EEC STATEMENT OF COMPLIANCE
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
V-020 series carpet cleaner is manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive
EMC: 2004/108/EC Electromagnetic Compatibility Directive
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
Washvax
Let’s get started
V-020 Series
vax.co.uk
Parts overview
9
1
2
3
4
14
15
5
8
7
6
10
12
1 Power button (red)
2 Water pump button (green)
3 Carry handle
17
18
16
4 Power cord
5 Lid release clips
6 Casters
7 Hose connection port
13
11
8 Solution tube port
9 Exhaust filter (hidden)
10 Hose (loose in box)
11 Hose cylinder connector
12 Solution tube
13 Solution tube connector
13
14 Fibreflow wash head
15 Wash tool
16 Upholstery tool
17 Vax carpet cleaning solution
18 2 piece extension tube
2
For Household Use Only
When using the carpet cleaner, basic safety precautions
should always be observed, including the following:
1. Do not leave the carpet cleaner unattended when
plugged in. Unplug it from socket when not in use.
2. To prevent electric shock do not use outdoors.
3. Not to be used as a toy. Close supervision is
necessary when used by or near children or the
infirm.
4. Use only as described in this manual.
5. The appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
6. Do not use the carpet cleaner if it has been
dropped, damaged, left outdoors or dropped into
water. Do not use the carpet cleaner with a
damaged cord or plug. If the supply cord is
damaged, it must be replaced by the manufacturer
or a recommended Service Agent to avoid hazard
and invalidating the guarantee.
7. Do not pull or carry by the cord, use the cord as a
handle, allow the cord to come into contact with
hot or sharp surfaces or close a door on the cord.
8. Do not unplug by pulling on the cord.
9. Do not handle the plug or carpet cleaner with wet
hands.
10. Do not put any objects into openings or operate
with openings blocked, keep them free of anything
that may reduce airflow.
11. Keep hair, loose clothing, fingers and all parts of
the body away from openings and moving parts.
12. Do not use the carpet cleaner on any glowing,
burning or smoking particles.
13. Do not use without the clean water tank and dirty
water tank in place.
14. Turn off all controls before unplugging.
15. Do not use to pick up flammable or combustible
liquids such as petrol, or use in areas where they
may be present.
16. Keep the carpet cleaner on the floor.
17. Do not use an extension cord.
18. Do not attempt to remove blockages with sharp
Safety information
objects as they may cause damage.
19. Store indoors put away after use to prevent
tripping accidents.
20. Using improper voltage may result in damage to
the motor and possible injury to the user. The
correct voltage is listed on the rating label.
21. A hazard may occur if the carpet cleaner runs
over the power supply cord.
NOTE: Carpets should be dry vacuumed thoroughly
before washing.
NOTE: If the supply cord is damaged, it must
be replaced by the manufacturer or a Vax
service agent in order to avoid hazard and
invalidating the guarantee.
NOTE: The carpet cleaner must be unplugged from
the mains socket outlet after use, and before cleaning
or maintenance.
IMPORTANT: This carpet cleaner is not intended for
commercial use.
vax.co.uk
3
Preparing the carpet
IMPORTANT: Do not use the carpet cleaner as a dry
vacuum.
1. Dry vacuum carpet thoroughly.
2. Remove as much furniture from the room as
possible. If you are unable to remove the furniture,
place plastic or foil under and around the legs until
the carpet has dried completely.
Helpful Hints for Carpet Cleaning:
1. Only use Vax carpet cleaning solution with this
carpet cleaner.
2. Do not saturate carpet with cleaning solution while
using the carpet cleaner.
3. For heavily soiled areas, additional applications may
be necessary.
4. Allow plenty of time to dry carpet thoroughly.
5. Wipe cleaning solution from woodwork and wood
to prevent any damage.
6. Try not to w alk on carpet until it is completely dry.
7. After carpet is thoroughly dry, vacuum the carpet
using a vacuum cleaner with a revolving brushbar.
8. Before cleaning, determine where to start and end,
making sure not to walk over previously cleaned
areas.
Check for Colour Fastness:
Before cleaning carpet, test for colour fastness. Dampen
a white cloth with solution. Test a small area in a closet.
Gently rub the cloth over the area. Check each colour
for colour bleeding. If the cloth remains clean, it should
be safe to clean the carpet.
Pull down the tab before lifting the lower clip (Fig.4/1).
