Vax Careline:
0870 6061248
Instruction Manual
Please read carefully before using
the washer. Always fully extend
the mains cable before use.
www.vax.co.uk
Vax Model Number V-029
Vax Model Number V-029Q
1. Brushbar switch on/off
2. Mains power switch
on/off
3. Clean water tank cap
(rear of tank)
4. Clean/Dirty water tank
handle
5. Clean/Dirty water tank
latch release
6. Nozzle setting indicator
7. Nozzle base
8. Squeegee
9. Hard floor nozzle
10. Brushbar (underside of
carpet washer)
11. Locking ring
12. Brushbar reset push
13. Solution trigger
14. Carpet nozzle
15. Carry handle
16. Power cord
17. Carpet nozzle storage
18. Quick cord release
19. Nozzle setting pedal
20. Non-marking wheels
21. Handle release pedal
1. Diagram
Parts Overview
22. Vax AAA Carpet Cleaner
NOTE: Always test an inconspicuous area for colour fastness - rub a
small area with a dilute mixture of Vax carpet cleaner on a soft white cloth.
23. Vax Multi Hard Floor Cleaner (CAUTION: TO PREVENT DAMAGE TO
WOOD FLOORS, FOLLOW THE MANUFACTURERS CLEANING
RECOMMENDATIONS. BEFORE USING ON SEALED WOOD FLOOR,
ENSURE THAT SURFACE IS NOT WORN, BARE OR HAS SEPARATED
JOINTS. DO NOT USE IF ANY OF THESE CONDITIONS EXIST.) Do not
use on unsealed wood/laminate floors.
8
10
6
13
14
16
18
9
17
20
20
19
21
15
7
11
12
2
3
4
5
1
2
2. Safety Information
FOR HOUSEHOLD USE ONLY.
When using the cleaner, basic safety precautions should
always be observed, including the following.
1. Do not leave the cleaner unattended when
plugged in. Unplug it from socket when not in use.
2. To prevent electric shock do not use outdoors.
3. Not to be used as a toy. Close supervision is
necessary when used by or near children or the
infirm.
4. Use only as described in this manual.
5. Do not use with a damaged cord or plug. 'If the
supply cord and/or plug is damaged, they must be
replaced by the manufacturer, a Vax Service Agent
or similarly qualified persons in order to avoid hazard.
6. Do not pull or carry by the cord, use the cord as a
handle, allow the cord to come into contact with hot
or sharp surfaces or close a door on the cord.
7. Do not unplug by pulling on the cord.
8. Do not handle the plug or carpet washer with wet
hands.
9. Do not put any objects into openings or operate
with openings blocked, keep them free of anything
that may reduce airflow.
10. Keep hair, loose clothing, fingers, and all parts of
the body away from openings and moving parts.
11. Do not use the cleaner on any glowing, burning or
smoking particles.
12. Do not use without the Clean/Dirty water tank in place.
13. Turn off all controls before unplugging.
14. Do not use to pick up flammable or combustible
liquids such as petrol, or use in areas where they
may be present.
15. Keep the cleaner on the floor.
16. Do not use an extension cord.
17. Do not attempt to remove blockages with sharp
objects as they may cause damage.
18. Store indoors put away after use to prevent
tripping accidents.
19. Using improper voltage may result in damage
to the motor and possible injury to the user.
The correct voltage is listed on the rating label.
20. This cleaner is intended for household use only.
21. A hazard may occur if the carpet washer runs over
the power supply cord.
Safety Information/Use & Function
Fig.1/1
Fig.1/4
Fig.1/3
Fig.1/2
3. Use & Function
Assembling the cleaner
Fig.3/1
3
NOTE: Your cleaner contains a thermal protective
device to shut off the motor to avoid overheating.
If this happens, turn the unit off and unplug the
cleaner. Inspect the nozzle inlet for blockage. Empty
the Dirty Water Tank and clean the filter. After
approximately 30 minutes, the motor will have cooled
and the vacuum will be ready to use.
NOTE: The cleaner must remain unplugged during
the 30 minute cooling period.
22
23
Remove the product from the packaging and gently
push the handle assembly on to the machine body.
Secure with four screws supplied, in the positions
shown. Do not over tighten the screws.
