TT
Vax V-015 User Guide.qxd 22/9/06 12:17 Page 1
Upright
V-015
Vax careline
0870 6061248
Bagless upright vacuum cleaner
Vax model number: V-015
www.vax.co.uk
Please read carefully before using this cleaner.
Always fully extend the mains cable before use.
or future reference.
tain f
e
R
instruction manual
Vax V-015 User Guide.qxd 22/9/06 12:17 Page 2
Vax V-015
1. Diagram
1
2
12
3
4
5
6
7
8
9
Fig.1/1
1 Handle
2 TurboTool®
3 Dirt container lid
4 Dirt Container
5 Extension tube
6 Dirt container release button
ool
vice t
e
Cr
7
8 Carpet height adjuster
Wheel
9
10 Filter
Vacuum head
11
10
11
13
16
14
17
15
12 Dusting Brush
13 Super stretch hose
14 Power Cord
15 Handle release pedal
16 Upper cord wrap with quick release
17 Hose connector
2
parts overview
!!!!!
Vax V-015 User Guide.qxd 22/9/06 12:17 Page 3
user guide
2. Safety Information
FOR HOUSEHOLD USE ONLY.
When using the vacuum cleaner, basic safety precautions
should always be observed, including the following:
1. Only use the vacuum cleaner indoors on dry surfaces.
2. Turn off the vacuum cleaner controls before
connecting to or disconnecting from the mains
supply.
3. Always unplug the vacuum cleaner before connecting or
disconnecting the vacuum hose.
4. Use only as described in this manual. Use only the
manufacturer’s recommended attachments.
5. Close attention is necessary when used by or near
children. Do not allow children to use as a toy.
6. Do not use the vacuum cleaner with a damaged cord
or plug. Do not use the vacuum cleaner if it has been
dropped, damaged, left outdoors or dropped into
water. Return the vacuum cleaner to a Vax
Authorised Service Agent or suitably qualified person
for examination, repair or adjustment.
7. Do not pull or carry by the cord. Do not use the cord
as a handle, close a door on the cord or pull the cord
around sharp edges or corners. Do not run the
vacuum cleaner over the cord. Keep the cord away
from heated surfaces.
8. Do not handle the plug or vacuum cleaner with wet
hands. Do not use outdoors or on wet surfaces.
9. Do not put any objects into openings. Do not use
with any openings blocked and do not restrict air
flow. Keep all openings free of dust, lint, hair or
anything that may reduce airflow.
10. Keep hair, loose clothing, fingers and all parts of the
body away from openings and moving parts.
11. Do not pick up hot coals, cigarette butts, matches or
any hot, smoking or burning objects.
12. Do not pick up flammable or combustible materials
(lighter fluid, petrol, kerosene, etc) or use in the
presence of explosive liquids or vapours.
13. Do not vacuum up harmful or toxic material
(chlorine bleach, ammonia, drain cleaner, etc).
14. Do not vacuum up hard or sharp objects such as glass,
nails, screws, coins, etc.
15. Do not use without the filters in place.
16. Use extra care when vacuuming on stairs.
17. Keep vacuuming area well lit.
18. Store the vacuum cleaner indoors in a cool,
19. Turn off the switch before unplugging.
dry ar
ea.
20. Use only CE-approved 13 amp extension cords. Non-
approved extension cords may overheat. Care should
be taken to arrange the cord so that the cord cannot
be pulled or tripped over.
WARNING: Always switch off and unplug the
vacuum cleaner from the electrical outlet before
assembling, opening or emptying the dirt container, or
before connecting/disconnecting the attachments.
CAUTION: The vacuum cleaner is a very powerful
unit. Before plugging the cord into the outlet make
sure the switch is in the ‘off’ position. Hold the vacuum
cleaner firmly when starting and in use.
IMPORTANT: If the vacuum inlet or hose is blocked,
switch off the vacuum cleaner and remove the
blockage(s) before re-starting the vacuum cleaner.
IMPORTANT: Cleaning filters improves vacuum
performance. Make sure all filters are replaced back
into the vacuum cleaner before using.
IMPORTANT: The motor is equipped with a thermal
cut-out. If, for any reason, the vacuum cleaner
should over-heat, the thermostat will automatically
turn the unit off. Should this occur, unplug the
vacuum cleaner from the electrical outlet and turn off the
switch. Remove the dirt container and empty.
Clean the filters. Allow the cleaner to cool for
approximately one (1) hour. To re-start, plug into the
electrical outlet and switch back on.
