Page 1
www.vax.co.uk
Please read carefully before using this cleaner.
Always fully extend the mains cable before use.
Retain for future reference.
Vax careline
0870 6061248
instruction manual
Carpet Washer
Vax model number:
V-020 PU
Vax V-020PU User Guide v2.qxd:Vax V-020(PU) User Guide 17/6/08 10:02 Page 1
Page 2
1. Diagram
www.vax.co.uk
2
parts overview
AAA
ANTI
ALLERGEN
ADDITIVE
1 Power Button (Red)
2 Water Pump Button (Green)
3 Carry Handle
4 Power Cord
5 Container Release Clips
6 Casters
7 Hose Connection Port
8 Solution Tube Port
9 Exhaust Filter
10 Hose
11 Hose Cylinder Connector
12 Solution Tube
13 Solution Tube Connector
14 Fibreflow Wash Head
15 Upholstery Wash Tool
16 Pre-treatment wand
17 Vax AAA Carpet Cleaner
18 Vax Pet Solution
19 Pre-treatment solution
9
5
15
16
17
13
13
12
10
11
14
1
2
3
4
8
7
6
18
pre
treatment
p
re-treatment
c
arpetsolution
solutiondeprélavage
p
ourtapiset moquettes
t
eppichvorwaschspray
tapitreinigerspray
19
Vax V-020PU User Guide v2.qxd:Vax V-020(PU) User Guide 17/6/08 10:02 Page 2
Page 3
3
V
ax Careline 0870 606 1248
safety information
2. Safety Information
For Household Use Only
When using the carpet washer, basic safety precautions
should always be observed, including the following:
1. Do not leave the carpet washer unattended when
plugged in. Unplug it from socket when not in use.
2. To prevent electric shock do not use outdoors.
3. Not to be used as a toy. Close supervision is
necessary when used by or near children or the
infirm.
4. Use only as described in this manual.
5. The appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
6. Do not use with a damaged cord or plug. If the
supply cord and/or plug is damaged, they must be
replaced by the manufacturer, a Vax Service Agent
or similarly qualified persons in order to avoid hazard.
7. Do not pull or carry by the cord, use the cord as a
handle, allow the cord to come into contact with
hot or sharp surfaces or close a door on the cord.
8. Do not unplug by pulling on the cord.
9. Do not handle the plug or carpet washer with wet
hands.
10. Do not put any objects into openings or operate
with openings blocked, keep them free of anything
that may reduce airflow.
11. Keep hair, loose clothing, fingers and all parts of
the body away from openings and moving parts.
12. Do not use the carpet washer on any glowing,
burning or smoking particles.
13. Do not use without the solution tank and dirty
water tank in place.
14. Turn off all controls before unplugging.
15. Do not use to pick up flammable or combustible
liquids such as petrol, or use in areas where they
may be present.
16. Keep the carpet washer on the floor.
17. Do not use an extension cord.
18. Do not attempt to remove blockages with sharp
objects as they may cause damage.
19. Store indoors put away after use to prevent tripping
accidents.
20. Using improper voltage may result in damage to the
motor and possible injury to the user. The correct
voltage is listed on the rating label.
21. A hazard may occur if the carpet washer runs over
the power supply cord.
NOTE: Carpets should be dry vacuumed
thoroughly before washing.
NOTE: If the supply cord is damaged, it must
be replaced by the manufacturer, a Vax
service agent or similarly qualified persons in order
to avoid hazard.
NOTE: The carpet washer must be unplugged
from the mains socket outlet after use, and
before cleaning or maintaining the carpet washer.
IMPORTANT: This carpet washer is not
intended for commercial use.
!!!
!
Vax V-020PU User Guide v2.qxd:Vax V-020(PU) User Guide 17/6/08 10:02 Page 3
Page 4
www.vax.co.uk
4
preparing the carpet / pre-treating the carpet
3. Preparing the Carpet
IMPORTANT: Do not use the Carpet Washer as a
dry vacuum.