Use & Function
4
Use & Function
Cleaning floors
5
The recommended sequence of cleaning is as follows:
Operating
sequence
Brushbar
Switch
Nozzle
setting
Trigger
switch
Dry
Vacuum
OFF
Released
OFF
Wet
Cleaning
ON
Depressed
ON
Drying
OFF
Released
ON
IMPORTANT: TO PREVENT DAMAGE TO WOOD
FLOORS, FOLLOW THE MANUFACTURERS
CLEANING RECOMMENDATIONS. BEFORE USING
ON SEALED WOOD FLOOR, ENSURE THAT
SURFACE IS NOT WORN, BARE OR HAS
SEPARATED JOINTS. DO NOT USE IN WET
CLEANING MODE WITH THE BRUSHBAR ON.
DO NOT USE IF ANY OF THESE CONDITIONS EXIST.
DO NOT USE ON UNSEALED WOOD/LAMINATE
FLOORS.
Fill
Fig.3/3 Fig.3/4
1. Push down on Clean/Dirty Water Tank latch. Pull
tank up and out. Fig 3/3.
Fig.3/5 Fig.3/6
2. Remove cap from Clean Water Tank. Fig 3/4.
3. Pour 2 capfuls of Vax AAA Carpet Cleaner or Vax
Multi Floor Hard Floor Cleaner concentrate into
solution bottle cap. Fig 3/5 and 3/6.
IMPORTANT: DO NOT USE PINE, SOLVENT, OR
WAX BASED CONCENTRATES IN CLEANER.
4. Fill remainder of Clean Water Tank with warm
[max 40C] water up to the max fill line. Replace
cap on tank. Fig 3/7
.
Fig.3/7 Fig.3/8
5. Replace Clean/Dirty Water Tank into main body of
cleaner. Snap latch to secure. (Fig.3/8).
6. With dry hands, plug cord into properly grounded
electrical outlet. (Fig.3/9).
7. Step on Handle Release pedal to put into cleaning
position. (Fig.3/10).
Fig.3/9 Fig.3/10
8. Turn cleaner on by switching the power on/off
switch [located on the side of the cleaner]. Fig. 3/11.
9. Step on the Nozzle Setting pedal to switch to
select the cleaning option. Fig. 3/12.
ON
OFF
Fig.3/9 Fig.3/10
Emptying and cleaning the dirty water
tank
IMPORTANT: TO REDUCE THE RISK OF INJURY
FROM MOVING PARTS - UNPLUG BEFORE
SERVICING.
Your cleaner is equipped with a shut off valve within
your Dirty Water Tank. Empty the Dirty Water Tank
when the wet and/or dry debris reaches the “Debris
Max Fill” line on the outside of the Clean/Dirty Water
Tank or the float rises, shutting off air flow through
the nozzle.
NOTE: You will hear a noticeable change in the
pitch of the cleaner. This indicates a need to empty
the Dirty Water Tank. The outer tank (Clean Water
Tank) contains the cleaning solution and water mix
while the inner tank (Dirty Water Tank) collects dry
and wet debris.
1. Disconnect cleaner from electrical outlet. Place
cleaner handle in upright and locked position. Fig
3/9.
2. Push down on Clean/Dirty Water Tank latch while
grabbing handle and pulling tank up and out from
main body of cleaner. Fig 3/10
Fig.3/9 Fig.3/10
3. Grasp tab and pull up to remove filter assembly
out of tank. (Fig 3/11) Empty contents into sink.
4. Return the filter back into Clean/Dirty Water Tank.
To ensure a proper fit, make sure arrow on the filter
is aligned with the arrow on Clean Water Tank Cap.
Fig 3/12.
5. Replace Clean/Dirty Water Tank into main body of
cleaner and snap Clean/Dirty Water Tank latch
into place. Fig. 3/13.
Fig.3/11
Fig.3/12
A
L
I
G
N
F
I
L
T
E
R
F
R
O
N
T
Fig.3/13
Fig.3/2
5. Troubleshooting
WARNING: TO REDUCE RISK OF PERSONAL INJURY, UNPLUG CARPET WASHER BEFORE
SERVICING
PROBLEM: Cleaner won’t run.
Cause: Power cord not firmly plugged in.
Solution: Plug unit in.
Cause: The dirty water tank door is not installed correctly.
Solution: Review placing dirty water tank in base of carpet washer.
Cause: Blown fuse or tripped breaker.
Solution: Check fuse or breaker in home. Replace fuse/reset breaker.
Cause: Brush clogged.
Solution: Remove debris from brushbar and push motor reset button.
Cause: Needs service.
Solution: Take to service center or call Vax Care 0870 606 1248.
Cause: Thermal Protector activated.