This vacuum cleaner is intended for household use only
and not for commercial or industrial use.
PLEASEKEEPTHESE INSTRUCTIONSFOR FURTHERUSE.
safety information
3
!
!
Vax V-015 User Guide.qxd 22/9/06 12:17 Page 4
Vax V-015
ord storage: To neatly store the power cord, wrap
3. Use and Function
Slide the handle onto the top of the main body of the
vacuum.
Insert double pronged hole cover into front screw holes
(located behind the carry handle.
Secure in place using the two long Phillips head screws
provided.
Assembly of the Hose: Screw in appropriate end of the
hose into the hold in between the cord holders. Feed hose
through the base holding point, clip into side clip, loop over
top holding point (see Fig.3/1) and feed into hose
connector (see Fig.3/2).
C
around the two cord holders and then using the clip (found
just below the plug head) attach to the cord itself.
To turn on the vacuum press the on/off switch located
midway up on the right hand side. Pressing this switch
again turns off the cleaner.
To adjust the angle of the main body push the release
pedal on the lower left side of the cleaner. This then frees
the movement of the unit for greater mobility (Fig.3/3).
Fig.3/3
To adjust the brush bar for improved cleaning on varying
Fig.3/1
Fig.3/2
4
use and function
surfaces, turn the carpet height adjuster to the
appropriate position. This is found on the base of the unit,
in the centre, above the brush bar window.
IMPORTANT: When using the tools and the cleaner
is in the upright position, the adjuster must be set
to the highest position.
WARNING: To avoid injury keep lose clothing, hair,
fingers an all other parts of the body away from the
moving parts (i.e. the brush bar) of the cleaner.
The accessories can be used with or without the
extension tube. To attach, remove the hose from the
machine (see Fig.3/4) and push the desired accessory onto
the end.
!
!
Vax V-015 User Guide.qxd 22/9/06 12:17 Page 5
Fig.3/4
The accessories provided are as follows:
Crevice Tool: Use the crevice tool for radiators, crevices,
corners, skirting boards and between cushions. Dusting
Brush: Ideal for window sills, curtains, shelving, and
general dust lifting off furniture and fittings around the
home.
TurboTool: For pet hairs, stairs and upholstery. The
TurboTool should be pulled backwards across the surface
that is being cleaned for optimum performance.
Fig.4/1
Empty all the dirt from the dirt container using the quick
release button at the base of the container (see Fig.4/2).
user guide
4. Dirt container and filter
removal and replacement
IMPORTANT: Always unplug the unit from the
electrical outlet before opening the dirt container.
IMPORTANT: Do NOT use the vacuum without the
HEPA filter in place. To remove the dirt container,
press the dirt container release button and lift away from
the vacuum cleaner.
Cleaning the HEPA filter
Remove dirt container lid by grasping the dirt container
(see Fig.4/1) and turning anti clockwise.
dirt container and filter removal and replacement
Fig.4/2
5
!
!
Vax V-015 User Guide.qxd 22/9/06 12:17 Page 6
Vax V-015
Remove the lid of the dirt container (see Fig.4/3).
Fig.4/3
Firmly tap clean the HEPA filter (see Fig.4/4) until no more
dust is observed falling out.
ARNING: Always empty dirt container and clean
W
HEPA filter before each use and during prolonged
usage to avoid motor damage.
Cleaning the pre-motor filter
Behind the dirt container, just under the carry handle is a
pre-motor filter in the form of a small rectangle shaped
piece of foam. This can be cleaned in the same way as the
HEPA filter and can also be had washed under the cold tap.
PLEASE NOTE: Let the filter dry out side the
vacuum for 24 hours before replacing / re-using.
The dirt container can be washed in lukewarm water (max
40°C). Do not use strong detergents and ensure dirt
container is fully dry before putting back in vacuum
cleaner.
Fig.4/4
6
dirt container and filter removal and replacement
Vax V-015 User Guide.qxd 22/9/06 12:17 Page 7
5. Maintenance
Cleaning and Changing the Belt
WARNING:
maintenance on the cleaner to reduce chance of an
electric shock.
1. Turn vacuum off and unplug from power supply. Press
2. Using a Phillips screwdriver, remove the two screws on
Fig.5/1
Always turn power off before performing any
handle release button and recline vacuum to lowest
level and lie on a flat surface.
the topside of the cleaning head (see Fig.5/1) to
release the top cover. (see Fig.5/2)
Fig.5/3
4. Remove broken/ worn belt from the motor drive shaft.
5. Remove all belt residue that my exist in the belt area
before replacing with a new belt.