1. Vacuum carpet thoroughly. Use a vacuum cleaner
with a revolving brushbar for best results.
2. Remove as much furniture from the room as
possible. If unable to remove the furniture, place
plastic or foil under and around the legs until the
carpet has dried completely.
Helpful Hints for Carpet Cleaning:
1. Only use Vax AAA Carpet Cleaner with this carpet
washer.
2. Do not oversaturate carpet with cleaning solution
while using the carpet washer.
3. For heavily soiled areas, additional applications may
be necessary.
4. Allow plenty of time to dry carpet thoroughly.
5. Wipe cleaning solution from woodwork and wood
to prevent any damage.
6. Try not to walk on carpet until it is completely dry.
7. After carpet is thoroughly dry, vacuum the carpet
using a vacuum cleaner with a revolving brushbar.
8. Before cleaning, determine where to start and end,
making sure not to walk over previously cleaned
areas.
Check for Colour Fastness:
Before cleaning carpet, test for colour fastness. Dampen a
white cloth with solution. Test a small area in a closet.
Gently rub the cloth over the area. Check each colour for
colour bleeding. If the cloth remains clean, it should be
safe to clean the carpet.
After Cleaning:
• Allow carpet to dry completely. Try not to walk on
the carpet until it is dry.
• If it is necessary to walk on the carpet, place white
towels on the areas to be walked on.
• If the carpet is not dry and the furniture must be
placed back in the room, use plastic or foil under
the furniture to prevent staining the carpet.
• Thoroughly clean the dirty water tank with warm
(max 40ºC) tap water.
4. Pre-treating the Carpet
Unclip Container Release Clips (A) on both sides of
machine (Fig.4/1).
Lift off Motor Container to reveal Clean Water Tank (A)
situated inside Dirty Water Tank (B) (Fig.4/2).
Remove clean water tank (A) from the inside of the dirty
water tank and fill with warm water (max 40°C) to point
indicated on the tank. Add 3 capfuls of Vax pre-treatment
solution per litre of water (unless otherwise stated on the
bottle) (Fig 4/3).
!
Fig.4/1
Fig.4/2
Fig.4/3
A
A
A
B
Vax V-020PU User Guide v2.qxd:Vax V-020(PU) User Guide 17/6/08 10:02 Page 4
Page 5
Replace Clean Water Tank (A) inside Dirty Water Tank (B)
taking care to ensure that the space to allow the dirty
water back into the tank is lined up with the Solution Port
(C) (Fig.4/4).
Replace Motor Container (A) ensuring that the Solution
Pump Hose (B) is aligned with the hole in the Clean Water
Tank (C) so that it goes inside when the Motor Container
is clipped back into position (Fig.4/5).
WARNING: Machine must not be plugged in
during this stage.
Push the pre-treatment wand connector (A) into the
solution port (A1) (Fig.4/6).
Once the pre-treatment has been connected, press the
water pump button to on.
Using the wand and the trigger, apply the water and
solution to the carpet (Fig.4/7) Turning the spray nozzle
clockwise or anti-clockwise will alter the spray pattern
Releasing the trigger will stop the solution flow. The
treated areas should be left for 10-15 minutes (Fig.4/8).
NOTE: Do not over wet carpets
5
V
ax Careline 0870 606 1248
pre-treating the carpet
A
C
Fig.4/4
B
Fig.4/5
A
B
C
Fig.4/6
A
A1
!
Fig.4/7
Fig.4/8
Vax V-020PU User Guide v2.qxd:Vax V-020(PU) User Guide 17/6/08 10:02 Page 5
Page 6
www.vax.co.uk
6
assembly
5. Assembly
Push Solution Tube Cylinder Connector (A) firmly into
Solution Port (A1).
Twist Solution Tube Cylinder Connector (A1) a quarter
turn to the right to lock into place (Fig.5/1).