1
2
Fig.4/1
Lift off lid to reveal clean water tank (A) situated inside
dirty water tank (B) (Fig.4/2).
A
B
Fig.4/2
Remove clean water tank from inside dirty water tank
and fill with warm (max 40ºC) water to point indicated
on tank. Add 1 capful of Vax carpet cleaning solution per
litre of water (Fig.4/3).
B
A
Fig.4/3
4
!
!
Assembly
Replace clean water tank (A) inside dirty water tank (B)
taking care to ensure that the space to allow the dirty
water back into the tank is lined up with the solution
port (C) (Fig.4/4).
A
B
C
Fig.4/4
Replace lid ensuring that the solution pump hose is
aligned with the hole in the clean water tank (C) so that
it goes inside when the motor container is clipped back
into position (Fig.4/5).
Push solution tube cylinder connector (A) firmly into
solution port (A1).
Twist solution tube cylinder connector (A1) a quarter
turn to the right to lock into place (Fig.5/1).
A1
A
Fig.5/1
Push hose cylinder connector (B) firmly into hose
connection port (B1). Twist to the right until hose
cylinder connector locks into place (Fig.5/2).
B1
B
Fig.4/5
Push down clips and secure lid. Push tabs up to latch
into place (Fig.4/6).
1
2
Fig.4/6
WARNING: Machine must not be plugged in during
this stage.
vax.co.uk
Fig.5/2
5
Preparing the carpet Usage
Wrap solution tube (A) around hose (B). Ensure that
the solution tube is wrapped loosely enough to allow
the solution to flow freely through the tube (Fig.5/3).
B
A
Fig.5/3
After wrapping the tube around the hose, affix solution
tube (A) to hose (B) using clips provided (C) to hold it
in place (Fig.5/4).
A
B
Plug in machine to power supply.
Press the red button to turn on the power.
Press the green button to activate the pump.
On the Fibreflow wash head ensure that the rocker
switch (A) is towards the back of the head to allow
water to flow through the head (Fig.6/1).
A
Fig.6/1
In order to help suck up excess water, the rocker switch
(A) can be pushed to the front position on the Fibreflow
wash head. This will prevent water flow, allowing
excess water to be removed (Fig.6/2).
A
Fig.6/2
C
Fig.5/4
Push end of solution tube onto connective valve
on the wash head/upholstery tool (Fig.5/5).
Fig.5/5
6
In order to wash upholstery, including stairs and soft
furnishings, simply detach Fibreflow wash head from
wand and solution tube and replace with wash tool as
shown (Fig.6/3).
Fig.6/3
NOTE: Do not store cleaner with solution in clean
water tank or dirty water in dirty water tank. Mineral
deposits and mildew can form which will affect the
performance of the cleaner.
NOTE: For extra extraction, detach wash tool
head from wand and solution tube and attach the
upholstery tool to the end of the wand.
WARNING: To reduce risk of personal injury, unplug
carpet cleaner before servicing.
PROBLEM: The cleaner won’t run
Cause: Not properly plugged into electrical outlet.
Solution: Plug in firmly.
Cause: No electricity in electrical outlet.
Solution: Check fuse or breaker.
Cause: On/off switch not turned on.
Solution: Push on/off switch to ‘on’.
Cause: Blown fuse/tripped breaker.
Solution: Reset circuit breaker or replace fuse.
PROBLEM: Cleaner/accessories won’t pick up
Cause: Accessories not attached correctly.
Solution: Refer to page 6 for fitting information.
Cause: The hose is clogged.
Solution: Remove the hose and tools. Remove the
obstruction.
UK Service & Help
Technical specicationUsage Troubleshooting
Voltage: 220 ~ 240V 50Hz
Wattage: 1300W
Clean water tank volume: 4 litres
Dirty water tank volume: 4 litres
Cord length: 10m
Weight: 7.7Kg
Subject to change without notice.
Vax Careline (UK) 0844 412 8455
(ROI) 1-800 928 308
Monday-Friday 8.30am to 6.30pm
Saturday-Sunday 9.00am to 5.00pm
If you have any queries or concerns about using your
Vax, call the VaxCareline. Calls are charged at the UK
local rate.
Please make a note of the serial number and model
number of the carpet cleaner before calling. For the
nearest Service Agent, please call the Vax Careline or
visit vax.co.uk
vax.co.uk
7
Loading...