Fig.5/6
Fas
t
ening Ring
Hose Clip
Vax VZL-801 User Guide_Amended.qxd 22/3/07 2:01 pm Page 6
7
Vax Careline 0870 606 1248
dirt container and director removal
2. Use the stretch hose tube as an extension for long
reaches (Fig. 5/7).
3. After vacuuming, slide the suction hose back into the
stretch hose tube while holding the hose release
button (Fig. 5/8).
6. Dirt Container and Director:
Removal & Replacement
WARNING: To reduce the risk of injury from
moving parts, unplug before servicing.
NOTE: Unplug the vacuum cleaner before cleaning the air
director.
1. The dirt container must be emptied as soon as or before
the maximum capacity mark is reached (Fig. 6/1).
2. Unlock and remove the dirt container by pushing the
carry handle down and away from the machine (Fig. 6/2).
3. Tapping the container several times will loosen any
dust that may have become attached to the air
director. (Fig. 6/3).
Fig.5/7
Fig.5/8
Fig.6/1
Fig.6/2
Fig.6/3
Vax VZL-801 User Guide_Amended.qxd 22/3/07 2:01 pm Page 7
www.vax.co.uk
8
dirt container and director removal
4. Empty the container by pressing the dirt container
release button over a rubbish bin (Fig. 6/4-5).
5. Close the dirt container and replace back into the
vacuum cleaner until you hear it click (Fig. 6/6).
NOTE: Check the dirt container is secured in place before
lifting the vacuum cleaner.
T
o clean the air separator:
1. To remove air separator, rotate 1/4 turn
counterclockwise (Fig.6/7).
2. Pull out and wipe with a damp cloth to clean.
3. Dry and return the air separator to the dirt container.
Rotate 1/4 turn clockwise to lock in place (Fig.6/8).
Fig.6/4
Fig.6/5
Fig.6/6
Fig.6/8
Fig.6/7
Vax VZL-801 User Guide_Amended.qxd 22/3/07 2:01 pm Page 8
9
Vax Careline 0870 606 1248
brushbar removal and replacement
Cleaning The Post-motor Filter
IMPORTANT:
Switch off the vacuum cleaner and
unplug from the wall outlet.
NOTE: Vax recommends cleaning the post motor filter
every 2-3 months.
1. Remove the dirt container.
2. Lift out the post-motor filter cover by pressing the
locking tab and remove it (Fig. 6/9).
3. Lift out post motor filter and tap clean on the inside of
a bin (Fig.6/10) This filter can be washed under
running cold water. Leave to dry for 24 hours before
replacing in the vacuum cleaner.
4. Replace filter back into housing and snap filter cover
back into position. Replace dust container (Fig.6/11)
7. Rotating Brushbar: Removal &
Replacement
The motor switches off automatically if the brushbar is
blocked during operation by vacuuming up foreign
objects, or if strands of carpet are wrapped around it.
IMPORTANT: Switch off the vacuum cleaner and
unplug it from the wall outlet before servicing.
1. Lay the vacuum cleaner down on a flat surface and
turn over to expose the brushbar. Using a pair of
scissors, cut through any threads or hairs caught by
the brushbar that have wrapped around the guides
(Fig. 7/1).
2. There is an automatic system which cuts off the power
supply if the brushbar gets clogged up. After cleaning
the brushes, wait for 2 minutes then plug the vacuum
cleaner into the wall outlet and press the reset button
(Fig. 7/2) before pressing the power on/off switch.
Fig.6/9
Fig.6/10
Fig.7/1
Fig.7/2
Reset Button
Fig 6/11
Vax VZL-801 User Guide_Amended.qxd 22/3/07 2:01 pm Page 9
www.vax.co.uk
10
maintenance
8. Maintenance
IMPORTANT: Switch off the vacuum cleaner and
unplug it from the wall outlet before servicing.
Hose Blockage
1. Lift out the stretch hose tube (Fig. 8/1).
2. Remove the stretch hose from the stretch hose tube
(Fig. 8/2).
3. Pull the stretch hose to one side to remove it from the
dirt container (Fig. 8/3).
4. After removing the hose use a feather duster to brush
it clean and remove the blockage (Fig.8/4).
5. Push the stretch hose back onto the inlet on the dirt
container and insert the other end of the hose back
into the stretch hose tube (Fig. 8/5).
6. Return the stretch hose tube to the vacuum cleaner
until it clicks into place (Fig. 8/6).
Fig.8/1
Fig.8/2
Fig.8/3
Fig.8/4
Fig.8/5
Fig.8/6
Vax VZL-801 User Guide_Amended.qxd 22/3/07 2:01 pm Page 10
11
Vax Careline 0870 606 1248
troubleshooting / service / technical specification
9. Troubleshooting
W
ARNING:TO REDUCE RISK OF PERSONAL INJURY,
UNPLUG VACUUM CLEANER BEFORE SERVICING
PROBLEM: Cleaner won’t run
Cause: Not properly plugged into wall outlet.
Solution: Plug in firmly.
Cause: No electricity in wall outlet.
Solution: Check fuse or breaker.
Cause: On/off switch not turned on.
Solution: Push on/off switch to on.
Cause: Motor thermostat has tripped.
Solution: Switch off and unplug the vacuum cleaner.
Leave for one (1) hour. See page 3.
Cause: Blown fuse/tripped breaker.
Solution: Reset circuit breaker or replace fuse.
PROBLEM: Cleaner won't pick up
Cause:
Full or clogged dirt container.
Solution: Clean dirt container.
Cause: Clogged nozzle.
Solution: Remove obstruction.
Cause: Clogged dirt inlet.
Solution: Remove suction channel cover and remove
obstruction.
Cause: Clogged hose.
Solution: Remove obstruction.
Cause: Hose not inserted fully.
Solution: Push hose in securely.
Cause: Dirty filters or filter container.
Solution: Clean/change filters or filter container.
PROBLEM: Accessories won't pick up
Cause:
Accessories not attached correctly.
Solution: Refer to page 6 and 7 for fitting information.
PROBLEM: Brushbar does not turn
Cause:
Brushbar blocked.
Solution: Remove blockages.
PR
OBL
EM:
Air flow restricted with attachment use
Cause:
Attachment use restricts air flow.
Solution: Check attachment.
Cause: New carpet debris clogging air path.
Solution: R
emove obstruction.
10. UK Service & Help
Vax Care 0870 6061248
Monday-Friday 9.00am to 5.00pm.
An answerphone is available outside of these hours. Any
queries or concerns about using the Vax, call the Vax
Careline. Calls are charged at the UK national rate.
Please make a note of the serial number and model
number of the carpet cleaner before calling. There are
over 400 approved Vax Service Agents in the UK. For the
nearest Service Agent, please call the Vax Careline.
www.vax.co.uk
11. Technical Specification
Voltage: 220 – 240V ~50Hz
Wattage: 1700W
Capacity: 2l
Filters: Foam pre-motor filter
Cord Length: 9.8m
Weight: 8.98kg
Subject to technical change without notice.
Vax VZL-801 User Guide_Amended.qxd 22/3/07 2:01 pm Page 11
EEC STATEMENT OF COMPLIANCE
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
VZL-801 VXZERO Upright is manufactured in compliance with the following Directives:
Safety: 73/23/EEC Low Voltage Directive
EMC: 89/336/EEC Electromagnetic Compatibility Directive
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK
email: info@vax.co.uk - website: www.vax.co.uk
Vax VZL-801 User Guide_Amended.qxd 22/3/07 2:01 pm Page 12
Loading...