Vax V-027CC, V-028CC, Mach Rapide XL V-027CC Instruction Manual
www.vax.co.uk
Please read carefully before using this cleaner.
Always fully extend the mains cable before use.
Retain for future reference.
Vax careline
0870 6061248
instruction manual
Carpet washer
Vax model number:
V-027CC
A
A
A
SOLUTION
2
parts overview
Fig.1/1
www.vax.co.uk
1. Diagram
V-027CC
A
A
A
SOLUTION
1
3
16
21
22
17
19
6
8
12
15
10
2
4
3
4
5
7
20
18
9
11
14
22
13
Solution trigger- There does
not appear to be anything here
in the photo’s
On image 1 you can see a dial here
which has not been picked up on in
the annotated image
29
27
26
25
24
28
1 Handle
2 Solution trigger
3 Brush on/off
4 Power on/off
5 Clean water tank release
6 Clean water tank carry handle
7 Clean water tank
8 Dirty water tank nozzle tab
9 Dirty water tank latch
10 Dirty water tank handle
11 Floor/ tools selector
12 Dirty water tank
13 Hose attachment cover
14 Dual brushbars
15 Front suction nozzle
16 Hose storage
17 Cord wrap
18 Carry handle
19 Cord
20 Lower cord and hose storage
21 Handle release
22 Wheels
23 Hose storage clips
24 Detachable tool storage
25 Uphostery/stair hose
26 Solution tube plug
27 Upholstery/stair wash tool
28 Solution spray trigger
29 Vax AAA Solution
23
23
3
V
ax Careline 0870 606 1248
safety information
2. Safety Information
FOR HOUSEHOLD USE ONLY.
When using the vacuum cleaner, basic safety precautions
should always be observed, including the following:
1. Do not leave the carpet washer unattended when
plugged in. Unplug it from socket when not in use.
2. To prevent electric shock do not use outdoors.
3. Not tobe usedasa toy. Children should be supervisedto
ensure that they do not play with the appliance.
4. This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities,orlack of experience and knowledge,
unless they have been given supervision or instruction
concerning the use of the appliance by a person
responsible for their safety.
5. Use only as described in this manual.
6. Do not use with a damaged cord or plug. If the supply
cord and/or plug is damaged, they must be replaced
by the manufacturer, a Vax Service Agent or similarly
qualified persons in order to avoid hazard.
7. Do not pull or carry by the cord, use the cord as a
handle, allow the cord to come into contact with hot
or sharp surfaces or close a door on the cord.
8. Do not unplug by pulling on the cord.
9. Do not handle the plug or carpet washer with wet
hands.
10. Do not put any objects into openings or operate with
openings blocked, keep them free of anything that
may reduce airflow.
11. Keep hair, loose clothing, fingers and all parts of the
body away from openings and moving parts.
12. Do not use the carpet washer on any glowing,
burning or smoking particles.
13. Do not use without the solution tank and dirty water
tank in place.
14. Do not use the vacuum without the dust bag in place.
15. Turn off all controls before unplugging.
16. Do not use to pick up flammable or combustible
liquids such as petrol, or use in areas where they may
be present.
17. Keep the unit on the floor.
18. Do not use an extension cord.
19. Do not attempt to remove blockages with sharp
objects as they may cause damage.
20. Store indoors put away after use to prevent tripping
accidents.
21. Using improper voltage may result in damage to the
motor and possible injury to the user. The correct
voltage is listed on the rating label.
22. A hazard may occur if the carpet washer runs over
the power supply cord.
23. To prevent dirty water from running into motor, do
not hold the appliance upside-down or lay on its side.
Use appliance in normal vacuuming position.
24. Use extra care when cleaning on stairs.
25. Do not carry appliance while motor is running.
NOTE: Carpets should be dry vacuumed thoroughly
before washing.
NOTE: The unit must be unplugged from the mains
socket outlet after use, and before cleaning or
maintaining the unit.
IMPORTANT: This unit is not intended for
commercial use.
PLEASE KEEP THESE INSTRUCTIONS
FOR FURTHER USE.
!
www.vax.co.uk
4
assembly
3. Assembly
Putting your cleaner together
Remove your Rapide XL from the carton with caution.
The handle is connected to the body by a cord (Fig.3/1).
NOTE: Do not tug or pull on the cord.
Line up the handle to the upper body of the machine and
slide into place (Fig.3/2).
NOTE: Phillips screwdriver required
Secure from the back with the two smaller screws
(Fig.3/3).
Feed the cord through the slots on the back of the
handle and push into place (Fig.3/4).
Place a nut into the recess in the back of the upper
handle. While holding the nut in place insert one of the
large screws through the front of the upper handle and
tighten (Fig.3/5).
Repeat the process with the second screw.
Remove the backing tape from the screw cover and press
into place (Fig.3/6).
Fig.3/1
Fig.3/4
Fig.3/5
Fig.3/2
Fig.3/6
Fig.3/3
Loading...