Solution: Unplug cleaner, allow to cool for 30 minutes before swiching on.
PROBLEM: Cleaner won't pick up or low on suction.
Cause: Clean/Dirty water tank not secured.
Solution: Secure tank.
Cause: Clean/Dirty water tank latch not secured properly.
Solution: Secure latch.
Cause: Dirty water tank full.
Solution: Empty Dirty water tank.
Cause: Dirty water passage is clogged.
Solution: Clean Dirty water tank.
Cause: Filter clogged or dirty.
Solution: Remove filter and clean.
PROBLEM: Water escaping from cleaner.
Cause: Dirty water tank full.
Solution: Empty Dirty water tank.
Cause: Dirty water tank not istalled correctly.
Solution: Insert Clean/Dirty water tank correctly.
PROBLEM: Cleaner won't dispense solution.
Cause: Clean/Dirty water tank not installed correctly.
Solution: Install Clean/Dirty water tank.
Cause: Clean water tank empty.
Solution: Fill Clean water tank.
PROBLEM: Brushbar not rotating.
Cause: Brushes are clogged.
Solution: Unplug unit. Remove debris from brushbar and push reset button on handle.
.Cause: Belt broken.
Solution: Take to a service agent or call Vax Care 0870 606 1248.
Cause: Incorrect nozzle selector.
Solution: Change setting to correct setting.
7
Troubleshooting/UK Service & Help/Technical Specification
Use & Function\Storage
6
With handle in full upright and locked position, tilt cleaner
back on rear wheels and push forward. Use carry handle
on upper cord wrap to move up and down stairs.
BEFORE STORING CLEANER ENSURE THAT:
• Turn off the power switch [located on the side of the
cleaner].
• Nozzle setting is in Hard Floor Dry Vac position.
• Handle is in full upright/locked position.
• After cleaning the water tank, carpet nozzle and hard
floor nozzle should be rinsed with warm water and
thoroughly dried before storage and future use.
Cleaning the filter
Fig.3/14 Fig.3/15
1. Disconnect cleaner from electrical outlet. Place cleaner
handle in upright and locked position. Fig. 3/14.
2. Remove Clean/ Dirty Water. Fig. 3/15.
3. Pull the filter assembly up and out of Clean/dirty water
tank. Fig 3/16.
4. Remove filter by grasping tab and turning
counterclockwise. Lift filter up and out of filter assembly.
Fig 3/17.
5. Remove any loose debris from filter by tapping the filter
against a garbage can. Fig 3/18.
NOTE: For additional cleaning, the filter (Fig 3/19) and
filter assembly (Fig. 3/20) may be rinsed under water.
Allow filter and filter assembly to air dry completely before
use. For filter replacements, please call Vax Care 0870
6061248 or visit www.vax.co.uk to locate a service
agent nearest you.
6. Replace filter by grasping tab and turning clockwise.
(Fig 3/21) Push filter down and into filter assembly.
Return filter assembly back into Clean/Dirty Water
Tank. (Fig 3/22).
Fig.3/16
Fig.3/17 Fig.3/18
Fig.3/19 Fig.3/20
A
L
I
G
N
F
I
L
T
E
R
F
R
O
N
T
Fig.3/21
Fig.3/22
4. Storage
Transporting & storing carpet washer.
EEC STATEMENT OF COMPLIANCE
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the product
Vax V-029/V-029Q Rapide Total Floors are manufactured in compliance
with the following:
Safety: 73/23/EEC Low Voltage Directive, as modified by 93/68/EEC
EMC: 89/336/EEC Electromagnetic Compatibility Directive, as modified by 93/68/EEC
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK
email: enquiry@vax.co.uk - website: www.vax.co.uk
Version 1
7. Technical Specification
Power supply: 220-240/50Hz
Motor power: 550W
Dust container: 0.75 litres
Total water tank volume: 1.5 litres
Filter system: Pleated filter
Cord length: 7.5m
Weight: 6.1kg
Subject to technical change without notice.
6. UK Service & Help
Vax Care 0870 6061248
Monday-Friday. 9.00am to 5.00pm.
An answerphone is available out of these hours.
Any queries or concerns about using the Vax, call the
Vax Careline. Calls are charged at the UK national rate.
Please make a note of the serial number and model
number of the carpet cleaner before calling. There are
over 400 approved Vax Service Agents in the UK. For the
nearest Service Agent, please call the Vax Careline.
www.vax.co.uk
Loading...