www.vax.co.uk
Please read carefully before using this cleaner.
Always fully extend the mains cable before use.
Retain for future reference.
Vax careline
0870 1129 145
Carpet Washer
Vax model number:
VCW-02
(UK only)
instruction manual
VCW-02
1. Diagram
Vax VCW-02
2
parts overview
Fig.1/1
1
2
5
4
3
8
9
6
7
12
11
10
13
1 Carry Handle
2 On/Off Switch
3 Dirty Water Tank
4 Clean Water Tank
5 Clean Water/Solution
6 Lid Release Latch
7 Spray Nozzle
8 Solution Dispense Button
9 Power Cord
10 Attachment Hose
11 Hose Wrap
12 Quick Release Cord Hooks
13 Wash Tool
3
user guide
safety information
2. Safety Information
When using the carpet washer, basic safety precautions
should always be observed, including the following:
1. Do not leave the carpet washer unattended when
plugged in. Unplug it from socket when not in use.
2. To prevent electric shock do not use outdoors.
3. Not to be used as a toy. Close supervision is
necessary when used by or near children or the
infirm.
4. Use only as described in this manual.
5. Do not use with a damaged cord or plug. If the
supply cord and/or plug is damaged, they must be
replaced by the manufacturer, a Vax Service Agent
or similarly qualified persons in order to avoid hazard.
6. Do not pull or carry by the cord, use the cord as a
handle, allow the cord to come into contact with hot
or sharp surfaces or close a door on the cord.
7. Do not unplug by pulling on the cord.
8. Do not handle the plug or carpet washer with wet
hands.
9. Do not put any objects into openings or operate
with openings blocked, keep them free of anything
that may reduce airflow.
10. Keep hair, loose clothing, fingers and all parts of the
body away from openings and moving parts.
11. Do not use the carpet washer on any glowing,
burning or smoking particles.
12. Do not use without the solution tank and dirty
water tank in place.
13. Turn off all controls before unplugging.
14. Do not use to pick up flammable or combustible
liquids such as petrol, or use in areas where they
may be present.
15. Keep the carpet washer on the floor.
16. Do not use an extension cord.
17. Do not attempt to remove blockages with sharp
objects as they may cause damage.
18. Store indoors put away after use to prevent tripping
accidents.
19. Using improper voltage may result in damage to the
motor and possible injury to the user. The correct
voltage is listed on the rating label.
20. A hazard may occur if the carpet washer runs over
the power supply cord.
21. To prevent dirty water from running into motor, do
not hold the appliance upside-down or lay on its
side. Use appliance in normal vacuuming position.
22. Use extra care when cleaning on stairs.
23. Do not carry appliance while motor is running.
NOTE: Carpets should be dry vacuumed
thoroughly before washing.
NOTE: The carpet washer must be unplugged
from the mains socket outlet after use, and
before cleaning or maintaining the carpet washer.
PLEASE KEEP THESE INSTRUCTIONS
FOR FURTHER USE.
!
!
NOTE: Carpets should be dry vacuumed
thoroughly before washing.
NOTE: If the supply cord is damaged, it must be
replaced by the manufacturer, a Vax service
agent or similarly qualified persons in order to avoid
hazard.
NOTE: The carpet washer must be unplugged
from the mains socket outlet after use, and
before cleaning or maintaining the carpet washer.
This appliance is suitable for commercial use, for
example in hotels, schools, hospitals, factories, shops
and offices
PLEASE KEEP THESE INSTRUCTIONS
FOR FURTHER USE.
!
!
!
24. This appliance is not intended for use by
persons ( including children ) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
This appliance is not suitable for picking
up hazardous dust.
immediately.
liquid comes out, switch offIf foam
/
Vax VCW-02
4
preparing the machine
3. Preparing the Machine
WARNING: Use only Vax Commercial Carpet
Cleaner with this machine. Using other cleaning
solutions may cause excessive foaming. Excessive
foam will cause the float to shut off the vacuum
prematurely.
