Vax V-020/V-020TF, WashVax V-020, WashVax V-020TF Instruction Manual

Vax Careline:
0870 6061248

Instruction Manual

Please read carefully before using

the cleaner. Always fully extend

the mains cable before use.

Please retain these instructions

for future reference.

www.vax.co.uk

Carpet Washer
Vax Model Number: V-020/V-020TF

V-020(TF) User Guide.qxd 4/9/06 14:43 Page 2

1. Diagram

Parts Overview

5

2

1

3

6

7

2

1. Power Button (Red)

2. Water Pump Button (Green)

3. Carry Handle

4. Power Cord

5. Container Release Clips

6. Casters

7. Hose Connection Port

8. Solution Tube Port

9. Exhaust Filter

10. Hose
10a. Hose to Cylinder Connector

11. Solution Tube
11a. Solution Tube to Cylinder Connector
11b. Solution Tube to Wash Head /

Upholstery Tool Connector

12. Telescopic Tube

13. Fibreflow Wash Head

14. Hydrodry Hard Floor Wash Head

15. Upholstery Wash Tool

16. Vax AAA Carpet Cleaner

17.

Vax Multi Hard Floor Cleaning Solution

4

Fig.1/2

Fig.1/1

Fig.1/6

Fig.1/4 Fig.1/5

Fig.1/3

AAA

ANTI

ALLERGEN

ADDITIVE

multi

8

9

10

11

10a11a

11b

13

1514

16 17

12

V-020(TF) User Guide.qxd 4/9/06 14:43 Page 3

3

S

afety Information / Preparing the Carpet

2. Safety Information

FOR HOUSEHOLD USE ONLY
When using the carpet washer, basic safety
precautions should always be observed, including the
following:

1. Do not leave the carpet washer unattended when
plugged in. Unplug it from socket when not in use.

2. To prevent electric shock do not use outdoors.

3. Not to be used as a toy. Close supervision is
necessary when used by or near children or the
infirm.

4. Use only as described in this manual.

5. Do not use with a damaged cord or plug. If the
supply cord and/or plug is damaged, they must
be replaced by the manufacturer, a Vax Service
Agent or similarly qualified persons in order to
avoid hazard.

6. Do not pull or carry by the cord, use the cord as
a handle, allow the cord to come into contact with
hot or sharp surfaces or close a door on the cord.

7. Do not unplug by pulling on the cord.

8. Do not handle the plug or carpet washer with wet
hands.

9. Do not put any objects into openings or operate
with openings blocked, keep them free of
anything that may reduce airflow.

10. Keep hair, loose clothing, fingers and all parts of
the body away from openings and moving parts.

11. Do not use the carpet washer on any glowing,
burning or smoking particles.

12. Do not use without the solution tank and dirty
water tank in place.

13. Turn off all controls before unplugging.

14. Do not use to pick up flammable or combustible
liquids such as petrol, or use in areas where they
may be present.

15. Keep the carpet washer on the floor.

16. Do not use an extension cord.

17. Do not attempt to remove blockages with sharp
objects as they may cause damage.

18. Store indoors put away after use to prevent
tripping accidents.

19. Using improper voltage may result in damage to
the motor and possible injury to the user. The
correct voltage is listed on the rating label.

20. A hazard may occur if the carpet washer runs
over the power supply cord.

NOTE: Carpets should be dry vacuumed
thoroughly before washing.

NOTE: If the supply cord is damaged, it must be
replaced by the manufactur

er

, a V

ax service agent

or similarly qualified persons in order to avoid
hazard.

NOTE: The carpet washer must be unplugged from
the mains socket outlet after use, and before
cleaning or maintaining the carpet washer.

IMPORTANT: This carpet washer is not intended
for commercial use.

3. Preparing the Carpet

IMPORTANT: DO NOT USE THE CARPET WASHER
AS A DRY VACUUM.

1. Vacuum carpet thoroughly. Use a vacuum cleaner
with a revolving brushbar for best results.

2. Remove as much furniture from the room as
possible. If unable to remove the furniture, place
plastic or foil under and around the legs until the
carpet has dried completely.

HELPFUL HINTS FOR CLEANING CARPET:

1. Only use Vax recommended carpet cleaner with
this carpet washer.

2. Do not oversaturate carpet with cleaning solution
while using the carpet washer.

3. For heavily soiled areas, additional applications
may be necessary.

4. Allow plenty of time to dry carpet thoroughly.

5. Wipe cleaning solution from woodwork and wood
to prevent any damage.

6. Try not to walk on carpet until it is completely dry.

7. After carpet is thoroughly dry, vacuum the carpet
using a vacuum cleaner with a revolving brushbar.

8. Before cleaning, determine where to start and
end, making sure not to walk over previously
cleaned areas.

CHECK FOR COLOUR FASTNESS:

Before cleaning carpet, test for colour fastness.
Dampen a white cloth with solution. Test a small area
in a closet. Gently rub the cloth over the area. Check
each colour for colour bleeding. If the cloth remains
clean, it should be safe to clean the carpet.

AFTER CLEANING:

• Allow carpet to dry completely. Try not to walk on
the carpet until it is dry.

•

If it is necessary to walk on the carpet, place
white towels on the areas to be walked on.

• If the carpet is not dry and the furniture must be
placed back in the r

oom, use plastic or foil under

the fur

nitur

e to prevent staining the carpet.

• Thoroughly clean the dirty water tank with warm
(max 40ºC) tap water

.

V-020(TF) User Guide.qxd 4/9/06 14:43 Page 4