Push Hose Cylinder Connector (B) firmly into Hose
Connection Port (B1).
Twist to the right until Hose Cylinder Connector Locks
into place (Fig.5/2).
Wrap Solution Tube (A) around Hose (B). Ensure that
the solution tube is wrapped loosely enough to allow
the solution to flow freely through the tube (Fig.5/3).
After wrapping the tube around the hose, affix Solution
Tube (A) to Hose (B) using Clips provided (C) to hold it in
place (Fig.5/4).
Push end of Solution Tube onto connective valve
on the Wash Head / Upholstery Tool (Fig.5/5).
Fig.5/4
A
B
C
Fig.5/5
Fig.5/3
A
B
Fig.5/1
A
A1
Fig.5/2
B1
B
Vax V-020PU User Guide v2.qxd:Vax V-020(PU) User Guide 17/6/08 10:02 Page 6
Page 7
7
V
ax Careline 0870 606 1248
usage/ troubleshooting / service / specification
6. Usage
Plug in machine to power supply.
Press the red button to turn on the power.
Press the green button to activate the pump.
On the Fibreflow wash head ensure that the rocker
switch (A) is towards the back of the head to allow water
to flow through the head (Fig.6/1).
In order to help suck up excess water, the rocker switch
(A) can be pushed to the front position on the Fibreflow
was head. This will prevent water flow, allowing excess
water to be removed (Fig.6/2).
In order to wash upholstery, including stairs and soft
furnishings simply detach Fibreflow wash head from
wand and solution tube and replace with upholstery
wash tool as shown (Fig.6/3).
NOTE: Do not store cleaner with solution in
clean water tank or dirty water in dirty water
tank. Mineral deposits and mildew can form which
will affect the performance of the carpet washer.
7. Troubleshooting
WARNING: To reduce risk of personal injury,
unplug carpet washer before servicing.
PROBLEM: The cleaner won't run
Cause: Not properly plugged into electrical outlet.
Solution: Plug in firmly.
Cause: No electricity in electrical outlet.
Solution: Check fuse or breaker.
Cause: On/off switch not turned on.
Solution: Push on/off switch to ‘on’.
Cause: Blown fuse/tripped breaker.
Solution: Reset circuit breaker or replace fuse.
PROBLEM: Cleaner/accessories won’t pick up
Cause: Accessories not attached correctly.
Solution: Refer to page 6 for fitting information.
Cause: The hose is clogged.
Solution: Remove the hose and tools. Remove the
obstruction.
8. UK Service & Help
Vax Care 0870 6061248
Monday-Friday 8.00am to 6.00pm
Saturday-Sunday 9.00am to 5.00pm
An answerphone is available outside of these hours. Any
queries or concerns about using the Vax, call the Vax
Careline. Calls are charged at the UK national rate.
Please make a note of the serial number and model
number of the carpet cleaner before calling. There are
over 400 approved Vax Service Agents in the UK. For the
nearest Service Agent, please call the Vax Careline.
www.vax.co.uk
9. Technical Specification
Voltage: 220 ~ 240V 50Hz
Wattage: 1300W
Clean water tank volume: 3 litres
Dirty water tank volume: 4.5 litres
Cord length: 7.5m
Weight: 7.7Kg
Subject to change without notice.
!
!
Fig.6/1
A
A
Fig.6/2
Fig.6/3
!
Vax V-020PU User Guide v2.qxd:Vax V-020(PU) User Guide 17/6/08 10:02 Page 7
Page 8
EEC STATEMENT OF COMPLIANCE
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
V-020PU Carpet Washer is manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive
EMC: 2004/108/EC Electromagnetic Compatibility Directive
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK
email: info@vax.co.uk - website: www.vax.co.uk
Vax V-020PU User Guide v2.qxd:Vax V-020(PU) User Guide 17/6/08 10:02 Page 8
Loading...