Filling Clean Water Tank
Press down on the Lid. Release Latch and tilt lid towards
front of cleaner to access the tanks (Fig.3/1).
Remove Clean Water Tank by pulling up and out of
cleaner (Fig.3/2).
Unscrew cap and fill Clean Water Tank with solution up
to the Soap Fill Line (Fig.3/3).
Fill the rest of the Clean Water Tank with warm tap
water (MAX 40°C) up to the Water Fill Line (Fig.3/4).
Replace Clean Water Tank cap and tighten firmly.
Return Clean Water Tank to cleaner (Fig.3/5). Close
lid making sure that the Lid Release Latch clicks into
place (Fig.3/6).
Fig.3/1
Fig.3/2
!
Fig.3/3
Fig.3/4
Fig.3/5 Fig.3/6
5
user guide
attachments / usage
4. Attachments
NOTE: Always turn off appliance before
connecting or disconnecting attachments.
Connecting Attachments
Connect desired attachment by pressing tool onto the
end of the attachment hose until the locking button
snaps into the hole (Fig.4/1).
WARNING: Keep spray pointed away from face.
Failure to do so may result in personal injury.
To remove, press down on the locking button and pull
the tool away from the hose (Fig.4/2).
5. Usage
IMPORTANT: Do not use the Carpet Cleaner as
a dry vacuum.
NOTE: Never leave unit unattended with
power on. Turn OFF when emptying and filling
reservoir. DO NOT oversaturate carpet or upholstery.
IMPORTANT: For best cleaning results, use
steady, moderate, forward and backward
motion.
Check for Colour Fastness:
Before cleaning carpet/upholstery, test for colour
fastness. Dampen a white cloth with solution. Test a
small area somewhere discreet i.e. underneath a cushion.
Gently rub the cloth over the area. Check each colour
for colour bleeding. If the cloth remains clean, it should
be safe to clean the carpet/upholstery.
Helpful Hints for Cleaning Carpet:
1. Do not oversaturate carpet with cleaning solution
while using the Carpet Cleaner.
2. For heavily soiled areas, additional applications
may be necessary.
3. Allow plenty of time to dry carpet thoroughly.
4. Wipe cleaning solution from woodwork and wood
to prevent any damage.
5. Try not to walk on carpet until it is completely dry.
6. After carpet is thoroughly dry, vacuum the carpet
using a cleaner with a revolving brushroll.
Carpet and Upholstery Cleaning
Plug cord into electrical outlet (Fig.5/1).
Fig.4/1
Fig.4/2
!!!!!
Fig.5/1
LOCKING BUTTON
Vax VCW-02
6
usage
Turn ON/OFF switch to the “ON” position (Fig.5/2).
Hold the tool approximately 1"above the stained surface.
Press the solution dispense trigger to apply cleaning
solution to the stained area. NOTE: Before using hand
tool attachments, it is necessary to prime the pump.
Follow these steps for optimal performance: (Fig.5/3)
• Fill the clean water tank.
• Place hand tool attachment on floor.
• Depress the solution dispense button on hose for
10 seconds while the power is off.
• Repeat if necessary.
Gently scrub the stained area with the brush on the tool
until the stain is completely removed. Release the
solution dispense trigger and continue moving the tool
over cleaned area to remove as much liquid as possible
(Fig.5/4).
Emptying and Cleaning the Dirty Water Tank
WARNING: To reduce risk of electric shock
or injury, unplug before removing tank(s) and
remove tanks from unit before emptying.
When to empty:
– Dirty water reaches the ‘full’ line on the dirty water
tank - OR
– Float shuts off airflow, indicated by a change in pitch
of the motor and reduced suction
– At the end of each use, prior to storage
Turn ON/OFFswitch to the OFF position. Unplug power
cord from outlet. Press down on the Lid Release Latch
and tilt towards the front of cleaner to access the tanks
(Fig.5/5).
!
Fig.5/4
Fig.5/3
Fig.5/2
Fig.5/5
LID RELEASE
LATCH
7
user guide
usage & troubleshooting
Remove Clean and Dirty Water Tank assembly by pulling
up and out of cleaner and separate Dirty Water Tank
(Fig.5/6).