6. Loop the new belt first over the motor drive shaft and
then over the agitator pulley.
7. Insert the brush bar back into its slots. Press firmly on
both sides to make sure either end is completely inserted.
8. Check to make sure that the belt is centred on the
agitator pulley and that the brush bar turns.
9. Replace the vacuum head cover by screwing in the 2
screws on the topside.
user guide
Fig.5/2
3. Lift either side of the brush bar to remove from the
cleaning head (see Fig.5/3).
Removing blockages from the TurboTool
Rotate the locking ring 180°, then turn the TurboTool over.
Pivot the lower housing open and then remove any
obstructions To reassemble, ensure the tabs are engaged,
pivot the housing closed and reposition the locking ring.
maintenance
7
!
!
Vax V-015 User Guide.qxd 22/9/06 12:17 Page 8
Vax V-015
6. Troubleshooting
WWAARRNNIINNGG::
TO REDUCE RISK OF PERSONAL INJURY UNPLUG VACUUM CLEANER BEFORE SERVICING
PROBLEM: Cleaner won’t run
Cause: Not properly plugged into electrical outlet.
Solution: Plug cord in firmly.
Cause: No electricity in wall outlet.
Solution: Check fuse or breaker.
Cause: On/off switch not turned on.
Solution: Push on/off switch to on.
Cause: Motor thermostat tripped.
Solution: Reset motor thermostat (see page 3).
Cause: Blown fuse/tripped breaker.
Solution: Reset circuit breaker or replace fuse.
PROBLEM: Cleaner won't pick up
Cause: Full or clogged dirt container.
Solution: Clean dirt container.
Cause: Wrong pile height setting.
Solution: Adjust setting on carpet height adjuster.
Cause: Clogged nozzle.
Solution: Remove obstruction.
Cause: Clogged dirt inlet.
Solution: Remove power head cover and remove obstruction.
Cause: Clogged hose.
Solution: Remove obstruction.
Cause: Broken belt.
Solution: Replace belt.
Cause: Hose not inserted fully.
Solution: Push hose in securely.
Cause: Dirty filters.
Solution: Clean/change filters.
PROBLEM: Accessories won't pick up
Cause: Accessories not attached correctly.
Solution: Refer to section 5 for fitting information.
PROBLEM: Cleaner picks up moveable rugs or pushes too hard
Cause: Wrong pile height setting.
Solution: Adjust setting on carpet height adjuster.
PROBLEM: Brushbar does not turn
Cause: Broken belt.
Solution: R
Cause: Belt installed incorrectly.
Solution: Check belt.
eplace belt.
PROBLEM: Air flow restricted with attachment use
tricts air flo
es
ttachmen
Cause: A
Solution: Check attachment.
Cause: New carpet debris clogging air path.
Solution: Remove obstruction.
t use r
w.
8
troubleshooting
Vax V-015 User Guide.qxd 22/9/06 12:17 Page 9
user guide
7. UK Service & Help
Vax Care 0870 6061248
Monday-Friday. 9.00am to 5.00pm.
An answerphone will be available out of these hours. Any
queries or concerns about using your Vax, call the Vax
Careline. Calls are charged at the UK national rate.
Please make a note of the model number and serial number
of your Vax before calling. There are over 400 approved
Vax Service Agents in the UK. For the nearest Vax Service
Agent, please call the Vax Careline or visit
www.vax.co.uk
8. Technical Specification
Voltage: 220 ~ 240V 50Hz
Wattage: 1600W
Capacity: 2.0 litres
Filters: Pleated paper HEPA filter
Pre-motor
Cord length: 9.0m
Weight: 7.0kg
Subject to technical change without notice.
uk service & help / technical specification
9
Vax V-015 User Guide.qxd 22/9/06 12:17 Page 10
Vax V-015
This page has been left intentionally blank.
10
Vax V-015 User Guide.qxd 22/9/06 12:17 Page 11
user guide
This page has been left intentionally blank.
11
Vax V-015 User Guide.qxd 22/9/06 12:17 Page 12
EEC STATEMENT OF COMPLIANCE
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the
te electrical products should not be disposed of with household waste. Please recycle where
as
W
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK
V-015 is manufactured in compliance with the following Directives:
Safety: 73/23/EEC Low Voltage Directive
EMC: 89/336/EEC Electromagnetic Compatibility Directive
facilities exist. Check with your Local Authority or retailer for recycling advice.
email: info@vax.co.uk - website: www.vax.co.uk
Loading...