Open Dirty Water Tank plug and empty contents into sink
(Fig.5/7).
Rinse thoroughly with clean water (Fig.5/8).
6. Troubleshooting
WARNING: To reduce risk of personal injury,
unplug carpet washer before servicing.
PROBLEM: The cleaner won't run
Cause:
Power cord not firmly plugged into socket.
Solution: Plug cord in firmly.
Cause: Blown fuse/tripped breaker.
Solution: Check fuse or breaker in home. Replace
fuse/reset breaker.
PROBLEM: Cleaner won’t pick up or low suction
Cause:
Dirty Water Tank is not installed correctly.
Solution: Review ‘Usage’ section of this user guide.
Cause: Dirty Water Tank is full.
Solution: Empty dirty water tank (for instructions
see ‘Usage’ section of this user guide).
Cause: Incorrect cleaning tool position.
Solution: Reposition cleaning tool, following
instructions from ‘Usage’ section of this
user guide.
Cause: Incorrect cleaning solution.
Solution: Use only Vax AAAcleaning solution.
PROBLEM: Water escaping from cleaner
Cause:
Dirty Water Tank is full.
Solution: Empty dirty water tank (for instructions
see ‘Usage’ section of this user guide).
Cause: Dirty Water Tank is not installed correctly.
Solution: Review ‘Usage’ section of this user guide.
Cause: Clean Water Tank is not installed properly.
Solution: Review ‘Preparing the Machine’ section of
this user guide.
PROBLEM: Cleaner won’t dispense solution or is
dispensing at a low rate
Cause:
Spray nozzle clogged.
Solution: Remove all attachments and clean
thoroughly.
Cause: Clean Water Tank is not installed properly.
Solution: Review ‘Preparing the Machine’ section of
this user guide.
Cause: Solution pump needs priming.
Solution: It may be necessary to prime the pump -
review ‘Usage’ section of this user guide,
or elevate unit above nozzle by placing on
tabletop.
Fig.5/6
Fig.5/7
Fig.5/8
!
Vax VCW-02
7. UK Service & Help
Vax Care 0870 1129 145 (UK only)
Monday-Friday 9.00am to 5.00pm.
An answerphone is available outside of these hours.
Any queries or concerns about using the Vax, call the
Vax Careline. Calls are charged at the UK national rate.
Please make a note of the serial number and model
number of the vacuum cleaner before calling. There are
over 400 approved Vax Service Agents in the UK. For
the nearest Service Agent, please call the Vax Careline.
www.vax.co.uk
8. Technical Specification
Voltage:
Motor Power:
Clean water tank volume:
Dirty water tank volume:
Cord length:
Weight:
Subject to technical change without notice.
220V~240V-50Hz
1.7 litres
1 litre
10.0m
5.4kg
350 W
Subject to technical change without notice.
9. Noise emissions : db
Vax Care 0870 1129 145 (UK only)
Monday-Friday 8.00am to 6.00pm
Saturday-Sunday 9.00am to 5.00pm
An answerphone is available outside of these hours.
Any queries or concerns about using the Vax, call the
Vax Careline. Calls are charged at the UK national rate.
Please make a note of the serial number and model
number of the vacuum cleaner before calling. There are
over 400 approved Vax Service Agents in the UK. For
the nearest Service Agent, please call the Vax Careline.
www.vax.co.uk
8
uk service & help / technical specification
Subject to technical change without notice.
78dB (A)
Noise (IEC60704-2-1):
<
9
user guide
This page has been left intentionally blank.
Vax VCW-02
10
This page has been left intentionally blank.
11
user guide
This page has been left intentionally blank.
EEC STATEMENT OF COMPLIANCE
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the product
VCW-02 Carpet Washer is manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive
EMC: 2004/108/EC Electromagnetic Compatibility Directive
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK
email: info@vax.co.uk - website: www.vax.co.uk
Loading...